Diff: mcp4728.h

Revision:

0:7a0ebc527fb9

Child:

1:cd7c70a46739

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/mcp4728.h	Fri Oct 23 19:35:27 2015 +0000
@@ -0,0 +1,123 @@
+#ifndef MCP_4728_H
+#define MCP_4728_H
+
+
+#include "stdbool.h"
+
+#include "dev_interface_def.h"
+#include "I2CInterface.h" 
+#include "DACInterface.h" 
+
+#define VERSION_MCP4728_HDR "0.01"
+
+/** MCP4728 class.
+ *  Used for interfacing with a mcp4728 12-Bit QUAD  Digital-to-Analog Converter.
+ *  To convert between the 12bit dac_value and Vout, use the following formula: dac_value = (Vout*4096/Vref), where Vout is  
+ *  the desired output analog voltage, Vref is the voltage connected to the Vdd pin of the device. Typically Vdd will be 3.3volts.
+ *
+ * (C) Wim Beaumont Universiteit Antwerpen 2015        
+ *  
+ */
+class MCP4728 : public DACInterface
+{
+    float vref ;
+    
+    
+    public:
+    /** The device supports two types of power modes: normal and power-down. In normal mode the device
+     * operates a normal digital to analog conversion. In power-down mode all digitial to analog  
+     * conversion is stopped, resulting in the device using less power (typically 60nA). Also, in power 
+     * down mode Vout will be pulled to ground using either a 1k, 100k or 500k ohm internal resistors. */
+    enum PowerMode {
+        /** In normal mode the device operates a normal D2A conversion. */
+        Normal=0,
+        /** Enter the device into a power down mode, and pull Vout to ground using an internal 1k resistor. */
+        PowerDown1k=1,
+        /** Enter the device into a power down mode, and pull Vout to ground using an internal 100k resistor. */
+        PowerDown100k=2,
+        /** Enter the device into a power down mode, and pull Vout to ground using an internal 500k resistor. */
+        PowerDown500k=3
+    };
+    
+    
+    
+    enum VrefMode {
+        ExternRef=0,  // == VDD 
+        InternRef=1
+        
+    };
+    
+    
+    enum GainMode {
+        GainX1=0,
+        GainX2=1
+    };
+    
+    typedef struct MCP4728ChCfg{
+         GainMode gain;
+         VrefMode  vref;
+         PowerMode pwr;
+    } MCP4728ChCfgdummy;
+    
+    MCP4728ChCfg ChCfg[4];
+        
+    
+    /** The device supports 3 different I2C bus frequencies.*/
+    enum BusFrequency {
+        /** Standard 100kHz bus. */
+        Standard100kHz,
+        /** Fast 400kHz bus. */
+        Fast400kHz,
+        /** High Speed 3.4Mhz bus. WARNING: the test suite fails for the mbed LPC1768 when this frequency is selected - not tested on other platforms.*/
+        HighSpeed3_4Mhz
+    };
+    
+    /** Create an mcp4725 I2C interface
+     * 
+     * @param i2cinterface pointer to the  MBED I2C interface 
+     * @param scl I2C clock line pin
+     * @param bus_frequency the frequency at which the I2C bus is running.
+     * @param device_address_bits The 3bit address bits of the device.
+     */
+    MCP4728(I2CInterface* i2cinterface,  int device_address_bits);
+    
+    
+    /* Update the power mode and DAC value.
+     *
+     * @param   mode The Power mode to set the device into.
+     * @param   dac_value The 12bit dac register data value.
+     * @param   writeToEeprom True if the config is to be stored 
+     *          in eeprom, otherwise false
+     * 
+     * @returns 
+     *       0 on success,
+     *   non-0 on failure
+     */
+    int write(enum PowerMode mode, int dac_value, bool writeToEeprom);
+    
+        
+    /** Read the contents of the dac register, the contents of eeprom, and if an eeprom write is currently active.
+     * 
+     * @param   mode Pointer to variable to store the current power mode.
+     * @param   mode_eeprom Pointer to variable to store the power mode as is stored in eeprom.
+     * @param   dac_value Pointer to variable to store the current dac value.
+     * @param   dac_value_eeprom Pointer to variable to store the dac value as is stored in eeprom.
+     * @param   eeprom_write_in_progress Pointer to variable to store the current eeprom write status.
+     *
+     * @returns 
+     *       0 on success,
+     *   non-0 on failure
+     */
+    int read(enum PowerMode& mode, enum PowerMode& mode_eeprom, int& dac_value, int& dac_value_eeprom, bool& eeprom_write_in_progress);
+    
+    virtual int getDACvalue(int &value, int ch=0);
+    virtual int setDACvalue( int value, int ch=0);
+    protected:
+    /** mbed I2C interface driver. */
+    I2CInterface* _i2c_interface;
+    /** The full i2c device address. */
+    int _device_address;
+    
+};
+
+#endif
\ No newline at end of file