Diff: easy-connect/stm-spirit1-rf-driver/source/libs/Contiki_STM32_Library/stm32l-spirit1-config.h

Revision:

0:a1734fe1ec4b

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/easy-connect/stm-spirit1-rf-driver/source/libs/Contiki_STM32_Library/stm32l-spirit1-config.h	Sat Apr 08 14:43:14 2017 +0000
@@ -0,0 +1,98 @@
+/**
+  ******************************************************************************
+  * @file    stm32l-spirit1-config.h
+  * @author  MCD Application Team
+  * @version V3.4.0
+  * @date    29-June-2012
+  * @brief   Evaluation board specific configuration file.
+  ******************************************************************************
+  * @attention
+  *
+  * <h2><center>&copy; COPYRIGHT 2012 STMicroelectronics</center></h2>
+  *
+  * Licensed under MCD-ST Liberty SW License Agreement V2, (the "License");
+  * You may not use this file except in compliance with the License.
+  * You may obtain a copy of the License at:
+  *
+  *        http://www.st.com/software_license_agreement_liberty_v2
+  *
+  * Unless required by applicable law or agreed to in writing, software 
+  * distributed under the License is distributed on an "AS IS" BASIS, 
+  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+  * See the License for the specific language governing permissions and
+  * limitations under the License.
+  *
+  ******************************************************************************
+  */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32L_SPIRIT1_CONFIG_H
+#define __STM32L_SPIRIT1_CONFIG_H
+
+/* Includes ------------------------------------------------------------------*/
+
+/* Exported types ------------------------------------------------------------*/
+/* Exported constants --------------------------------------------------------*/
+
+/* Define the STM32F10x hardware depending on the used evaluation board */
+#ifdef USE_STM3210B_EVAL
+  #define USB_DISCONNECT                      GPIOD  
+  #define USB_DISCONNECT_PIN                  GPIO_PIN_9
+  #define RCC_APB2Periph_GPIO_DISCONNECT      RCC_APB2Periph_GPIOD
+  #define EVAL_COM1_IRQHandler                USART1_IRQHandler 
+
+#elif defined (USE_STM3210E_EVAL)
+  #define USB_DISCONNECT                      GPIOB  
+  #define USB_DISCONNECT_PIN                  GPIO_PIN_14
+  #define RCC_APB2Periph_GPIO_DISCONNECT      RCC_APB2Periph_GPIOB
+  #define EVAL_COM1_IRQHandler                USART1_IRQHandler 
+
+#elif defined (USE_STM3210C_EVAL)
+  #define USB_DISCONNECT                      0  
+  #define USB_DISCONNECT_PIN                  0
+  #define RCC_APB2Periph_GPIO_DISCONNECT      0
+  #define EVAL_COM1_IRQHandler                USART2_IRQHandler 
+
+#elif defined (USE_STM32L152_EVAL) || defined (USE_STM32L152D_EVAL)
+ /* 
+   For STM32L15xx devices it is possible to use the internal USB pullup
+   controlled by register SYSCFG_PMC (refer to RM0038 reference manual for
+   more details).
+   It is also possible to use external pullup (and disable the internal pullup)
+   by setting the define USB_USE_EXTERNAL_PULLUP in file platform_config.h
+   and configuring the right pin to be used for the external pull up configuration.
+   To have more details on how to use an external pull up, please refer to 
+   STM3210E-EVAL evaluation board manuals.
+   */
+ /* Uncomment the following define to use an external pull up instead of the 
+    integrated STM32L15xx internal pull up. In this case make sure to set up
+    correctly the external required hardware and the GPIO defines below.*/
+/* #define USB_USE_EXTERNAL_PULLUP */
+
+ #if !defined(USB_USE_EXTERNAL_PULLUP)
+  #define STM32L15_USB_CONNECT                SYSCFG_USBPuCmd(ENABLE)
+  #define STM32L15_USB_DISCONNECT             SYSCFG_USBPuCmd(DISABLE)
+
+ #elif defined(USB_USE_EXTERNAL_PULLUP)
+  /* PA0 is chosen just as illustrating example, you should modify the defines
+    below according to your hardware configuration. */ 
+  #define USB_DISCONNECT                      GPIOA
+  #define USB_DISCONNECT_PIN                  GPIO_PIN_0
+  #define RCC_AHBPeriph_GPIO_DISCONNECT       RCC_AHBPeriph_GPIOA
+  #define STM32L15_USB_CONNECT                GPIO_ResetBits(USB_DISCONNECT, USB_DISCONNECT_PIN)
+  #define STM32L15_USB_DISCONNECT             GPIO_SetBits(USB_DISCONNECT, USB_DISCONNECT_PIN)
+ #endif /* USB_USE_EXTERNAL_PULLUP */
+
+#ifdef USE_STM32L152_EVAL 
+ #define EVAL_COM1_IRQHandler              USART2_IRQHandler
+#elif defined (USE_STM32L152D_EVAL) 
+ #define EVAL_COM1_IRQHandler              USART1_IRQHandler
+#endif /*USE_STM32L152_EVAL*/
+
+#endif /* USE_STM3210B_EVAL */
+
+/* Exported macro ------------------------------------------------------------*/
+/* Exported functions ------------------------------------------------------- */
+
+#endif /* __STM32L_SPIRIT1_CONFIG_H */
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/