Revision 1:37f2341e763b, committed 2010-06-16

Comitter:

tyger23

Date:

Wed Jun 16 16:08:29 2010 +0000

Parent:

0:e05fd3c9c4b3

Commit message:

Changed in this revision

--- a/main.cpp	Tue Jun 15 20:21:07 2010 +0000
+++ b/main.cpp	Wed Jun 16 16:08:29 2010 +0000
@@ -8,16 +8,15 @@
 #include "EAOLED.h"
 #include "SDFileSystem.h"
 
-SDFileSystem sd(p5, p6, p7, p24, "sd"); //Used for file system writes to the EA SD card.  Comment this out if displaying on OLED.
+SDFileSystem sd(p5, p6, p7, p24, "sd"); //Used for file system writes to the EA SD card.  Comment this out if displaying on OLED. Make sure J55 pins 1&2 (A) are disconnected!
 DigitalOut myled1(LED1);
 DigitalOut myled2(LED2);
 DigitalOut myled3(LED3);
 //EAOLED oled(p5, p6, p7, p8, p25); // mosi, dnc, sclk, cs, power ***this is only used if displaying temp on OLED instead of file writing***
 InterruptIn sense(p8); //make sure EA board J25 is set to PIO0_2  ***if using the OLED, must change this to pin 10 and connect wire from J25 center pin to pin10 on mBed, make sure J25 does not have a jumper populated***
 
-Timer timer; //timer used for keeping track of elapesd time
 Timeout timeout; //timeout used for calculation of frequency
-int edgecount, on, seconds;
+int edgecount, on, et;
 float temp, freq, tempf;
 
 void edge(){
@@ -35,18 +34,22 @@
 //    oled.locate(0,2); //*** make sure this is not commented out if using the OLED
 //    oled.printf("Temperature:"); //*** make sure this is not commented out if using the OLED
     myled1 = 1; //indicates the program is running
-    timer.start(); //starts the tracking timer.  Can comment this out if using the OLED.
     FILE *fp = fopen("/sd/temperat.csv", "w"); //formats the file header. Comment this out if using the OLED.
     fprintf(fp,"Time, Freq, TempC, TempF\n"); //Comment this out if using the OLED
     fclose(fp); //Comment this out if using the OLED
+    et = 0; //Sets elapsed time to 0.  Can comment this out if using OLED.
     
     while(1){
+        myled2 = 0; //indicates temperature is not being monitored.  Can be commented out if using OLED.
+        myled3 = 1; //indicates safe to remove power or SD card.  Can be commented out if using OLED.
+        wait(1); //wait time to allow for safe card removal or powerdown.  Can be commented out if using OLED.
+        myled2 = 1; //indicates the temperature is being monitored.  Can be commented out if using OLED.
+        myled3 = 0; //indicates not safe to remove SD card or power.  Can be commented out if using OLED.
+
+        FILE *fp = fopen("/sd/temperat.csv", "a"); //comment this out if using the OLED
+
         on=1;
         edgecount = 0;
-        myled2 = 1; //indicates the temperature is being monitored
-        myled3 = 0;
-        FILE *fp = fopen("/sd/temperat.csv", "a"); //comment this out if using the OLED
-
         timeout.attach(&attimeout, 5); //sets the amount of time used to calcuate the frequency of the temp sensor
         while(on){
             sense.rise(&edge); //tracks the rising edge of the temp sensor
@@ -66,12 +69,8 @@
         tempf = tempf + 32; //calcualtes the temperature in degrees F
 //        oled.locate(0,4); //*** make sure this is not commented out if using the OLED
 //        oled.printf("%2.3f", tempf); //*** make sure this is not commented out if using the OLED
-        seconds = timer.read(); //Reads the elaped time
-        fprintf(fp, "%d, ", seconds); //Comment this out if using the OLED
-        fprintf(fp,"%4.3f, %2.3f, %2.3f\n", freq, temp, tempf); //Comment this out if using the OLED
+        et = et+6; //Calculates the elaped time in seconds. If changing the timeout or the wait time for SD safe removal, you must change this accordingly. Comment this out if using the OLED
+        fprintf(fp,"%d, %4.3f, %2.3f, %2.3f\n", et, freq, temp, tempf); //Comment this out if using the OLED
         fclose(fp); //Comment this out if using the OLED
-        myled2 = 0; //indicates temperature monitoring is over
-        myled3 = 1; //indicates safe to remove power or SD card
-        wait(1); //wait time to allow for safe card removal or powerdown.  Can be commented out if using OLED.
     }
 }