Diff: tft_interface/cy8ckit_028_tft.cpp

Revision:

0:4ad2c16b6e43

Child:

1:cf461b359823

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/tft_interface/cy8ckit_028_tft.cpp	Fri Aug 09 23:18:24 2019 +0000
@@ -0,0 +1,358 @@
+/***************************************************************************//**
+* \file DisplayInterface.h
+* \version 1.0
+*
+* \brief
+* Objective:
+*    This is display software i8080 interface source file
+*
+********************************************************************************
+* \copyright
+* Copyright 2018-2019 Cypress Semiconductor Corporation
+* SPDX-License-Identifier: Apache-2.0
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+*     http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*******************************************************************************/
+
+
+#include "cy8ckit_028_tft.h"
+#include <mbed_wait_api.h>
+
+
+/*******************************************************************************
+* Function Name: DataWrite
+****************************************************************************//**
+*
+* \brief
+*   Writes one byte of data to the software i8080 interface.
+*
+* \details
+*   This function:
+*       - Writes data to the data bus
+*       - Sends low pulse to the LCD_NWR line to write data
+* 
+* \todo
+*   All this should be replaced with a udb register to save all the shifting
+*   and individual bit writing.
+*
+*******************************************************************************/
+void DataWrite(U8 data)
+{
+    LCD_REG0 = (data & 0x01);
+    LCD_REG1 = ((data>>1) & 0x01);
+    LCD_REG2 = ((data>>2) & 0x01);
+    LCD_REG3 = ((data>>3) & 0x01);
+    LCD_REG4 = ((data>>4) & 0x01);
+    LCD_REG5 = ((data>>5) & 0x01);
+    LCD_REG6 = ((data>>6) & 0x01);
+    LCD_REG7 = ((data>>7) & 0x01);
+    
+    LCD_NWR = 0u;
+    LCD_NWR = 1u;
+
+}
+
+
+/*******************************************************************************
+* Function Name: DataRead
+****************************************************************************//**
+*
+* \brief
+*   Reads one byte of data from the software i8080 interface.
+*
+* \details
+*   This function:
+*       - Changes data bus GPIO pins drive mode to digital Hi-Z with enabled input 
+*         buffer
+*       - Sends low pulse to LCD_NRD line to read data
+*       - Reads data from the data bus
+*       - Sends low pulse to the LCD_NWR line to write data
+*       - Changes data bus GPIO pins drive mode back to to Strong Drive mode
+* 
+* \todo
+*   All this should be replaced with a udb register to save all the shifting
+*   and individual bit reading.
+*
+*******************************************************************************/
+U8 DataRead(void)
+{
+    U8 data = 0u;
+
+    /* enable input */
+    LCD_REG0.input();
+    LCD_REG1.input();
+    LCD_REG2.input();
+    LCD_REG3.input();
+    LCD_REG4.input();
+    LCD_REG5.input();
+    LCD_REG6.input();
+    LCD_REG7.input();
+
+    LCD_NRD = 0u;  //  Pulse read line low then read the data port
+    
+    data = (U8)LCD_REG0.read();
+    data |= (U8)LCD_REG1.read()<<1;
+    data |= (U8)LCD_REG2.read()<<2;
+    data |= (U8)LCD_REG3.read()<<3;
+    data |= (U8)LCD_REG4.read()<<4;
+    data |= (U8)LCD_REG5.read()<<5;
+    data |= (U8)LCD_REG6.read()<<6;
+    data |= (U8)LCD_REG7.read()<<7;
+    
+    LCD_NRD = 1u;  // Raise the read line and then go back to output port
+       
+    LCD_REG0.output();
+    LCD_REG1.output();
+    LCD_REG2.output();
+    LCD_REG3.output();
+    LCD_REG4.output();
+    LCD_REG5.output();
+    LCD_REG6.output();
+    LCD_REG7.output();
+
+    return data;
+}
+
+
+/*******************************************************************************
+* Function Name: DisplayIntf_Init
+****************************************************************************//**
+*
+* \brief
+*   Initializes software i8080 interface.
+*
+* \details
+*   This function:
+*       - Initializes interface GPIO pins
+*
+*******************************************************************************/
+void DisplayIntf_Init(void)
+{
+    /* All pins are initialized by the Device Configurator. */
+    LCD_RESET = 1u;
+    LCD_NRD = 1u;
+    LCD_NWR = 1u;
+    LCD_DC = 0u;
+    LCD_REG0.output();
+    LCD_REG1.output();
+    LCD_REG2.output();
+    LCD_REG3.output();
+    LCD_REG4.output();
+    LCD_REG5.output();
+    LCD_REG6.output();
+    LCD_REG7.output();
+    wait_ms(20);
+    LCD_RESET = 0u;
+    wait_ms(100);
+    
+    LCD_RESET = 1u;
+    wait_ms(100);
+
+    DisplayIntf_Write8_A0(0x28);
+    DisplayIntf_Write8_A0(0x11);    /* Exit Sleep mode */
+    wait_ms(100);
+    DisplayIntf_Write8_A0(0x36);
+    DisplayIntf_Write8_A1(0xA0);    /* MADCTL: memory data access control */
+    DisplayIntf_Write8_A0(0x3A);
+    DisplayIntf_Write8_A1(0x65);    /* COLMOD: Interface Pixel format */
+    DisplayIntf_Write8_A0(0xB2);
+    DisplayIntf_Write8_A1(0x0C);
+    DisplayIntf_Write8_A1(0x0C);
+    DisplayIntf_Write8_A1(0x00);
+    DisplayIntf_Write8_A1(0x33);
+    DisplayIntf_Write8_A1(0x33);    /* PORCTRK: Porch setting */
+    DisplayIntf_Write8_A0(0xB7);
+    DisplayIntf_Write8_A1(0x35);    /* GCTRL: Gate Control */
+    DisplayIntf_Write8_A0(0xBB);
+    DisplayIntf_Write8_A1(0x2B);    /* VCOMS: VCOM setting */
+    DisplayIntf_Write8_A0(0xC0);
+    DisplayIntf_Write8_A1(0x2C);    /* LCMCTRL: LCM Control */
+    DisplayIntf_Write8_A0(0xC2);
+    DisplayIntf_Write8_A1(0x01);
+    DisplayIntf_Write8_A1(0xFF);    /* VDVVRHEN: VDV and VRH Command Enable */
+    DisplayIntf_Write8_A0(0xC3);
+    DisplayIntf_Write8_A1(0x11);    /* VRHS: VRH Set */
+    DisplayIntf_Write8_A0(0xC4);
+    DisplayIntf_Write8_A1(0x20);    /* VDVS: VDV Set */
+    DisplayIntf_Write8_A0(0xC6);
+    DisplayIntf_Write8_A1(0x0F);    /* FRCTRL2: Frame Rate control in normal mode */
+    DisplayIntf_Write8_A0(0xD0);
+    DisplayIntf_Write8_A1(0xA4);
+    DisplayIntf_Write8_A1(0xA1);    /* PWCTRL1: Power Control 1 */
+    DisplayIntf_Write8_A0(0xE0);
+    DisplayIntf_Write8_A1(0xD0);
+    DisplayIntf_Write8_A1(0x00);
+    DisplayIntf_Write8_A1(0x05);
+    DisplayIntf_Write8_A1(0x0E);
+    DisplayIntf_Write8_A1(0x15);
+    DisplayIntf_Write8_A1(0x0D);
+    DisplayIntf_Write8_A1(0x37);
+    DisplayIntf_Write8_A1(0x43);
+    DisplayIntf_Write8_A1(0x47);
+    DisplayIntf_Write8_A1(0x09);
+    DisplayIntf_Write8_A1(0x15);
+    DisplayIntf_Write8_A1(0x12);
+    DisplayIntf_Write8_A1(0x16);
+    DisplayIntf_Write8_A1(0x19);    /* PVGAMCTRL: Positive Voltage Gamma control */
+    DisplayIntf_Write8_A0(0xE1);
+    DisplayIntf_Write8_A1(0xD0);
+    DisplayIntf_Write8_A1(0x00);
+    DisplayIntf_Write8_A1(0x05);
+    DisplayIntf_Write8_A1(0x0D);
+    DisplayIntf_Write8_A1(0x0C);
+    DisplayIntf_Write8_A1(0x06);
+    DisplayIntf_Write8_A1(0x2D);
+    DisplayIntf_Write8_A1(0x44);
+    DisplayIntf_Write8_A1(0x40);
+    DisplayIntf_Write8_A1(0x0E);
+    DisplayIntf_Write8_A1(0x1C);
+    DisplayIntf_Write8_A1(0x18);
+    DisplayIntf_Write8_A1(0x16);
+    DisplayIntf_Write8_A1(0x19);    /* NVGAMCTRL: Negative Voltage Gamma control */
+    DisplayIntf_Write8_A0(0x2B);
+    DisplayIntf_Write8_A1(0x00);
+    DisplayIntf_Write8_A1(0x00);
+    DisplayIntf_Write8_A1(0x00);
+    DisplayIntf_Write8_A1(0xEF);    /* Y address set */
+    DisplayIntf_Write8_A0(0x2A);
+    DisplayIntf_Write8_A1(0x00);
+    DisplayIntf_Write8_A1(0x00);
+    DisplayIntf_Write8_A1(0x01);
+    DisplayIntf_Write8_A1(0x3F);    /* X address set */
+    wait_ms(10);
+    DisplayIntf_Write8_A0(0x29);
+
+
+}
+
+
+/*******************************************************************************
+* Function Name: DisplayIntf_Write8_A0
+****************************************************************************//**
+*
+* \brief
+*   Writes one byte of data to the software i8080 interface with the LCD_DC pin 
+*   set to 0
+*
+* \details
+*   This function:
+*       - Sets LCD_DC pin to 0
+*       - Writes one data byte
+*
+*******************************************************************************/
+void DisplayIntf_Write8_A0(U8 data)
+{
+    LCD_DC = 0u;
+    DataWrite(data);
+}
+
+
+/*******************************************************************************
+* Function Name: DisplayIntf_Write8_A1
+****************************************************************************//**
+*
+* \brief
+*   Writes one byte of data to the software i8080 interface with the LCD_DC pin 
+*   set to 1
+*
+* \details
+*   This function:
+*       - Sets LCD_DC pin to 1
+*       - Writes one data byte
+*
+*******************************************************************************/
+void DisplayIntf_Write8_A1(U8 data)
+{
+    LCD_DC = 1u;
+    DataWrite(data);
+}
+
+
+/*******************************************************************************
+* Function Name: DisplayIntf_WriteM8_A1
+****************************************************************************//**
+*
+* \brief
+*   Writes multiple bytes of data to the software i8080 interface with the LCD_DC 
+*   pin set to 1
+*
+* \details
+*   This function:
+*       - Sets LCD_DC pin to 1
+*       - Writes data bytes
+*
+*******************************************************************************/
+void DisplayIntf_WriteM8_A1(U8 data[], int num)
+{
+    int i = 0;
+
+    LCD_DC = 1u;
+
+    for(i = 0; i < num; i++)
+    {
+        DataWrite(data[i]);
+    }
+}
+
+
+/*******************************************************************************
+* Function Name: DisplayIntf_Read8_A1
+****************************************************************************//**
+*
+* \brief
+*   Reads one byte of data from the software i8080 interface with the LCD_DC pin 
+*   set to 1
+*
+* \details
+*   This function:
+*       - Sets LCD_DC pin to 1
+*       - Reads one data byte
+*
+*******************************************************************************/
+U8 DisplayIntf_Read8_A1(void)
+{
+    LCD_DC = 1u;
+    return DataRead();
+}
+
+
+/*******************************************************************************
+* Function Name: DisplayIntf_ReadM8_A1
+****************************************************************************//**
+*
+* \brief
+*   Reads multiple bytes of data from the software i8080 interface with the LCD_DC 
+*   pin set to 1
+*
+* \details
+*   This function:
+*       - Sets LCD_DC pin to 1
+*       - Reads data bytes
+*
+*******************************************************************************/
+void DisplayIntf_ReadM8_A1(U8 data[], int num)
+{
+    int i = 0;
+
+    LCD_DC = 1u;
+
+    for(i = 0; i < num; i++)
+    {
+        data[i] = DataRead();
+    }
+}
+
+
+/* [] END OF FILE */
+
+