Only encoders configured.
Dependencies: mbed-rtos mbed ros_lib_indigo
stm32f7xx_hal_conf.h
00001 /** 00002 ****************************************************************************** 00003 * @file stm32f7xx_hal_conf.h 00004 * @brief HAL configuration file. 00005 ****************************************************************************** 00006 * @attention 00007 * 00008 * <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2> 00009 * 00010 * Redistribution and use in source and binary forms, with or without modification, 00011 * are permitted provided that the following conditions are met: 00012 * 1. Redistributions of source code must retain the above copyright notice, 00013 * this list of conditions and the following disclaimer. 00014 * 2. Redistributions in binary form must reproduce the above copyright notice, 00015 * this list of conditions and the following disclaimer in the documentation 00016 * and/or other materials provided with the distribution. 00017 * 3. Neither the name of STMicroelectronics nor the names of its contributors 00018 * may be used to endorse or promote products derived from this software 00019 * without specific prior written permission. 00020 * 00021 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" 00022 * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE 00023 * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE 00024 * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE 00025 * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL 00026 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR 00027 * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER 00028 * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, 00029 * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE 00030 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. 00031 * 00032 ****************************************************************************** 00033 */ 00034 00035 /* Define to prevent recursive inclusion -------------------------------------*/ 00036 #ifndef __STM32F7xx_HAL_CONF_H 00037 #define __STM32F7xx_HAL_CONF_H 00038 00039 #ifdef __cplusplus 00040 extern "C" { 00041 #endif 00042 00043 #include "main.h" 00044 /* Exported types ------------------------------------------------------------*/ 00045 /* Exported constants --------------------------------------------------------*/ 00046 00047 /* ########################## Module Selection ############################## */ 00048 /** 00049 * @brief This is the list of modules to be used in the HAL driver 00050 */ 00051 #define HAL_MODULE_ENABLED 00052 00053 /* #define HAL_ADC_MODULE_ENABLED */ 00054 /* #define HAL_CAN_MODULE_ENABLED */ 00055 /* #define HAL_CEC_MODULE_ENABLED */ 00056 /* #define HAL_CRC_MODULE_ENABLED */ 00057 /* #define HAL_CRYP_MODULE_ENABLED */ 00058 /* #define HAL_DAC_MODULE_ENABLED */ 00059 /* #define HAL_DCMI_MODULE_ENABLED */ 00060 /* #define HAL_DMA2D_MODULE_ENABLED */ 00061 /* #define HAL_ETH_MODULE_ENABLED */ 00062 /* #define HAL_NAND_MODULE_ENABLED */ 00063 /* #define HAL_NOR_MODULE_ENABLED */ 00064 /* #define HAL_SRAM_MODULE_ENABLED */ 00065 /* #define HAL_SDRAM_MODULE_ENABLED */ 00066 /* #define HAL_HASH_MODULE_ENABLED */ 00067 /* #define HAL_I2S_MODULE_ENABLED */ 00068 /* #define HAL_IWDG_MODULE_ENABLED */ 00069 /* #define HAL_LPTIM_MODULE_ENABLED */ 00070 /* #define HAL_LTDC_MODULE_ENABLED */ 00071 /* #define HAL_QSPI_MODULE_ENABLED */ 00072 /* #define HAL_RNG_MODULE_ENABLED */ 00073 /* #define HAL_RTC_MODULE_ENABLED */ 00074 /* #define HAL_SAI_MODULE_ENABLED */ 00075 /* #define HAL_SD_MODULE_ENABLED */ 00076 /* #define HAL_SPDIFRX_MODULE_ENABLED */ 00077 /* #define HAL_SPI_MODULE_ENABLED */ 00078 #define HAL_TIM_MODULE_ENABLED 00079 /* #define HAL_UART_MODULE_ENABLED */ 00080 /* #define HAL_USART_MODULE_ENABLED */ 00081 /* #define HAL_IRDA_MODULE_ENABLED */ 00082 /* #define HAL_SMARTCARD_MODULE_ENABLED */ 00083 /* #define HAL_WWDG_MODULE_ENABLED */ 00084 /* #define HAL_PCD_MODULE_ENABLED */ 00085 /* #define HAL_HCD_MODULE_ENABLED */ 00086 /* #define HAL_DFSDM_MODULE_ENABLED */ 00087 /* #define HAL_DSI_MODULE_ENABLED */ 00088 /* #define HAL_JPEG_MODULE_ENABLED */ 00089 /* #define HAL_MDIOS_MODULE_ENABLED */ 00090 #define HAL_GPIO_MODULE_ENABLED 00091 #define HAL_DMA_MODULE_ENABLED 00092 #define HAL_RCC_MODULE_ENABLED 00093 #define HAL_FLASH_MODULE_ENABLED 00094 #define HAL_PWR_MODULE_ENABLED 00095 #define HAL_I2C_MODULE_ENABLED 00096 #define HAL_CORTEX_MODULE_ENABLED 00097 00098 /* ########################## HSE/HSI Values adaptation ##################### */ 00099 /** 00100 * @brief Adjust the value of External High Speed oscillator (HSE) used in your application. 00101 * This value is used by the RCC HAL module to compute the system frequency 00102 * (when HSE is used as system clock source, directly or through the PLL). 00103 */ 00104 #if !defined (HSE_VALUE) 00105 #define HSE_VALUE ((uint32_t)16000000U) /*!< Value of the External oscillator in Hz */ 00106 #endif /* HSE_VALUE */ 00107 00108 #if !defined (HSE_STARTUP_TIMEOUT) 00109 #define HSE_STARTUP_TIMEOUT ((uint32_t)100U) /*!< Time out for HSE start up, in ms */ 00110 #endif /* HSE_STARTUP_TIMEOUT */ 00111 00112 /** 00113 * @brief Internal High Speed oscillator (HSI) value. 00114 * This value is used by the RCC HAL module to compute the system frequency 00115 * (when HSI is used as system clock source, directly or through the PLL). 00116 */ 00117 #if !defined (HSI_VALUE) 00118 #define HSI_VALUE ((uint32_t)16000000U) /*!< Value of the Internal oscillator in Hz*/ 00119 #endif /* HSI_VALUE */ 00120 00121 /** 00122 * @brief Internal Low Speed oscillator (LSI) value. 00123 */ 00124 #if !defined (LSI_VALUE) 00125 #define LSI_VALUE ((uint32_t)32000U) /*!< LSI Typical Value in Hz*/ 00126 #endif /* LSI_VALUE */ /*!< Value of the Internal Low Speed oscillator in Hz 00127 The real value may vary depending on the variations 00128 in voltage and temperature. */ 00129 /** 00130 * @brief External Low Speed oscillator (LSE) value. 00131 */ 00132 #if !defined (LSE_VALUE) 00133 #define LSE_VALUE ((uint32_t)32768U) /*!< Value of the External Low Speed oscillator in Hz */ 00134 #endif /* LSE_VALUE */ 00135 00136 #if !defined (LSE_STARTUP_TIMEOUT) 00137 #define LSE_STARTUP_TIMEOUT ((uint32_t)5000U) /*!< Time out for LSE start up, in ms */ 00138 #endif /* LSE_STARTUP_TIMEOUT */ 00139 00140 /** 00141 * @brief External clock source for I2S peripheral 00142 * This value is used by the I2S HAL module to compute the I2S clock source 00143 * frequency, this source is inserted directly through I2S_CKIN pad. 00144 */ 00145 #if !defined (EXTERNAL_CLOCK_VALUE) 00146 #define EXTERNAL_CLOCK_VALUE ((uint32_t)12288000U) /*!< Value of the Internal oscillator in Hz*/ 00147 #endif /* EXTERNAL_CLOCK_VALUE */ 00148 00149 /* Tip: To avoid modifying this file each time you need to use different HSE, 00150 === you can define the HSE value in your toolchain compiler preprocessor. */ 00151 00152 /* ########################### System Configuration ######################### */ 00153 /** 00154 * @brief This is the HAL system configuration section 00155 */ 00156 #define VDD_VALUE ((uint32_t)3300U) /*!< Value of VDD in mv */ 00157 #define TICK_INT_PRIORITY ((uint32_t)0U) /*!< tick interrupt priority */ 00158 #define USE_RTOS 0U 00159 #define PREFETCH_ENABLE 0U 00160 #define ART_ACCLERATOR_ENABLE 0U /* To enable instruction cache and prefetch */ 00161 00162 /* ########################## Assert Selection ############################## */ 00163 /** 00164 * @brief Uncomment the line below to expanse the "assert_param" macro in the 00165 * HAL drivers code 00166 */ 00167 /* #define USE_FULL_ASSERT 1 */ 00168 00169 /* ################## Ethernet peripheral configuration ##################### */ 00170 00171 /* Section 1 : Ethernet peripheral configuration */ 00172 00173 /* MAC ADDRESS: MAC_ADDR0:MAC_ADDR1:MAC_ADDR2:MAC_ADDR3:MAC_ADDR4:MAC_ADDR5 */ 00174 #define MAC_ADDR0 2U 00175 #define MAC_ADDR1 0U 00176 #define MAC_ADDR2 0U 00177 #define MAC_ADDR3 0U 00178 #define MAC_ADDR4 0U 00179 #define MAC_ADDR5 0U 00180 00181 /* Definition of the Ethernet driver buffers size and count */ 00182 #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for receive */ 00183 #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */ 00184 #define ETH_RXBUFNB ((uint32_t)4U) /* 4 Rx buffers of size ETH_RX_BUF_SIZE */ 00185 #define ETH_TXBUFNB ((uint32_t)4U) /* 4 Tx buffers of size ETH_TX_BUF_SIZE */ 00186 00187 /* Section 2: PHY configuration section */ 00188 00189 /* DP83848_PHY_ADDRESS Address*/ 00190 #define DP83848_PHY_ADDRESS 0x01U 00191 /* PHY Reset delay these values are based on a 1 ms Systick interrupt*/ 00192 #define PHY_RESET_DELAY ((uint32_t)0x000000FFU) 00193 /* PHY Configuration delay */ 00194 #define PHY_CONFIG_DELAY ((uint32_t)0x00000FFFU) 00195 00196 #define PHY_READ_TO ((uint32_t)0x0000FFFFU) 00197 #define PHY_WRITE_TO ((uint32_t)0x0000FFFFU) 00198 00199 /* Section 3: Common PHY Registers */ 00200 00201 #define PHY_BCR ((uint16_t)0x0000U) /*!< Transceiver Basic Control Register */ 00202 #define PHY_BSR ((uint16_t)0x0001U) /*!< Transceiver Basic Status Register */ 00203 00204 #define PHY_RESET ((uint16_t)0x8000U) /*!< PHY Reset */ 00205 #define PHY_LOOPBACK ((uint16_t)0x4000U) /*!< Select loop-back mode */ 00206 #define PHY_FULLDUPLEX_100M ((uint16_t)0x2100U) /*!< Set the full-duplex mode at 100 Mb/s */ 00207 #define PHY_HALFDUPLEX_100M ((uint16_t)0x2000U) /*!< Set the half-duplex mode at 100 Mb/s */ 00208 #define PHY_FULLDUPLEX_10M ((uint16_t)0x0100U) /*!< Set the full-duplex mode at 10 Mb/s */ 00209 #define PHY_HALFDUPLEX_10M ((uint16_t)0x0000U) /*!< Set the half-duplex mode at 10 Mb/s */ 00210 #define PHY_AUTONEGOTIATION ((uint16_t)0x1000U) /*!< Enable auto-negotiation function */ 00211 #define PHY_RESTART_AUTONEGOTIATION ((uint16_t)0x0200U) /*!< Restart auto-negotiation function */ 00212 #define PHY_POWERDOWN ((uint16_t)0x0800U) /*!< Select the power down mode */ 00213 #define PHY_ISOLATE ((uint16_t)0x0400U) /*!< Isolate PHY from MII */ 00214 00215 #define PHY_AUTONEGO_COMPLETE ((uint16_t)0x0020U) /*!< Auto-Negotiation process completed */ 00216 #define PHY_LINKED_STATUS ((uint16_t)0x0004U) /*!< Valid link established */ 00217 #define PHY_JABBER_DETECTION ((uint16_t)0x0002U) /*!< Jabber condition detected */ 00218 00219 /* Section 4: Extended PHY Registers */ 00220 #define PHY_SR ((uint16_t)0x10U) /*!< PHY status register Offset */ 00221 00222 #define PHY_SPEED_STATUS ((uint16_t)0x0002U) /*!< PHY Speed mask */ 00223 #define PHY_DUPLEX_STATUS ((uint16_t)0x0004U) /*!< PHY Duplex mask */ 00224 00225 /* ################## SPI peripheral configuration ########################## */ 00226 00227 /* CRC FEATURE: Use to activate CRC feature inside HAL SPI Driver 00228 * Activated: CRC code is present inside driver 00229 * Deactivated: CRC code cleaned from driver 00230 */ 00231 00232 #define USE_SPI_CRC 0U 00233 00234 /* Includes ------------------------------------------------------------------*/ 00235 /** 00236 * @brief Include module's header file 00237 */ 00238 00239 #ifdef HAL_RCC_MODULE_ENABLED 00240 #include "stm32f7xx_hal_rcc.h" 00241 #endif /* HAL_RCC_MODULE_ENABLED */ 00242 00243 #ifdef HAL_GPIO_MODULE_ENABLED 00244 #include "stm32f7xx_hal_gpio.h" 00245 #endif /* HAL_GPIO_MODULE_ENABLED */ 00246 00247 #ifdef HAL_DMA_MODULE_ENABLED 00248 #include "stm32f7xx_hal_dma.h" 00249 #endif /* HAL_DMA_MODULE_ENABLED */ 00250 00251 #ifdef HAL_CORTEX_MODULE_ENABLED 00252 #include "stm32f7xx_hal_cortex.h" 00253 #endif /* HAL_CORTEX_MODULE_ENABLED */ 00254 00255 #ifdef HAL_ADC_MODULE_ENABLED 00256 #include "stm32f7xx_hal_adc.h" 00257 #endif /* HAL_ADC_MODULE_ENABLED */ 00258 00259 #ifdef HAL_CAN_MODULE_ENABLED 00260 #include "stm32f7xx_hal_can.h" 00261 #endif /* HAL_CAN_MODULE_ENABLED */ 00262 00263 #ifdef HAL_CEC_MODULE_ENABLED 00264 #include "stm32f7xx_hal_cec.h" 00265 #endif /* HAL_CEC_MODULE_ENABLED */ 00266 00267 #ifdef HAL_CRC_MODULE_ENABLED 00268 #include "stm32f7xx_hal_crc.h" 00269 #endif /* HAL_CRC_MODULE_ENABLED */ 00270 00271 #ifdef HAL_CRYP_MODULE_ENABLED 00272 #include "stm32f7xx_hal_cryp.h" 00273 #endif /* HAL_CRYP_MODULE_ENABLED */ 00274 00275 #ifdef HAL_DMA2D_MODULE_ENABLED 00276 #include "stm32f7xx_hal_dma2d.h" 00277 #endif /* HAL_DMA2D_MODULE_ENABLED */ 00278 00279 #ifdef HAL_DAC_MODULE_ENABLED 00280 #include "stm32f7xx_hal_dac.h" 00281 #endif /* HAL_DAC_MODULE_ENABLED */ 00282 00283 #ifdef HAL_DCMI_MODULE_ENABLED 00284 #include "stm32f7xx_hal_dcmi.h" 00285 #endif /* HAL_DCMI_MODULE_ENABLED */ 00286 00287 #ifdef HAL_ETH_MODULE_ENABLED 00288 #include "stm32f7xx_hal_eth.h" 00289 #endif /* HAL_ETH_MODULE_ENABLED */ 00290 00291 #ifdef HAL_FLASH_MODULE_ENABLED 00292 #include "stm32f7xx_hal_flash.h" 00293 #endif /* HAL_FLASH_MODULE_ENABLED */ 00294 00295 #ifdef HAL_SRAM_MODULE_ENABLED 00296 #include "stm32f7xx_hal_sram.h" 00297 #endif /* HAL_SRAM_MODULE_ENABLED */ 00298 00299 #ifdef HAL_NOR_MODULE_ENABLED 00300 #include "stm32f7xx_hal_nor.h" 00301 #endif /* HAL_NOR_MODULE_ENABLED */ 00302 00303 #ifdef HAL_NAND_MODULE_ENABLED 00304 #include "stm32f7xx_hal_nand.h" 00305 #endif /* HAL_NAND_MODULE_ENABLED */ 00306 00307 #ifdef HAL_SDRAM_MODULE_ENABLED 00308 #include "stm32f7xx_hal_sdram.h" 00309 #endif /* HAL_SDRAM_MODULE_ENABLED */ 00310 00311 #ifdef HAL_HASH_MODULE_ENABLED 00312 #include "stm32f7xx_hal_hash.h" 00313 #endif /* HAL_HASH_MODULE_ENABLED */ 00314 00315 #ifdef HAL_I2C_MODULE_ENABLED 00316 #include "stm32f7xx_hal_i2c.h" 00317 #endif /* HAL_I2C_MODULE_ENABLED */ 00318 00319 #ifdef HAL_I2S_MODULE_ENABLED 00320 #include "stm32f7xx_hal_i2s.h" 00321 #endif /* HAL_I2S_MODULE_ENABLED */ 00322 00323 #ifdef HAL_IWDG_MODULE_ENABLED 00324 #include "stm32f7xx_hal_iwdg.h" 00325 #endif /* HAL_IWDG_MODULE_ENABLED */ 00326 00327 #ifdef HAL_LPTIM_MODULE_ENABLED 00328 #include "stm32f7xx_hal_lptim.h" 00329 #endif /* HAL_LPTIM_MODULE_ENABLED */ 00330 00331 #ifdef HAL_LTDC_MODULE_ENABLED 00332 #include "stm32f7xx_hal_ltdc.h" 00333 #endif /* HAL_LTDC_MODULE_ENABLED */ 00334 00335 #ifdef HAL_PWR_MODULE_ENABLED 00336 #include "stm32f7xx_hal_pwr.h" 00337 #endif /* HAL_PWR_MODULE_ENABLED */ 00338 00339 #ifdef HAL_QSPI_MODULE_ENABLED 00340 #include "stm32f7xx_hal_qspi.h" 00341 #endif /* HAL_QSPI_MODULE_ENABLED */ 00342 00343 #ifdef HAL_RNG_MODULE_ENABLED 00344 #include "stm32f7xx_hal_rng.h" 00345 #endif /* HAL_RNG_MODULE_ENABLED */ 00346 00347 #ifdef HAL_RTC_MODULE_ENABLED 00348 #include "stm32f7xx_hal_rtc.h" 00349 #endif /* HAL_RTC_MODULE_ENABLED */ 00350 00351 #ifdef HAL_SAI_MODULE_ENABLED 00352 #include "stm32f7xx_hal_sai.h" 00353 #endif /* HAL_SAI_MODULE_ENABLED */ 00354 00355 #ifdef HAL_SD_MODULE_ENABLED 00356 #include "stm32f7xx_hal_sd.h" 00357 #endif /* HAL_SD_MODULE_ENABLED */ 00358 00359 #ifdef HAL_SPDIFRX_MODULE_ENABLED 00360 #include "stm32f7xx_hal_spdifrx.h" 00361 #endif /* HAL_SPDIFRX_MODULE_ENABLED */ 00362 00363 #ifdef HAL_SPI_MODULE_ENABLED 00364 #include "stm32f7xx_hal_spi.h" 00365 #endif /* HAL_SPI_MODULE_ENABLED */ 00366 00367 #ifdef HAL_TIM_MODULE_ENABLED 00368 #include "stm32f7xx_hal_tim.h" 00369 #endif /* HAL_TIM_MODULE_ENABLED */ 00370 00371 #ifdef HAL_UART_MODULE_ENABLED 00372 #include "stm32f7xx_hal_uart.h" 00373 #endif /* HAL_UART_MODULE_ENABLED */ 00374 00375 #ifdef HAL_USART_MODULE_ENABLED 00376 #include "stm32f7xx_hal_usart.h" 00377 #endif /* HAL_USART_MODULE_ENABLED */ 00378 00379 #ifdef HAL_IRDA_MODULE_ENABLED 00380 #include "stm32f7xx_hal_irda.h" 00381 #endif /* HAL_IRDA_MODULE_ENABLED */ 00382 00383 #ifdef HAL_SMARTCARD_MODULE_ENABLED 00384 #include "stm32f7xx_hal_smartcard.h" 00385 #endif /* HAL_SMARTCARD_MODULE_ENABLED */ 00386 00387 #ifdef HAL_WWDG_MODULE_ENABLED 00388 #include "stm32f7xx_hal_wwdg.h" 00389 #endif /* HAL_WWDG_MODULE_ENABLED */ 00390 00391 #ifdef HAL_PCD_MODULE_ENABLED 00392 #include "stm32f7xx_hal_pcd.h" 00393 #endif /* HAL_PCD_MODULE_ENABLED */ 00394 00395 #ifdef HAL_HCD_MODULE_ENABLED 00396 #include "stm32f7xx_hal_hcd.h" 00397 #endif /* HAL_HCD_MODULE_ENABLED */ 00398 00399 #ifdef HAL_DFSDM_MODULE_ENABLED 00400 #include "stm32f7xx_hal_dfsdm.h" 00401 #endif /* HAL_DFSDM_MODULE_ENABLED */ 00402 00403 #ifdef HAL_DSI_MODULE_ENABLED 00404 #include "stm32f7xx_hal_dsi.h" 00405 #endif /* HAL_DSI_MODULE_ENABLED */ 00406 00407 #ifdef HAL_JPEG_MODULE_ENABLED 00408 #include "stm32f7xx_hal_jpeg.h" 00409 #endif /* HAL_JPEG_MODULE_ENABLED */ 00410 00411 #ifdef HAL_MDIOS_MODULE_ENABLED 00412 #include "stm32f7xx_hal_mdios.h" 00413 #endif /* HAL_MDIOS_MODULE_ENABLED */ 00414 /* Exported macro ------------------------------------------------------------*/ 00415 #ifdef USE_FULL_ASSERT 00416 /** 00417 * @brief The assert_param macro is used for function's parameters check. 00418 * @param expr: If expr is false, it calls assert_failed function 00419 * which reports the name of the source file and the source 00420 * line number of the call that failed. 00421 * If expr is true, it returns no value. 00422 * @retval None 00423 */ 00424 #define assert_param(expr) ((expr) ? (void)0U : assert_failed((uint8_t *)__FILE__, __LINE__)) 00425 /* Exported functions ------------------------------------------------------- */ 00426 void assert_failed(uint8_t* file, uint32_t line); 00427 #else 00428 #define assert_param(expr) ((void)0U) 00429 #endif /* USE_FULL_ASSERT */ 00430 00431 #ifdef __cplusplus 00432 } 00433 #endif 00434 00435 #endif /* __STM32F7xx_HAL_CONF_H */ 00436 00437 00438 /************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ 00439
Generated on Wed Jul 13 2022 18:23:41 by 1.7.2