Revision 29:537df716ba0b, committed 2017-04-05

Comitter:

peyo

Date:

Wed Apr 05 16:05:41 2017 +0000

Parent:

28:a31312c9756d

Commit message:

Use IKS01A1 sensors

Changed in this revision

--- a/Sensors/Temperature/HTS221.h	Wed Apr 05 08:32:05 2017 +0000
+++ /dev/null	Thu Jan 01 00:00:00 1970 +0000
@@ -1,93 +0,0 @@
-
-#ifndef HTS221_H_
-#define HTS221_H_
-
-class HTS221 {
-public:
-    HTS221(void);
-    int begin(void);
-    int activate(void);
-    int deactivate(void);
-
-    int bduActivate(void);
-    int bduDeactivate(void);
-
-    int readHumidity(void);
-    double readTemperature(void);
-private:
-    int storeCalibration(void);
-    unsigned char _h0_rH, _h1_rH;
-    unsigned int  _T0_degC, _T1_degC;
-    unsigned int  _H0_T0, _H1_T0;
-    unsigned int  _T0_OUT, _T1_OUT;
-    double _temperature;
-    int _humidity;
-    unsigned char _address;
-
-    unsigned char readRegister(unsigned char slaveAddress, unsigned char regToRead);
-    int writeRegister(unsigned char slaveAddress, unsigned char regToWrite, unsigned char dataToWrite);
-};
-
-#define HTS221_ADDRESS     0xBF
-
-//Define a few of the registers that we will be accessing on the HTS221
-#define WHO_AM_I           0x0F
-#define WHO_AM_I_RETURN    0xBC //This read-only register contains the device identifier, set to BCh
-
-#define AVERAGE_REG        0x10 // To configure humidity/temperature average.
-#define AVERAGE_DEFAULT    0x1B
-
-/*
- * [7] PD: power down control
- * (0: power-down mode; 1: active mode)
- *
- * [6:3] Reserved
- *
- * [2] BDU: block data update
- * (0: continuous update; 1: output registers not updated until MSB and LSB reading)
-The BDU bit is used to inhibit the output register update between the reading of the upper
-and lower register parts. In default mode (BDU = ?0?), the lower and upper register parts are
-updated continuously. If it is not certain whether the read will be faster than output data rate,
-it is recommended to set the BDU bit to ?1?. In this way, after the reading of the lower (upper)
-register part, the content of that output register is not updated until the upper (lower) part is
-read also.
- *
- * [1:0] ODR1, ODR0: output data rate selection (see table 17)
- */
-#define CTRL_REG1          0x20
-#define POWER_UP           0x80
-#define BDU_SET            0x4
-#define ODR0_SET           0x1   // setting sensor reading period 1Hz
-
-#define CTRL_REG2          0x21
-#define CTRL_REG3          0x22
-#define REG_DEFAULT        0x00
-
-#define STATUS_REG         0x27
-#define TEMPERATURE_READY  0x1
-#define HUMIDITY_READY     0x2
-
-#define HUMIDITY_L_REG     0x28
-#define HUMIDITY_H_REG     0x29
-#define TEMP_L_REG         0x2A
-#define TEMP_H_REG         0x2B
-/*
- * calibration registry should be read for temperature and humidity calculation.
- * Before the first calculation of temperature and humidity,
- * the master reads out the calibration coefficients.
- * will do at init phase
- */
-#define CALIB_START        0x30
-#define CALIB_END          0x3F
-/*
-#define CALIB_T0_DEGC_X8   0x32
-#define CALIB_T1_DEGC_X8   0x33
-#define CALIB_T1_T0_MSB    0x35
-#define CALIB_T0_OUT_L     0x3C
-#define CALIB_T0_OUT_H     0x3D
-#define CALIB_T1_OUT_L     0x3E
-#define CALIB_T1_OUT_H     0x3F
- */
- 
-#endif
-

--- a/Sensors/Temperature/hts221_driver.cpp	Wed Apr 05 08:32:05 2017 +0000
+++ /dev/null	Thu Jan 01 00:00:00 1970 +0000
@@ -1,250 +0,0 @@
-
-#include "HTS221.h"
-
-
-// ------------------------------------------------------------------------------
-//jmf  -- define I2C pins and functions to read & write to I2C device
-
-#include <string>
-#include "mbed.h"
-
-#include "hardware.h"
-//I2C i2c(PTC11, PTC10);    //SDA, SCL -- define the I2C pins being used. Defined in a 
-//common locatioin since sensors also use I2C
-
-// Read a single unsigned char from addressToRead and return it as a unsigned char
-unsigned char HTS221::readRegister(unsigned char slaveAddress, unsigned char ToRead)
-{
-    char data = ToRead;
-
-    i2c.write(slaveAddress, &data, 1, 1);
-    i2c.read(slaveAddress, &data, 1, 0);
-    return data;
-}
-
-// Writes a single unsigned char (dataToWrite) into regToWrite
-int HTS221::writeRegister(unsigned char slaveAddress, unsigned char regToWrite, unsigned char dataToWrite)
-{
-    const char data[] = {regToWrite, dataToWrite};
-
-    return i2c.write(slaveAddress,data,2,0);
-}
-
-
-//jmf end
-// ------------------------------------------------------------------------------
-
-//static inline int humidityReady(uint8_t data) {
-//    return (data & 0x02);
-//}
-//static inline int temperatureReady(uint8_t data) {
-//    return (data & 0x01);
-//}
-
-
-HTS221::HTS221(void) : _address(HTS221_ADDRESS)
-{
-    _temperature = 0;
-    _humidity = 0;
-}
-
-
-int HTS221::begin(void)
-{
-    uint8_t data;
-
-    data = readRegister(_address, WHO_AM_I);
-    if (data == WHO_AM_I_RETURN){
-        if (activate()){
-            storeCalibration();
-            return data;
-        }
-    }
-
-    return 0;
-}
-
-int
-HTS221::storeCalibration(void)
-{
-    uint8_t data;
-    uint16_t tmp;
-
-    for (int reg=CALIB_START; reg<=CALIB_END; reg++) {
-        if ((reg!=CALIB_START+8) && (reg!=CALIB_START+9) && (reg!=CALIB_START+4)) {
-
-            data = readRegister(HTS221_ADDRESS, reg);
-
-            switch (reg) {
-            case CALIB_START:
-                _h0_rH = data;
-                break;
-            case CALIB_START+1:
-            _h1_rH = data;
-            break;
-            case CALIB_START+2:
-            _T0_degC = data;
-            break;
-            case CALIB_START+3:
-            _T1_degC = data;
-            break;
-
-            case CALIB_START+5:
-            tmp = _T0_degC;
-            _T0_degC = (data&0x3)<<8;
-            _T0_degC |= tmp;
-
-            tmp = _T1_degC;
-            _T1_degC = ((data&0xC)>>2)<<8;
-            _T1_degC |= tmp;
-            break;
-            case CALIB_START+6:
-            _H0_T0 = data;
-            break;
-            case CALIB_START+7:
-            _H0_T0 |= data<<8;
-            break;
-            case CALIB_START+0xA:
-            _H1_T0 = data;
-            break;
-            case CALIB_START+0xB:
-            _H1_T0 |= data <<8;
-            break;
-            case CALIB_START+0xC:
-            _T0_OUT = data;
-            break;
-            case CALIB_START+0xD:
-            _T0_OUT |= data << 8;
-            break;
-            case CALIB_START+0xE:
-            _T1_OUT = data;
-            break;
-            case CALIB_START+0xF:
-            _T1_OUT |= data << 8;
-            break;
-
-
-            case CALIB_START+8:
-            case CALIB_START+9:
-            case CALIB_START+4:
-            //DO NOTHING
-            break;
-
-            // to cover any possible error
-            default:
-                return false;
-            } /* switch */
-        } /* if */
-    }  /* for */
-    return true;
-}
-
-
-int
-HTS221::activate(void)
-{
-    uint8_t data;
-
-    data = readRegister(_address, CTRL_REG1);
-    data |= POWER_UP;
-    data |= ODR0_SET;
-    writeRegister(_address, CTRL_REG1, data);
-
-    return true;
-}
-
-
-int HTS221::deactivate(void)
-{
-    uint8_t data;
-
-    data = readRegister(_address, CTRL_REG1);
-    data &= ~POWER_UP;
-    writeRegister(_address, CTRL_REG1, data);
-    return true;
-}
-
-
-int
-HTS221::bduActivate(void)
-{
-    uint8_t data;
-
-    data = readRegister(_address, CTRL_REG1);
-    data |= BDU_SET;
-    writeRegister(_address, CTRL_REG1, data);
-
-    return true;
-}
-
-
-int
-HTS221::bduDeactivate(void)
-{
-    uint8_t data;
-
-    data = readRegister(_address, CTRL_REG1);
-    data &= ~BDU_SET;
-    writeRegister(_address, CTRL_REG1, data);
-    return true;
-}
-
-
-int
-HTS221::readHumidity(void)
-{
-    uint8_t data   = 0;
-    uint16_t h_out = 0;
-    double h_temp  = 0.0;
-    double hum     = 0.0;
-
-    data = readRegister(_address, STATUS_REG);
-
-    if (data & HUMIDITY_READY) {
-        data = readRegister(_address, HUMIDITY_H_REG);
-        h_out = data << 8;  // MSB
-        data = readRegister(_address, HUMIDITY_L_REG);
-        h_out |= data;      // LSB
-
-        // Decode Humidity
-        hum = ((int16_t)(_h1_rH) - (int16_t)(_h0_rH))/2.0;  // remove x2 multiple
-
-        // Calculate humidity in decimal of grade centigrades i.e. 15.0 = 150.
-        h_temp = (((int16_t)h_out - (int16_t)_H0_T0) * hum) / ((int16_t)_H1_T0 - (int16_t)_H0_T0);
-        hum    = ((int16_t)_h0_rH) / 2.0; // remove x2 multiple
-        _humidity = (int16_t)((hum + h_temp)); // provide signed % measurement unit
-    }
-    return _humidity;
-}
-
-
-
-double
-HTS221::readTemperature(void)
-{
-    uint8_t data   = 0;
-    uint16_t t_out = 0;
-    double t_temp  = 0.0;
-    double deg     = 0.0;
-
-    data = readRegister(_address, STATUS_REG);
-
-    if (data & TEMPERATURE_READY) {
-
-        data= readRegister(_address, TEMP_H_REG);
-        t_out = data  << 8; // MSB
-        data = readRegister(_address, TEMP_L_REG);
-        t_out |= data;      // LSB
-
-        // Decode Temperature
-        deg    = ((int16_t)(_T1_degC) - (int16_t)(_T0_degC))/8.0; // remove x8 multiple
-
-        // Calculate Temperature in decimal of grade centigrades i.e. 15.0 = 150.
-        t_temp = (((int16_t)t_out - (int16_t)_T0_OUT) * deg) / ((int16_t)_T1_OUT - (int16_t)_T0_OUT);
-        deg    = ((int16_t)_T0_degC) / 8.0;     // remove x8 multiple
-        _temperature = deg + t_temp;   // provide signed celsius measurement unit
-    }
-
-    return _temperature;
-}
-

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/Sensors/X_NUCLEO_IKS01A1.lib	Wed Apr 05 16:05:41 2017 +0000
@@ -0,0 +1,1 @@
+http://developer.mbed.org/teams/ST/code/X_NUCLEO_IKS01A1/#d1c67d482bad

--- a/Sensors/hardware.h	Wed Apr 05 08:32:05 2017 +0000
+++ /dev/null	Thu Jan 01 00:00:00 1970 +0000
@@ -1,6 +0,0 @@
-#ifndef Hardware_H_
-#define Hardware_H_
-extern I2C i2c;    //SDA, SCL -- define the I2C pins being used
-
-#endif
-

--- a/main.cpp	Wed Apr 05 08:32:05 2017 +0000
+++ b/main.cpp	Wed Apr 05 16:05:41 2017 +0000
@@ -22,7 +22,7 @@
 #include "aws_iot_mqtt_interface.h"
 
 // Sensors
-#include "HTS221.h"
+#include "x_nucleo_iks01a1.h"
 
 #if DEBUG_LEVEL > 0
 #include "mbedtls/debug.h"
@@ -43,7 +43,7 @@
 
 // AWS defines
 #define PATH_MAX    1024
-#define MAX_LENGTH_OF_UPDATE_JSON_BUFFER 200 // NOTE: Be wary of this if your JSON doc grows
+#define MAX_LENGTH_OF_UPDATE_JSON_BUFFER 300 // NOTE: Be wary of this if your JSON doc grows
 #define SHADOW_SYNC_INTERVAL 3.0             // How often we sync with AWS Shadow (in seconds)
 
 // Comment out the following line if color is not supported on the terminal
@@ -96,12 +96,19 @@
 uint32_t port = AWS_IOT_MQTT_PORT;
 char iccidName[21] = "12345678901234567890";
 
+/* Instantiate the expansion board */
+static X_NUCLEO_IKS01A1 *mems_expansion_board = X_NUCLEO_IKS01A1::Instance(I2C_SDA, I2C_SCL);
+
 // Sensor data
-float temperature = 0.0;
-int   humidity    = 0;
+static HumiditySensor *humidity_sensor = mems_expansion_board->ht_sensor;
+static PressureSensor *pressure_sensor = mems_expansion_board->pt_sensor;
+static TempSensor *temp_sensor1 = mems_expansion_board->ht_sensor;
+static TempSensor *temp_sensor2 = mems_expansion_board->pt_sensor;
+float iks01a1_temperature = 0.0;
+float iks01a1_pressure = 0.0;
+float iks01a1_humidity = 0.0;
+uint8_t id;
 
-// Temp/humidity object
-HTS221 hts221; 
 
 //=====================================================================================================================
 //
@@ -119,9 +126,6 @@
 // SD card access (MOSI, MISO, SCK, CS)
 SDFileSystem sd(PTE3, PTE1, PTE2, PTE4, "sd");
 
-// I2C bus (SDA, SCL)
-I2C i2c(PTC11, PTC10);
-
 //=====================================================================================================================
 //
 // Functions
@@ -175,8 +179,10 @@
 //*********************************************************************************************************************
 void printData()
 {
-    INFO("Temperature is: %0.2f F", temperature);
-    INFO("Humidity    is: %02d", humidity);      
+    INFO("Temperature is: %0.2f C", iks01a1_temperature);
+    INFO("Humidity    is: %0.2f", iks01a1_humidity); 
+    INFO("Pressure    is: %0.2f mbar", iks01a1_pressure);      
+     
     switch (ledColor) {
          case COLOR_OFF:
              INFO("LED: Off");
@@ -382,11 +388,12 @@
             buttonOverride = false;
             
             // Get temp/humidity values
-            temperature = CTOF(hts221.readTemperature());
-            humidity = hts221.readHumidity();
+            temp_sensor1->get_temperature(&iks01a1_temperature);
+            humidity_sensor->get_humidity(&iks01a1_humidity);
+            pressure_sensor->get_pressure(&iks01a1_pressure);
     
             // Loading data into JSON format
-            sprintf(cPayload, "{\"color\":\"%s\",\"temperature\":%f,\"humidity\":%d}", colorStrings[ledColor], temperature, humidity);
+            sprintf(cPayload, "{\"color\":\"%s\",\"temperature\":%f,\"humidity\":%f,\"pressure\":%f}", colorStrings[ledColor], iks01a1_temperature, iks01a1_humidity, iks01a1_pressure);
             Msg.PayloadLen = strlen(cPayload) + 1;
             Params.MessageParams = Msg;
             
@@ -437,18 +444,24 @@
     ledController.pKey = "ledColor";
     ledController.type = SHADOW_JSON_UINT8;
 
-    // JSON struct for temperature\humidity readings
+    // JSON struct for temperature\humidity\pressure readings
     jsonStruct_t temperatureHandler;
     temperatureHandler.cb = NULL;
     temperatureHandler.pKey = "temperature";
-    temperatureHandler.pData = &temperature;
+    temperatureHandler.pData = &iks01a1_temperature;
     temperatureHandler.type = SHADOW_JSON_FLOAT;
     
     jsonStruct_t humidityHandler;
     humidityHandler.cb = NULL;
     humidityHandler.pKey = "humidity";
-    humidityHandler.pData = &humidity;
-    humidityHandler.type = SHADOW_JSON_INT16;
+    humidityHandler.pData = &iks01a1_humidity;
+    humidityHandler.type = SHADOW_JSON_FLOAT;
+    
+    jsonStruct_t pressureHandler;
+    pressureHandler.cb = NULL;
+    pressureHandler.pKey = "pressure";
+    pressureHandler.pData = &iks01a1_pressure;
+    pressureHandler.type = SHADOW_JSON_FLOAT;
     
     INFO("AWS IoT SDK Version(dev) %d.%d.%d-%s", VERSION_MAJOR, VERSION_MINOR, VERSION_PATCH, VERSION_TAG);
 
@@ -476,11 +489,10 @@
     
     // Initialize sensors
     INFO("Init sensors...");
-    //void hts221_init(void);
-    //i = hts221.begin();  
-    //if(!i) {
-    //    WARN(RED "HTS221 NOT DETECTED!!\n\r");
-    //}
+    humidity_sensor->read_id(&id);
+    printf("HTS221  humidity & temperature    = 0x%X\r\n", id);
+    pressure_sensor->read_id(&id);
+    printf("LPS25H  pressure & temperature    = 0x%X\r\n", id);
       
     // Setup SW3 button to falling edge interrupt
     INFO("Init interrupts...");
@@ -570,8 +582,9 @@
         }
         
         // Read sensor data
-        temperature = 24.5;
-        humidity = 60;
+        temp_sensor1->get_temperature(&iks01a1_temperature);
+        humidity_sensor->get_humidity(&iks01a1_humidity);
+        pressure_sensor->get_pressure(&iks01a1_pressure);
                                 
         INFO("\n=======================================================================================\n");             
         // Initialize JSON shadow document          
@@ -584,10 +597,11 @@
                 buttonOverride = false;
             }
                   
-            // Updates the 'reported' color/temp/humidity
-            rc = aws_iot_shadow_add_reported(JsonDocumentBuffer, sizeOfJsonDocumentBuffer, 3, &ledController,
+            // Updates the 'reported' color/temp/humidity/pressure
+            rc = aws_iot_shadow_add_reported(JsonDocumentBuffer, sizeOfJsonDocumentBuffer, 4, &ledController,
                                                                                               &temperatureHandler,
-                                                                                              &humidityHandler);
+                                                                                              &humidityHandler,
+                                                                                              &pressureHandler);
                  
             if (rc == NONE_ERROR) {               
                 rc = aws_iot_finalize_json_document(JsonDocumentBuffer, sizeOfJsonDocumentBuffer);