Revision 2:aca93337a0e1, committed 2014-02-17

Comitter:

nleoni

Date:

Mon Feb 17 06:35:57 2014 +0000

Parent:

1:d5bb7a2e46c2

Commit message:

Test for PinDetect Library; use "#define DIRECTINT" constant to compile two versions which show how the library works vs the actual InterruptIn library.

Changed in this revision

diff -r d5bb7a2e46c2 -r aca93337a0e1 C12832_lcd.lib
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/C12832_lcd.lib	Mon Feb 17 06:35:57 2014 +0000
@@ -0,0 +1,1 @@
+http://mbed.org/users/dreschpe/code/C12832_lcd/#468cdccff7af

diff -r d5bb7a2e46c2 -r aca93337a0e1 main.cpp
--- a/main.cpp	Sat Feb 15 07:24:47 2014 +0000
+++ b/main.cpp	Mon Feb 17 06:35:57 2014 +0000
@@ -1,14 +1,94 @@
 #include "mbed.h"
 #include "PinDetect.h"
-// must import Cookbook PinDetct library into project
-// URL: http://mbed.org/users/AjK/libraries/PinDetect/lkyxpw
+#include "C12832_lcd.h"
+
+//Napoleon Leoni
+//***************************************************************************//
+//Test program for debounce on interrupt. Here I test the PinDetect Library  //
+//To check whether indeed the library is attaching the debounced pin to an   //
+//interrupt. The conclusion as shown below is that it is NOT!, the PinDetect //
+//has some nice features like key_pressed or key_pressedheld detection       //
+//but they are all working on polling the specified debounced pin on a Timer //
+//interrupt, which by default is set every 20 ms. This is not the same as    //
+//trigering an Interrupt on a leading or trailing edge of GPIO pin           //
+//
+//
+//                  TESTS RUN                                               //
+// I print to the LCD three important LPC1768 registers: 
+// ISER0..Interrupt set Enable register(address 0xE000E100), for this program 
+// the important bits are #4..Timer 3 interrupt and #21 External interrupt 3. 
+// Note that all GPIO interrupts are attached to the External Interrupt 3 
+// hardware EINT3. contents of ISER0 are accesible via: *(NVIC->ISER)
+//
+// IntEnR..GPIO interrupt enable on rising, shows which pins are attached to EINT3 
+// on their rising edge (these are only for mbed pins mapped to LPC pins on Port 0)
+// its contents are available using th macro LPC_GPIOINT->IO0IntEnR
+// IntEnF..GPIO interrupt enable on falling, shows which pins are attached to EINT3 
+// on their falling edge (these are only for mbed pins mapped to LPC pins on Port 0)
+// its contents are available using th macro LPC_GPIOINT->IO0IntEnF
+// 
+// Note the mapping below of MBED pins to the IntEnR/IntEnF bits:
+// IntEnR/IntEnF bit    LPC GPIO       MBED GPIO PIN   
+// 0                    P[0].0          p9                              
+// 1                    P[0].1          p10
+// 4                    P[0].4          p30
+// 5                    P[0].5          p29
+// 6                    P[0].6          p8
+// 7                    P[0].7          p7
+// 8                    P[0].8          p6
+// 9                    P[0].9          p5
+// 10                   P[0].10         p28
+// 11                   P[0].11         p27
+// 12                   P[0].12         p27
+// 15                   P[0].15         p13
+// 16                   P[0].16         p14
+// 17                   P[0].17         p12
+// 18                   P[0].18         p11
+// 23                   P[0].23         p15
+// 24                   P[0].24         p16
+// 25                   P[0].25         p17
+// 26                   P[0].26         p18
+// 30                   P[0].30         p19
+// 31                   P[0].31         p20
+//***********************************************************************************
+//   Test description                 Resulting Register Values                 Analysis
+// 1 DIRECTINT not defined            ISER0       0x0000 0010                   No GPIO interrupts enabled nor attached
+//   so only pinDetect(14)            IO0IntEnR   0x0000 0000                   only TIMER 3 Interrupt enabled so the pinDetect
+//   is used                          IO0IntEnF   0x0000 0000                   libary is simply polling the pin on a timer interrupt and 
+//                                                                              debouncing it. 
+//
+// 2 DIRECTINT defined                ISER0       0x0020 0010(when enabled)     GPIO interrupt is enabled and disabled periodically     
+//                                                0x0000 0010(when disabled)    when disabled the joystick up/down motion does not trigger
+//   so we define InterruptIn         IO0IntEnR   0x0080 0000                   LED1 as expected, however the pindetect functionality continues
+//   on pins 12 and 15                IO0IntEnF   0x0002 0000                   to work a further confirmation that the library is not working with
+//                                                                              an interrupt on the GPIO specified pin. Note that p15 is attached to 
+//                                                                              a rising edge GPIO interrupt and p12 to a falling edge interrupt.
+//***********************************************************************************
+
+#define DIRECTINT //constant to compare interrupt registers when using pindetect vs. using InterrupIn library
 
 DigitalOut myled(LED1);
 DigitalOut myled2(LED2);
 DigitalOut myled3(LED3);
 DigitalOut myled4(LED4);
+C12832_LCD lcd;
 
-PinDetect pb(p14);                  // center of joystick
+#ifdef DIRECTINT
+InterruptIn down(p12);  // DOWN of joystickn note that mbed p12 corresponds to lpc P0[17], should appear as 0x0002 0000 in register LPC_GPIOINT->IO0IntEnR/F
+InterruptIn fire(p15);  // up of joystickn note that mbed p15 corresponds to lpc P0[23], should appear as 0x0080 0000 in register LPC_GPIOINT->IO0IntEnR/F
+#endif
+
+
+PinDetect pb(p14);      // center of joystickn note that mbed p14 corresponds to lpc P0[16] should appear as 0x0001 0000 in register LPC_GPIOINT->IO0IntEnR/F
+
+void ISR1() {           //interrupt service routine used to turn on LED 1 on rising edge of joystick up
+    myled = 1;
+}
+
+void ISR2() {          //interrupt service routing used to turn off LED 1 on falling
+    myled = 0;
+}
+
 // SPST Pushbutton debounced count demo using interrupts and callback
 // no external PullUp resistor needed
 // Pushbutton from P8 to GND.
@@ -25,8 +105,13 @@
     myled3 = (count & 0x02)>>1;
     myled2 = (count & 0x04)>>2;
 }
-int main() {
 
+int main()
+{
+#ifdef DIRECTINT
+   fire.rise(&ISR1);
+   down.fall(&ISR2);
+#endif    
     // Use internal pullup for pushbutton
     //pb.mode(PullUp);                              // don't do this for app board
     // Delay for initial pullup to take effect
@@ -38,9 +123,29 @@
 
     //Blink myled in main routine forever while responding to pb changes
     // via interrupts that activate the callback counter function
+    bool disableInterrupt=false;
+    int counter=0,tdelay=10;
     while (1) {
-        myled = !myled;
-        wait(.5);
+        wait(1);
+        lcd.cls();
+        lcd.locate(0,1);
+        lcd.printf("ISER0=%#010X",*(NVIC->ISER)); //NVIC->ISER holds the address of the ISER0 register
+        lcd.locate(0,10);
+        lcd.printf("IO0 INTEN R=%#010X",LPC_GPIOINT->IO0IntEnR); //This address holds GPIO interrupt attach on rise edge state.
+        lcd.locate(0,20);
+        lcd.printf("IO0 INTEN F=%#010X",LPC_GPIOINT->IO0IntEnF ); //This address holds GPIO interrupt attach on falling edge state
+
+#ifdef DIRECTINT
+        //This section of coe periodically (every 10 seconds) toggles the external interrupt 3 EINT3
+        //state between enabled and disabled. This is the hardware interrupt used for th GPIO pins
+        counter++;
+        if(counter>=tdelay){
+            disableInterrupt=!disableInterrupt;
+            if(disableInterrupt)  NVIC_DisableIRQ(EINT3_IRQn);            //disable EINT3
+            if(!disableInterrupt) NVIC_EnableIRQ(EINT3_IRQn);             //re-enable EINT3 
+            counter=0;
+        }
+#endif        
     }
 
 }
\ No newline at end of file

diff -r d5bb7a2e46c2 -r aca93337a0e1 mbed.bld
--- a/mbed.bld	Sat Feb 15 07:24:47 2014 +0000
+++ /dev/null	Thu Jan 01 00:00:00 1970 +0000
@@ -1,1 +0,0 @@
-http://mbed.org/users/mbed_official/code/mbed/builds/63bcd7ba4912

diff -r d5bb7a2e46c2 -r aca93337a0e1 mbed.lib
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed.lib	Mon Feb 17 06:35:57 2014 +0000
@@ -0,0 +1,1 @@
+http://mbed.org/users/mbed_official/code/mbed/#63bcd7ba4912