Diff: Drivers/BSP/STM32746G-Discovery/stm32746g_discovery.h

Revision:

14:1a18e061d0ec

Parent:

13:85dbcff443aa

--- a/Drivers/BSP/STM32746G-Discovery/stm32746g_discovery.h	Wed Nov 27 08:29:42 2019 +0000
+++ /dev/null	Thu Jan 01 00:00:00 1970 +0000
@@ -1,339 +0,0 @@
-/**
-  ******************************************************************************
-  * @file    stm32746g_discovery.h
-  * @author  MCD Application Team
-  * @brief   This file contains definitions for STM32746G_DISCOVERY's LEDs,
-  *          push-buttons and COM ports hardware resources.
-  ******************************************************************************
-  * @attention
-  *
-  * <h2><center>&copy; COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
-  *
-  * Redistribution and use in source and binary forms, with or without modification,
-  * are permitted provided that the following conditions are met:
-  *   1. Redistributions of source code must retain the above copyright notice,
-  *      this list of conditions and the following disclaimer.
-  *   2. Redistributions in binary form must reproduce the above copyright notice,
-  *      this list of conditions and the following disclaimer in the documentation
-  *      and/or other materials provided with the distribution.
-  *   3. Neither the name of STMicroelectronics nor the names of its contributors
-  *      may be used to endorse or promote products derived from this software
-  *      without specific prior written permission.
-  *
-  * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
-  * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
-  * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
-  * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
-  * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
-  * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
-  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
-  * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
-  * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
-  * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
-  *
-  ******************************************************************************
-  */ 
-  
-/* Define to prevent recursive inclusion -------------------------------------*/
-#ifndef __STM32746G_DISCOVERY_H
-#define __STM32746G_DISCOVERY_H
-
-#ifdef __cplusplus
- extern "C" {
-#endif
-
-/* Includes ------------------------------------------------------------------*/
-#include "stm32f7xx_hal.h"
-   
-/** @addtogroup BSP
-  * @{
-  */
-
-/** @addtogroup STM32746G_DISCOVERY
-  * @{
-  */
-      
-/** @addtogroup STM32746G_DISCOVERY_LOW_LEVEL
-  * @{
-  */ 
-
-/** @defgroup STM32746G_DISCOVERY_LOW_LEVEL_Exported_Types STM32746G_DISCOVERY_LOW_LEVEL Exported Types
-  * @{
-  */
-typedef enum 
-{
-  DISCO_LED1 = 0, // MBED
-  LED_GREEN = DISCO_LED1, // MBED
-}Led_TypeDef;
-
-typedef enum 
-{  
-  BUTTON_WAKEUP = 0,
-  BUTTON_TAMPER = 1,
-  BUTTON_KEY = 2
-}Button_TypeDef;
-
-typedef enum 
-{  
-  BUTTON_MODE_GPIO = 0,
-  BUTTON_MODE_EXTI = 1
-}ButtonMode_TypeDef;
-
-typedef enum 
-{
-  COM1 = 0,
-  COM2 = 1
-}COM_TypeDef;
-/**
-  * @}
-  */ 
-
-/** @defgroup STM32746G_DISCOVERY_LOW_LEVEL_Exported_Constants STM32746G_DISCOVERY_LOW_LEVEL Exported Constants
-  * @{
-  */ 
-
-/** 
-  * @brief  Define for STM32746G_DISCOVERY board
-  */ 
-#if !defined (USE_STM32746G_DISCO)
- #define USE_STM32746G_DISCO
-#endif
-
-/** @addtogroup STM32746G_DISCOVERY_LOW_LEVEL_LED
-  * @{
-  */
-
-#define LEDn                             ((uint8_t)1)
-
-#define LED1_GPIO_PORT                   GPIOI
-#define LED1_GPIO_CLK_ENABLE()           __HAL_RCC_GPIOI_CLK_ENABLE()
-#define LED1_GPIO_CLK_DISABLE()          __HAL_RCC_GPIOI_CLK_DISABLE()
-#define LED1_PIN                         GPIO_PIN_1
-
-/**
-  * @}
-  */
-
-/** @addtogroup STM32746G_DISCOVERY_LOW_LEVEL_BUTTON
-  * @{
-  */ 
-#define BUTTONn                             ((uint8_t)3) 
-
-/**
-  * @brief Wakeup push-button
-  */
-#define WAKEUP_BUTTON_PIN                   GPIO_PIN_11
-#define WAKEUP_BUTTON_GPIO_PORT             GPIOI
-#define WAKEUP_BUTTON_GPIO_CLK_ENABLE()     __HAL_RCC_GPIOI_CLK_ENABLE()
-#define WAKEUP_BUTTON_GPIO_CLK_DISABLE()    __HAL_RCC_GPIOI_CLK_DISABLE()
-#define WAKEUP_BUTTON_EXTI_IRQn             EXTI15_10_IRQn 
-
-/**
-  * @brief Tamper push-button
-  */
-#define TAMPER_BUTTON_PIN                    GPIO_PIN_11
-#define TAMPER_BUTTON_GPIO_PORT              GPIOI
-#define TAMPER_BUTTON_GPIO_CLK_ENABLE()      __HAL_RCC_GPIOI_CLK_ENABLE()
-#define TAMPER_BUTTON_GPIO_CLK_DISABLE()     __HAL_RCC_GPIOI_CLK_DISABLE()
-#define TAMPER_BUTTON_EXTI_IRQn              EXTI15_10_IRQn
-
-/**
-  * @brief Key push-button
-  */
-#define KEY_BUTTON_PIN                       GPIO_PIN_11
-#define KEY_BUTTON_GPIO_PORT                 GPIOI
-#define KEY_BUTTON_GPIO_CLK_ENABLE()         __HAL_RCC_GPIOI_CLK_ENABLE()
-#define KEY_BUTTON_GPIO_CLK_DISABLE()        __HAL_RCC_GPIOI_CLK_DISABLE()
-#define KEY_BUTTON_EXTI_IRQn                 EXTI15_10_IRQn
-
-#define BUTTONx_GPIO_CLK_ENABLE(__INDEX__)    do { if((__INDEX__) == 0) WAKEUP_BUTTON_GPIO_CLK_ENABLE(); else\
-                                                   if((__INDEX__) == 1) TAMPER_BUTTON_GPIO_CLK_ENABLE(); else\
-												                        KEY_BUTTON_GPIO_CLK_ENABLE(); } while(0)											   
-
-#define BUTTONx_GPIO_CLK_DISABLE(__INDEX__)    (((__INDEX__) == 0) ? WAKEUP_BUTTON_GPIO_CLK_DISABLE() :\
-                                                ((__INDEX__) == 1) ? TAMPER_BUTTON_GPIO_CLK_DISABLE() : KEY_BUTTON_GPIO_CLK_DISABLE())
-
-/**
-  * @}
-  */
-
-/** @addtogroup STM32746G_DISCOVERY_LOW_LEVEL_SIGNAL
-  * @{
-  */
-#define SIGNALn                             ((uint8_t)1)
-
-/**
-  * @brief SD-detect signal
-  */
-#define SD_DETECT_PIN                        GPIO_PIN_13
-#define SD_DETECT_GPIO_PORT                  GPIOC
-#define SD_DETECT_GPIO_CLK_ENABLE()          __HAL_RCC_GPIOC_CLK_ENABLE()
-#define SD_DETECT_GPIO_CLK_DISABLE()         __HAL_RCC_GPIOC_CLK_DISABLE()
-#define SD_DETECT_EXTI_IRQn                  EXTI15_10_IRQn
-
-/**
-  * @brief Touch screen interrupt signal
-  */
-#define TS_INT_PIN                           GPIO_PIN_13
-#define TS_INT_GPIO_PORT                     GPIOI
-#define TS_INT_GPIO_CLK_ENABLE()             __HAL_RCC_GPIOI_CLK_ENABLE()
-#define TS_INT_GPIO_CLK_DISABLE()            __HAL_RCC_GPIOI_CLK_DISABLE()
-#define TS_INT_EXTI_IRQn                     EXTI15_10_IRQn
-
-/**
-  * @}
-  */ 
-
-/** @addtogroup STM32746G_DISCOVERY_LOW_LEVEL_COM
-  * @{
-  */
-#define COMn                             ((uint8_t)1)
-
-/**
- * @brief Definition for COM port1, connected to USART1
- */ 
-#define DISCOVERY_COM1                          USART1
-#define DISCOVERY_COM1_CLK_ENABLE()             __HAL_RCC_USART1_CLK_ENABLE()
-#define DISCOVERY_COM1_CLK_DISABLE()            __HAL_RCC_USART1_CLK_DISABLE()
-
-#define DISCOVERY_COM1_TX_PIN                   GPIO_PIN_9
-#define DISCOVERY_COM1_TX_GPIO_PORT             GPIOA
-#define DISCOVERY_COM1_TX_GPIO_CLK_ENABLE()     __HAL_RCC_GPIOA_CLK_ENABLE()
-#define DISCOVERY_COM1_TX_GPIO_CLK_DISABLE()    __HAL_RCC_GPIOA_CLK_DISABLE()
-#define DISCOVERY_COM1_TX_AF                    GPIO_AF7_USART1
-
-#define DISCOVERY_COM1_RX_PIN                   GPIO_PIN_7
-#define DISCOVERY_COM1_RX_GPIO_PORT             GPIOB
-#define DISCOVERY_COM1_RX_GPIO_CLK_ENABLE()     __HAL_RCC_GPIOB_CLK_ENABLE()
-#define DISCOVERY_COM1_RX_GPIO_CLK_DISABLE()    __HAL_RCC_GPIOB_CLK_DISABLE()
-#define DISCOVERY_COM1_RX_AF                    GPIO_AF7_USART1
-
-#define DISCOVERY_COM1_IRQn                     USART1_IRQn
-
-#define DISCOVERY_COMx_CLK_ENABLE(__INDEX__)            do { if((__INDEX__) == COM1) DISCOVERY_COM1_CLK_ENABLE(); } while(0)
-#define DISCOVERY_COMx_CLK_DISABLE(__INDEX__)           (((__INDEX__) == 0) ? DISCOVERY_COM1_CLK_DISABLE() : 0)
-
-#define DISCOVERY_COMx_TX_GPIO_CLK_ENABLE(__INDEX__)    do { if((__INDEX__) == COM1) DISCOVERY_COM1_TX_GPIO_CLK_ENABLE(); } while(0)
-#define DISCOVERY_COMx_TX_GPIO_CLK_DISABLE(__INDEX__)   (((__INDEX__) == 0) ? DISCOVERY_COM1_TX_GPIO_CLK_DISABLE() : 0)
-
-#define DISCOVERY_COMx_RX_GPIO_CLK_ENABLE(__INDEX__)    do { if((__INDEX__) == COM1) DISCOVERY_COM1_RX_GPIO_CLK_ENABLE(); } while(0)
-#define DISCOVERY_COMx_RX_GPIO_CLK_DISABLE(__INDEX__)   (((__INDEX__) == 0) ? DISCOVERY_COM1_RX_GPIO_CLK_DISABLE() : 0)
-
-/* Exported constant IO ------------------------------------------------------*/
-
-#define LCD_I2C_ADDRESS                  ((uint16_t)0x70)
-#define CAMERA_I2C_ADDRESS               ((uint16_t)0x60)
-#define AUDIO_I2C_ADDRESS                ((uint16_t)0x34)
-#define EEPROM_I2C_ADDRESS_A01           ((uint16_t)0xA0)
-#define EEPROM_I2C_ADDRESS_A02           ((uint16_t)0xA6)
-#define TS_I2C_ADDRESS                   ((uint16_t)0x70)
-
-/* I2C clock speed configuration (in Hz) 
-   WARNING: 
-   Make sure that this define is not already declared in other files (ie. 
-   stm32746g_discovery.h file). It can be used in parallel by other modules. */
-#ifndef I2C_SPEED
- #define I2C_SPEED                       ((uint32_t)100000)
-#endif /* I2C_SPEED */
-
-/* User can use this section to tailor I2Cx/I2Cx instance used and associated 
-   resources */
-/* Definition for AUDIO and LCD I2Cx resources */
-#define DISCOVERY_AUDIO_I2Cx                             I2C3
-#define DISCOVERY_AUDIO_I2Cx_CLK_ENABLE()                __HAL_RCC_I2C3_CLK_ENABLE()
-#define DISCOVERY_AUDIO_DMAx_CLK_ENABLE()                __HAL_RCC_DMA1_CLK_ENABLE()
-#define DISCOVERY_AUDIO_I2Cx_SCL_SDA_GPIO_CLK_ENABLE()   __HAL_RCC_GPIOH_CLK_ENABLE()
-
-#define DISCOVERY_AUDIO_I2Cx_FORCE_RESET()               __HAL_RCC_I2C3_FORCE_RESET()
-#define DISCOVERY_AUDIO_I2Cx_RELEASE_RESET()             __HAL_RCC_I2C3_RELEASE_RESET()
-
-/* Definition for I2Cx Pins */
-#define DISCOVERY_AUDIO_I2Cx_SCL_PIN                     GPIO_PIN_7
-#define DISCOVERY_AUDIO_I2Cx_SCL_SDA_GPIO_PORT           GPIOH
-#define DISCOVERY_AUDIO_I2Cx_SCL_SDA_AF                  GPIO_AF4_I2C3
-#define DISCOVERY_AUDIO_I2Cx_SDA_PIN                     GPIO_PIN_8
-
-/* I2C interrupt requests */
-#define DISCOVERY_AUDIO_I2Cx_EV_IRQn                     I2C3_EV_IRQn
-#define DISCOVERY_AUDIO_I2Cx_ER_IRQn                     I2C3_ER_IRQn
-
-/* Definition for external, camera and Arduino connector I2Cx resources */
-#define DISCOVERY_EXT_I2Cx                               I2C1
-#define DISCOVERY_EXT_I2Cx_CLK_ENABLE()                  __HAL_RCC_I2C1_CLK_ENABLE()
-#define DISCOVERY_EXT_DMAx_CLK_ENABLE()                  __HAL_RCC_DMA1_CLK_ENABLE()
-#define DISCOVERY_EXT_I2Cx_SCL_SDA_GPIO_CLK_ENABLE()     __HAL_RCC_GPIOB_CLK_ENABLE()
-
-#define DISCOVERY_EXT_I2Cx_FORCE_RESET()                 __HAL_RCC_I2C1_FORCE_RESET()
-#define DISCOVERY_EXT_I2Cx_RELEASE_RESET()               __HAL_RCC_I2C1_RELEASE_RESET()
-
-/* Definition for I2Cx Pins */
-#define DISCOVERY_EXT_I2Cx_SCL_PIN                       GPIO_PIN_8
-#define DISCOVERY_EXT_I2Cx_SCL_SDA_GPIO_PORT             GPIOB
-#define DISCOVERY_EXT_I2Cx_SCL_SDA_AF                    GPIO_AF4_I2C1
-#define DISCOVERY_EXT_I2Cx_SDA_PIN                       GPIO_PIN_9
-
-/* I2C interrupt requests */
-#define DISCOVERY_EXT_I2Cx_EV_IRQn                       I2C1_EV_IRQn
-#define DISCOVERY_EXT_I2Cx_ER_IRQn                       I2C1_ER_IRQn
-
-/* I2C TIMING Register define when I2C clock source is SYSCLK */
-/* I2C TIMING is calculated from APB1 source clock = 50 MHz */
-/* Due to the big MOFSET capacity for adapting the camera level the rising time is very large (>1us) */
-/* 0x40912732 takes in account the big rising and aims a clock of 100khz */
-#ifndef DISCOVERY_I2Cx_TIMING  
-#define DISCOVERY_I2Cx_TIMING                      ((uint32_t)0x40912732)  
-#endif /* DISCOVERY_I2Cx_TIMING */
-
-/**
-  * @}
-  */ 
-
-/**
-  * @}
-  */ 
-  
-/** @defgroup STM32746G_DISCOVERY_LOW_LEVEL_Exported_Macros STM32746G_DISCOVERY_LOW_LEVEL Exported Macros
-  * @{
-  */  
-/**
-  * @}
-  */ 
-
-/** @addtogroup STM32746G_DISCOVERY_LOW_LEVEL_Exported_Functions
-  * @{
-  */
-uint32_t  BSP_GetVersion(void);
-void      BSP_LED_Init(Led_TypeDef Led);
-void      BSP_LED_DeInit(Led_TypeDef Led);
-void      BSP_LED_On(Led_TypeDef Led);
-void      BSP_LED_Off(Led_TypeDef Led);
-void      BSP_LED_Toggle(Led_TypeDef Led);
-void      BSP_PB_Init(Button_TypeDef Button, ButtonMode_TypeDef ButtonMode);
-void      BSP_PB_DeInit(Button_TypeDef Button);
-uint32_t  BSP_PB_GetState(Button_TypeDef Button);
-void      BSP_COM_Init(COM_TypeDef COM, UART_HandleTypeDef *husart);
-void      BSP_COM_DeInit(COM_TypeDef COM, UART_HandleTypeDef *huart);
-
-/**
-  * @}
-  */
-
-/**
-  * @}
-  */ 
-
-/**
-  * @}
-  */ 
-
-/**
-  * @}
-  */
-
-#ifdef __cplusplus
-}
-#endif
-
-#endif /* __STM32746G_DISCOVERY_H */
-
-/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/