mbed library sources
Fork of mbed-src by
Diff: targets/cmsis/TARGET_STM/TARGET_NUCLEO_L152RE/stm32l1xx_hal_lcd.c
- Revision:
- 354:e67efb2aab0e
--- /dev/null Thu Jan 01 00:00:00 1970 +0000 +++ b/targets/cmsis/TARGET_STM/TARGET_NUCLEO_L152RE/stm32l1xx_hal_lcd.c Thu Oct 16 15:00:10 2014 +0100 @@ -0,0 +1,610 @@ +/** + ****************************************************************************** + * @file stm32l1xx_hal_lcd.c + * @author MCD Application Team + * @version V1.0.0 + * @date 5-September-2014 + * @brief LCD Controller HAL module driver. + * This file provides firmware functions to manage the following + * functionalities of the LCD Controller (LCD) peripheral: + * + Initialization/de-initialization methods + * + I/O operation methods + * + Peripheral State methods + * + @verbatim + ============================================================================== + ##### How to use this driver ##### + ============================================================================== + [..] The LCD HAL driver can be used as follows: + + (#) Declare a LCD_HandleTypeDef handle structure. + + (#) Initialize the LCD low level resources by implement the HAL_LCD_MspInit() API: + (##) Enable the LCDCLK (same as RTCCLK): to configure the RTCCLK/LCDCLK, proceed as follows: + (+) Use RCC function HAL_RCCEx_PeriphCLKConfig in indicating RCC_PERIPHCLK_LCD and + selected clock source (HSE, LSI or LSE) + + -@- The frequency generator allows you to achieve various LCD frame rates + starting from an LCD input clock frequency (LCDCLK) which can vary + from 32 kHz up to 1 MHz. + (##) LCD pins configuration: + (+) Enable the clock for the LCD GPIOs. + (+) Configure these LCD pins as alternate function no-pull. + (##) Enable the LCD interface clock. + + (#) Program the Prescaler, Divider, Blink mode, Blink Frequency Duty, Bias, + Voltage Source, Dead Time, Pulse On Duration and Contrast in the hlcd Init structure. + + (#) Initialize the LCD registers by calling the HAL_LCD_Init() API. + + -@- The HAL_LCD_Init() API configures also the low level Hardware GPIO, CLOCK, ...etc) + by calling the custumed HAL_LCD_MspInit() API. + -@- After calling the HAL_LCD_Init() the LCD RAM memory is cleared + + (#) Optionally you can update the LCD configuration using these macros: + (+) LCD High Drive using the __HAL_LCD_HIGHDRIVER_ENABLE() and __HAL_LCD_HIGHDRIVER_DISABLE() macros + (+) LCD Pulse ON Duration using the __HAL_LCD_PULSEONDURATION_CONFIG() macro + (+) LCD Dead Time using the __HAL_LCD_DEADTIME_CONFIG() macro + (+) The LCD Blink mode and frequency using the __HAL_LCD_BLINK_CONFIG() macro + (+) The LCD Contrast using the __HAL_LCD_CONTRAST_CONFIG() macro + + (#) Write to the LCD RAM memory using the HAL_LCD_Write() API, this API can be called + more time to update the different LCD RAM registers before calling + HAL_LCD_UpdateDisplayRequest() API. + + (#) The HAL_LCD_Clear() API can be used to clear the LCD RAM memory. + + (#) When LCD RAM memory is updated enable the update display request using + the HAL_LCD_UpdateDisplayRequest() API. + + [..] LCD and low power modes: + (#) The LCD remain active during STOP mode. + + @endverbatim + ****************************************************************************** + * @attention + * + * <h2><center>© COPYRIGHT(c) 2014 STMicroelectronics</center></h2> + * + * Redistribution and use in source and binary forms, with or without modification, + * are permitted provided that the following conditions are met: + * 1. Redistributions of source code must retain the above copyright notice, + * this list of conditions and the following disclaimer. + * 2. Redistributions in binary form must reproduce the above copyright notice, + * this list of conditions and the following disclaimer in the documentation + * and/or other materials provided with the distribution. + * 3. Neither the name of STMicroelectronics nor the names of its contributors + * may be used to endorse or promote products derived from this software + * without specific prior written permission. + * + * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" + * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE + * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE + * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE + * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL + * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR + * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER + * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, + * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE + * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. + * + ****************************************************************************** + */ + +/* Includes ------------------------------------------------------------------*/ +#include "stm32l1xx_hal.h" + +/** @addtogroup STM32L1xx_HAL_Driver + * @{ + */ + +#ifdef HAL_LCD_MODULE_ENABLED + +#if defined (STM32L100xB) || defined (STM32L100xBA) || defined (STM32L100xC) ||\ + defined (STM32L152xB) || defined (STM32L152xBA) || defined (STM32L152xC) || defined (STM32L152xCA) || defined (STM32L152xD) || defined (STM32L152xE) ||\ + defined (STM32L162xC) || defined (STM32L162xCA) || defined (STM32L162xD) || defined (STM32L162xE) + +/** @defgroup LCD LCD + * @brief LCD HAL module driver + * @{ + */ + +/* Private typedef -----------------------------------------------------------*/ +/* Private define ------------------------------------------------------------*/ +/** @defgroup LCD_Private_Defines LCD Private Defines + * @{ + */ + +#define LCD_TIMEOUT_VALUE 1000 + +/** + * @} + */ + +/* Private macro -------------------------------------------------------------*/ +/* Private variables ---------------------------------------------------------*/ +/* Private function prototypes -----------------------------------------------*/ +/* Private functions ---------------------------------------------------------*/ + +/** @defgroup LCD_Exported_Functions LCD Exported Functions + * @{ + */ + +/** @defgroup LCD_Exported_Functions_Group1 Initialization/de-initialization methods + * @brief Initialization and Configuration functions + * +@verbatim +=============================================================================== + ##### Initialization and Configuration functions ##### + =============================================================================== + [..] + +@endverbatim + * @{ + */ + +/** + * @brief DeInitializes the LCD peripheral. + * @param hlcd: LCD handle + * @retval HAL status + */ +HAL_StatusTypeDef HAL_LCD_DeInit(LCD_HandleTypeDef *hlcd) +{ + /* Check the LCD handle allocation */ + if(hlcd == HAL_NULL) + { + return HAL_ERROR; + } + + /* Check the parameters */ + assert_param(IS_LCD_ALL_INSTANCE(hlcd->Instance)); + + hlcd->State = HAL_LCD_STATE_BUSY; + + /* DeInit the low level hardware */ + HAL_LCD_MspDeInit(hlcd); + + hlcd->ErrorCode = HAL_LCD_ERROR_NONE; + hlcd->State = HAL_LCD_STATE_RESET; + + /* Release Lock */ + __HAL_UNLOCK(hlcd); + + return HAL_OK; +} + +/** + * @brief Initializes the LCD peripheral according to the specified parameters + * in the LCD_InitStruct. + * @note This function can be used only when the LCD is disabled. + * @param hlcd: LCD handle + * @retval None + */ +HAL_StatusTypeDef HAL_LCD_Init(LCD_HandleTypeDef *hlcd) +{ + uint32_t tickstart = 0x00; + uint8_t counter = 0; + + /* Check the LCD handle allocation */ + if(hlcd == HAL_NULL) + { + return HAL_ERROR; + } + + /* Check function parameters */ + assert_param(IS_LCD_ALL_INSTANCE(hlcd->Instance)); + assert_param(IS_LCD_PRESCALER(hlcd->Init.Prescaler)); + assert_param(IS_LCD_DIVIDER(hlcd->Init.Divider)); + assert_param(IS_LCD_DUTY(hlcd->Init.Duty)); + assert_param(IS_LCD_BIAS(hlcd->Init.Bias)); + assert_param(IS_LCD_VOLTAGE_SOURCE(hlcd->Init.VoltageSource)); + assert_param(IS_LCD_PULSE_ON_DURATION(hlcd->Init.PulseOnDuration)); + assert_param(IS_LCD_DEAD_TIME(hlcd->Init.DeadTime)); + assert_param(IS_LCD_CONTRAST(hlcd->Init.Contrast)); + assert_param(IS_LCD_BLINK_FREQUENCY(hlcd->Init.BlinkFrequency)); + assert_param(IS_LCD_BLINK_MODE(hlcd->Init.BlinkMode)); + assert_param(IS_LCD_MUXSEGMENT(hlcd->Init.MuxSegment)); + + if(hlcd->State == HAL_LCD_STATE_RESET) + { + /* Initialize the low level hardware (MSP) */ + HAL_LCD_MspInit(hlcd); + } + + hlcd->State = HAL_LCD_STATE_BUSY; + + /* Disable the peripheral */ + __HAL_LCD_DISABLE(hlcd); + + /* Clear the LCD_RAM registers and enable the display request by setting the UDR bit + in the LCD_SR register */ + for(counter = LCD_RAM_REGISTER0; counter <= LCD_RAM_REGISTER15; counter++) + { + hlcd->Instance->RAM[counter] = 0; + } + /* Enable the display request */ + hlcd->Instance->SR |= LCD_SR_UDR; + + /* Configure the LCD Prescaler, Divider, Blink mode and Blink Frequency: + Set PS[3:0] bits according to hlcd->Init.Prescaler value + Set DIV[3:0] bits according to hlcd->Init.Divider value + Set BLINK[1:0] bits according to hlcd->Init.BlinkMode value + Set BLINKF[2:0] bits according to hlcd->Init.BlinkFrequency value + Set DEAD[2:0] bits according to hlcd->Init.DeadTime value + Set PON[2:0] bits according to hlcd->Init.PulseOnDuration value + Set CC[2:0] bits according to hlcd->Init.Contrast value */ + MODIFY_REG(hlcd->Instance->FCR, \ + (LCD_FCR_PS | LCD_FCR_DIV | LCD_FCR_BLINK| LCD_FCR_BLINKF | \ + LCD_FCR_DEAD | LCD_FCR_PON | LCD_FCR_CC), \ + (hlcd->Init.Prescaler | hlcd->Init.Divider | hlcd->Init.BlinkMode | hlcd->Init.BlinkFrequency | \ + hlcd->Init.DeadTime | hlcd->Init.PulseOnDuration | hlcd->Init.Contrast)); + + /* Wait until LCD Frame Control Register Synchronization flag (FCRSF) is set in the LCD_SR register + This bit is set by hardware each time the LCD_FCR register is updated in the LCDCLK + domain. It is cleared by hardware when writing to the LCD_FCR register.*/ + LCD_WaitForSynchro(hlcd); + + /* Configure the LCD Duty, Bias, Voltage Source, Dead Time, Pulse On Duration and Contrast: + Set DUTY[2:0] bits according to hlcd->Init.Duty value + Set BIAS[1:0] bits according to hlcd->Init.Bias value + Set VSEL bit according to hlcd->Init.VoltageSource value + Set MUX_SEG bit according to hlcd->Init.MuxSegment value */ + MODIFY_REG(hlcd->Instance->CR, \ + (LCD_CR_DUTY | LCD_CR_BIAS | LCD_CR_VSEL | LCD_CR_MUX_SEG), \ + (hlcd->Init.Duty | hlcd->Init.Bias | hlcd->Init.VoltageSource | hlcd->Init.MuxSegment)); + + /* Enable the peripheral */ + __HAL_LCD_ENABLE(hlcd); + + /* Get timeout */ + tickstart = HAL_GetTick(); + + /* Wait Until the LCD is enabled */ + while(__HAL_LCD_GET_FLAG(hlcd, LCD_FLAG_ENS) == RESET) + { + if((HAL_GetTick() - tickstart ) > LCD_TIMEOUT_VALUE) + { + hlcd->ErrorCode = HAL_LCD_ERROR_ENS; + return HAL_TIMEOUT; + } + } + + /* Get timeout */ + tickstart = HAL_GetTick(); + + /*!< Wait Until the LCD Booster is ready */ + while(__HAL_LCD_GET_FLAG(hlcd, LCD_FLAG_RDY) == RESET) + { + if((HAL_GetTick() - tickstart ) > LCD_TIMEOUT_VALUE) + { + hlcd->ErrorCode = HAL_LCD_ERROR_RDY; + return HAL_TIMEOUT; + } + } + + /* Initialize the LCD state */ + hlcd->ErrorCode = HAL_LCD_ERROR_NONE; + hlcd->State= HAL_LCD_STATE_READY; + + return HAL_OK; +} + +/** + * @brief LCD MSP DeInit. + * @param hlcd: LCD handle + * @retval None + */ + __weak void HAL_LCD_MspDeInit(LCD_HandleTypeDef *hlcd) +{ + /* NOTE: This function Should not be modified, when the callback is needed, + the HAL_LCD_MspDeInit could be implemented in the user file + */ +} + +/** + * @brief LCD MSP Init. + * @param hlcd: LCD handle + * @retval None + */ + __weak void HAL_LCD_MspInit(LCD_HandleTypeDef *hlcd) +{ + /* NOTE: This function Should not be modified, when the callback is needed, + the HAL_LCD_MspInit could be implemented in the user file + */ +} + +/** + * @} + */ + +/** @defgroup LCD_Exported_Functions_Group2 IO operation methods + * @brief LCD RAM functions + * +@verbatim + =============================================================================== + ##### IO operation functions ##### + =============================================================================== + [..] Using its double buffer memory the LCD controller ensures the coherency of the + displayed information without having to use interrupts to control LCD_RAM + modification. + The application software can access the first buffer level (LCD_RAM) through + the APB interface. Once it has modified the LCD_RAM using the HAL_LCD_Write() API, + it sets the UDR flag in the LCD_SR register using the HAL_LCD_UpdateDisplayRequest() API. + This UDR flag (update display request) requests the updated information to be + moved into the second buffer level (LCD_DISPLAY). + This operation is done synchronously with the frame (at the beginning of the + next frame), until the update is completed, the LCD_RAM is write protected and + the UDR flag stays high. + Once the update is completed another flag (UDD - Update Display Done) is set and + generates an interrupt if the UDDIE bit in the LCD_FCR register is set. + The time it takes to update LCD_DISPLAY is, in the worst case, one odd and one + even frame. + The update will not occur (UDR = 1 and UDD = 0) until the display is + enabled (LCDEN = 1). + +@endverbatim + * @{ + */ + +/** + * @brief Writes a word in the specific LCD RAM. + * @param hlcd: LCD handle + * @param RAMRegisterIndex: specifies the LCD RAM Register. + * This parameter can be one of the following values: + * @arg LCD_RAM_REGISTER0: LCD RAM Register 0 + * @arg LCD_RAM_REGISTER1: LCD RAM Register 1 + * @arg LCD_RAM_REGISTER2: LCD RAM Register 2 + * @arg LCD_RAM_REGISTER3: LCD RAM Register 3 + * @arg LCD_RAM_REGISTER4: LCD RAM Register 4 + * @arg LCD_RAM_REGISTER5: LCD RAM Register 5 + * @arg LCD_RAM_REGISTER6: LCD RAM Register 6 + * @arg LCD_RAM_REGISTER7: LCD RAM Register 7 + * @arg LCD_RAM_REGISTER8: LCD RAM Register 8 + * @arg LCD_RAM_REGISTER9: LCD RAM Register 9 + * @arg LCD_RAM_REGISTER10: LCD RAM Register 10 + * @arg LCD_RAM_REGISTER11: LCD RAM Register 11 + * @arg LCD_RAM_REGISTER12: LCD RAM Register 12 + * @arg LCD_RAM_REGISTER13: LCD RAM Register 13 + * @arg LCD_RAM_REGISTER14: LCD RAM Register 14 + * @arg LCD_RAM_REGISTER15: LCD RAM Register 15 + * @param RAMRegisterMask: specifies the LCD RAM Register Data Mask. + * @param Data: specifies LCD Data Value to be written. + * @retval None + */ +HAL_StatusTypeDef HAL_LCD_Write(LCD_HandleTypeDef *hlcd, uint32_t RAMRegisterIndex, uint32_t RAMRegisterMask, uint32_t Data) +{ + uint32_t tickstart = 0x00; + + if((hlcd->State == HAL_LCD_STATE_READY) || (hlcd->State == HAL_LCD_STATE_BUSY)) + { + /* Check the parameters */ + assert_param(IS_LCD_RAM_REGISTER(RAMRegisterIndex)); + + if(hlcd->State == HAL_LCD_STATE_READY) + { + /* Process Locked */ + __HAL_LOCK(hlcd); + hlcd->State = HAL_LCD_STATE_BUSY; + + /* Get timeout */ + tickstart = HAL_GetTick(); + + /*!< Wait Until the LCD is ready */ + while(__HAL_LCD_GET_FLAG(hlcd, LCD_FLAG_UDR) != RESET) + { + if((HAL_GetTick() - tickstart ) > LCD_TIMEOUT_VALUE) + { + hlcd->ErrorCode = HAL_LCD_ERROR_UDR; + + /* Process Unlocked */ + __HAL_UNLOCK(hlcd); + + return HAL_TIMEOUT; + } + } + } + + /* Copy the new Data bytes to LCD RAM register */ + MODIFY_REG(hlcd->Instance->RAM[RAMRegisterIndex], ~(RAMRegisterMask), Data); + + return HAL_OK; + } + else + { + return HAL_ERROR; + } +} + +/** + * @brief Clears the LCD RAM registers. + * @param hlcd: LCD handle + * @retval None + */ +HAL_StatusTypeDef HAL_LCD_Clear(LCD_HandleTypeDef *hlcd) +{ + uint32_t tickstart = 0x00; + uint32_t counter = 0; + + if((hlcd->State == HAL_LCD_STATE_READY) || (hlcd->State == HAL_LCD_STATE_BUSY)) + { + /* Process Locked */ + __HAL_LOCK(hlcd); + + hlcd->State = HAL_LCD_STATE_BUSY; + + /* Get timeout */ + tickstart = HAL_GetTick(); + + /*!< Wait Until the LCD is ready */ + while(__HAL_LCD_GET_FLAG(hlcd, LCD_FLAG_UDR) != RESET) + { + if((HAL_GetTick() - tickstart ) > LCD_TIMEOUT_VALUE) + { + hlcd->ErrorCode = HAL_LCD_ERROR_UDR; + + /* Process Unlocked */ + __HAL_UNLOCK(hlcd); + + return HAL_TIMEOUT; + } + } + /* Clear the LCD_RAM registers */ + for(counter = LCD_RAM_REGISTER0; counter <= LCD_RAM_REGISTER15; counter++) + { + hlcd->Instance->RAM[counter] = 0; + } + + /* Update the LCD display */ + HAL_LCD_UpdateDisplayRequest(hlcd); + + return HAL_OK; + } + else + { + return HAL_ERROR; + } +} + +/** + * @brief Enables the Update Display Request. + * @param hlcd: LCD handle + * @note Each time software modifies the LCD_RAM it must set the UDR bit to + * transfer the updated data to the second level buffer. + * The UDR bit stays set until the end of the update and during this + * time the LCD_RAM is write protected. + * @note When the display is disabled, the update is performed for all + * LCD_DISPLAY locations. + * When the display is enabled, the update is performed only for locations + * for which commons are active (depending on DUTY). For example if + * DUTY = 1/2, only the LCD_DISPLAY of COM0 and COM1 will be updated. + * @retval None + */ +HAL_StatusTypeDef HAL_LCD_UpdateDisplayRequest(LCD_HandleTypeDef *hlcd) +{ + uint32_t tickstart = 0x00; + + /* Clear the Update Display Done flag before starting the update display request */ + __HAL_LCD_CLEAR_FLAG(hlcd, LCD_FLAG_UDD); + + /* Enable the display request */ + hlcd->Instance->SR |= LCD_SR_UDR; + + /* Get timeout */ + tickstart = HAL_GetTick(); + + /*!< Wait Until the LCD display is done */ + while(__HAL_LCD_GET_FLAG(hlcd, LCD_FLAG_UDD) == RESET) + { + if((HAL_GetTick() - tickstart ) > LCD_TIMEOUT_VALUE) + { + hlcd->ErrorCode = HAL_LCD_ERROR_UDD; + + /* Process Unlocked */ + __HAL_UNLOCK(hlcd); + + return HAL_TIMEOUT; + } + } + + hlcd->State = HAL_LCD_STATE_READY; + + /* Process Unlocked */ + __HAL_UNLOCK(hlcd); + + return HAL_OK; +} + +/** + * @} + */ + +/** @defgroup LCD_Exported_Functions_Group3 Peripheral State methods + * @brief LCD State functions + * +@verbatim + =============================================================================== + ##### Peripheral State functions ##### + =============================================================================== + [..] + This subsection provides a set of functions allowing to control the LCD: + (+) HAL_LCD_GetState() API can be helpful to check in run-time the state of the LCD peripheral State. + (+) HAL_LCD_GetError() API to return the LCD error code. +@endverbatim + * @{ + */ + +/** + * @brief Returns the LCD state. + * @param hlcd: LCD handle + * @retval HAL state + */ +HAL_LCD_StateTypeDef HAL_LCD_GetState(LCD_HandleTypeDef *hlcd) +{ + return hlcd->State; +} + +/** + * @brief Return the LCD error code + * @param hlcd: LCD handle + * @retval LCD Error Code + */ +uint32_t HAL_LCD_GetError(LCD_HandleTypeDef *hlcd) +{ + return hlcd->ErrorCode; +} + +/** + * @} + */ + +/** + * @} + */ + +/** @defgroup LCD_Private_Functions LCD Private Functions + * @{ + */ + +/** + * @brief Waits until the LCD FCR register is synchronized in the LCDCLK domain. + * This function must be called after any write operation to LCD_FCR register. + * @retval None + */ +HAL_StatusTypeDef LCD_WaitForSynchro(LCD_HandleTypeDef *hlcd) +{ + uint32_t tickstart = 0x00; + + /* Get timeout */ + tickstart = HAL_GetTick(); + + /* Loop until FCRSF flag is set */ + while(__HAL_LCD_GET_FLAG(hlcd, LCD_FLAG_FCRSF) == RESET) + { + if((HAL_GetTick() - tickstart ) > LCD_TIMEOUT_VALUE) + { + hlcd->ErrorCode = HAL_LCD_ERROR_FCRSF; + return HAL_TIMEOUT; + } + } + + return HAL_OK; +} + +/** + * @} + */ + +/** + * @} + */ + +#endif /* STM32L100xB || STM32L100xBA || STM32L100xC ||... || STM32L162xD || STM32L162xE */ + +#endif /* HAL_LCD_MODULE_ENABLED */ + +/** + * @} + */ + +/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/ +