Fork of mbed-src file paths change. LPC1114FN28 use only.
Fork of mbed-src by
Information
この情報は2013/10/28時点での解決方法です。
現在はmbed-src、標準ライブラリで問題なくコンパイルが可能です。
・使う物
LPC1114FN28
mbed SDK
LPC1114FN28でmbed-SDKのLibraryを使うとCompile出来ない。(2013/10/28)
パスが通ってないだけのようなのでファイルを以下に移動する。
mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\ mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\TARGET_LPC11XX\ |
にあるファイルをすべて
mbed-src\targets\cmsis\TARGET_NXP\ |
へ移動
mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\にある
TOOLCHAIN_ARM_MICRO |
をフォルダごと
mbed-src\targets\cmsis\TARGET_NXP\ |
へ移動
mbed-src\targets\hal\TARGET_NXP\TARGET_LPC11XX_11CXX\ mbed-src\targets\hal\TARGET_NXP\TARGET_LPC11XX_11CXX\TARGET_LPC11XX\ |
にあるファイルをすべて
mbed-src\targets\hal\TARGET_NXP\ |
へ移動
移動後は以下のような構成になると思います。
※不要なファイルは削除してあります。
ファイルの移動が面倒なので以下に本家からフォークしたライブラリを置いておきます。
Import librarymbed-src-LPC1114FN28
Fork of mbed-src file paths change. LPC1114FN28 use only.
エラーが出力される場合
"TOOLCHAIN_ARM_MICRO"が無いとエラーになる。
Error: Undefined symbol _initial_sp (referred from entry2.o). Error: Undefined symbol _heap_base (referred from malloc.o). Error: Undefined symbol _heap_limit (referred from malloc.o). |
LPC1114FN28はMicrolibを使ってCompileされるため上記のエラーになるようです。
Diff: targets/hal/TARGET_STM/TARGET_STM32F4XX/port_api.c
- Revision:
- 43:b3acfef78949
- Parent:
- 42:7ca0bbba899b
--- a/targets/hal/TARGET_STM/TARGET_STM32F4XX/port_api.c Sun Oct 27 16:30:04 2013 +0000 +++ /dev/null Thu Jan 01 00:00:00 1970 +0000 @@ -1,83 +0,0 @@ -/* mbed Microcontroller Library - * Copyright (c) 2006-2013 ARM Limited - * - * Licensed under the Apache License, Version 2.0 (the "License"); - * you may not use this file except in compliance with the License. - * You may obtain a copy of the License at - * - * http://www.apache.org/licenses/LICENSE-2.0 - * - * Unless required by applicable law or agreed to in writing, software - * distributed under the License is distributed on an "AS IS" BASIS, - * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. - * See the License for the specific language governing permissions and - * limitations under the License. - */ -#include "port_api.h" -#include "pinmap.h" -#include "gpio_api.h" - -#if DEVICE_PORTIN || DEVICE_PORTOUT - -PinName port_pin(PortName port, int pin_n) { - return pin_n + (port << 4); -} - -void port_init(port_t *obj, PortName port, int mask, PinDirection dir) { - obj->port = port; - obj->mask = mask; - - uint32_t port_index = (uint32_t) port; - - GPIO_TypeDef *port_reg = (GPIO_TypeDef *)(GPIOA_BASE + (port_index << 10)); - // Enable GPIO peripheral clock - RCC->AHB1ENR |= 1 << port_index; - - obj->reg_mode = &port_reg->MODER; - obj->reg_set = &port_reg->BSRRH; - obj->reg_clr = &port_reg->BSRRL; - obj->reg_in = &port_reg->IDR; - obj->reg_out = &port_reg->ODR; - - port_dir(obj, dir); -} - -void port_mode(port_t *obj, PinMode mode) { - uint32_t i; - // The mode is set per pin: reuse pinmap logic - for (i=0; i<16; i++) { - if (obj->mask & (1<<i)) { - pin_mode(port_pin(obj->port, i), mode); - } - } -} - -void port_dir(port_t *obj, PinDirection dir) { - obj->direction = dir; - uint32_t tmp = *obj->reg_mode; - for (int i=0; i<16; i++) { - if (obj->mask & (1 << i)) { - // Clear the mode bits (i.e. set to input) - tmp &= ~(0x3 << (i << 1)); - if (dir == PIN_OUTPUT) { - // Set to output - tmp |= 0x1 << (i << 1); - } - } - } - *obj->reg_mode = tmp; -} - -void port_write(port_t *obj, int value) { - *obj->reg_out = (*obj->reg_out & ~obj->mask) | (value & obj->mask); -} - -int port_read(port_t *obj) { - switch (obj->direction) { - case PIN_OUTPUT: return *obj->reg_out & obj->mask; - case PIN_INPUT: return *obj->reg_in & obj->mask; - } - return 0; -} - -#endif