Fork of mbed-src file paths change. LPC1114FN28 use only.
Fork of mbed-src by
Information
この情報は2013/10/28時点での解決方法です。
現在はmbed-src、標準ライブラリで問題なくコンパイルが可能です。
・使う物
LPC1114FN28
mbed SDK
LPC1114FN28でmbed-SDKのLibraryを使うとCompile出来ない。(2013/10/28)
パスが通ってないだけのようなのでファイルを以下に移動する。
mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\ mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\TARGET_LPC11XX\ |
にあるファイルをすべて
mbed-src\targets\cmsis\TARGET_NXP\ |
へ移動
mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\にある
TOOLCHAIN_ARM_MICRO |
をフォルダごと
mbed-src\targets\cmsis\TARGET_NXP\ |
へ移動
mbed-src\targets\hal\TARGET_NXP\TARGET_LPC11XX_11CXX\ mbed-src\targets\hal\TARGET_NXP\TARGET_LPC11XX_11CXX\TARGET_LPC11XX\ |
にあるファイルをすべて
mbed-src\targets\hal\TARGET_NXP\ |
へ移動
移動後は以下のような構成になると思います。
※不要なファイルは削除してあります。
ファイルの移動が面倒なので以下に本家からフォークしたライブラリを置いておきます。
Import librarymbed-src-LPC1114FN28
Fork of mbed-src file paths change. LPC1114FN28 use only.
エラーが出力される場合
"TOOLCHAIN_ARM_MICRO"が無いとエラーになる。
Error: Undefined symbol _initial_sp (referred from entry2.o). Error: Undefined symbol _heap_base (referred from malloc.o). Error: Undefined symbol _heap_limit (referred from malloc.o). |
LPC1114FN28はMicrolibを使ってCompileされるため上記のエラーになるようです。
Diff: targets/hal/TARGET_NXP/TARGET_LPC81X/TARGET_LPC81X_COMMON/us_ticker.c
- Revision:
- 43:b3acfef78949
- Parent:
- 42:7ca0bbba899b
--- a/targets/hal/TARGET_NXP/TARGET_LPC81X/TARGET_LPC81X_COMMON/us_ticker.c Sun Oct 27 16:30:04 2013 +0000 +++ /dev/null Thu Jan 01 00:00:00 1970 +0000 @@ -1,93 +0,0 @@ -/* mbed Microcontroller Library - * Copyright (c) 2006-2013 ARM Limited - * - * Licensed under the Apache License, Version 2.0 (the "License"); - * you may not use this file except in compliance with the License. - * You may obtain a copy of the License at - * - * http://www.apache.org/licenses/LICENSE-2.0 - * - * Unless required by applicable law or agreed to in writing, software - * distributed under the License is distributed on an "AS IS" BASIS, - * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. - * See the License for the specific language governing permissions and - * limitations under the License. - */ -#include <stddef.h> -#include "us_ticker_api.h" -#include "PeripheralNames.h" - -#define US_TICKER_TIMER_IRQn SCT_IRQn - -int us_ticker_inited = 0; - -void us_ticker_init(void) { - if (us_ticker_inited) return; - us_ticker_inited = 1; - - // Enable the SCT clock - LPC_SYSCON->SYSAHBCLKCTRL |= (1 << 8); - - // Clear peripheral reset the SCT: - LPC_SYSCON->PRESETCTRL |= (1 << 8); - - // Unified counter (32 bits) - LPC_SCT->CONFIG |= 1; - - // halt and clear the counter - LPC_SCT->CTRL_L |= (1 << 2) | (1 << 3); - - // System Clock (12)MHz -> us_ticker (1)MHz - LPC_SCT->CTRL_L |= ((SystemCoreClock/1000000 - 1) << 5); - - // unhalt the counter: - // - clearing bit 2 of the CTRL register - LPC_SCT->CTRL_L &= ~(1 << 2); - - NVIC_SetVector(US_TICKER_TIMER_IRQn, (uint32_t)us_ticker_irq_handler); - NVIC_EnableIRQ(US_TICKER_TIMER_IRQn); -} - -uint32_t us_ticker_read() { - if (!us_ticker_inited) - us_ticker_init(); - - return LPC_SCT->COUNT_U; -} - -void us_ticker_set_interrupt(unsigned int timestamp) { - // halt the counter: - // - setting bit 2 of the CTRL register - LPC_SCT->CTRL_L |= (1 << 2); - - // set timestamp in compare register - LPC_SCT->MATCH[0].U = timestamp; - - // unhalt the counter: - // - clearing bit 2 of the CTRL register - LPC_SCT->CTRL_L &= ~(1 << 2); - - // if events are not enabled, enable them - if (!(LPC_SCT->EVEN & 0x01)) { - - // comb mode = match only - LPC_SCT->EVENT[0].CTRL = (1 << 12); - - // ref manual: - // In simple applications that do not - // use states, write 0x01 to this - // register to enable an event - LPC_SCT->EVENT[0].STATE |= 0x1; - - // enable events - LPC_SCT->EVEN |= 0x1; - } -} - -void us_ticker_disable_interrupt(void) { - LPC_SCT->EVEN &= ~1; -} - -void us_ticker_clear_interrupt(void) { - LPC_SCT->EVFLAG = 1; -}