Fork of mbed-src file paths change. LPC1114FN28 use only.
Fork of mbed-src by
Information
この情報は2013/10/28時点での解決方法です。
現在はmbed-src、標準ライブラリで問題なくコンパイルが可能です。
・使う物
LPC1114FN28
mbed SDK
LPC1114FN28でmbed-SDKのLibraryを使うとCompile出来ない。(2013/10/28)
パスが通ってないだけのようなのでファイルを以下に移動する。
mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\ mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\TARGET_LPC11XX\ |
にあるファイルをすべて
mbed-src\targets\cmsis\TARGET_NXP\ |
へ移動
mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\にある
TOOLCHAIN_ARM_MICRO |
をフォルダごと
mbed-src\targets\cmsis\TARGET_NXP\ |
へ移動
mbed-src\targets\hal\TARGET_NXP\TARGET_LPC11XX_11CXX\ mbed-src\targets\hal\TARGET_NXP\TARGET_LPC11XX_11CXX\TARGET_LPC11XX\ |
にあるファイルをすべて
mbed-src\targets\hal\TARGET_NXP\ |
へ移動
移動後は以下のような構成になると思います。
※不要なファイルは削除してあります。
ファイルの移動が面倒なので以下に本家からフォークしたライブラリを置いておきます。
Import librarymbed-src-LPC1114FN28
Fork of mbed-src file paths change. LPC1114FN28 use only.
エラーが出力される場合
"TOOLCHAIN_ARM_MICRO"が無いとエラーになる。
Error: Undefined symbol _initial_sp (referred from entry2.o). Error: Undefined symbol _heap_base (referred from malloc.o). Error: Undefined symbol _heap_limit (referred from malloc.o). |
LPC1114FN28はMicrolibを使ってCompileされるため上記のエラーになるようです。
Diff: targets/hal/TARGET_NXP/TARGET_LPC11XX_11CXX/port_api.c
- Revision:
- 43:b3acfef78949
- Parent:
- 42:7ca0bbba899b
--- a/targets/hal/TARGET_NXP/TARGET_LPC11XX_11CXX/port_api.c Sun Oct 27 16:30:04 2013 +0000 +++ /dev/null Thu Jan 01 00:00:00 1970 +0000 @@ -1,78 +0,0 @@ -/* mbed Microcontroller Library - * Copyright (c) 2006-2013 ARM Limited - * - * Licensed under the Apache License, Version 2.0 (the "License"); - * you may not use this file except in compliance with the License. - * You may obtain a copy of the License at - * - * http://www.apache.org/licenses/LICENSE-2.0 - * - * Unless required by applicable law or agreed to in writing, software - * distributed under the License is distributed on an "AS IS" BASIS, - * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. - * See the License for the specific language governing permissions and - * limitations under the License. - */ - -#include "port_api.h" -#include "pinmap.h" -#include "gpio_api.h" - -// LPC114 IOCON offset table [port][pin] - -static uint8_t iocon_offset[4][12] = { - {0x0c,0x10,0x1c,0x2c,0x30,0x34,0x4c,0x50,0x60,0x64,0x68,0x74}, // PORT 0 - {0x78,0x7c,0x80,0x90,0x94,0xa0,0xa4,0xa8,0x14,0x38,0x6c,0x98}, // PORT 1 - {0x08,0x28,0x5c,0x8c,0x40,0x44,0x00,0x20,0x24,0x54,0x58,0x70}, // PORT 2 - {0x84,0x88,0x9c,0xac,0x3c,0x48} // PORT 3 -}; - -PinName port_pin(PortName port, int pin) { - return (PinName)((port << PORT_SHIFT) | (pin << PIN_SHIFT) | (uint32_t)iocon_offset[port][pin]); -} - -void port_init(port_t *obj, PortName port, int mask, PinDirection dir) { - obj->port = port; - obj->mask = mask; - - LPC_GPIO_TypeDef *port_reg = ((LPC_GPIO_TypeDef *) (LPC_GPIO0_BASE + (port * 0x10000))); - - obj->reg_data = &port_reg->DATA; - obj->reg_dir = &port_reg->DIR; - - uint32_t i; - // The function is set per pin: reuse gpio logic - for (i=0; i<12; i++) { - if (obj->mask & (1<<i)) { - gpio_set(port_pin(obj->port, i)); - } - } - - port_dir(obj, dir); -} - -void port_mode(port_t *obj, PinMode mode) { - uint32_t i; - // The mode is set per pin: reuse pinmap logic - for (i=0; i<12; i++) { - if (obj->mask & (1<<i)) { - pin_mode(port_pin(obj->port, i), mode); - } - } -} - -void port_dir(port_t *obj, PinDirection dir) { - switch (dir) { - case PIN_INPUT : *obj->reg_dir &= ~obj->mask; break; - case PIN_OUTPUT: *obj->reg_dir |= obj->mask; break; - } -} - -void port_write(port_t *obj, int value) { - *obj->reg_data = (value & obj->mask); -} - -int port_read(port_t *obj) { - return (*obj->reg_data & obj->mask); -} -