Fork of mbed-src file paths change. LPC1114FN28 use only.
Fork of mbed-src by
Information
この情報は2013/10/28時点での解決方法です。
現在はmbed-src、標準ライブラリで問題なくコンパイルが可能です。
・使う物
LPC1114FN28
mbed SDK
LPC1114FN28でmbed-SDKのLibraryを使うとCompile出来ない。(2013/10/28)
パスが通ってないだけのようなのでファイルを以下に移動する。
mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\ mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\TARGET_LPC11XX\ |
にあるファイルをすべて
mbed-src\targets\cmsis\TARGET_NXP\ |
へ移動
mbed-src\targets\cmsis\TARGET_NXP\TARGET_LPC11XX_11CXX\にある
TOOLCHAIN_ARM_MICRO |
をフォルダごと
mbed-src\targets\cmsis\TARGET_NXP\ |
へ移動
mbed-src\targets\hal\TARGET_NXP\TARGET_LPC11XX_11CXX\ mbed-src\targets\hal\TARGET_NXP\TARGET_LPC11XX_11CXX\TARGET_LPC11XX\ |
にあるファイルをすべて
mbed-src\targets\hal\TARGET_NXP\ |
へ移動
移動後は以下のような構成になると思います。
※不要なファイルは削除してあります。
ファイルの移動が面倒なので以下に本家からフォークしたライブラリを置いておきます。
Import librarymbed-src-LPC1114FN28
Fork of mbed-src file paths change. LPC1114FN28 use only.
エラーが出力される場合
"TOOLCHAIN_ARM_MICRO"が無いとエラーになる。
Error: Undefined symbol _initial_sp (referred from entry2.o). Error: Undefined symbol _heap_base (referred from malloc.o). Error: Undefined symbol _heap_limit (referred from malloc.o). |
LPC1114FN28はMicrolibを使ってCompileされるため上記のエラーになるようです。
Diff: targets/hal/TARGET_Freescale/TARGET_KL25Z/rtc_api.c
- Revision:
- 43:b3acfef78949
- Parent:
- 42:7ca0bbba899b
--- a/targets/hal/TARGET_Freescale/TARGET_KL25Z/rtc_api.c Sun Oct 27 16:30:04 2013 +0000 +++ /dev/null Thu Jan 01 00:00:00 1970 +0000 @@ -1,91 +0,0 @@ -/* mbed Microcontroller Library - * Copyright (c) 2006-2013 ARM Limited - * - * Licensed under the Apache License, Version 2.0 (the "License"); - * you may not use this file except in compliance with the License. - * You may obtain a copy of the License at - * - * http://www.apache.org/licenses/LICENSE-2.0 - * - * Unless required by applicable law or agreed to in writing, software - * distributed under the License is distributed on an "AS IS" BASIS, - * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied. - * See the License for the specific language governing permissions and - * limitations under the License. - */ -#include "rtc_api.h" - -static void init(void) { - // enable PORTC clock - SIM->SCGC5 |= SIM_SCGC5_PORTC_MASK; - - // enable RTC clock - SIM->SCGC6 |= SIM_SCGC6_RTC_MASK; - - /* - * configure PTC1 with alternate function 1: RTC_CLKIN - * As the kl25z board does not have a 32kHz osc, - * we use an external clock generated by the - * interface chip - */ - PORTC->PCR[1] &= ~PORT_PCR_MUX_MASK; - PORTC->PCR[1] = PORT_PCR_MUX(1); - - // select RTC_CLKIN as RTC clock source - SIM->SOPT1 &= ~SIM_SOPT1_OSC32KSEL_MASK; - SIM->SOPT1 |= SIM_SOPT1_OSC32KSEL(2); -} - -void rtc_init(void) { - init(); - - //Configure the TSR. default value: 1 - RTC->TSR = 1; - - // enable counter - RTC->SR |= RTC_SR_TCE_MASK; -} - -void rtc_free(void) { - // [TODO] -} - -/* - * Little check routine to see if the RTC has been enabled - * 0 = Disabled, 1 = Enabled - */ -int rtc_isenabled(void) { - // even if the RTC module is enabled, - // as we use RTC_CLKIN and an external clock, - // we need to reconfigure the pins. That is why we - // call init() if the rtc is enabled - - // if RTC not enabled return 0 - SIM->SCGC5 |= SIM_SCGC5_PORTC_MASK; - SIM->SCGC6 |= SIM_SCGC6_RTC_MASK; - if ((RTC->SR & RTC_SR_TCE_MASK) == 0) - return 0; - - init(); - return 1; -} - -time_t rtc_read(void) { - return RTC->TSR; -} - -void rtc_write(time_t t) { - // disable counter - RTC->SR &= ~RTC_SR_TCE_MASK; - - // we do not write 0 into TSR - // to avoid invalid time - if (t == 0) - t = 1; - - // write seconds - RTC->TSR = t; - - // re-enable counter - RTC->SR |= RTC_SR_TCE_MASK; -}