first 2016/02 SDFileSystemDMA inherited from Official SDFileSystem.

Dependents:   SDFileSystemDMA-test DmdFullRGB_0_1

Fork of SDFileSystemDMA by mi mi

SDFileSystemDMA is enhanced SDFileSystem library for STM32 micros by using DMA functionality.
Max read transfer rate reaches over 2MByte/sec at 24MHz SPI clock if enough read buffer size is set.
Even though minimum read buffer size (512Byte) is set, read transfer rate will reach over 1MByte/sec at 24MHz SPI Clock.
( but depends on the ability of each SD card)

Test program is here.
https://developer.mbed.org/users/mimi3/code/SDFileSystemDMA-test/

/media/uploads/mimi3/sdfilesystemdma-speed-test3-read-buffer-512byte.png

/media/uploads/mimi3/sdfilesystemdma-speed-test-buffer-vs-spi-clock-nucleo-f411re-96mhz.png

Supported SPI port is shown below table.

(v): Verified. It works well.
(w): Probably it will work well. (not tested)
(c): Only compiled. (not tested)
(f): Over flash.
(r): Only read mode. (when _FS_READONLY==1)
(u) Under construction
(z): Dose not work.

Caution

If your board has SRAM less than or equal to 8KB, the buffer size must be set to 512 Bytes.

Supported Boards:
Cortex-M0

BoardSRAMSPI1SPI2SPI3
NUCLEO-F030R88KB(v)
DISCO-F051R88KB(w)
NUCLEO-F031K64KB(f)
NUCLEO-F042K66KB(r)
NUCLEO-F070RB16KB(w)
NUCLEO-F072RB16KB(w)
NUCLEO-F091RC32KB(c)

Cortex-L0

BoardSRAMSPI1SPI2SPI3
DISCO-L053C88KB(c)
NUCLEO-L053R88KB(c)
NUCLEO-L073RZ20KB(c)

Cortex-M3

BoardSRAMSPI1SPI2SPI3
DISCO-F100RB8KB(v)(v)-
BLUEPILL-F103CB20KB(w)(w)-
NUCLEO-F103RB20KB(v)(v)-
NUCLEO-L152RE80KB(v)(w)-
MOTE-L152RC32KB(w)(w)-

Cortex-M4
F3

BoardSRAMSPI1SPI2SPI3
DISCO-F303VC40KB-(v)(v)
NUCLEO-F303RE64KB(w)(w)(w)
NUCLEO-F302R816KB--(c)
NUCLEO-F303K812KB(c)--
DISCO-F334C812KB(c)--
NUCLEO-F334R812KB(c)--

F4

BoardSPI1SPI2SPI3
ELMO-F411RE(w)-(w)
MTS-MDOT-F411RE(u)-(u)
MTS-DRAGONFLY-F411RE(w)-(w)
NUCLEO-F411RE(v)-(v)
NUCLEO-F401RE(w)-(w)
MTS-MDOT-F405RG(u)-(u)
NUCLEO-F410RB(c)-(c)
NUCLEO-F446RE(c)-(c)
NUCLEO-F429ZI(c)-(c)
B96B-F446VE(c)-(c)
NUCLEO-F446ZE(c)-(c)
DISCO-F429ZI(u)-(u)
DISCO-F469NI(c)-(c)

Information

This library is set to use "short file name" in SDFileSystemDMA/FATFileSystem/ChaN/ffconf.h . ( _USE_LFN=0)
You can change this option to _USE_LFN=1 .

spi_dma/spi_dma_common.c

Committer:
mimi3
Date:
2016-02-14
Revision:
9:367773f8eba4
Parent:
5:809e2eece945
Child:
15:4b0ce6f59b8c

File content as of revision 9:367773f8eba4:

#include "spi_dma.h"

DMA_HandleTypeDef hdma_spi1_tx;
DMA_HandleTypeDef hdma_spi1_rx;
SPI_HandleTypeDef Spi1Handle;

DMA_HandleTypeDef hdma_spi3_tx;
DMA_HandleTypeDef hdma_spi3_rx;
SPI_HandleTypeDef Spi3Handle;
#if 0
	SPI_HandleTypeDef Spi2Handle;
#endif


static void spi_dma_error_handler(void)
{
  while(1)
  { 
	/* infinite loop */
  }
}

static void spi_dma_start( SPI_TypeDef *spi, uint8_t *txbuff, uint8_t *rxbuff, uint16_t count)
{
	SPI_HandleTypeDef *hspi;
	if( spi == SPI1 ) {
		hspi = &Spi1Handle;
	}
#if defined(SPI3_BASE)
	else if( spi == SPI3 ) {
		hspi = &Spi3Handle;
	}
#endif
#if 0
	else{ 
		hspi = &Spi2Handle;
	}
#endif
	if( HAL_SPI_TransmitReceive_DMA( hspi, (uint8_t *)txbuff, (uint8_t *)rxbuff, count) != HAL_OK) {
		spi_dma_error_handler();
	}
}

static void spi_dma_wait_end( SPI_TypeDef *spi )
{
	SPI_HandleTypeDef *hspi;
	if( spi == SPI1 ) {
		hspi = &Spi1Handle;
	} 
#if defined(SPI3_BASE)
	else if( spi == SPI3 ) {
		hspi = &Spi3Handle;
	}
#endif
#if 0
	else{ 
		hspi = &Spi2Handle;
	}
#endif
	while (HAL_SPI_GetState( hspi ) != HAL_SPI_STATE_READY) {
		/* just wait */ 
	} 
}

/* SPI1 init function */
static uint8_t spi_dma_inited = 0;
static void spi_dma_init( SPI_TypeDef *spi)
{
	spi_dma_irq_setup( spi );
}

static void spi_dma_deinit( SPI_TypeDef *spi)
{
	DMA_HandleTypeDef *phdma_rx,*phdma_tx;

	if( spi == SPI1 ) {
		phdma_tx = &hdma_spi1_tx;
		phdma_rx = &hdma_spi1_rx;
	} 
#if defined(SPI3_BASE)
	else if( spi == SPI3 ) {
		phdma_tx = &hdma_spi3_tx;
		phdma_rx = &hdma_spi3_rx;
	} 
#endif
#if 0
	else{ 
	}
#endif
	/* At first, execute DeInit for reset DMA */
	HAL_DMA_DeInit( phdma_tx );
	HAL_DMA_DeInit( phdma_rx );
}

void __spi_dma_read_write( SPI_TypeDef *spi, uint8_t *txbuff, uint8_t *rxbuff, uint16_t count, uint8_t mode)
{
	if( spi_dma_inited == 0 ) {
		spi_dma_inited = 1;
		spi_dma_init( spi );
	}
	spi_dma_get_info( spi );
	spi_dma_handle_setup( spi, mode );	
	spi_dma_start( spi, txbuff, rxbuff, count );
	spi_dma_wait_end( spi );
	//spi_dma_deinit(spi);
}