first 2016/02 SDFileSystemDMA inherited from Official SDFileSystem.
Dependents: SDFileSystemDMA-test DmdFullRGB_0_1
Fork of SDFileSystemDMA by
SDFileSystemDMA is enhanced SDFileSystem library for STM32 micros by using DMA functionality.
Max read transfer rate reaches over 2MByte/sec at 24MHz SPI clock if enough read buffer size is set.
Even though minimum read buffer size (512Byte) is set, read transfer rate will reach over 1MByte/sec at 24MHz SPI Clock.
( but depends on the ability of each SD card)
Test program is here.
https://developer.mbed.org/users/mimi3/code/SDFileSystemDMA-test/
Supported SPI port is shown below table.
(v): Verified. It works well.
(w): Probably it will work well. (not tested)
(c): Only compiled. (not tested)
(f): Over flash.
(r): Only read mode. (when _FS_READONLY==1)
(u) Under construction
(z): Dose not work.
Caution
If your board has SRAM less than or equal to 8KB, the buffer size must be set to 512 Bytes.
Supported Boards:
Cortex-M0
Board | SRAM | SPI1 | SPI2 | SPI3 |
---|---|---|---|---|
NUCLEO-F030R8 | 8KB | (v) | ||
DISCO-F051R8 | 8KB | (w) | ||
4KB | (f) | |||
NUCLEO-F042K6 | 6KB | (r) | ||
NUCLEO-F070RB | 16KB | (w) | ||
NUCLEO-F072RB | 16KB | (w) | ||
NUCLEO-F091RC | 32KB | (c) |
Cortex-L0
Board | SRAM | SPI1 | SPI2 | SPI3 |
---|---|---|---|---|
DISCO-L053C8 | 8KB | (c) | ||
NUCLEO-L053R8 | 8KB | (c) | ||
NUCLEO-L073RZ | 20KB | (c) |
Cortex-M3
Board | SRAM | SPI1 | SPI2 | SPI3 |
---|---|---|---|---|
DISCO-F100RB | 8KB | (v) | (v) | - |
BLUEPILL-F103CB | 20KB | (w) | (w) | - |
NUCLEO-F103RB | 20KB | (v) | (v) | - |
NUCLEO-L152RE | 80KB | (v) | (w) | - |
MOTE-L152RC | 32KB | (w) | (w) | - |
Cortex-M4
F3
Board | SRAM | SPI1 | SPI2 | SPI3 |
---|---|---|---|---|
DISCO-F303VC | 40KB | - | (v) | (v) |
NUCLEO-F303RE | 64KB | (w) | (w) | (w) |
NUCLEO-F302R8 | 16KB | - | - | (c) |
NUCLEO-F303K8 | 12KB | (c) | - | - |
DISCO-F334C8 | 12KB | (c) | - | - |
NUCLEO-F334R8 | 12KB | (c) | - | - |
F4
Board | SPI1 | SPI2 | SPI3 |
---|---|---|---|
ELMO-F411RE | (w) | - | (w) |
MTS-MDOT-F411RE | (u) | - | (u) |
MTS-DRAGONFLY-F411RE | (w) | - | (w) |
NUCLEO-F411RE | (v) | - | (v) |
NUCLEO-F401RE | (w) | - | (w) |
MTS-MDOT-F405RG | (u) | - | (u) |
NUCLEO-F410RB | (c) | - | (c) |
NUCLEO-F446RE | (c) | - | (c) |
NUCLEO-F429ZI | (c) | - | (c) |
B96B-F446VE | (c) | - | (c) |
NUCLEO-F446ZE | (c) | - | (c) |
DISCO-F429ZI | (u) | - | (u) |
DISCO-F469NI | (c) | - | (c) |
Information
This library is set to use "short file name" in SDFileSystemDMA/FATFileSystem/ChaN/ffconf.h . ( _USE_LFN=0)
You can change this option to _USE_LFN=1 .
Diff: SDFileSystemDMA.cpp
- Revision:
- 5:809e2eece945
- Parent:
- 3:23e0dcc750fe
- Child:
- 6:3f25251e2b78
--- a/SDFileSystemDMA.cpp Sat Feb 13 13:27:03 2016 +0000 +++ b/SDFileSystemDMA.cpp Sun Feb 14 15:57:06 2016 +0900 @@ -384,7 +384,11 @@ #define __SPI_DMA__ #include "spi_dma.h" +#if defined(TARGET_DISCO_F303VC) +SPI_TypeDef *spi_id = SPI3; +#else SPI_TypeDef *spi_id = SPI1; +#endif int SDFileSystem::_read(uint8_t *buffer, uint32_t length) { _cs = 0; @@ -394,7 +398,7 @@ // read data #if defined( __SPI_DMA__) uint8_t dummyByte = 0xFF; - spi_dma_read( spi_id, &dummyByte, buffer, length ); + spi_dma_read( spi_id, &dummyByte, buffer, length ); #else for (uint32_t i = 0; i < length; i++) { buffer[i] = _spi.write(0xFF); @@ -408,7 +412,7 @@ return 0; } -int SDFileSystem::_write(const uint8_t*buffer, uint32_t length) { +int SDFileSystem::_write(const uint8_t *buffer, uint32_t length) { _cs = 0; // indicate start of block