Nothing Special / mbed-STM32F103C8

Modification of Mbed-dev library for LQFP48 package microcontrollers: STM32F103C8 (STM32F103C8T6) and STM32F103CB (STM32F103CBT6) (Bluepill boards, Maple mini etc. )

Fork of mbed-STM32F103C8_org by Nothing Special

Library for STM32F103C8 (Bluepill boards etc.).
Use this instead of mbed library.
This library allows the size of the code in the FLASH up to 128kB. Therefore, code also runs on microcontrollers STM32F103CB (eg. Maple mini).
But in the case of STM32F103C8, check the size of the resulting code would not exceed 64kB.

To compile a program with this library, use NUCLEO-F103RB as the target name. !

Changes:

  • Corrected initialization of the HSE + crystal clock (mbed permanent bug), allowing the use of on-board xtal (8MHz).(1)
  • Additionally, it also set USB clock (48Mhz).(2)
  • Definitions of pins and peripherals adjusted to LQFP48 case.
  • Board led LED1 is now PC_13 (3)
  • USER_BUTTON is now PC_14 (4)

    Now the library is complete rebuilt based on mbed-dev v160 (and not yet fully tested).

notes
(1) - In case 8MHz xtal on board, CPU frequency is 72MHz. Without xtal is 64MHz.
(2) - Using the USB interface is only possible if STM32 is clocking by on-board 8MHz xtal or external clock signal 8MHz on the OSC_IN pin.
(3) - On Bluepill board led operation is reversed, i.e. 0 - led on, 1 - led off.
(4) - Bluepill board has no real user button

Information

After export to SW4STM (AC6):

  • add line #include "mbed_config.h" in files Serial.h and RawSerial.h
  • in project properties change Optimisation Level to Optimise for size (-Os)

drivers/RawSerial.h

Committer:
mega64
Date:
2017-04-27
Revision:
148:8b0b02bf146f
Parent:
146:03e976389d16

File content as of revision 148:8b0b02bf146f:

/* mbed Microcontroller Library
 * Copyright (c) 2006-2013 ARM Limited
 *
 * Licensed under the Apache License, Version 2.0 (the "License");
 * you may not use this file except in compliance with the License.
 * You may obtain a copy of the License at
 *
 *     http://www.apache.org/licenses/LICENSE-2.0
 *
 * Unless required by applicable law or agreed to in writing, software
 * distributed under the License is distributed on an "AS IS" BASIS,
 * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
 * See the License for the specific language governing permissions and
 * limitations under the License.
 */
#ifndef MBED_RAW_SERIAL_H
#define MBED_RAW_SERIAL_H

#include "platform/platform.h"

#if DEVICE_SERIAL

#include "drivers/SerialBase.h"
#include "hal/serial_api.h"


namespace mbed {
/** \addtogroup drivers */
/** @{*/

/** A serial port (UART) for communication with other serial devices
 * This is a variation of the Serial class that doesn't use streams,
 * thus making it safe to use in interrupt handlers with the RTOS.
 *
 * Can be used for Full Duplex communication, or Simplex by specifying
 * one pin as NC (Not Connected)
 *
 * @Note Synchronization level: Not protected
 *
 * Example:
 * @code
 * // Send a char to the PC
 *
 * #include "mbed.h"
 *
 * RawSerial pc(USBTX, USBRX);
 *
 * int main() {
 *     pc.putc('A');
 * }
 * @endcode
 */
class RawSerial: public SerialBase {

public:
    /** Create a RawSerial port, connected to the specified transmit and receive pins, with the specified baud.
     *
     *  @param tx Transmit pin
     *  @param rx Receive pin
     *  @param baud The baud rate of the serial port (optional, defaults to MBED_CONF_PLATFORM_DEFAULT_SERIAL_BAUD_RATE)
     *
     *  @note
     *    Either tx or rx may be specified as NC if unused
     */
    RawSerial(PinName tx, PinName rx, int baud = MBED_CONF_PLATFORM_DEFAULT_SERIAL_BAUD_RATE);

    /** Write a char to the serial port
     *
     * @param c The char to write
     *
     * @returns The written char or -1 if an error occured
     */
    int putc(int c);

    /** Read a char from the serial port
     *
     * @returns The char read from the serial port
     */
    int getc();

    /** Write a string to the serial port
     *
     * @param str The string to write
     *
     * @returns 0 if the write succeeds, EOF for error
     */
    int puts(const char *str);

    int printf(const char *format, ...);

protected:

    /** Acquire exclusive access to this serial port
     */
    virtual void lock(void);

    /** Release exclusive access to this serial port
     */
    virtual void unlock(void);
};

} // namespace mbed

#endif

#endif

/** @}*/