File content as of revision 171:3a7713b1edbc:

/**
 * \file
 *
 * \brief SAM Clock Driver
 *
 * Copyright (C) 2012-2015 Atmel Corporation. All rights reserved.
 *
 * \asf_license_start
 *
 * \page License
 *
 * Redistribution and use in source and binary forms, with or without
 * modification, are permitted provided that the following conditions are met:
 *
 * 1. Redistributions of source code must retain the above copyright notice,
 *    this list of conditions and the following disclaimer.
 *
 * 2. Redistributions in binary form must reproduce the above copyright notice,
 *    this list of conditions and the following disclaimer in the documentation
 *    and/or other materials provided with the distribution.
 *
 * 3. The name of Atmel may not be used to endorse or promote products derived
 *    from this software without specific prior written permission.
 *
 * 4. This software may only be redistributed and used in connection with an
 *    Atmel microcontroller product.
 *
 * THIS SOFTWARE IS PROVIDED BY ATMEL "AS IS" AND ANY EXPRESS OR IMPLIED
 * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
 * MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT ARE
 * EXPRESSLY AND SPECIFICALLY DISCLAIMED. IN NO EVENT SHALL ATMEL BE LIABLE FOR
 * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
 * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
 * OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
 * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
 * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN
 * ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
 * POSSIBILITY OF SUCH DAMAGE.
 *
 * \asf_license_stop
 *
 */
/*
 * Support and FAQ: visit <a href="http://www.atmel.com/design-support/">Atmel Support</a>
 */
#ifndef SYSTEM_CLOCK_FEATURE_H_INCLUDED
#define SYSTEM_CLOCK_FEATURE_H_INCLUDED

#ifdef __cplusplus
extern "C" {
#endif

/**
 * \defgroup asfdoc_sam0_system_clock_group SAM System Clock Management Driver (SYSTEM CLOCK)
 *
 * This driver for Atmel&reg; | SMART ARM&reg;-based microcontrollers provides an interface for the configuration
 * and management of the device's clocking related functions. This includes
 * the various clock sources, bus clocks, and generic clocks within the device,
 * with functions to manage the enabling, disabling, source selection, and
 * prescaling of clocks to various internal peripherals.
 *
 * The following peripherals are used by this module:
 *
 * - GCLK (Generic Clock Management)
 * - PM (Power Management)
 * - SYSCTRL (Clock Source Control)
 *
 * The following devices can use this module:
 *  - Atmel | SMART SAM D20/D21
 *  - Atmel | SMART SAM R21
 *  - Atmel | SMART SAM D10/D11
 *  - Atmel | SMART SAM DA0/DA1
 *
 * The outline of this documentation is as follows:
 *  - \ref asfdoc_sam0_system_clock_prerequisites
 *  - \ref asfdoc_sam0_system_clock_module_overview
 *  - \ref asfdoc_sam0_system_clock_special_considerations
 *  - \ref asfdoc_sam0_system_clock_extra_info
 *  - \ref asfdoc_sam0_system_clock_examples
 *  - \ref asfdoc_sam0_system_clock_api_overview
 *
 *
 * \section asfdoc_sam0_system_clock_prerequisites Prerequisites
 *
 * There are no prerequisites for this module.
 *
 *
 * \section asfdoc_sam0_system_clock_module_overview Module Overview
 * The SAM devices contain a sophisticated clocking system, which is designed
 * to give the maximum flexibility to the user application. This system allows
 * a system designer to tune the performance and power consumption of the device
 * in a dynamic manner, to achieve the best trade-off between the two for a
 * particular application.
 *
 * This driver provides a set of functions for the configuration and management
 * of the various clock related functionality within the device.
 *
 * \subsection asfdoc_sam0_system_clock_module_features Driver Feature Macro Definition
 * <table>
 *	<tr>
 *		<th>Driver Feature Macro</th>
 *		<th>Supported devices</th>
 *	</tr>
 *	<tr>
 *		<td>FEATURE_SYSTEM_CLOCK_DPLL</td>
 *		<td>SAMD21, SAMR21, SAMD10, SAMD11, SAMDAx</td>
 *	</tr>
 * </table>
 * \note The specific features are only available in the driver when the
 * selected device supports those features.
 *
 * \subsection asfdoc_sam0_system_clock_module_overview_clock_sources Clock Sources
 * The SAM devices have a number of master clock source modules, each of
 * which being capable of producing a stabilized output frequency, which can then
 * be fed into the various peripherals and modules within the device.
 *
 * Possible clock source modules include internal R/C oscillators, internal
 * DFLL modules, as well as external crystal oscillators and/or clock inputs.
 *
 * \subsection asfdoc_sam0_system_clock_module_overview_cpu_clock CPU / Bus Clocks
 * The CPU and AHB/APBx buses are clocked by the same physical clock source
 * (referred in this module as the Main Clock), however the APBx buses may
 * have additional prescaler division ratios set to give each peripheral bus a
 * different clock speed.
 *
 * The general main clock tree for the CPU and associated buses is shown in
 * \ref asfdoc_sam0_system_clock_module_clock_tree "the figure below".
 *
 * \anchor asfdoc_sam0_system_clock_module_clock_tree
 * \dot
 * digraph overview {
 *   rankdir=LR;
 *   clk_src [label="Clock Sources", shape=none, height=0];
 *   node [label="CPU Bus" shape=ellipse] cpu_bus;
 *   node [label="AHB Bus" shape=ellipse] ahb_bus;
 *   node [label="APBA Bus" shape=ellipse] apb_a_bus;
 *   node [label="APBB Bus" shape=ellipse] apb_b_bus;
 *   node [label="APBC Bus" shape=ellipse] apb_c_bus;
 *   node [label="Main Bus\nPrescaler" shape=square] main_prescaler;
 *   node [label="APBA Bus\nPrescaler" shape=square] apb_a_prescaler;
 *   node [label="APBB Bus\nPrescaler" shape=square] apb_b_prescaler;
 *   node [label="APBC Bus\nPrescaler" shape=square] apb_c_prescaler;
 *   node [label="", shape=polygon, sides=4, distortion=0.6, orientation=90, style=filled, fillcolor=black, height=0.9, width=0.2] main_clock_mux;
 *
 *   clk_src         -> main_clock_mux;
 *   main_clock_mux  -> main_prescaler;
 *   main_prescaler  -> cpu_bus;
 *   main_prescaler  -> ahb_bus;
 *   main_prescaler  -> apb_a_prescaler;
 *   main_prescaler  -> apb_b_prescaler;
 *   main_prescaler  -> apb_c_prescaler;
 *   apb_a_prescaler -> apb_a_bus;
 *   apb_b_prescaler -> apb_b_bus;
 *   apb_c_prescaler -> apb_c_bus;
 * }
 * \enddot
 *
 * \subsection asfdoc_sam0_system_clock_module_overview_clock_masking Clock Masking
 * To save power, the input clock to one or more peripherals on the AHB and APBx
 * buses can be masked away - when masked, no clock is passed into the module.
 * Disabling of clocks of unused modules will prevent all access to the masked
 * module, but will reduce the overall device power consumption.
 *
 * \subsection asfdoc_sam0_system_clock_module_overview_gclk Generic Clocks
 * Within the SAM devices there are a number of Generic Clocks; these are used to
 * provide clocks to the various peripheral clock domains in the device in a
 * standardized manner. One or more master source clocks can be selected as the
 * input clock to a Generic Clock Generator, which can prescale down the input
 * frequency to a slower rate for use in a peripheral.
 *
 * Additionally, a number of individually selectable Generic Clock Channels are
 * provided, which multiplex and gate the various generator outputs for one or
 * more peripherals within the device. This setup allows for a single common
 * generator to feed one or more channels, which can then be enabled or disabled
 * individually as required.
 *
 * \anchor asfdoc_sam0_system_clock_module_chain_overview
 * \dot
 * digraph overview {
 *   rankdir=LR;
 *   node [label="Clock\nSource a" shape=square] system_clock_source;
 *   node [label="Generator 1" shape=square] clock_gen;
 *   node [label="Channel x" shape=square] clock_chan0;
 *   node [label="Channel y" shape=square] clock_chan1;
 *   node [label="Peripheral x" shape=ellipse style=filled fillcolor=lightgray] peripheral0;
 *   node [label="Peripheral y" shape=ellipse style=filled fillcolor=lightgray] peripheral1;
 *
 *   system_clock_source -> clock_gen;
 *   clock_gen   -> clock_chan0;
 *   clock_chan0 -> peripheral0;
 *   clock_gen   -> clock_chan1;
 *   clock_chan1 -> peripheral1;
 * }
 * \enddot
 *
 * \subsubsection asfdoc_sam0_system_clock_module_chain_example Clock Chain Example
 * An example setup of a complete clock chain within the device is shown in
 * \ref asfdoc_sam0_system_clock_module_chain_example_fig "the figure below".
 *
 * \anchor asfdoc_sam0_system_clock_module_chain_example_fig
 * \dot
 * digraph overview {
 *   rankdir=LR;
 *   node [label="External\nOscillator" shape=square] system_clock_source0;
 *   node [label="Generator 0" shape=square] clock_gen0;
 *   node [label="Channel x" shape=square] clock_chan0;
 *   node [label="Core CPU" shape=ellipse  style=filled fillcolor=lightgray] peripheral0;
 *
 *   system_clock_source0 -> clock_gen0;
 *   clock_gen0    -> clock_chan0;
 *   clock_chan0   -> peripheral0;
 *   node [label="8MHz R/C\nOscillator (OSC8M)" shape=square fillcolor=white] system_clock_source1;
 *   node [label="Generator 1" shape=square] clock_gen1;
 *   node [label="Channel y" shape=square] clock_chan1;
 *   node [label="Channel z" shape=square] clock_chan2;
 *   node [label="SERCOM\nModule" shape=ellipse  style=filled fillcolor=lightgray] peripheral1;
 *   node [label="Timer\nModule" shape=ellipse  style=filled fillcolor=lightgray] peripheral2;
 *
 *   system_clock_source1 -> clock_gen1;
 *   clock_gen1    -> clock_chan1;
 *   clock_gen1    -> clock_chan2;
 *   clock_chan1   -> peripheral1;
 *   clock_chan2   -> peripheral2;
 * }
 * \enddot
 *
 * \subsubsection asfdoc_sam0_system_clock_module_overview_gclk_generators Generic Clock Generators
 * Each Generic Clock generator within the device can source its input clock
 * from one of the provided Source Clocks, and prescale the output for one or
 * more Generic Clock Channels in a one-to-many relationship. The generators
 * thus allow for several clocks to be generated of different frequencies,
 * power usages, and accuracies, which can be turned on and off individually to
 * disable the clocks to multiple peripherals as a group.
 *
 * \subsubsection asfdoc_sam0_system_clock_module_overview_gclk_channels Generic Clock Channels
 * To connect a Generic Clock Generator to a peripheral within the
 * device, a Generic Clock Channel is used. Each peripheral or
 * peripheral group has an associated Generic Clock Channel, which serves as the
 * clock input for the peripheral(s). To supply a clock to the peripheral
 * module(s), the associated channel must be connected to a running Generic
 * Clock Generator and the channel enabled.
 *
 * \section asfdoc_sam0_system_clock_special_considerations Special Considerations
 *
 * There are no special considerations for this module.
 *
 *
 * \section asfdoc_sam0_system_clock_extra_info Extra Information
 *
 * For extra information, see \ref asfdoc_sam0_system_clock_extra. This includes:
 *  - \ref asfdoc_sam0_system_clock_extra_acronyms
 *  - \ref asfdoc_sam0_system_clock_extra_dependencies
 *  - \ref asfdoc_sam0_system_clock_extra_errata
 *  - \ref asfdoc_sam0_system_clock_extra_history
 *
 *
 * \section asfdoc_sam0_system_clock_examples Examples
 *
 * For a list of examples related to this driver, see
 * \ref asfdoc_sam0_system_clock_exqsg.
 *
 *
 * \section asfdoc_sam0_system_clock_api_overview API Overview
 * @{
 */

#include <compiler.h>
#include <gclk.h>

/**
 * \name Driver Feature Definition
 * Define system clock features set according to different device family.
 * @{
 */
#if (SAMD21) || (SAMR21) || (SAMD11) || (SAMD10) || (SAMDA1) || defined(__DOXYGEN__)
/** Digital Phase Locked Loop (DPLL) feature support. */
#  define FEATURE_SYSTEM_CLOCK_DPLL
#endif
/*@}*/

/**
 * \brief Available start-up times for the XOSC32K.
 *
 * Available external 32KHz oscillator start-up times, as a number of external
 * clock cycles.
 */
enum system_xosc32k_startup {
    /** Wait zero clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC32K_STARTUP_0,
    /** Wait 32 clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC32K_STARTUP_32,
    /** Wait 2048 clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC32K_STARTUP_2048,
    /** Wait 4096 clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC32K_STARTUP_4096,
    /** Wait 16384 clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC32K_STARTUP_16384,
    /** Wait 32768 clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC32K_STARTUP_32768,
    /** Wait 65536 clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC32K_STARTUP_65536,
    /** Wait 131072 clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC32K_STARTUP_131072,
};

/**
 * \brief Available start-up times for the XOSC.
 *
 * Available external oscillator start-up times, as a number of external clock
 * cycles.
 */
enum system_xosc_startup {
    /** Wait one clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC_STARTUP_1,
    /** Wait two clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC_STARTUP_2,
    /** Wait four clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC_STARTUP_4,
    /** Wait eight clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC_STARTUP_8,
    /** Wait 16 clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC_STARTUP_16,
    /** Wait 32 clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC_STARTUP_32,
    /** Wait 64 clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC_STARTUP_64,
    /** Wait 128 clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC_STARTUP_128,
    /** Wait 256 clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC_STARTUP_256,
    /** Wait 512 clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC_STARTUP_512,
    /** Wait 1024 clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC_STARTUP_1024,
    /** Wait 2048 clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC_STARTUP_2048,
    /** Wait 4096 clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC_STARTUP_4096,
    /** Wait 8192 clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC_STARTUP_8192,
    /** Wait 16384 clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC_STARTUP_16384,
    /** Wait 32768 clock cycles until the clock source is considered stable. */
    SYSTEM_XOSC_STARTUP_32768,
};

/**
 * \brief Available start-up times for the OSC32K.
 *
 * Available internal 32KHz oscillator start-up times, as a number of internal
 * OSC32K clock cycles.
 */
enum system_osc32k_startup {
    /** Wait three clock cycles until the clock source is considered stable. */
    SYSTEM_OSC32K_STARTUP_3,
    /** Wait four clock cycles until the clock source is considered stable. */
    SYSTEM_OSC32K_STARTUP_4,
    /** Wait six clock cycles until the clock source is considered stable. */
    SYSTEM_OSC32K_STARTUP_6,
    /** Wait ten clock cycles until the clock source is considered stable. */
    SYSTEM_OSC32K_STARTUP_10,
    /** Wait 18 clock cycles until the clock source is considered stable. */
    SYSTEM_OSC32K_STARTUP_18,
    /** Wait 34 clock cycles until the clock source is considered stable */
    SYSTEM_OSC32K_STARTUP_34,
    /** Wait 66 clock cycles until the clock source is considered stable. */
    SYSTEM_OSC32K_STARTUP_66,
    /** Wait 130 clock cycles until the clock source is considered stable. */
    SYSTEM_OSC32K_STARTUP_130,
};

/**
 * \brief Division prescalers for the internal 8MHz system clock.
 *
 * Available prescalers for the internal 8MHz (nominal) system clock.
 */
enum system_osc8m_div {
    /** Do not divide the 8MHz RC oscillator output. */
    SYSTEM_OSC8M_DIV_1,
    /** Divide the 8MHz RC oscillator output by two. */
    SYSTEM_OSC8M_DIV_2,
    /** Divide the 8MHz RC oscillator output by four. */
    SYSTEM_OSC8M_DIV_4,
    /** Divide the 8MHz RC oscillator output by eight. */
    SYSTEM_OSC8M_DIV_8,
};

/**
 * \brief Frequency range for the internal 8MHz RC oscillator.
 *
 * Internal 8MHz RC oscillator frequency range setting
 */
enum system_osc8m_frequency_range {
    /** Frequency range 4MHz to 6MHz. */
    SYSTEM_OSC8M_FREQUENCY_RANGE_4_TO_6,
    /** Frequency range 6MHz to 8MHz. */
    SYSTEM_OSC8M_FREQUENCY_RANGE_6_TO_8,
    /** Frequency range 8MHz to 11MHz. */
    SYSTEM_OSC8M_FREQUENCY_RANGE_8_TO_11,
    /** Frequency range 11MHz to 15MHz. */
    SYSTEM_OSC8M_FREQUENCY_RANGE_11_TO_15,
};

/**
 * \brief Main CPU and APB/AHB bus clock source prescaler values.
 *
 * Available division ratios for the CPU and APB/AHB bus clocks.
 */
enum system_main_clock_div {
    /** Divide Main clock by one. */
    SYSTEM_MAIN_CLOCK_DIV_1,
    /** Divide Main clock by two. */
    SYSTEM_MAIN_CLOCK_DIV_2,
    /** Divide Main clock by four. */
    SYSTEM_MAIN_CLOCK_DIV_4,
    /** Divide Main clock by eight. */
    SYSTEM_MAIN_CLOCK_DIV_8,
    /** Divide Main clock by 16. */
    SYSTEM_MAIN_CLOCK_DIV_16,
    /** Divide Main clock by 32. */
    SYSTEM_MAIN_CLOCK_DIV_32,
    /** Divide Main clock by 64. */
    SYSTEM_MAIN_CLOCK_DIV_64,
    /** Divide Main clock by 128. */
    SYSTEM_MAIN_CLOCK_DIV_128,
};

/**
 * \brief External clock source types.
 *
 * Available external clock source types.
 */
enum system_clock_external {
    /** The external clock source is a crystal oscillator. */
    SYSTEM_CLOCK_EXTERNAL_CRYSTAL,
    /** The connected clock source is an external logic level clock signal. */
    SYSTEM_CLOCK_EXTERNAL_CLOCK,
};

/**
 * \brief Operating modes of the DFLL clock source.
 *
 * Available operating modes of the DFLL clock source module.
 */
enum system_clock_dfll_loop_mode {
    /** The DFLL is operating in open loop mode with no feedback. */
    SYSTEM_CLOCK_DFLL_LOOP_MODE_OPEN,
    /** The DFLL is operating in closed loop mode with frequency feedback from
     *  a low frequency reference clock.
     */
    SYSTEM_CLOCK_DFLL_LOOP_MODE_CLOSED = SYSCTRL_DFLLCTRL_MODE,

#ifdef SYSCTRL_DFLLCTRL_USBCRM
    /** The DFLL is operating in USB recovery mode with frequency feedback
     *  from USB SOF.
     */
    SYSTEM_CLOCK_DFLL_LOOP_MODE_USB_RECOVERY = SYSCTRL_DFLLCTRL_USBCRM,
#endif
};

/**
 * \brief Locking behavior for the DFLL during device wake-up.
 *
 * DFLL lock behavior modes on device wake-up from sleep.
 */
enum system_clock_dfll_wakeup_lock {
    /** Keep DFLL lock when the device wakes from sleep. */
    SYSTEM_CLOCK_DFLL_WAKEUP_LOCK_KEEP,
    /** Lose DFLL lock when the devices wakes from sleep. */
    SYSTEM_CLOCK_DFLL_WAKEUP_LOCK_LOSE = SYSCTRL_DFLLCTRL_LLAW,
};

/**
 * \brief Fine tracking behavior for the DFLL once a lock has been acquired.
 *
 * DFLL fine tracking behavior modes after a lock has been acquired.
 */
enum system_clock_dfll_stable_tracking {
    /** Keep tracking after the DFLL has gotten a fine lock. */
    SYSTEM_CLOCK_DFLL_STABLE_TRACKING_TRACK_AFTER_LOCK,
    /** Stop tracking after the DFLL has gotten a fine lock. */
    SYSTEM_CLOCK_DFLL_STABLE_TRACKING_FIX_AFTER_LOCK = SYSCTRL_DFLLCTRL_STABLE,
};

/**
 * \brief Chill-cycle behavior of the DFLL module.
 *
 * DFLL chill-cycle behavior modes of the DFLL module. A chill cycle is a period
 * of time when the DFLL output frequency is not measured by the unit, to allow
 * the output to stabilize after a change in the input clock source.
 */
enum system_clock_dfll_chill_cycle {
    /** Enable a chill cycle, where the DFLL output frequency is not measured. */
    SYSTEM_CLOCK_DFLL_CHILL_CYCLE_ENABLE,
    /** Disable a chill cycle, where the DFLL output frequency is not measured. */
    SYSTEM_CLOCK_DFLL_CHILL_CYCLE_DISABLE = SYSCTRL_DFLLCTRL_CCDIS,
};

/**
 * \brief QuickLock settings for the DFLL module.
 *
 * DFLL QuickLock settings for the DFLL module, to allow for a faster lock of
 * the DFLL output frequency at the expense of accuracy.
 */
enum system_clock_dfll_quick_lock {
    /** Enable the QuickLock feature for looser lock requirements on the DFLL. */
    SYSTEM_CLOCK_DFLL_QUICK_LOCK_ENABLE,
    /** Disable the QuickLock feature for strict lock requirements on the DFLL. */
    SYSTEM_CLOCK_DFLL_QUICK_LOCK_DISABLE = SYSCTRL_DFLLCTRL_QLDIS,
};

/**
 * \brief Available clock sources in the system.
 *
 * Clock sources available to the GCLK generators.
 */
enum system_clock_source {
    /** Internal 8MHz RC oscillator. */
    SYSTEM_CLOCK_SOURCE_OSC8M    = GCLK_SOURCE_OSC8M,
    /** Internal 32KHz RC oscillator. */
    SYSTEM_CLOCK_SOURCE_OSC32K   = GCLK_SOURCE_OSC32K,
    /** External oscillator. */
    SYSTEM_CLOCK_SOURCE_XOSC     = GCLK_SOURCE_XOSC ,
    /** External 32KHz oscillator. */
    SYSTEM_CLOCK_SOURCE_XOSC32K  = GCLK_SOURCE_XOSC32K,
    /** Digital Frequency Locked Loop (DFLL). */
    SYSTEM_CLOCK_SOURCE_DFLL     = GCLK_SOURCE_DFLL48M,
    /** Internal Ultra Low Power 32KHz oscillator. */
    SYSTEM_CLOCK_SOURCE_ULP32K   = GCLK_SOURCE_OSCULP32K,
    /** Generator input pad. */
    SYSTEM_CLOCK_SOURCE_GCLKIN     = GCLK_SOURCE_GCLKIN,
    /** Generic clock generator one output. */
    SYSTEM_CLOCK_SOURCE_GCLKGEN1   = GCLK_SOURCE_GCLKGEN1,
#ifdef FEATURE_SYSTEM_CLOCK_DPLL
    /** Digital Phase Locked Loop (DPLL).
     * Check \c FEATURE_SYSTEM_CLOCK_DPLL for which device support it.
     */
    SYSTEM_CLOCK_SOURCE_DPLL     = GCLK_SOURCE_FDPLL,
#endif
};

/**
 * \brief List of APB peripheral buses.
 *
 * Available bus clock domains on the APB bus.
 */
enum system_clock_apb_bus {
    /** Peripheral bus A on the APB bus. */
    SYSTEM_CLOCK_APB_APBA,
    /** Peripheral bus B on the APB bus. */
    SYSTEM_CLOCK_APB_APBB,
    /** Peripheral bus C on the APB bus. */
    SYSTEM_CLOCK_APB_APBC,
};

/**
 * \brief Configuration structure for XOSC.
 *
 * External oscillator clock configuration structure.
 */
struct system_clock_source_xosc_config {
    /** External clock type. */
    enum system_clock_external external_clock;
    /** Crystal oscillator start-up time. */
    enum system_xosc_startup startup_time;
    /** Enable automatic amplitude gain control. */
    bool auto_gain_control;
    /** External clock/crystal frequency. */
    uint32_t frequency;
    /** Keep the XOSC enabled in standby sleep mode. */
    bool run_in_standby;
    /** Run On Demand. If this is set the XOSC won't run
     * until requested by a peripheral. */
    bool on_demand;
};

/**
 * \brief Configuration structure for XOSC32K.
 *
 * External 32KHz oscillator clock configuration structure.
 */
struct system_clock_source_xosc32k_config {
    /** External clock type. */
    enum system_clock_external external_clock;
    /** Crystal oscillator start-up time. */
    enum system_xosc32k_startup startup_time;
    /** Enable automatic amplitude control. */
    bool auto_gain_control;
    /** Enable 1KHz output. */
    bool enable_1khz_output;
    /** Enable 32KHz output. */
    bool enable_32khz_output;
    /** External clock/crystal frequency. */
    uint32_t frequency;
    /** Keep the XOSC32K enabled in standby sleep mode. */
    bool run_in_standby;
    /** Run On Demand. If this is set the XOSC32K won't run
     * until requested by a peripheral. */
    bool on_demand;
    /** Lock configuration after it has been written,
     *  a device reset will release the lock. */
    bool write_once;
};

/**
 * \brief Configuration structure for OSC8M.
 *
 * Internal 8MHz (nominal) oscillator configuration structure.
 */
struct system_clock_source_osc8m_config {
    /** Internal 8MHz RC oscillator prescaler. */
    enum system_osc8m_div prescaler;
    /** Keep the OSC8M enabled in standby sleep mode. */
    bool run_in_standby;
    /** Run On Demand. If this is set the OSC8M won't run
     * until requested by a peripheral. */
    bool on_demand;
};

/**
 * \brief Configuration structure for OSC32K.
 *
 * Internal 32KHz (nominal) oscillator configuration structure.
 */
struct system_clock_source_osc32k_config {
    /** Startup time. */
    enum system_osc32k_startup startup_time;
    /** Enable 1KHz output. */
    bool enable_1khz_output;
    /** Enable 32KHz output. */
    bool enable_32khz_output;
    /** Keep the OSC32K enabled in standby sleep mode. */
    bool run_in_standby;
    /** Run On Demand. If this is set the OSC32K won't run
     * until requested by a peripheral. */
    bool on_demand;
    /** Lock configuration after it has been written,
     *  a device reset will release the lock. */
    bool write_once;
};

/**
 * \brief Configuration structure for DFLL.
 *
 * DFLL oscillator configuration structure.
 */
struct system_clock_source_dfll_config {
    /** Loop mode. */
    enum system_clock_dfll_loop_mode loop_mode;
    /** Run On Demand. If this is set the DFLL won't run
     * until requested by a peripheral. */
    bool on_demand;
    /** Enable Quick Lock. */
    enum system_clock_dfll_quick_lock quick_lock;
    /** Enable Chill Cycle. */
    enum system_clock_dfll_chill_cycle chill_cycle;
    /** DFLL lock state on wakeup. */
    enum system_clock_dfll_wakeup_lock wakeup_lock;
    /** DFLL tracking after fine lock. */
    enum system_clock_dfll_stable_tracking stable_tracking;
    /** Coarse calibration value (Open loop mode). */
    uint8_t coarse_value;
    /** Fine calibration value (Open loop mode). */
    uint16_t fine_value;
    /** Coarse adjustment maximum step size (Closed loop mode). */
    uint8_t coarse_max_step;
    /** Fine adjustment maximum step size (Closed loop mode). */
    uint16_t fine_max_step;
    /** DFLL multiply factor (Closed loop mode. */
    uint16_t multiply_factor;
};

/**
 * \name External Oscillator Management
 * @{
 */

/**
 * \brief Retrieve the default configuration for XOSC.
 *
 * Fills a configuration structure with the default configuration for an
 * external oscillator module:
 *   - External Crystal
 *   - Start-up time of 16384 external clock cycles
 *   - Automatic crystal gain control mode enabled
 *   - Frequency of 12MHz
 *   - Don't run in STANDBY sleep mode
 *   - Run only when requested by peripheral (on demand)
 *
 * \param[out] config  Configuration structure to fill with default values
 */
static inline void system_clock_source_xosc_get_config_defaults(
    struct system_clock_source_xosc_config *const config)
{
    Assert(config);

    config->external_clock    = SYSTEM_CLOCK_EXTERNAL_CRYSTAL;
    config->startup_time      = SYSTEM_XOSC_STARTUP_16384;
    config->auto_gain_control = true;
    config->frequency         = 12000000UL;
    config->run_in_standby    = false;
    config->on_demand         = true;
}

void system_clock_source_xosc_set_config(
    struct system_clock_source_xosc_config *const config);

/**
 * @}
 */


/**
 * \name External 32KHz Oscillator Management
 * @{
 */

/**
 * \brief Retrieve the default configuration for XOSC32K.
 *
 * Fills a configuration structure with the default configuration for an
 * external 32KHz oscillator module:
 *   - External Crystal
 *   - Start-up time of 16384 external clock cycles
 *   - Automatic crystal gain control mode disabled
 *   - Frequency of 32.768KHz
 *   - 1KHz clock output disabled
 *   - 32KHz clock output enabled
 *   - Don't run in STANDBY sleep mode
 *   - Run only when requested by peripheral (on demand)
 *   - Don't lock registers after configuration has been written
 *
 * \param[out] config  Configuration structure to fill with default values
 */
static inline void system_clock_source_xosc32k_get_config_defaults(
    struct system_clock_source_xosc32k_config *const config)
{
    Assert(config);

    config->external_clock      = SYSTEM_CLOCK_EXTERNAL_CRYSTAL;
    config->startup_time        = SYSTEM_XOSC32K_STARTUP_16384;
    config->auto_gain_control   = false;
    config->frequency           = 32768UL;
    config->enable_1khz_output  = false;
    config->enable_32khz_output = true;
    config->run_in_standby      = false;
    config->on_demand           = true;
    config->write_once          = false;
}

void system_clock_source_xosc32k_set_config(
    struct system_clock_source_xosc32k_config *const config);
/**
 * @}
 */


/**
 * \name Internal 32KHz Oscillator Management
 * @{
 */

/**
 * \brief Retrieve the default configuration for OSC32K.
 *
 * Fills a configuration structure with the default configuration for an
 * internal 32KHz oscillator module:
 *   - 1KHz clock output enabled
 *   - 32KHz clock output enabled
 *   - Don't run in STANDBY sleep mode
 *   - Run only when requested by peripheral (on demand)
 *   - Set startup time to 130 cycles
 *   - Don't lock registers after configuration has been written
 *
 * \param[out] config  Configuration structure to fill with default values
 */
static inline void system_clock_source_osc32k_get_config_defaults(
    struct system_clock_source_osc32k_config *const config)
{
    Assert(config);

    config->enable_1khz_output  = true;
    config->enable_32khz_output = true;
    config->run_in_standby      = false;
    config->on_demand           = true;
    config->startup_time        = SYSTEM_OSC32K_STARTUP_130;
    config->write_once          = false;
}

void system_clock_source_osc32k_set_config(
    struct system_clock_source_osc32k_config *const config);

/**
 * @}
 */


/**
 * \name Internal 8MHz Oscillator Management
 * @{
 */

/**
 * \brief Retrieve the default configuration for OSC8M.
 *
 * Fills a configuration structure with the default configuration for an
 * internal 8MHz (nominal) oscillator module:
 *   - Clock output frequency divided by a factor of eight
 *   - Don't run in STANDBY sleep mode
 *   - Run only when requested by peripheral (on demand)
 *
 * \param[out] config  Configuration structure to fill with default values
 */
static inline void system_clock_source_osc8m_get_config_defaults(
    struct system_clock_source_osc8m_config *const config)
{
    Assert(config);

    config->prescaler       = SYSTEM_OSC8M_DIV_8;
    config->run_in_standby  = false;
    config->on_demand       = true;
}

void system_clock_source_osc8m_set_config(
    struct system_clock_source_osc8m_config *const config);

/**
 * @}
 */


/**
 * \name Internal DFLL Management
 * @{
 */

/**
 * \brief Retrieve the default configuration for DFLL.
 *
 * Fills a configuration structure with the default configuration for a
 * DFLL oscillator module:
 *   - Open loop mode
 *   - QuickLock mode enabled
 *   - Chill cycle enabled
 *   - Output frequency lock maintained during device wake-up
 *   - Continuous tracking of the output frequency
 *   - Default tracking values at the mid-points for both coarse and fine
 *     tracking parameters
 *   - Don't run in STANDBY sleep mode
 *   - Run only when requested by peripheral (on demand)
 *
 * \param[out] config  Configuration structure to fill with default values
 */
static inline void system_clock_source_dfll_get_config_defaults(
    struct system_clock_source_dfll_config *const config)
{
    Assert(config);

    config->loop_mode       = SYSTEM_CLOCK_DFLL_LOOP_MODE_OPEN;
    config->quick_lock      = SYSTEM_CLOCK_DFLL_QUICK_LOCK_ENABLE;
    config->chill_cycle     = SYSTEM_CLOCK_DFLL_CHILL_CYCLE_ENABLE;
    config->wakeup_lock     = SYSTEM_CLOCK_DFLL_WAKEUP_LOCK_KEEP;
    config->stable_tracking = SYSTEM_CLOCK_DFLL_STABLE_TRACKING_TRACK_AFTER_LOCK;
    config->on_demand       = true;

    /* Open loop mode calibration value */
    config->coarse_value    = 0x1f / 4; /* Midpoint */
    config->fine_value      = 0xff / 4; /* Midpoint */

    /* Closed loop mode */
    config->coarse_max_step = 1;
    config->fine_max_step   = 1;
    config->multiply_factor = 6; /* Multiply 8MHz by 6 to get 48MHz */
}

void system_clock_source_dfll_set_config(
    struct system_clock_source_dfll_config *const config);

/**
 * @}
 */

/**
 * \name Clock Source Management
 * @{
 */
enum status_code system_clock_source_write_calibration(
    const enum system_clock_source system_clock_source,
    const uint16_t calibration_value,
    const uint8_t freq_range);

enum status_code system_clock_source_enable(
    const enum system_clock_source system_clock_source);

enum status_code system_clock_source_disable(
    const enum system_clock_source clk_source);

bool system_clock_source_is_ready(
    const enum system_clock_source clk_source);

uint32_t system_clock_source_get_hz(
    const enum system_clock_source clk_source);

/**
 * @}
 */

/**
 * \name Main Clock Management
 * @{
 */

/**
 * \brief Set main CPU clock divider.
 *
 * Sets the clock divider used on the main clock to provide the CPU clock.
 *
 * \param[in] divider  CPU clock divider to set
 */
static inline void system_cpu_clock_set_divider(
    const enum system_main_clock_div divider)
{
    Assert(((uint32_t)divider & PM_CPUSEL_CPUDIV_Msk) == divider);
    PM->CPUSEL.reg = (uint32_t)divider;
}

/**
 * \brief Retrieves the current frequency of the CPU core.
 *
 * Retrieves the operating frequency of the CPU core, obtained from the main
 * generic clock and the set CPU bus divider.
 *
 * \return Current CPU frequency in Hz.
 */
static inline uint32_t system_cpu_clock_get_hz(void)
{
    return (system_gclk_gen_get_hz(GCLK_GENERATOR_0) >> PM->CPUSEL.reg);
}

/**
 * \brief Set APBx clock divider.
 *
 * Set the clock divider used on the main clock to provide the clock for the
 * given APBx bus.
 *
 * \param[in] divider  APBx bus divider to set
 * \param[in] bus      APBx bus to set divider
 *
 * \returns Status of the clock division change operation.
 *
 * \retval STATUS_ERR_INVALID_ARG  Invalid bus ID was given
 * \retval STATUS_OK               The APBx clock was set successfully
 */
static inline enum status_code system_apb_clock_set_divider(
    const enum system_clock_apb_bus bus,
    const enum system_main_clock_div divider)
{
    switch (bus) {
        case SYSTEM_CLOCK_APB_APBA:
                    PM->APBASEL.reg = (uint32_t)divider;
                break;
            case SYSTEM_CLOCK_APB_APBB:
                PM->APBBSEL.reg = (uint32_t)divider;
                break;
            case SYSTEM_CLOCK_APB_APBC:
                PM->APBCSEL.reg = (uint32_t)divider;
                break;
            default:
                Assert(false);
                return STATUS_ERR_INVALID_ARG;
        }

        return STATUS_OK;
    }

    /**
     * \brief Retrieves the current frequency of a ABPx.
     *
     * Retrieves the operating frequency of an APBx bus, obtained from the main
     * generic clock and the set APBx bus divider.
     *
     * \return Current APBx bus frequency in Hz.
     */
    static inline uint32_t system_apb_clock_get_hz(
        const enum system_clock_apb_bus bus)
{
    uint16_t bus_divider = 0;

    switch (bus) {
        case SYSTEM_CLOCK_APB_APBA:
            bus_divider = PM->APBASEL.reg;
            break;
        case SYSTEM_CLOCK_APB_APBB:
            bus_divider = PM->APBBSEL.reg;
            break;
        case SYSTEM_CLOCK_APB_APBC:
            bus_divider = PM->APBCSEL.reg;
            break;
        default:
            Assert(false);
            return 0;
    }

    return (system_gclk_gen_get_hz(GCLK_GENERATOR_0) >> bus_divider);
}


/**
 * @}
 */

/**
 * \name Bus Clock Masking
 * @{
 */

/**
 * \brief Set bits in the clock mask for the AHB bus.
 *
 * This function will set bits in the clock mask for the AHB bus.
 * Any bits set to 1 will enable that clock, 0 bits in the mask
 * will be ignored.
 *
 * \param[in] ahb_mask  AHB clock mask to enable
 */
static inline void system_ahb_clock_set_mask(
    const uint32_t ahb_mask)
{
    PM->AHBMASK.reg |= ahb_mask;
}

/**
 * \brief Clear bits in the clock mask for the AHB bus.
 *
 * This function will clear bits in the clock mask for the AHB bus.
 * Any bits set to 1 will disable that clock, 0 bits in the mask
 * will be ignored.
 *
 * \param[in] ahb_mask  AHB clock mask to disable
 */
static inline void system_ahb_clock_clear_mask(
    const uint32_t ahb_mask)
{
    PM->AHBMASK.reg &= ~ahb_mask;
}

/**
 * \brief Set bits in the clock mask for an APBx bus.
 *
 * This function will set bits in the clock mask for an APBx bus.
 * Any bits set to 1 will enable the corresponding module clock, zero bits in
 * the mask will be ignored.
 *
 * \param[in] mask  APBx clock mask, a \c SYSTEM_CLOCK_APB_APBx constant from
 *                  the device header files
 * \param[in] bus   Bus to set clock mask bits for, a mask of \c PM_APBxMASK_*
 *                  constants from the device header files
 *
 * \returns Status indicating the result of the clock mask change operation.
 *
 * \retval STATUS_ERR_INVALID_ARG  Invalid bus given
 * \retval STATUS_OK               The clock mask was set successfully
 */
static inline enum status_code system_apb_clock_set_mask(
    const enum system_clock_apb_bus bus,
    const uint32_t mask)
{
    switch (bus) {
        case SYSTEM_CLOCK_APB_APBA:
                    PM->APBAMASK.reg |= mask;
                break;

            case SYSTEM_CLOCK_APB_APBB:
                PM->APBBMASK.reg |= mask;
                break;

            case SYSTEM_CLOCK_APB_APBC:
                PM->APBCMASK.reg |= mask;
                break;

            default:
                Assert(false);
                return STATUS_ERR_INVALID_ARG;

        }

        return STATUS_OK;
    }

    /**
     * \brief Clear bits in the clock mask for an APBx bus.
     *
     * This function will clear bits in the clock mask for an APBx bus.
     * Any bits set to 1 will disable the corresponding module clock, zero bits in
     * the mask will be ignored.
     *
     * \param[in] mask  APBx clock mask, a \c SYSTEM_CLOCK_APB_APBx constant from
     *                  the device header files
     * \param[in] bus   Bus to clear clock mask bits
     *
     * \returns Status indicating the result of the clock mask change operation.
     *
     * \retval STATUS_ERR_INVALID_ARG  Invalid bus ID was given
     * \retval STATUS_OK               The clock mask was changed successfully
     */
    static inline enum status_code system_apb_clock_clear_mask(
        const enum system_clock_apb_bus bus,
        const uint32_t mask)
{
    switch (bus) {
        case SYSTEM_CLOCK_APB_APBA:
                    PM->APBAMASK.reg &= ~mask;
                break;

            case SYSTEM_CLOCK_APB_APBB:
                PM->APBBMASK.reg &= ~mask;
                break;

            case SYSTEM_CLOCK_APB_APBC:
                PM->APBCMASK.reg &= ~mask;
                break;

            default:
                Assert(false);
                return STATUS_ERR_INVALID_ARG;
        }

        return STATUS_OK;
    }

    /**
     * @}
     */

#ifdef FEATURE_SYSTEM_CLOCK_DPLL
    /**
     * \brief Reference clock source of the DPLL module.
     */
    enum system_clock_source_dpll_reference_clock {
    /** Select XOSC32K as clock reference. */
    SYSTEM_CLOCK_SOURCE_DPLL_REFERENCE_CLOCK_XOSC32K,
    /** Select XOSC as clock reference. */
    SYSTEM_CLOCK_SOURCE_DPLL_REFERENCE_CLOCK_XOSC,
    /** Select GCLK as clock reference. */
    SYSTEM_CLOCK_SOURCE_DPLL_REFERENCE_CLOCK_GCLK,
};

/**
 * \brief Lock time-out value of the DPLL module.
 */
enum system_clock_source_dpll_lock_time {
    /** Set no time-out as default. */
    SYSTEM_CLOCK_SOURCE_DPLL_LOCK_TIME_DEFAULT,
    /** Set time-out if no lock within 8ms. */
    SYSTEM_CLOCK_SOURCE_DPLL_LOCK_TIME_8MS = 0x04,
    /** Set time-out if no lock within 9ms. */
    SYSTEM_CLOCK_SOURCE_DPLL_LOCK_TIME_9MS,
    /** Set time-out if no lock within 10ms. */
    SYSTEM_CLOCK_SOURCE_DPLL_LOCK_TIME_10MS,
    /** Set time-out if no lock within 11ms. */
    SYSTEM_CLOCK_SOURCE_DPLL_LOCK_TIME_11MS,
};

/**
 * \brief Filter type of the DPLL module.
 */
enum system_clock_source_dpll_filter {
    /** Default filter mode. */
    SYSTEM_CLOCK_SOURCE_DPLL_FILTER_DEFAULT,
    /** Low bandwidth filter. */
    SYSTEM_CLOCK_SOURCE_DPLL_FILTER_LOW_BANDWIDTH_FILTER,
    /** High bandwidth filter. */
    SYSTEM_CLOCK_SOURCE_DPLL_FILTER_HIGH_BANDWIDTH_FILTER,
    /** High damping filter. */
    SYSTEM_CLOCK_SOURCE_DPLL_FILTER_HIGH_DAMPING_FILTER,
};

/**
 * \brief Configuration structure for DPLL.
 *
 * DPLL oscillator configuration structure.
 */
struct system_clock_source_dpll_config {
    /** Run On Demand. If this is set the DPLL won't run
     * until requested by a peripheral. */
    bool on_demand;
    /** Keep the DPLL enabled in standby sleep mode. */
    bool run_in_standby;
    /** Bypass lock signal. */
    bool lock_bypass;
    /** Wake up fast. If this is set DPLL output clock is enabled after
     * the startup time. */
    bool wake_up_fast;
    /** Enable low power mode.  */
    bool low_power_enable;

    /** Output frequency of the clock. */
    uint32_t output_frequency;
    /** Reference frequency of the clock. */
    uint32_t reference_frequency;
    /** Devider of reference clock. */
    uint16_t reference_divider;

    /** Filter type of the DPLL module. */
    enum system_clock_source_dpll_filter          filter;
    /** Lock time-out value of the DPLL module. */
    enum system_clock_source_dpll_lock_time       lock_time;
    /** Reference clock source of the DPLL module. */
    enum system_clock_source_dpll_reference_clock reference_clock;
};

/**
 * \name Internal DPLL Management
 * @{
 */

/**
 * \brief Retrieve the default configuration for DPLL.
 *
 * Fills a configuration structure with the default configuration for a
 * DPLL oscillator module:
 *   - Run only when requested by peripheral (on demand)
 *   - Don't run in STANDBY sleep mode
 *   - Lock bypass disabled
 *   - Fast wake up disabled
 *   - Low power mode disabled
 *   - Output frequency is 48MHz
 *   - Reference clock frequency is 32768Hz
 *   - Not divide reference clock
 *   - Select REF0 as reference clock
 *   - Set lock time to default mode
 *   - Use default filter
 *
 * \param[out] config  Configuration structure to fill with default values
 */
static inline void system_clock_source_dpll_get_config_defaults(
    struct system_clock_source_dpll_config *const config)
{
    config->on_demand           = true;
    config->run_in_standby      = false;
    config->lock_bypass         = false;
    config->wake_up_fast        = false;
    config->low_power_enable    = false;

    config->output_frequency    = 48000000;
    config->reference_frequency = 32768;
    config->reference_divider   = 1;
    config->reference_clock     = SYSTEM_CLOCK_SOURCE_DPLL_REFERENCE_CLOCK_XOSC32K;

    config->lock_time           = SYSTEM_CLOCK_SOURCE_DPLL_LOCK_TIME_DEFAULT;
    config->filter              = SYSTEM_CLOCK_SOURCE_DPLL_FILTER_DEFAULT;
};

void system_clock_source_dpll_set_config(
    struct system_clock_source_dpll_config *const config);

/* @} */
#endif

/**
 * \name System Clock Initialization
 * @{
 */

void system_clock_init(void);

/**
 * @}
 */

/**
 * \name System Flash Wait States
 * @{
 */

/**
 * \brief Set flash controller wait states.
 *
 * Will set the number of wait states that are used by the onboard
 * flash memory. The number of wait states depend on both device
 * supply voltage and CPU speed. The required number of wait states
 * can be found in the electrical characteristics of the device.
 *
 * \param[in] wait_states Number of wait states to use for internal flash
 */
static inline void system_flash_set_waitstates(uint8_t wait_states)
{
    Assert(NVMCTRL_CTRLB_RWS((uint32_t)wait_states) ==
           ((uint32_t)wait_states << NVMCTRL_CTRLB_RWS_Pos));

    NVMCTRL->CTRLB.bit.RWS = wait_states;
}
/**
 * @}
 */

/**
 * @}
 */

/**
 * \page asfdoc_sam0_system_clock_extra Extra Information for SYSTEM CLOCK Driver
 *
 * \section asfdoc_sam0_system_clock_extra_acronyms Acronyms
 * Below is a table listing the acronyms used in this module, along with their
 * intended meanings.
 *
 * <table>
 *	<tr>
 *		<th>Acronym</th>
 *		<th>Description</th>
 *	</tr>
 *	<tr>
 *		<td>DFLL</td>
 *		<td>Digital Frequency Locked Loop</td>
 *	</tr>
 *	<tr>
 *		<td>MUX</td>
 *		<td>Multiplexer</td>
 *	</tr>
 *	<tr>
 *		<td>OSC32K</td>
 *		<td>Internal 32KHz Oscillator</td>
 *	</tr>
 *	<tr>
 *		<td>OSC8M</td>
 *		<td>Internal 8MHz Oscillator</td>
 *	</tr>
 *	<tr>
 *		<td>PLL</td>
 *		<td>Phase Locked Loop</td>
 *	</tr>
 *	<tr>
 *		<td>OSC</td>
 *		<td>Oscillator</td>
 *	</tr>
 *	<tr>
 *		<td>XOSC</td>
 *		<td>External Oscillator</td>
 *	</tr>
 *	<tr>
 *		<td>XOSC32K</td>
 *		<td>External 32KHz Oscillator</td>
 *	</tr>
 *	<tr>
 *		<td>AHB</td>
 *		<td>Advanced High-performance Bus</td>
 *	</tr>
 *	<tr>
 *		<td>APB</td>
 *		<td>Advanced Peripheral Bus</td>
 *	</tr>
 *	<tr>
 *		<td>DPLL</td>
 *		<td>Digital Phase Locked Loop</td>
 *	</tr>
 * </table>
 *
 *
 * \section asfdoc_sam0_system_clock_extra_dependencies Dependencies
 * This driver has the following dependencies:
 *
 *  - None
 *
 *
 * \section asfdoc_sam0_system_clock_extra_errata Errata
 *
 *	- This driver implements experimental workaround for errata 9905
 *
 *	  "The DFLL clock must be requested before being configured otherwise a
 *	  write access to a DFLL register can freeze the device."
 *	  This driver will enable and configure the DFLL before the ONDEMAND bit is set.
 *
 *
 * \section asfdoc_sam0_system_clock_extra_history Module History
 * An overview of the module history is presented in the table below, with
 * details on the enhancements and fixes made to the module since its first
 * release. The current version of this corresponds to the newest version in
 * the table.
 *
 * <table>
 *	<tr>
 *		<th>Changelog</th>
 *	</tr>
 *	<tr>
 *		<td>
 *			\li Corrected OSC32K startup time definitions
 *			\li Support locking of OSC32K and XOSC32K config register (default: false)
 *			\li Added DPLL support, functions added:
 *			    \c system_clock_source_dpll_get_config_defaults() and
 *		        \c system_clock_source_dpll_set_config()
 *			\li Moved gclk channel locking feature out of the config struct
 *			    functions added:
 *			    \c system_gclk_chan_lock(),
 *			    \c system_gclk_chan_is_locked()
 *			    \c system_gclk_chan_is_enabled() and
 *			    \c system_gclk_gen_is_enabled()
 *		</td>
 *	</tr>
 *  <tr>
 *		<td>Fixed \c system_gclk_chan_disable() deadlocking if a channel is enabled
 *		    and configured to a failed/not running clock generator</td>
 *  </tr>
 *	<tr>
 *		<td>
 *			\li Changed default value for CONF_CLOCK_DFLL_ON_DEMAND from \c true to \c false
 *			\li Fixed system_flash_set_waitstates() failing with an assertion
 *			    if an odd number of wait states provided
 *		</td>
 *	</tr>
 *	<tr>
 *		<td>
 *			\li Updated dfll configuration function to implement workaround for
 *			    errata 9905 in the DFLL module
 *			\li Updated \c system_clock_init() to reset interrupt flags before
 *			    they are used
 *			\li Fixed \c system_clock_source_get_hz() to return correcy DFLL
 *			    frequency number
 *		</td>
 *	</tr>
 *	<tr>
 *		<td>\li Fixed \c system_clock_source_is_ready not returning the correct
 *              state for \c SYSTEM_CLOCK_SOURCE_OSC8M
 *          \li Renamed the various \c system_clock_source_*_get_default_config()
 *              functions to \c system_clock_source_*_get_config_defaults() to
 *              match the remainder of ASF
 *          \li Added OSC8M calibration constant loading from the device signature
 *              row when the oscillator is initialized
 *          \li Updated default configuration of the XOSC32 to disable Automatic
 *              Gain Control due to silicon errata
 *      </td>
 *	</tr>
 *	<tr>
 *		<td>Initial Release</td>
 *	</tr>
 * </table>
 */

/**
 * \page asfdoc_sam0_system_clock_exqsg Examples for System Clock Driver
 *
 * This is a list of the available Quick Start guides (QSGs) and example
 * applications for \ref asfdoc_sam0_system_clock_group. QSGs are simple
 * examples with step-by-step instructions to configure and use this driver in
 * a selection of use cases. Note that QSGs can be compiled as a standalone
 * application or be added to the user application.
 *
 *  - \subpage asfdoc_sam0_system_clock_basic_use_case
 *  - \subpage asfdoc_sam0_system_gclk_basic_use_case
 *
 * \page asfdoc_sam0_system_clock_document_revision_history Document Revision History
 *
 * <table>
 *	<tr>
 *		<th>Doc. Rev.</td>
 *		<th>Date</td>
 *		<th>Comments</td>
 *	</tr>
 *	<tr>
 *		<td>E</td>
 *		<td>04/2015</td>
 *		<td>Added support for SAMDAx.</td>
 *	</tr>
 *	<tr>
 *		<td>D</td>
 *		<td>12/2014</td>
 *		<td>Added support for SAMR21 and SAMD10/D11.</td>
 *	</tr>
 *	<tr>
 *		<td>C</td>
 *		<td>01/2014</td>
 *		<td>Added support for SAMD21.</td>
 *	</tr>
 *	<tr>
 *		<td>B</td>
 *		<td>06/2013</td>
 *		<td>Corrected documentation typos. Fixed missing steps in the Basic
 *          Use Case Quick Start Guide.</td>
 *	</tr>
 *	<tr>
 *		<td>A</td>
 *		<td>06/2013</td>
 *		<td>Initial release</td>
 *	</tr>
 * </table>
 */

#ifdef __cplusplus
}
#endif

#endif /* SYSTEM_CLOCK_FEATURE_H_INCLUDED */