mbed official
The official Mbed 2 C/C++ SDK provides the software platform and libraries to build your applications.
Dependents: hello SerialTestv11 SerialTestv12 Sierpinski ... more
mbed 2
This is the mbed 2 library. If you'd like to learn about Mbed OS please see the mbed-os docs.
TARGET_EFM32WG_STK3800/TOOLCHAIN_ARM_STD/em_lesense.h
- Committer:
- AnnaBridge
- Date:
- 2019-02-20
- Revision:
- 172:65be27845400
- Parent:
- 171:3a7713b1edbc
File content as of revision 172:65be27845400:
/***************************************************************************//**
* @file em_lesense.h
* @brief Low Energy Sensor (LESENSE) peripheral API
* @version 5.3.3
*******************************************************************************
* # License
* <b>Copyright 2016 Silicon Laboratories, Inc. http://www.silabs.com</b>
*******************************************************************************
*
* Permission is granted to anyone to use this software for any purpose,
* including commercial applications, and to alter it and redistribute it
* freely, subject to the following restrictions:
*
* 1. The origin of this software must not be misrepresented; you must not
* claim that you wrote the original software.
* 2. Altered source versions must be plainly marked as such, and must not be
* misrepresented as being the original software.
* 3. This notice may not be removed or altered from any source distribution.
*
* DISCLAIMER OF WARRANTY/LIMITATION OF REMEDIES: Silicon Labs has no
* obligation to support this Software. Silicon Labs is providing the
* Software "AS IS", with no express or implied warranties of any kind,
* including, but not limited to, any implied warranties of merchantability
* or fitness for any particular purpose or warranties against infringement
* of any proprietary rights of a third party.
*
* Silicon Labs will not be liable for any consequential, incidental, or
* special damages, or any other relief, or for any claim by any third party,
* arising from your use of this Software.
*
******************************************************************************/
#ifndef EM_LESENSE_H
#define EM_LESENSE_H
#include "em_device.h"
#if defined(LESENSE_COUNT) && (LESENSE_COUNT > 0)
#include <stdint.h>
#include <stdbool.h>
#ifdef __cplusplus
extern "C" {
#endif
/***************************************************************************//**
* @addtogroup emlib
* @{
******************************************************************************/
/***************************************************************************//**
* @addtogroup LESENSE
* @{
******************************************************************************/
/** Number of decoder states supported by current device. */
#define LESENSE_NUM_DECODER_STATES (_LESENSE_DECSTATE_DECSTATE_MASK + 1)
/** Number of LESENSE channels. */
#define LESENSE_NUM_CHANNELS 16
/*******************************************************************************
******************************** ENUMS ************************************
******************************************************************************/
/** Clock divisors for controlling the prescaling factor of the period
* counter.
* Note: these enumeration values are being used for different clock division
* related configuration parameters (hfPresc, lfPresc, pcPresc). */
typedef enum {
lesenseClkDiv_1 = 0, /**< Divide clock by 1. */
lesenseClkDiv_2 = 1, /**< Divide clock by 2. */
lesenseClkDiv_4 = 2, /**< Divide clock by 4. */
lesenseClkDiv_8 = 3, /**< Divide clock by 8. */
lesenseClkDiv_16 = 4, /**< Divide clock by 16. */
lesenseClkDiv_32 = 5, /**< Divide clock by 32. */
lesenseClkDiv_64 = 6, /**< Divide clock by 64. */
lesenseClkDiv_128 = 7 /**< Divide clock by 128. */
} LESENSE_ClkPresc_TypeDef;
/** Scan modes. */
typedef enum {
/** New scan is started each time the period counter overflows. */
lesenseScanStartPeriodic = LESENSE_CTRL_SCANMODE_PERIODIC,
/** Single scan is performed when LESENSE_ScanStart() is called. */
lesenseScanStartOneShot = LESENSE_CTRL_SCANMODE_ONESHOT,
/** New scan is triggered by pulse on PRS channel. */
lesenseScanStartPRS = LESENSE_CTRL_SCANMODE_PRS
} LESENSE_ScanMode_TypeDef;
/** PRS sources.
* Note: these enumeration values are being used for different PRS related
* configuration parameters. */
typedef enum {
lesensePRSCh0 = 0, /**< PRS channel 0. */
lesensePRSCh1 = 1, /**< PRS channel 1. */
lesensePRSCh2 = 2, /**< PRS channel 2. */
lesensePRSCh3 = 3, /**< PRS channel 3. */
#if defined(LESENSE_CTRL_PRSSEL_PRSCH4)
lesensePRSCh4 = 4, /**< PRS channel 4. */
#endif
#if defined(LESENSE_CTRL_PRSSEL_PRSCH5)
lesensePRSCh5 = 5, /**< PRS channel 5. */
#endif
#if defined(LESENSE_CTRL_PRSSEL_PRSCH6)
lesensePRSCh6 = 6, /**< PRS channel 6. */
#endif
#if defined(LESENSE_CTRL_PRSSEL_PRSCH7)
lesensePRSCh7 = 7, /**< PRS channel 7. */
#endif
#if defined(LESENSE_CTRL_PRSSEL_PRSCH8)
lesensePRSCh8 = 8, /**< PRS channel 8. */
#endif
#if defined(LESENSE_CTRL_PRSSEL_PRSCH9)
lesensePRSCh9 = 9, /**< PRS channel 9. */
#endif
#if defined(LESENSE_CTRL_PRSSEL_PRSCH10)
lesensePRSCh10 = 10, /**< PRS channel 10.*/
#endif
#if defined(LESENSE_CTRL_PRSSEL_PRSCH11)
lesensePRSCh11 = 11, /**< PRS channel 11.*/
#endif
} LESENSE_PRSSel_TypeDef;
/** Locations of the alternate excitation function. */
typedef enum {
/** Alternate excitation is mapped to the LES_ALTEX pins. */
lesenseAltExMapALTEX = _LESENSE_CTRL_ALTEXMAP_ALTEX,
#if defined(_LESENSE_CTRL_ALTEXMAP_ACMP)
/** Alternate excitation is mapped to the pins of the other ACMP. */
lesenseAltExMapACMP = _LESENSE_CTRL_ALTEXMAP_ACMP,
#endif
#if defined(_LESENSE_CTRL_ALTEXMAP_CH)
/** Alternative excitation is mapped to the pin of LESENSE channel
* (X+8 mod 16), X being the active channel. */
lesenseAltExMapCH = _LESENSE_CTRL_ALTEXMAP_CH,
#endif
} LESENSE_AltExMap_TypeDef;
/** Result buffer interrupt and DMA trigger levels. */
typedef enum {
/** DMA and interrupt flags are set when result buffer is halffull. */
lesenseBufTrigHalf = LESENSE_CTRL_BUFIDL_HALFFULL,
/** DMA and interrupt flags set when result buffer is full. */
lesenseBufTrigFull = LESENSE_CTRL_BUFIDL_FULL
} LESENSE_BufTrigLevel_TypeDef;
/** Modes of operation for DMA wakeup from EM2. */
typedef enum {
/** No DMA wakeup from EM2. */
lesenseDMAWakeUpDisable = LESENSE_CTRL_DMAWU_DISABLE,
/** DMA wakeup from EM2 when data is valid in the result buffer. */
lesenseDMAWakeUpBufValid = LESENSE_CTRL_DMAWU_BUFDATAV,
/** DMA wakeup from EM2 when the resultbuffer is full/halffull, depending on
* RESBIDL configuration in LESENSE_CTRL register (selected by
* resBufTrigLevel in LESENSE_ResBufTrigLevel_TypeDef descriptor structure). */
lesenseDMAWakeUpBufLevel = LESENSE_CTRL_DMAWU_BUFLEVEL
} LESENSE_DMAWakeUp_TypeDef;
/** Bias modes. */
typedef enum {
/** Duty cycle bias module between low power and high accuracy mode. */
lesenseBiasModeDutyCycle = LESENSE_BIASCTRL_BIASMODE_DUTYCYCLE,
/** Bias module is always in high accuracy mode. */
lesenseBiasModeHighAcc = LESENSE_BIASCTRL_BIASMODE_HIGHACC,
/** Bias module is controlled by the EMU and not affected by LESENSE. */
lesenseBiasModeDontTouch = LESENSE_BIASCTRL_BIASMODE_DONTTOUCH
} LESENSE_BiasMode_TypeDef;
/** Scan configuration. */
typedef enum {
/** The channel configuration registers (CHx_CONF) used are directly mapped to
* the channel number. */
lesenseScanConfDirMap = LESENSE_CTRL_SCANCONF_DIRMAP,
/** The channel configuration registers used are CHx+8_CONF for channels 0-7
* and CHx-8_CONF for channels 8-15. */
lesenseScanConfInvMap = LESENSE_CTRL_SCANCONF_INVMAP,
/** The channel configuration registers used toggles between CHX_SCANCONF and
* CHX+8_SCANCONF when channel x triggers. */
lesenseScanConfToggle = LESENSE_CTRL_SCANCONF_TOGGLE,
/** The decoder state defines the channel configuration register (CHx_CONF) to
* be used. */
lesenseScanConfDecDef = LESENSE_CTRL_SCANCONF_DECDEF
} LESENSE_ScanConfSel_TypeDef;
/** DAC CHx data control configuration. */
typedef enum {
/** DAC channel x data is defined by DAC_CHxDATA register.
* Note: this value could be used for both DAC Ch0 and Ch1. */
lesenseDACIfData = _LESENSE_PERCTRL_DACCH0DATA_DACDATA,
#if defined(_LESENSE_PERCTRL_DACCH0DATA_ACMPTHRES)
/** DAC channel x data is defined by ACMPTHRES in LESENSE_CHx_INTERACT.
* Note: this value could be used for both DAC Ch0 and Ch1. */
lesenseACMPThres = _LESENSE_PERCTRL_DACCH0DATA_ACMPTHRES,
#endif
#if defined(_LESENSE_PERCTRL_DACCH0DATA_THRES)
/** DAC channel x data is defined by THRES in LESENSE_CHx_INTERACT.
* Note: this value could be used for both DAC Ch0 and Ch1. */
lesenseThres = _LESENSE_PERCTRL_DACCH0DATA_THRES,
#endif
} LESENSE_ControlDACData_TypeDef;
#if defined(_LESENSE_PERCTRL_DACCH0CONV_MASK)
/** DAC channel x conversion mode configuration. */
typedef enum {
/** LESENSE doesn't control DAC channel x.
* Note: this value could be used for both DAC Ch0 and Ch1. */
lesenseDACConvModeDisable = _LESENSE_PERCTRL_DACCH0CONV_DISABLE,
/** DAC channel x is driven in continuous mode.
* Note: this value could be used for both DAC Ch0 and Ch1. */
lesenseDACConvModeContinuous = _LESENSE_PERCTRL_DACCH0CONV_CONTINUOUS,
/** DAC channel x is driven in sample hold mode.
* Note: this value could be used for both DAC Ch0 and Ch1. */
lesenseDACConvModeSampleHold = _LESENSE_PERCTRL_DACCH0CONV_SAMPLEHOLD,
/** DAC channel x is driven in sample off mode.
* Note: this value could be used for both DAC Ch0 and Ch1. */
lesenseDACConvModeSampleOff = _LESENSE_PERCTRL_DACCH0CONV_SAMPLEOFF
} LESENSE_ControlDACConv_TypeDef;
#endif
#if defined(_LESENSE_PERCTRL_DACCH0OUT_MASK)
/** DAC channel x output mode configuration. */
typedef enum {
/** DAC CHx output to pin and ACMP/ADC disabled.
* Note: this value could be used for both DAC Ch0 and Ch1. */
lesenseDACOutModeDisable = _LESENSE_PERCTRL_DACCH0OUT_DISABLE,
/** DAC CHx output to pin enabled, output to ADC and ACMP disabled.
* Note: this value could be used for both DAC Ch0 and Ch1. */
lesenseDACOutModePin = _LESENSE_PERCTRL_DACCH0OUT_PIN,
/** DAC CHx output to pin disabled, output to ADC and ACMP enabled.
* Note: this value could be used for both DAC Ch0 and Ch1. */
lesenseDACOutModeADCACMP = _LESENSE_PERCTRL_DACCH0OUT_ADCACMP,
/** DAC CHx output to pin, ADC, and ACMP enabled.
* Note: this value could be used for both DAC Ch0 and Ch1. */
lesenseDACOutModePinADCACMP = _LESENSE_PERCTRL_DACCH0OUT_PINADCACMP
} LESENSE_ControlDACOut_TypeDef;
#endif
#if defined(_LESENSE_PERCTRL_DACREF_MASK)
/** DAC reference configuration. */
typedef enum {
/** DAC uses VDD reference. */
lesenseDACRefVdd = LESENSE_PERCTRL_DACREF_VDD,
/** DAC uses bandgap reference. */
lesenseDACRefBandGap = LESENSE_PERCTRL_DACREF_BANDGAP
} LESENSE_DACRef_TypeDef;
#endif
/** ACMPx control configuration. */
typedef enum {
/** LESENSE does not control the ACMPx.
* Note: this value could be used for both ACMP0 and ACMP1. */
lesenseACMPModeDisable = _LESENSE_PERCTRL_ACMP0MODE_DISABLE,
/** LESENSE controls the input mux of ACMPx.
* Note: this value could be used for both ACMP0 and ACMP1. */
lesenseACMPModeMux = _LESENSE_PERCTRL_ACMP0MODE_MUX,
/** LESENSE controls the input mux of and the threshold value of ACMPx.
* Note: this value could be used for both ACMP0 and ACMP1. */
lesenseACMPModeMuxThres = _LESENSE_PERCTRL_ACMP0MODE_MUXTHRES
} LESENSE_ControlACMP_TypeDef;
/** Warm up modes. ACMP and DAC duty cycle mode configuration. */
typedef enum {
/** ACMPs and DACs are shut down when LESENSE is idle. */
lesenseWarmupModeNormal = LESENSE_PERCTRL_WARMUPMODE_NORMAL,
/** ACMPs are kept powered up when LESENSE is idle. */
lesenseWarmupModeACMP = LESENSE_PERCTRL_WARMUPMODE_KEEPACMPWARM,
/** The DAC is kept powered up when LESENSE is idle. */
lesenseWarmupModeDAC = LESENSE_PERCTRL_WARMUPMODE_KEEPDACWARM,
/** ACMPs and the DAC are kept powered up when LESENSE is idle. */
lesenseWarmupModeKeepWarm = LESENSE_PERCTRL_WARMUPMODE_KEEPACMPDACWARM
} LESENSE_WarmupMode_TypeDef;
/** Decoder input source configuration. */
typedef enum {
/** The SENSORSTATE register is used as input to the decoder. */
lesenseDecInputSensorSt = LESENSE_DECCTRL_INPUT_SENSORSTATE,
/** PRS channels are used as input to the decoder. */
lesenseDecInputPRS = LESENSE_DECCTRL_INPUT_PRS
} LESENSE_DecInput_TypeDef;
/** Compare source selection for sensor sampling. */
typedef enum {
/** Counter output will be used in comparison. */
lesenseSampleModeCounter = 0x0 << _LESENSE_CH_INTERACT_SAMPLE_SHIFT,
/** ACMP output will be used in comparison. */
lesenseSampleModeACMP = LESENSE_CH_INTERACT_SAMPLE_ACMP,
#if defined(LESENSE_CH_INTERACT_SAMPLE_ADC)
/** ADC output will be used in comparison. */
lesenseSampleModeADC = LESENSE_CH_INTERACT_SAMPLE_ADC,
/** Differential ADC output will be used in comparison. */
lesenseSampleModeADCDiff = LESENSE_CH_INTERACT_SAMPLE_ADCDIFF,
#endif
} LESENSE_ChSampleMode_TypeDef;
/** Interrupt generation setup for CHx interrupt flag. */
typedef enum {
/** No interrupt is generated. */
lesenseSetIntNone = LESENSE_CH_INTERACT_SETIF_NONE,
/** Set interrupt flag if the sensor triggers. */
lesenseSetIntLevel = LESENSE_CH_INTERACT_SETIF_LEVEL,
/** Set interrupt flag on positive edge of the sensor state. */
lesenseSetIntPosEdge = LESENSE_CH_INTERACT_SETIF_POSEDGE,
/** Set interrupt flag on negative edge of the sensor state. */
lesenseSetIntNegEdge = LESENSE_CH_INTERACT_SETIF_NEGEDGE
} LESENSE_ChIntMode_TypeDef;
/** Channel pin mode for the excitation phase of the scan sequence. */
typedef enum {
/** Channel pin is disabled. */
lesenseChPinExDis = LESENSE_CH_INTERACT_EXMODE_DISABLE,
/** Channel pin is configured as push-pull, driven HIGH. */
lesenseChPinExHigh = LESENSE_CH_INTERACT_EXMODE_HIGH,
/** Channel pin is configured as push-pull, driven LOW. */
lesenseChPinExLow = LESENSE_CH_INTERACT_EXMODE_LOW,
/** DAC output (only available on channel 0, 1, 2, 3, 12, 13, 14 and 15) */
lesenseChPinExDACOut = LESENSE_CH_INTERACT_EXMODE_DACOUT
} LESENSE_ChPinExMode_TypeDef;
/** Channel pin mode for the idle phase of the scan sequence. */
typedef enum {
/** Channel pin is disabled in idle phase.
* Note: this value could be used for all channels. */
lesenseChPinIdleDis = _LESENSE_IDLECONF_CH0_DISABLE,
/** Channel pin is configured as push-pull, driven HIGH in idle phase.
* Note: this value could be used for all channels. */
lesenseChPinIdleHigh = _LESENSE_IDLECONF_CH0_HIGH,
/** Channel pin is configured as push-pull, driven LOW in idle phase.
* Note: this value could be used for all channels. */
lesenseChPinIdleLow = _LESENSE_IDLECONF_CH0_LOW,
#if defined(_LESENSE_IDLECONF_CH0_DAC)
/** Channel pin is connected to DAC output in idle phase.
* Note: this value could be used for all channels. */
lesenseChPinIdleDACC = _LESENSE_IDLECONF_CH0_DAC
#else
/** Channel pin is connected to DAC CH0 output in idle phase.
* Note: only applies to channel 0, 1, 2, 3. */
lesenseChPinIdleDACCh0 = _LESENSE_IDLECONF_CH0_DACCH0,
/** Channel pin is connected to DAC CH1 output in idle phase.
* Note: only applies to channel 12, 13, 14, 15. */
lesenseChPinIdleDACCh1 = _LESENSE_IDLECONF_CH12_DACCH1,
#endif
} LESENSE_ChPinIdleMode_TypeDef;
/** Clock used for excitation and sample delay timing. */
typedef enum {
/** LFACLK (LF clock) is used. */
lesenseClkLF = _LESENSE_CH_INTERACT_EXCLK_LFACLK,
/** AUXHFRCO (HF clock) is used. */
lesenseClkHF = _LESENSE_CH_INTERACT_EXCLK_AUXHFRCO
} LESENSE_ChClk_TypeDef;
/** Compare modes for counter comparison. */
typedef enum {
/** Comparison evaluates to 1 if the sensor data is less than the counter
* threshold, or if the ACMP output is 0. */
lesenseCompModeLess = LESENSE_CH_EVAL_COMP_LESS,
/** Comparison evaluates to 1 if the sensor data is greater than, or equal to
* the counter threshold, or if the ACMP output is 1. */
lesenseCompModeGreaterOrEq = LESENSE_CH_EVAL_COMP_GE
} LESENSE_ChCompMode_TypeDef;
#if defined(_LESENSE_CH_EVAL_MODE_MASK)
/** Sensor evaluation modes. */
typedef enum {
/** Threshold comparison evaluation mode. In this mode the sensor data
* is compared to the configured threshold value. Two possible comparison
* operators can be used on the sensor data, either >= (GE) or < (LT).
* Which operator to use is given using the
* @ref LESENSE_ChDesc_TypeDef::compMode member. */
lesenseEvalModeThreshold = _LESENSE_CH_EVAL_MODE_THRES,
/** Sliding window evaluation mode. In this mode the sensor data is
* evaluated against the upper and lower limits of a window range. The
* windows range is defined by a base value and a window size. */
lesenseEvalModeSlidingWindow = _LESENSE_CH_EVAL_MODE_SLIDINGWIN,
/** Step detection evaluation mode. In this mode the sensor data is compared
* to the sensor data from the previous measurement. The sensor evaluation
* will result in a "1" if the difference between the current measurement
* and the previous one is greater than a configurable "step size". If the
* difference is less than the configured step size then the sensor
* evaluation will result in a "0". */
lesenseEvalModeStepDetection = _LESENSE_CH_EVAL_MODE_STEPDET,
} LESENSE_ChEvalMode_TypeDef;
#endif
/** Idle phase configuration of alternate excitation channels. */
typedef enum {
/** ALTEX output is disabled in idle phase.
* Note: this value could be used for all alternate excitation channels. */
lesenseAltExPinIdleDis = _LESENSE_ALTEXCONF_IDLECONF0_DISABLE,
/** ALTEX output is high in idle phase.
* Note: this value could be used for all alternate excitation channels. */
lesenseAltExPinIdleHigh = _LESENSE_ALTEXCONF_IDLECONF0_HIGH,
/** ALTEX output is low in idle phase.
* Note: this value could be used for all alternate excitation channels. */
lesenseAltExPinIdleLow = _LESENSE_ALTEXCONF_IDLECONF0_LOW
} LESENSE_AltExPinIdle_TypeDef;
/** Transition action modes. */
typedef enum {
/** No PRS pulses generated (if PRSCOUNT == 0).
* Do not count (if PRSCOUNT == 1). */
lesenseTransActNone = LESENSE_ST_TCONFA_PRSACT_NONE,
/** Generate pulse on LESPRS0 (if PRSCOUNT == 0). */
lesenseTransActPRS0 = LESENSE_ST_TCONFA_PRSACT_PRS0,
/** Generate pulse on LESPRS1 (if PRSCOUNT == 0). */
lesenseTransActPRS1 = LESENSE_ST_TCONFA_PRSACT_PRS1,
/** Generate pulse on LESPRS0 and LESPRS1 (if PRSCOUNT == 0). */
lesenseTransActPRS01 = LESENSE_ST_TCONFA_PRSACT_PRS01,
/** Generate pulse on LESPRS2 (for both PRSCOUNT == 0 and PRSCOUNT == 1). */
lesenseTransActPRS2 = LESENSE_ST_TCONFA_PRSACT_PRS2,
/** Generate pulse on LESPRS0 and LESPRS2 (if PRSCOUNT == 0). */
lesenseTransActPRS02 = LESENSE_ST_TCONFA_PRSACT_PRS02,
/** Generate pulse on LESPRS1 and LESPRS2 (if PRSCOUNT == 0). */
lesenseTransActPRS12 = LESENSE_ST_TCONFA_PRSACT_PRS12,
/** Generate pulse on LESPRS0, LESPRS1 and LESPRS2 (if PRSCOUNT == 0). */
lesenseTransActPRS012 = LESENSE_ST_TCONFA_PRSACT_PRS012,
/** Count up (if PRSCOUNT == 1). */
lesenseTransActUp = LESENSE_ST_TCONFA_PRSACT_UP,
/** Count down (if PRSCOUNT == 1). */
lesenseTransActDown = LESENSE_ST_TCONFA_PRSACT_DOWN,
/** Count up and generate pulse on LESPRS2 (if PRSCOUNT == 1). */
lesenseTransActUpAndPRS2 = LESENSE_ST_TCONFA_PRSACT_UPANDPRS2,
/** Count down and generate pulse on LESPRS2 (if PRSCOUNT == 1). */
lesenseTransActDownAndPRS2 = LESENSE_ST_TCONFA_PRSACT_DOWNANDPRS2
} LESENSE_StTransAct_TypeDef;
/*******************************************************************************
******************************* STRUCTS ***********************************
******************************************************************************/
/** Core control (LESENSE_CTRL) descriptor structure. */
typedef struct {
/** Select scan start mode to control how the scan start is being triggered.*/
LESENSE_ScanMode_TypeDef scanStart;
/** Select PRS source for scan start if scanMode is set to lesensePrsPulse. */
LESENSE_PRSSel_TypeDef prsSel;
/** Select scan configuration register usage strategy. */
LESENSE_ScanConfSel_TypeDef scanConfSel;
/** Set to true to invert ACMP0 output. */
bool invACMP0;
/** Set to true to invert ACMP1 output. */
bool invACMP1;
/** Set to true to sample both ACMPs simultaneously. */
bool dualSample;
/** Set to true in order to to store SCANRES in RAM (accessible via RESDATA)
* after each scan. */
bool storeScanRes;
/** Set to true in order to always make LESENSE write to the result buffer,
* even if it is full. */
bool bufOverWr;
/** Select trigger conditions for interrupt and DMA. */
LESENSE_BufTrigLevel_TypeDef bufTrigLevel;
/** Configure trigger condition for DMA wakeup from EM2. */
LESENSE_DMAWakeUp_TypeDef wakeupOnDMA;
/** Select bias mode. */
LESENSE_BiasMode_TypeDef biasMode;
/** Set to true to keep LESENSE running in debug mode. */
bool debugRun;
} LESENSE_CoreCtrlDesc_TypeDef;
/** Default configuration for LESENSE_CtrlDesc_TypeDef structure. */
#define LESENSE_CORECTRL_DESC_DEFAULT \
{ \
lesenseScanStartPeriodic,/* Start new scan each time the period counter overflows. */ \
lesensePRSCh0, /* Default PRS channel is selected. */ \
lesenseScanConfDirMap, /* Direct mapping SCANCONF register usage strategy. */ \
false, /* Don't invert ACMP0 output. */ \
false, /* Don't invert ACMP1 output. */ \
false, /* Disable dual sampling. */ \
true, /* Store scan result after each scan. */ \
true, /* Overwrite result buffer register even if it is full. */ \
lesenseBufTrigHalf, /* Trigger interrupt and DMA request if result buffer is half full. */ \
lesenseDMAWakeUpDisable, /* Don't wake up on DMA from EM2. */ \
lesenseBiasModeDontTouch,/* Don't touch bias configuration. */ \
true /* Keep LESENSE running in debug mode. */ \
}
/** LESENSE timing control descriptor structure. */
typedef struct {
/** Set the number of LFACLK cycles to delay sensor interaction on
* each channel. Valid range: 0-3 (2 bit). */
uint8_t startDelay;
/**
* Set to true do delay the startup of AUXHFRCO until the system enters
* the excite phase. This will reduce the time AUXHFRCO is enabled and
* reduce power usage. */
bool delayAuxStartup;
} LESENSE_TimeCtrlDesc_TypeDef;
/** Default configuration for LESENSE_TimeCtrlDesc_TypeDef structure. */
#define LESENSE_TIMECTRL_DESC_DEFAULT \
{ \
0U, /* No sensor interaction delay. */ \
false /* Don't delay the AUXHFRCO startup. */ \
}
/** LESENSE peripheral control descriptor structure. */
typedef struct {
/** Configure DAC channel 0 data control. */
LESENSE_ControlDACData_TypeDef dacCh0Data;
#if defined(_LESENSE_PERCTRL_DACCH0CONV_MASK)
/** Configure how LESENSE controls conversion on DAC channel 0. */
LESENSE_ControlDACConv_TypeDef dacCh0ConvMode;
#endif
#if defined(_LESENSE_PERCTRL_DACCH0OUT_MASK)
/** Configure how LESENSE controls output on DAC channel 0. */
LESENSE_ControlDACOut_TypeDef dacCh0OutMode;
#endif
/** Configure DAC channel 1 data control. */
LESENSE_ControlDACData_TypeDef dacCh1Data;
#if defined(_LESENSE_PERCTRL_DACCH1CONV_MASK)
/** Configure how LESENSE controls conversion on DAC channel 1. */
LESENSE_ControlDACConv_TypeDef dacCh1ConvMode;
#endif
#if defined(_LESENSE_PERCTRL_DACCH1OUT_MASK)
/** Configure how LESENSE controls output on DAC channel 1. */
LESENSE_ControlDACOut_TypeDef dacCh1OutMode;
#endif
#if defined(_LESENSE_PERCTRL_DACPRESC_MASK)
/** Configure the prescaling factor for the LESENSE - DAC interface.
* Valid range: 0-31 (5bit). */
uint8_t dacPresc;
#endif
#if defined(_LESENSE_PERCTRL_DACREF_MASK)
/** Configure the DAC reference to be used. Set to #lesenseDACRefVdd to use
* VDD and set to #lesenseDACRefBandGap to use bandgap as reference. */
LESENSE_DACRef_TypeDef dacRef;
#endif
/** Configure how LESENSE controls ACMP 0. */
LESENSE_ControlACMP_TypeDef acmp0Mode;
/** Configure how LESENSE controls ACMP 1. */
LESENSE_ControlACMP_TypeDef acmp1Mode;
/** Configure how LESENSE controls ACMPs and the DAC in idle mode. */
LESENSE_WarmupMode_TypeDef warmupMode;
#if defined(_LESENSE_PERCTRL_DACCONVTRIG_MASK)
/** When set to true the DAC is only enabled once for each scan. When
* set to false the DAC is enabled before every channel measurement. */
bool dacScan;
#endif
#if defined(_LESENSE_PERCTRL_DACSTARTUP_MASK)
/** When set to true the DAC is started a half clock cycle before sensor
* interaction starts. When set to false, a full clock cycle is used. */
bool dacStartupHalf;
#endif
#if defined(_LESENSE_PERCTRL_DACCH0EN_MASK)
/** When set to true, LESENSE controls DAC channel 0. */
bool dacCh0En;
#endif
#if defined(_LESENSE_PERCTRL_DACCH1EN_MASK)
/** When set to true, LESENSE controls DAC channel 1. */
bool dacCh1En;
#endif
} LESENSE_PerCtrlDesc_TypeDef;
/** Default configuration for LESENSE_PerCtrl_TypeDef structure. */
#if defined(_SILICON_LABS_32B_SERIES_0)
#define LESENSE_PERCTRL_DESC_DEFAULT \
{ \
lesenseDACIfData, /* DAC channel 0 data is defined by DAC_CH0DATA register */ \
lesenseDACConvModeDisable,/* LESENSE does not control DAC CH0. */ \
lesenseDACOutModeDisable, /* DAC channel 0 output to pin disabled. */ \
lesenseDACIfData, /* DAC channel 1 data is defined by DAC_CH1DATA register */ \
lesenseDACConvModeDisable,/* LESENSE does not control DAC CH1. */ \
lesenseDACOutModeDisable, /* DAC channel 1 output to pin disabled. */ \
0U, /* DAC prescaling factor of 1 (0+1). */ \
lesenseDACRefVdd, /* DAC uses VDD reference. */ \
lesenseACMPModeMuxThres, /* LESENSE controls the input mux and the threshold value of ACMP0. */ \
lesenseACMPModeMuxThres, /* LESENSE controls the input mux and the threshold value of ACMP1. */ \
lesenseWarmupModeKeepWarm /* Keep both ACMPs and the DAC powered up when LESENSE is idle. */ \
}
#else
#define LESENSE_PERCTRL_DESC_DEFAULT \
{ \
lesenseDACIfData, /* DAC channel 0 data is defined by DAC_CH0DATA register. */ \
lesenseDACIfData, /* DAC channel 1 data is defined by DAC_CH1DATA register. */ \
lesenseACMPModeMuxThres, /* LESENSE controls the input mux and the threshold value of ACMP0. */ \
lesenseACMPModeMuxThres, /* LESENSE controls the input mux and the threshold value of ACMP1. */ \
lesenseWarmupModeKeepWarm,/* Keep both ACMPs and the DAC powered up when LESENSE is idle. */ \
false, /* DAC is enabled for before every channel measurement. */ \
false, /* DAC is enabled a full clock cycle before sensor interaction */ \
false, /* LESENSE does not control DAC channel 0. */ \
false /* LESENSE does not control DAC channel 1. */ \
}
#endif
/** LESENSE decoder control descriptor structure. */
typedef struct {
/** Select the input to the LESENSE decoder. */
LESENSE_DecInput_TypeDef decInput;
/** Initial state of the LESENSE decoder. */
uint32_t initState;
/** Set to enable the decoder to check the present state in addition
* to the states defined in TCONF. */
bool chkState;
/** When set, a transition from state x in the decoder will set interrupt flag
* CHx. */
bool intMap;
/** Set to enable hysteresis in the decoder for suppressing changes on PRS
* channel 0. */
bool hystPRS0;
/** Set to enable hysteresis in the decoder for suppressing changes on PRS
* channel 1. */
bool hystPRS1;
/** Set to enable hysteresis in the decoder for suppressing changes on PRS
* channel 2. */
bool hystPRS2;
/** Set to enable hysteresis in the decoder for suppressing interrupt
* requests. */
bool hystIRQ;
/** Set to enable count mode on decoder PRS channels 0 and 1 to produce
* outputs which can be used by a PCNT to count up or down. */
bool prsCount;
/** Select PRS channel input for bit 0 of the LESENSE decoder. */
LESENSE_PRSSel_TypeDef prsChSel0;
/** Select PRS channel input for bit 1 of the LESENSE decoder. */
LESENSE_PRSSel_TypeDef prsChSel1;
/** Select PRS channel input for bit 2 of the LESENSE decoder. */
LESENSE_PRSSel_TypeDef prsChSel2;
/** Select PRS channel input for bit 3 of the LESENSE decoder. */
LESENSE_PRSSel_TypeDef prsChSel3;
} LESENSE_DecCtrlDesc_TypeDef;
/** Default configuration for LESENSE_PerCtrl_TypeDef structure. */
#define LESENSE_DECCTRL_DESC_DEFAULT \
{ \
lesenseDecInputSensorSt, /* The SENSORSTATE register is used as input to the decoder. */ \
0U, /* State 0 is the initial state of the decoder. */ \
false, /* Disable check of current state. */ \
true, /* Enable channel x % 16 interrupt on state x change. */ \
true, /* Enable decoder hysteresis on PRS0 output. */ \
true, /* Enable decoder hysteresis on PRS1 output. */ \
true, /* Enable decoder hysteresis on PRS2 output. */ \
true, /* Enable decoder hysteresis on PRS3 output. */ \
false, /* Disable count mode on decoder PRS channels 0 and 1*/ \
lesensePRSCh0, /* PRS Channel 0 as input for bit 0 of the LESENSE decoder. */ \
lesensePRSCh1, /* PRS Channel 1 as input for bit 1 of the LESENSE decoder. */ \
lesensePRSCh2, /* PRS Channel 2 as input for bit 2 of the LESENSE decoder. */ \
lesensePRSCh3, /* PRS Channel 3 as input for bit 3 of the LESENSE decoder. */ \
}
/** LESENSE module initialization structure. */
typedef struct {
/** LESENSE core configuration parameters. */
LESENSE_CoreCtrlDesc_TypeDef coreCtrl;
/** LESENSE timing configuration parameters. */
LESENSE_TimeCtrlDesc_TypeDef timeCtrl;
/** LESENSE peripheral configuration parameters. */
LESENSE_PerCtrlDesc_TypeDef perCtrl;
/** LESENSE decoder configuration parameters. */
LESENSE_DecCtrlDesc_TypeDef decCtrl;
} LESENSE_Init_TypeDef;
/** Default configuration for LESENSE_Init_TypeDef structure. */
#define LESENSE_INIT_DEFAULT \
{ \
.coreCtrl = LESENSE_CORECTRL_DESC_DEFAULT, /* Default core control parameters. */ \
.timeCtrl = LESENSE_TIMECTRL_DESC_DEFAULT, /* Default time control parameters. */ \
.perCtrl = LESENSE_PERCTRL_DESC_DEFAULT, /* Default peripheral control parameters. */ \
.decCtrl = LESENSE_DECCTRL_DESC_DEFAULT /* Default decoder control parameters. */ \
}
/** Channel descriptor structure. */
typedef struct {
/** Set to enable scan channel CHx. */
bool enaScanCh;
/** Set to enable CHx pin. */
bool enaPin;
/** Enable/disable channel interrupts after configuring all the sensor channel
* parameters. */
bool enaInt;
/** Configure channel pin mode for the excitation phase of the scan sequence.
* Note: OPAOUT is only available on channels 2, 3, 4, and 5. */
LESENSE_ChPinExMode_TypeDef chPinExMode;
/** Configure channel pin idle setup in LESENSE idle phase. */
LESENSE_ChPinIdleMode_TypeDef chPinIdleMode;
/** Set to use alternate excite pin for excitation. */
bool useAltEx;
/** Set to enable the result from this channel being shifted into the decoder
* register. */
bool shiftRes;
/** Set to invert the result bit stored in SCANRES register. */
bool invRes;
/** Set to store the counter value in RAM (accessible via RESDATA) and make
* the comparison result available in the SCANRES register. */
bool storeCntRes;
/** Select clock used for excitation timing. */
LESENSE_ChClk_TypeDef exClk;
/** Select clock used for sample delay timing. */
LESENSE_ChClk_TypeDef sampleClk;
/** Configure excitation time. Excitation will last exTime+1 excitation clock
* cycles. Valid range: 0-63 (6 bits). */
uint8_t exTime;
/** Configure sample delay. Sampling will occur after sampleDelay+1 sample
* clock cycles. Valid range: 0-127 (7 bits) or 0-255 (8 bits) depending on
* device. */
uint8_t sampleDelay;
/** Configure measure delay. Sensor measuring is delayed for measDelay
* excitation clock cycles. Valid range: 0-127 (7 bits) or 0-1023 (10 bits)
* depending on device. */
uint16_t measDelay;
/** Configure ACMP threshold or DAC data.
* If perCtrl.dacCh0Data or perCtrl.dacCh1Data is set to #lesenseDACIfData,
* acmpThres defines the 12-bit DAC data in the corresponding data register
* of the DAC interface (DACn_CH0DATA and DACn_CH1DATA).
* In this case, the valid range is: 0-4095 (12 bits).
* If perCtrl.dacCh0Data or perCtrl.dacCh1Data is set to #lesenseACMPThres,
* acmpThres defines the 6-bit Vdd scaling factor of ACMP negative input
* (VDDLEVEL in ACMP_INPUTSEL register).
* In this case, the valid range is: 0-63 (6 bits). */
uint16_t acmpThres;
/** Select if ACMP output, ADC output or counter output should be used in
* comparison. */
LESENSE_ChSampleMode_TypeDef sampleMode;
/** Configure interrupt generation mode for CHx interrupt flag. */
LESENSE_ChIntMode_TypeDef intMode;
/** Configure decision threshold for sensor data comparison.
* Valid range: 0-65535 (16 bits). */
uint16_t cntThres;
/** Select mode for counter comparison. */
LESENSE_ChCompMode_TypeDef compMode;
#if defined(_LESENSE_CH_EVAL_MODE_MASK)
/** Select sensor evaluation mode. */
LESENSE_ChEvalMode_TypeDef evalMode;
#endif
} LESENSE_ChDesc_TypeDef;
/** Configuration structure for all scan channels. */
typedef struct {
/** Channel descriptor for all LESENSE channels. */
LESENSE_ChDesc_TypeDef Ch[LESENSE_NUM_CHANNELS];
} LESENSE_ChAll_TypeDef;
/** Default configuration for scan channel. */
#if defined(_LESENSE_CH_EVAL_MODE_MASK)
#define LESENSE_CH_CONF_DEFAULT \
{ \
false, /* Disable scan channel. */ \
false, /* Disable the assigned pin on scan channel. */ \
false, /* Disable interrupts on channel. */ \
lesenseChPinExDis, /* Channel pin is disabled during the excitation period. */ \
lesenseChPinIdleDis, /* Channel pin is disabled during the idle period. */ \
false, /* Don't use alternate excitation pins for excitation. */ \
false, /* Disabled to shift results from this channel to the decoder register. */ \
false, /* Disabled to invert the scan result bit. */ \
false, /* Disabled to store counter value in the result buffer. */ \
lesenseClkLF, /* Use the LF clock for excitation timing. */ \
lesenseClkLF, /* Use the LF clock for sample timing. */ \
0x00U, /* Excitation time is set to 0(+1) excitation clock cycles. */ \
0x00U, /* Sample delay is set to 0(+1) sample clock cycles. */ \
0x00U, /* Measure delay is set to 0 excitation clock cycles.*/ \
0x00U, /* ACMP threshold has been set to 0. */ \
lesenseSampleModeACMP, /* ACMP output will be used in comparison. */ \
lesenseSetIntNone, /* No interrupt is generated by the channel. */ \
0x00U, /* Counter threshold has bee set to 0x00. */ \
lesenseCompModeLess, /* Compare mode has been set to trigger interrupt on "less". */ \
lesenseEvalModeThreshold /* Eval mode has been set to trigger interrupt on threshold. */ \
}
#else
#define LESENSE_CH_CONF_DEFAULT \
{ \
false, /* Disable scan channel. */ \
false, /* Disable the assigned pin on scan channel. */ \
false, /* Disable interrupts on channel. */ \
lesenseChPinExDis, /* Channel pin is disabled during the excitation period. */ \
lesenseChPinIdleDis, /* Channel pin is disabled during the idle period. */ \
false, /* Don't use alternate excitation pins for excitation. */ \
false, /* Disabled to shift results from this channel to the decoder register. */ \
false, /* Disabled to invert the scan result bit. */ \
false, /* Disabled to store counter value in the result buffer. */ \
lesenseClkLF, /* Use the LF clock for excitation timing. */ \
lesenseClkLF, /* Use the LF clock for sample timing. */ \
0x00U, /* Excitation time is set to 0(+1) excitation clock cycles. */ \
0x00U, /* Sample delay is set to 0(+1) sample clock cycles. */ \
0x00U, /* Measure delay is set to 0 excitation clock cycles.*/ \
0x00U, /* ACMP threshold has been set to 0. */ \
lesenseSampleModeACMP, /* ACMP output will be used in comparison. */ \
lesenseSetIntNone, /* No interrupt is generated by the channel. */ \
0x00U, /* Counter threshold has bee set to 0x00. */ \
lesenseCompModeLess /* Compare mode has been set to trigger interrupt on "less". */ \
}
#endif
/** Default configuration for all sensor channels. */
#define LESENSE_SCAN_CONF_DEFAULT \
{ \
{ \
LESENSE_CH_CONF_DEFAULT, /* Scan channel 0. */ \
LESENSE_CH_CONF_DEFAULT, /* Scan channel 1. */ \
LESENSE_CH_CONF_DEFAULT, /* Scan channel 2. */ \
LESENSE_CH_CONF_DEFAULT, /* Scan channel 3. */ \
LESENSE_CH_CONF_DEFAULT, /* Scan channel 4. */ \
LESENSE_CH_CONF_DEFAULT, /* Scan channel 5. */ \
LESENSE_CH_CONF_DEFAULT, /* Scan channel 6. */ \
LESENSE_CH_CONF_DEFAULT, /* Scan channel 7. */ \
LESENSE_CH_CONF_DEFAULT, /* Scan channel 8. */ \
LESENSE_CH_CONF_DEFAULT, /* Scan channel 9. */ \
LESENSE_CH_CONF_DEFAULT, /* Scan channel 10. */ \
LESENSE_CH_CONF_DEFAULT, /* Scan channel 11. */ \
LESENSE_CH_CONF_DEFAULT, /* Scan channel 12. */ \
LESENSE_CH_CONF_DEFAULT, /* Scan channel 13. */ \
LESENSE_CH_CONF_DEFAULT, /* Scan channel 14. */ \
LESENSE_CH_CONF_DEFAULT, /* Scan channel 15. */ \
} \
}
/** Alternate excitation descriptor structure. */
typedef struct {
/** Configure alternate excitation pins. If set, the corresponding alternate
* excitation pin/signal is enabled. */
bool enablePin;
/** Configure idle phase setup of alternate excitation pins.
The idleConf parameter is not valid when altExMap==lesenseAltExMapACMP. */
LESENSE_AltExPinIdle_TypeDef idleConf;
/** Configure how to control the external alternate excitation pins. Only
* applies if altExMap has been set to lesenseAltExMapALTEX.
* If true, the excitation happens on the corresponding alternate excitation
* pin during the excitation periods of all enabled channels.
* If false, the excitation happens on the corresponding alternate excitation
* pin ONLY during the excitation period of the corresponding channel.
* The alwaysEx parameter is not valid when altExMap==lesenseAltExMapACMP. */
bool alwaysEx;
} LESENSE_AltExDesc_TypeDef;
/** Configuration structure for alternate excitation. */
typedef struct {
/** Select alternate excitation mapping. */
LESENSE_AltExMap_TypeDef altExMap;
/** Alternate excitation channel descriptors.
* When altExMap==lesenseAltExMapALTEX only the 8 first descriptors are used.
* In this mode they describe the configuration of the LES_ALTEX0-7 pins.
* When altExMap==lesenseAltExMapACMP all 16 descriptors are used. In this
* mode they describe the configuration of the 16 possible ACMP0-1 excitation
* channels. Please refer to the user manual for a complete mapping of the
* routing.
* NOTE:
* Some parameters in the descriptors are not valid when
* altExMap==lesenseAltExMapACMP. Please refer to the definition of the
* LESENSE_AltExDesc_TypeDef structure for details regarding which parameters
* are valid. */
LESENSE_AltExDesc_TypeDef AltEx[16];
} LESENSE_ConfAltEx_TypeDef;
/** Default configuration for alternate excitation channel. */
#define LESENSE_ALTEX_CH_CONF_DEFAULT \
{ \
false, /* Alternate excitation disabled.*/ \
lesenseAltExPinIdleDis,/* Alternate excitation pin is disabled in idle. */ \
false /* Excite only for corresponding channel. */ \
}
/** Default configuration for all alternate excitation channels. */
#if defined(_LESENSE_CTRL_ALTEXMAP_ACMP)
#define LESENSE_ALTEX_CONF_DEFAULT \
{ \
lesenseAltExMapACMP, \
{ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 0. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 1. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 2. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 3. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 4. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 5. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 6. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 7. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 8. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 9. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 10. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 11. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 12. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 13. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 14. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT /* Alternate excitation channel 15. */ \
} \
}
#else
#define LESENSE_ALTEX_CONF_DEFAULT \
{ \
lesenseAltExMapCH, \
{ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 0. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 1. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 2. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 3. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 4. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 5. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 6. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 7. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 8. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 9. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 10. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 11. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 12. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 13. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT, /* Alternate excitation channel 14. */ \
LESENSE_ALTEX_CH_CONF_DEFAULT /* Alternate excitation channel 15. */ \
} \
}
#endif
/** Decoder state condition descriptor structure. */
typedef struct {
/** Configure compare value. State transition is triggered when sensor state
* equals to this value. Valid range: 0-15 (4 bits). */
uint8_t compVal;
/** Configure compare mask. Set bit X to exclude sensor X from evaluation.
* Note: decoder can handle sensor inputs from up to 4 sensors, therefore
* this mask is 4 bit long. */
uint8_t compMask;
/** Configure index of state to be entered if the sensor state equals to
* compVal. Valid range: 0-15 (4 bits). */
uint8_t nextState;
/** Configure which PRS action to perform when sensor state equals to
* compVal. */
LESENSE_StTransAct_TypeDef prsAct;
/** If enabled, interrupt flag is set when sensor state equals to compVal. */
bool setInt;
} LESENSE_DecStCond_TypeDef;
/** Default configuration for decoder state condition. */
#define LESENSE_ST_CONF_DEFAULT \
{ \
0x0FU, /* Compare value set to 0x0F. */ \
0x00U, /* All decoder inputs masked. */ \
0U, /* Next state is state 0. */ \
lesenseTransActNone, /* No PRS action performed on compare match. */ \
false /* No interrupt triggered on compare match. */ \
}
/** Decoder state x configuration structure. */
typedef struct {
/** If enabled, the state descriptor pair in the next location will also be
* evaluated. */
bool chainDesc;
/** State condition descriptor A (high level descriptor of
* LESENSE_STx_DECCONFA). */
LESENSE_DecStCond_TypeDef confA;
/** State condition descriptor B (high level descriptor of
* LESENSE_STx_DECCONFB). */
LESENSE_DecStCond_TypeDef confB;
} LESENSE_DecStDesc_TypeDef;
/** Configuration structure for the decoder. */
typedef struct {
/** Descriptor of the 16 or 32 decoder states depending on the device. */
LESENSE_DecStDesc_TypeDef St[LESENSE_NUM_DECODER_STATES];
} LESENSE_DecStAll_TypeDef;
/** Default configuration for all decoder states. */
#if defined(_SILICON_LABS_32B_SERIES_0)
#define LESENSE_DECODER_CONF_DEFAULT \
{ /* chain | Descriptor A | Descriptor B */ \
{ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 0. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 1. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 2. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 3. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 4. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 5. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 6. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 7. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 8. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 9. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 10. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 11. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 12. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 13. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 14. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT } /* Decoder state 15. */ \
} \
}
#else
#define LESENSE_DECODER_CONF_DEFAULT \
{ /* chain | Descriptor A | Descriptor B */ \
{ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 0. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 1. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 2. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 3. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 4. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 5. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 6. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 7. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 8. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 9. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 10. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 11. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 12. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 13. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 14. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 15. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 16. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 17. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 18. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 19. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 20. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 21. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 22. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 23. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 24. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 25. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 26. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 27. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 28. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 29. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT }, /* Decoder state 30. */ \
{ false, LESENSE_ST_CONF_DEFAULT, LESENSE_ST_CONF_DEFAULT } /* Decoder state 31. */ \
} \
}
#endif
/*******************************************************************************
***************************** PROTOTYPES **********************************
******************************************************************************/
void LESENSE_Init(const LESENSE_Init_TypeDef * init, bool reqReset);
void LESENSE_Reset(void);
uint32_t LESENSE_ScanFreqSet(uint32_t refFreq, uint32_t scanFreq);
void LESENSE_ScanModeSet(LESENSE_ScanMode_TypeDef scanMode, bool start);
void LESENSE_StartDelaySet(uint8_t startDelay);
void LESENSE_ClkDivSet(LESENSE_ChClk_TypeDef clk,
LESENSE_ClkPresc_TypeDef clkDiv);
void LESENSE_ChannelAllConfig(const LESENSE_ChAll_TypeDef * confChAll);
void LESENSE_ChannelConfig(const LESENSE_ChDesc_TypeDef * confCh,
uint32_t chIdx);
void LESENSE_ChannelEnable(uint8_t chIdx,
bool enaScanCh,
bool enaPin);
void LESENSE_ChannelEnableMask(uint16_t chMask, uint16_t pinMask);
void LESENSE_ChannelTimingSet(uint8_t chIdx,
uint8_t exTime,
uint8_t sampleDelay,
uint16_t measDelay);
void LESENSE_ChannelThresSet(uint8_t chIdx,
uint16_t acmpThres,
uint16_t cntThres);
#if defined(_LESENSE_CH_EVAL_MODE_MASK)
void LESENSE_ChannelSlidingWindow(uint8_t chIdx,
uint32_t windowSize,
uint32_t initValue);
void LESENSE_ChannelStepDetection(uint8_t chIdx,
uint32_t stepSize,
uint32_t initValue);
void LESENSE_WindowSizeSet(uint32_t windowSize);
void LESENSE_StepSizeSet(uint32_t stepSize);
#endif
void LESENSE_AltExConfig(const LESENSE_ConfAltEx_TypeDef * confAltEx);
void LESENSE_DecoderStateAllConfig(const LESENSE_DecStAll_TypeDef * confDecStAll);
void LESENSE_DecoderStateConfig(const LESENSE_DecStDesc_TypeDef * confDecSt,
uint32_t decSt);
void LESENSE_DecoderStateSet(uint32_t decSt);
uint32_t LESENSE_DecoderStateGet(void);
#if defined(_LESENSE_PRSCTRL_MASK)
void LESENSE_DecoderPrsOut(bool enable, uint32_t decMask, uint32_t decCmp);
#endif
void LESENSE_ScanStart(void);
void LESENSE_ScanStop(void);
void LESENSE_DecoderStart(void);
void LESENSE_ResultBufferClear(void);
/***************************************************************************//**
* @brief
* Stop LESENSE decoder.
*
* @details
* This function disables the LESENSE decoder by setting the command to the
* LESENSE_DECCTRL register.
******************************************************************************/
__STATIC_INLINE void LESENSE_DecoderStop(void)
{
/* Stop the decoder */
LESENSE->DECCTRL |= LESENSE_DECCTRL_DISABLE;
}
/***************************************************************************//**
* @brief
* Get the current status of LESENSE.
*
* @return
* This function returns the value of LESENSE_STATUS register that
* contains the OR combination of the following status bits:
* @li LESENSE_STATUS_RESV - Result data valid. Set when data is available
* in the result buffer. Cleared when the buffer is empty.
* @li LESENSE_STATUS_RESFULL - Result buffer full. Set when the result
* buffer is full.
* @li LESENSE_STATUS_RUNNING - LESENSE is active.
* @li LESENSE_STATUS_SCANACTIVE - LESENSE is currently interfacing sensors.
******************************************************************************/
__STATIC_INLINE uint32_t LESENSE_StatusGet(void)
{
return LESENSE->STATUS;
}
/***************************************************************************//**
* @brief
* Wait until the status of LESENSE is equal to what requested.
*
* @details
* This function is polling the LESENSE_STATUS register and waits until the
* requested combination of flags are set.
*
* @param[in] flag
* The OR combination of the following status bits:
* @li LESENSE_STATUS_BUFDATAV - Result data valid. Set when data is available
* in the result buffer. Cleared when the buffer is empty.
* @li LESENSE_STATUS_BUFHALFFULL - Result buffer half full. Set when the
* result buffer is half full.
* @li LESENSE_STATUS_BUFFULL - Result buffer full. Set when the result
* buffer is full.
* @li LESENSE_STATUS_RUNNING - LESENSE is active.
* @li LESENSE_STATUS_SCANACTIVE - LESENSE is currently interfacing sensors.
* @li LESENSE_STATUS_DACACTIVE - The DAC interface is currently active.
******************************************************************************/
__STATIC_INLINE void LESENSE_StatusWait(uint32_t flag)
{
while (!(LESENSE->STATUS & flag))
;
}
/***************************************************************************//**
* @brief
* Get the currently active channel index.
*
* @return
* This function returns the value of LESENSE_CHINDEX register that
* contains the index of the currently active channel (0-15).
******************************************************************************/
__STATIC_INLINE uint32_t LESENSE_ChannelActiveGet(void)
{
return LESENSE->CURCH;
}
/***************************************************************************//**
* @brief
* Get the latest scan comparison result (1 bit / channel).
*
* @return
* This function returns the value of LESENSE_SCANRES register that
* contains the comparison result of the last scan on all channels.
* Bit x is set if a comparison triggered on channel x, which means that the
* LESENSE counter met the comparison criteria set in LESENSE_CHx_EVAL by
* COMPMODE and CNTTHRES.
******************************************************************************/
__STATIC_INLINE uint32_t LESENSE_ScanResultGet(void)
{
return LESENSE->SCANRES & _LESENSE_SCANRES_SCANRES_MASK;
}
/***************************************************************************//**
* @brief
* Get the oldest unread data from the result buffer.
*
* @note
* Make sure that the STORERES bit is set in LESENSE_CHx_EVAL, or
* STRSCANRES bit is set in LESENSE_CTRL, otherwise this function will return
* undefined value.
*
* @return
* This function returns the value of LESENSE_RESDATA register that
* contains the oldest unread counter result from the result buffer.
******************************************************************************/
__STATIC_INLINE uint32_t LESENSE_ScanResultDataGet(void)
{
return LESENSE->BUFDATA;
}
/***************************************************************************//**
* @brief
* Get data from the result data buffer.
*
* @note
* Make sure that the STORERES bit is set in LESENSE_CHx_EVAL, or
* STRSCANRES bit is set in LESENSE_CTRL, otherwise this function will return
* undefined value.
*
* @param[in] idx
* Result data buffer index. Valid range: 0-15.
*
* @return
* This function returns the selected word from the result data buffer.
******************************************************************************/
__STATIC_INLINE uint32_t LESENSE_ScanResultDataBufferGet(uint32_t idx)
{
/* Note: masking is needed to avoid over-indexing! */
return LESENSE->BUF[idx & 0x0FU].DATA;
}
/***************************************************************************//**
* @brief
* Get the current state of the LESENSE sensor.
*
* @return
* This function returns the value of LESENSE_SENSORSTATE register that
* represents the current state of the LESENSE sensor.
******************************************************************************/
__STATIC_INLINE uint32_t LESENSE_SensorStateGet(void)
{
return LESENSE->SENSORSTATE;
}
#if defined(LESENSE_POWERDOWN_RAM)
/***************************************************************************//**
* @brief
* Shut off power to the LESENSE RAM, disables LESENSE.
*
* @details
* This function shuts off the LESENSE RAM in order to decrease the leakage
* current of the mcu if LESENSE is not used in your application.
*
* @note
* Warning! Once the LESENSE RAM is powered down, it cannot be powered up
* again.
******************************************************************************/
__STATIC_INLINE void LESENSE_RAMPowerDown(void)
{
/* Power down LESENSE RAM */
LESENSE->POWERDOWN = LESENSE_POWERDOWN_RAM;
}
#endif
/***************************************************************************//**
* @brief
* Clear one or more pending LESENSE interrupts.
*
* @param[in] flags
* Pending LESENSE interrupt sources to clear. Use a set of interrupt flags
* OR-ed together to clear multiple interrupt sources of the LESENSE module
* (LESENSE_IF_nnn).
******************************************************************************/
__STATIC_INLINE void LESENSE_IntClear(uint32_t flags)
{
LESENSE->IFC = flags;
}
/***************************************************************************//**
* @brief
* Enable one or more LESENSE interrupts.
*
* @param[in] flags
* LESENSE interrupt sources to enable. Use a set of interrupt flags OR-ed
* together to enable multiple interrupt sources of the LESENSE module
* (LESENSE_IF_nnn).
******************************************************************************/
__STATIC_INLINE void LESENSE_IntEnable(uint32_t flags)
{
LESENSE->IEN |= flags;
}
/***************************************************************************//**
* @brief
* Disable one or more LESENSE interrupts.
*
* @param[in] flags
* LESENSE interrupt sources to disable. Use a set of interrupt flags OR-ed
* together to disable multiple interrupt sources of the LESENSE module
* (LESENSE_IF_nnn).
******************************************************************************/
__STATIC_INLINE void LESENSE_IntDisable(uint32_t flags)
{
LESENSE->IEN &= ~flags;
}
/***************************************************************************//**
* @brief
* Set one or more pending LESENSE interrupts from SW.
*
* @param[in] flags
* LESENSE interrupt sources to set to pending. Use a set of interrupt
* flags OR-ed together to set multiple interrupt sources of the LESENSE
* module (LESENSE_IFS_nnn).
******************************************************************************/
__STATIC_INLINE void LESENSE_IntSet(uint32_t flags)
{
LESENSE->IFS = flags;
}
/***************************************************************************//**
* @brief
* Get pending LESENSE interrupt flags.
*
* @note
* The event bits are not cleared by the use of this function.
*
* @return
* Pending LESENSE interrupt sources. The OR combination of valid interrupt
* flags of the LESENSE module (LESENSE_IF_nnn).
******************************************************************************/
__STATIC_INLINE uint32_t LESENSE_IntGet(void)
{
return LESENSE->IF;
}
/***************************************************************************//**
* @brief
* Get enabled and pending LESENSE interrupt flags.
*
* @details
* Useful for handling more interrupt sources in the same interrupt handler.
*
* @note
* The event bits are not cleared by the use of this function.
*
* @return
* Pending and enabled LESENSE interrupt sources.
* The return value is the bitwise AND combination of
* - the OR combination of enabled interrupt sources in LESENSE_IEN_nnn
* register (LESENSE_IEN_nnn) and
* - the OR combination of valid interrupt flags of the LESENSE module
* (LESENSE_IF_nnn).
******************************************************************************/
__STATIC_INLINE uint32_t LESENSE_IntGetEnabled(void)
{
uint32_t tmp;
/* Store LESENSE->IEN in temporary variable in order to define explicit order
* of volatile accesses. */
tmp = LESENSE->IEN;
/* Bitwise AND of pending and enabled interrupts */
return LESENSE->IF & tmp;
}
/** @} (end addtogroup LESENSE) */
/** @} (end addtogroup emlib) */
#ifdef __cplusplus
}
#endif
#endif /* defined(LESENSE_COUNT) && (LESENSE_COUNT > 0) */
#endif /* EM_LESENSE_H */
