mbed official
mbed library sources. Supersedes mbed-src.
Dependents: Nucleo_Hello_Encoder BLE_iBeaconScan AM1805_DEMO DISCO-F429ZI_ExportTemplate1 ... more
targets/TARGET_STM/TARGET_STM32L4/device/stm32l4xx_ll_usb.c
- Committer:
- AnnaBridge
- Date:
- 2019-02-20
- Revision:
- 189:f392fc9709a3
- Parent:
- 181:57724642e740
File content as of revision 189:f392fc9709a3:
/**
******************************************************************************
* @file stm32l4xx_ll_usb.c
* @author MCD Application Team
* @brief USB Low Layer HAL module driver.
*
* This file provides firmware functions to manage the following
* functionalities of the USB Peripheral Controller:
* + Initialization/de-initialization functions
* + I/O operation functions
* + Peripheral Control functions
* + Peripheral State functions
*
@verbatim
==============================================================================
##### How to use this driver #####
==============================================================================
[..]
(#) Fill parameters of Init structure in USB_OTG_CfgTypeDef structure.
(#) Call USB_CoreInit() API to initialize the USB Core peripheral.
(#) The upper HAL HCD/PCD driver will call the right routines for its internal processes.
@endverbatim
******************************************************************************
* @attention
*
* <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2>
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
* 1. Redistributions of source code must retain the above copyright notice,
* this list of conditions and the following disclaimer.
* 2. Redistributions in binary form must reproduce the above copyright notice,
* this list of conditions and the following disclaimer in the documentation
* and/or other materials provided with the distribution.
* 3. Neither the name of STMicroelectronics nor the names of its contributors
* may be used to endorse or promote products derived from this software
* without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
* AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
* IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
* FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
* SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
* CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
* OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
* OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32l4xx_hal.h"
/** @defgroup USB_LL USB Low Layer
* @brief Low layer module for USB_FS and USB_OTG_FS drivers
* @{
*/
#if defined (HAL_PCD_MODULE_ENABLED) || defined (HAL_HCD_MODULE_ENABLED)
#if defined(STM32L432xx) || defined(STM32L433xx) || defined(STM32L442xx) || defined(STM32L443xx) || \
defined(STM32L452xx) || defined(STM32L462xx) || \
defined(STM32L475xx) || defined(STM32L476xx) || defined(STM32L485xx) || defined(STM32L486xx) || \
defined(STM32L496xx) || defined(STM32L4A6xx) || \
defined(STM32L4R5xx) || defined(STM32L4R7xx) || defined(STM32L4R9xx) || defined(STM32L4S5xx) || defined(STM32L4S7xx) || defined(STM32L4S9xx)
/** @addtogroup STM32L4xx_LL_USB_DRIVER
* @{
*/
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/
#if defined (USB_OTG_FS)
/** @defgroup USB_LL_Private_Functions USB Low Layer Private Functions
* @{
*/
static HAL_StatusTypeDef USB_CoreReset(USB_OTG_GlobalTypeDef *USBx);
/**
* @}
*/
#endif /* USB_OTG_FS */
/* Exported functions --------------------------------------------------------*/
/** @defgroup LL_USB_Exported_Functions USB Low Layer Exported Functions
* @{
*/
/** @defgroup LL_USB_Group1 Initialization/de-initialization functions
* @brief Initialization and Configuration functions
*
@verbatim
===============================================================================
##### Initialization/de-initialization functions #####
===============================================================================
[..] This section provides functions allowing to:
@endverbatim
* @{
*/
/*==============================================================================
USB OTG FS peripheral available on STM32L475xx, STM32L476xx, STM32L485xx and
STM32L486xx devices
==============================================================================*/
#if defined (USB_OTG_FS)
/**
* @brief Initializes the USB Core
* @param USBx: USB Instance
* @param cfg: pointer to a USB_OTG_CfgTypeDef structure that contains
* the configuration information for the specified USBx peripheral.
* @retval HAL status
*/
HAL_StatusTypeDef USB_CoreInit(USB_OTG_GlobalTypeDef *USBx, USB_OTG_CfgTypeDef cfg)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(cfg);
/* Select FS Embedded PHY */
USBx->GUSBCFG |= USB_OTG_GUSBCFG_PHYSEL;
/* Reset after a PHY select and set Host mode */
USB_CoreReset(USBx);
/* Deactivate the power down*/
USBx->GCCFG = USB_OTG_GCCFG_PWRDWN;
return HAL_OK;
}
/**
* @brief USB_EnableGlobalInt
* Enables the controller's Global Int in the AHB Config reg
* @param USBx: Selected device
* @retval HAL status
*/
HAL_StatusTypeDef USB_EnableGlobalInt(USB_OTG_GlobalTypeDef *USBx)
{
USBx->GAHBCFG |= USB_OTG_GAHBCFG_GINT;
return HAL_OK;
}
/**
* @brief USB_DisableGlobalInt
* Disable the controller's Global Int in the AHB Config reg
* @param USBx: Selected device
* @retval HAL status
*/
HAL_StatusTypeDef USB_DisableGlobalInt(USB_OTG_GlobalTypeDef *USBx)
{
USBx->GAHBCFG &= ~USB_OTG_GAHBCFG_GINT;
return HAL_OK;
}
/**
* @brief USB_SetCurrentMode : Set functional mode
* @param USBx: Selected device
* @param mode: current core mode
* This parameter can be one of these values:
* @arg USB_OTG_DEVICE_MODE: Peripheral mode
* @arg USB_OTG_HOST_MODE: Host mode
* @arg USB_OTG_DRD_MODE: Dual Role Device mode
* @retval HAL status
*/
HAL_StatusTypeDef USB_SetCurrentMode(USB_OTG_GlobalTypeDef *USBx , USB_ModeTypeDef mode)
{
USBx->GUSBCFG &= ~(USB_OTG_GUSBCFG_FHMOD | USB_OTG_GUSBCFG_FDMOD);
if ( mode == USB_HOST_MODE)
{
USBx->GUSBCFG |= USB_OTG_GUSBCFG_FHMOD;
}
else if ( mode == USB_DEVICE_MODE)
{
USBx->GUSBCFG |= USB_OTG_GUSBCFG_FDMOD;
}
HAL_Delay(50);
return HAL_OK;
}
/**
* @brief USB_DevInit : Initializes the USB_OTG controller registers
* for device mode
* @param USBx: Selected device
* @param cfg: pointer to a USB_OTG_CfgTypeDef structure that contains
* the configuration information for the specified USBx peripheral.
* @retval HAL status
*/
HAL_StatusTypeDef USB_DevInit (USB_OTG_GlobalTypeDef *USBx, USB_OTG_CfgTypeDef cfg)
{
uint32_t index = 0;
/*Activate VBUS Sensing B */
USBx->GCCFG |= USB_OTG_GCCFG_VBDEN;
if (cfg.vbus_sensing_enable == 0)
{
/* Deactivate VBUS Sensing B */
USBx->GCCFG &= ~ USB_OTG_GCCFG_VBDEN;
/* B-peripheral session valid override enable*/
USBx->GOTGCTL |= USB_OTG_GOTGCTL_BVALOEN;
USBx->GOTGCTL |= USB_OTG_GOTGCTL_BVALOVAL;
}
/* Restart the Phy Clock */
USBx_PCGCCTL = 0;
/* Device mode configuration */
USBx_DEVICE->DCFG |= DCFG_FRAME_INTERVAL_80;
/* Set Full speed phy */
USB_SetDevSpeed (USBx , USB_OTG_SPEED_FULL);
/* Flush the FIFOs */
USB_FlushTxFifo(USBx , 0x10); /* all Tx FIFOs */
USB_FlushRxFifo(USBx);
/* Clear all pending Device Interrupts */
USBx_DEVICE->DIEPMSK = 0;
USBx_DEVICE->DOEPMSK = 0;
USBx_DEVICE->DAINT = 0xFFFFFFFF;
USBx_DEVICE->DAINTMSK = 0;
for (index = 0; index < cfg.dev_endpoints; index++)
{
if ((USBx_INEP(index)->DIEPCTL & USB_OTG_DIEPCTL_EPENA) == USB_OTG_DIEPCTL_EPENA)
{
USBx_INEP(index)->DIEPCTL = (USB_OTG_DIEPCTL_EPDIS | USB_OTG_DIEPCTL_SNAK);
}
else
{
USBx_INEP(index)->DIEPCTL = 0;
}
USBx_INEP(index)->DIEPTSIZ = 0;
USBx_INEP(index)->DIEPINT = 0xFF;
}
for (index = 0; index < cfg.dev_endpoints; index++)
{
if ((USBx_OUTEP(index)->DOEPCTL & USB_OTG_DOEPCTL_EPENA) == USB_OTG_DOEPCTL_EPENA)
{
USBx_OUTEP(index)->DOEPCTL = (USB_OTG_DOEPCTL_EPDIS | USB_OTG_DOEPCTL_SNAK);
}
else
{
USBx_OUTEP(index)->DOEPCTL = 0;
}
USBx_OUTEP(index)->DOEPTSIZ = 0;
USBx_OUTEP(index)->DOEPINT = 0xFF;
}
USBx_DEVICE->DIEPMSK &= ~(USB_OTG_DIEPMSK_TXFURM);
if (cfg.dma_enable == 1)
{
/*Set threshold parameters */
USBx_DEVICE->DTHRCTL = (USB_OTG_DTHRCTL_TXTHRLEN_6 | USB_OTG_DTHRCTL_RXTHRLEN_6);
USBx_DEVICE->DTHRCTL |= (USB_OTG_DTHRCTL_RXTHREN | USB_OTG_DTHRCTL_ISOTHREN | USB_OTG_DTHRCTL_NONISOTHREN);
index= USBx_DEVICE->DTHRCTL;
}
/* Disable all interrupts. */
USBx->GINTMSK = 0;
/* Clear any pending interrupts */
USBx->GINTSTS = 0xBFFFFFFF;
/* Enable the common interrupts */
if (cfg.dma_enable == DISABLE)
{
USBx->GINTMSK |= USB_OTG_GINTMSK_RXFLVLM;
}
/* Enable interrupts matching to the Device mode ONLY */
USBx->GINTMSK |= (USB_OTG_GINTMSK_USBSUSPM | USB_OTG_GINTMSK_USBRST |\
USB_OTG_GINTMSK_ENUMDNEM | USB_OTG_GINTMSK_IEPINT |\
USB_OTG_GINTMSK_OEPINT | USB_OTG_GINTMSK_IISOIXFRM|\
USB_OTG_GINTMSK_PXFRM_IISOOXFRM | USB_OTG_GINTMSK_WUIM);
if(cfg.Sof_enable)
{
USBx->GINTMSK |= USB_OTG_GINTMSK_SOFM;
}
if (cfg.vbus_sensing_enable == ENABLE)
{
USBx->GINTMSK |= (USB_OTG_GINTMSK_SRQIM | USB_OTG_GINTMSK_OTGINT);
}
return HAL_OK;
}
/**
* @brief USB_OTG_FlushTxFifo : Flush a Tx FIFO
* @param USBx: Selected device
* @param num: FIFO number
* This parameter can be a value from 1 to 15
15 means Flush all Tx FIFOs
* @retval HAL status
*/
HAL_StatusTypeDef USB_FlushTxFifo (USB_OTG_GlobalTypeDef *USBx, uint32_t num)
{
uint32_t count = 0;
USBx->GRSTCTL = ( USB_OTG_GRSTCTL_TXFFLSH |(uint32_t)( num << 6));
do
{
if (++count > 200000)
{
return HAL_TIMEOUT;
}
}
while ((USBx->GRSTCTL & USB_OTG_GRSTCTL_TXFFLSH) == USB_OTG_GRSTCTL_TXFFLSH);
return HAL_OK;
}
/**
* @brief USB_FlushRxFifo : Flush Rx FIFO
* @param USBx: Selected device
* @retval HAL status
*/
HAL_StatusTypeDef USB_FlushRxFifo(USB_OTG_GlobalTypeDef *USBx)
{
uint32_t count = 0;
USBx->GRSTCTL = USB_OTG_GRSTCTL_RXFFLSH;
do
{
if (++count > 200000)
{
return HAL_TIMEOUT;
}
}
while ((USBx->GRSTCTL & USB_OTG_GRSTCTL_RXFFLSH) == USB_OTG_GRSTCTL_RXFFLSH);
return HAL_OK;
}
/**
* @brief USB_SetDevSpeed :Initializes the DevSpd field of DCFG register
* depending the PHY type and the enumeration speed of the device.
* @param USBx: Selected device
* @param speed: device speed
* This parameter can be one of these values:
* @arg USB_OTG_SPEED_HIGH: High speed mode
* @arg USB_OTG_SPEED_HIGH_IN_FULL: High speed core in Full Speed mode
* @arg USB_OTG_SPEED_FULL: Full speed mode
* @arg USB_OTG_SPEED_LOW: Low speed mode
* @retval Hal status
*/
HAL_StatusTypeDef USB_SetDevSpeed(USB_OTG_GlobalTypeDef *USBx , uint8_t speed)
{
USBx_DEVICE->DCFG |= speed;
return HAL_OK;
}
/**
* @brief USB_GetDevSpeed :Return the Dev Speed
* @param USBx: Selected device
* @retval speed : device speed
* This parameter can be one of these values:
* @arg USB_OTG_SPEED_HIGH: High speed mode
* @arg USB_OTG_SPEED_FULL: Full speed mode
* @arg USB_OTG_SPEED_LOW: Low speed mode
*/
uint8_t USB_GetDevSpeed(USB_OTG_GlobalTypeDef *USBx)
{
uint8_t speed = 0;
if((USBx_DEVICE->DSTS & USB_OTG_DSTS_ENUMSPD) == DSTS_ENUMSPD_HS_PHY_30MHZ_OR_60MHZ)
{
speed = USB_OTG_SPEED_HIGH;
}
else if (((USBx_DEVICE->DSTS & USB_OTG_DSTS_ENUMSPD) == DSTS_ENUMSPD_FS_PHY_30MHZ_OR_60MHZ)||
((USBx_DEVICE->DSTS & USB_OTG_DSTS_ENUMSPD) == DSTS_ENUMSPD_FS_PHY_48MHZ))
{
speed = USB_OTG_SPEED_FULL;
}
else if((USBx_DEVICE->DSTS & USB_OTG_DSTS_ENUMSPD) == DSTS_ENUMSPD_LS_PHY_6MHZ)
{
speed = USB_OTG_SPEED_LOW;
}
return speed;
}
/**
* @brief Activate and configure an endpoint
* @param USBx: Selected device
* @param ep: pointer to endpoint structure
* @retval HAL status
*/
HAL_StatusTypeDef USB_ActivateEndpoint(USB_OTG_GlobalTypeDef *USBx, USB_OTG_EPTypeDef *ep)
{
if (ep->is_in == 1)
{
USBx_DEVICE->DAINTMSK |= USB_OTG_DAINTMSK_IEPM & ((1 << (ep->num)));
if (((USBx_INEP(ep->num)->DIEPCTL) & USB_OTG_DIEPCTL_USBAEP) == 0)
{
USBx_INEP(ep->num)->DIEPCTL |= ((ep->maxpacket & USB_OTG_DIEPCTL_MPSIZ ) | (ep->type << 18 ) |\
((ep->num) << 22 ) | (USB_OTG_DIEPCTL_SD0PID_SEVNFRM) | (USB_OTG_DIEPCTL_USBAEP));
}
}
else
{
USBx_DEVICE->DAINTMSK |= USB_OTG_DAINTMSK_OEPM & ((1 << (ep->num)) << 16);
if (((USBx_OUTEP(ep->num)->DOEPCTL) & USB_OTG_DOEPCTL_USBAEP) == 0)
{
USBx_OUTEP(ep->num)->DOEPCTL |= ((ep->maxpacket & USB_OTG_DOEPCTL_MPSIZ ) | (ep->type << 18 ) |\
(USB_OTG_DIEPCTL_SD0PID_SEVNFRM)| (USB_OTG_DOEPCTL_USBAEP));
}
}
return HAL_OK;
}
/**
* @brief Activate and configure a dedicated endpoint
* @param USBx: Selected device
* @param ep: pointer to endpoint structure
* @retval HAL status
*/
HAL_StatusTypeDef USB_ActivateDedicatedEndpoint(USB_OTG_GlobalTypeDef *USBx, USB_OTG_EPTypeDef *ep)
{
static __IO uint32_t debug = 0;
/* Read DEPCTLn register */
if (ep->is_in == 1)
{
if (((USBx_INEP(ep->num)->DIEPCTL) & USB_OTG_DIEPCTL_USBAEP) == 0)
{
USBx_INEP(ep->num)->DIEPCTL |= ((ep->maxpacket & USB_OTG_DIEPCTL_MPSIZ ) | (ep->type << 18 ) |\
((ep->num) << 22 ) | (USB_OTG_DIEPCTL_SD0PID_SEVNFRM) | (USB_OTG_DIEPCTL_USBAEP));
}
debug |= ((ep->maxpacket & USB_OTG_DIEPCTL_MPSIZ ) | (ep->type << 18 ) |\
((ep->num) << 22 ) | (USB_OTG_DIEPCTL_SD0PID_SEVNFRM) | (USB_OTG_DIEPCTL_USBAEP));
USBx_DEVICE->DEACHMSK |= USB_OTG_DAINTMSK_IEPM & ((1 << (ep->num)));
}
else
{
if (((USBx_OUTEP(ep->num)->DOEPCTL) & USB_OTG_DOEPCTL_USBAEP) == 0)
{
USBx_OUTEP(ep->num)->DOEPCTL |= ((ep->maxpacket & USB_OTG_DOEPCTL_MPSIZ ) | (ep->type << 18 ) |\
((ep->num) << 22 ) | (USB_OTG_DOEPCTL_USBAEP));
debug = (uint32_t)(((uint32_t )USBx) + USB_OTG_OUT_ENDPOINT_BASE + (0)*USB_OTG_EP_REG_SIZE);
debug = (uint32_t )&USBx_OUTEP(ep->num)->DOEPCTL;
debug |= ((ep->maxpacket & USB_OTG_DOEPCTL_MPSIZ ) | (ep->type << 18 ) |\
((ep->num) << 22 ) | (USB_OTG_DOEPCTL_USBAEP));
}
USBx_DEVICE->DEACHMSK |= USB_OTG_DAINTMSK_OEPM & ((1 << (ep->num)) << 16);
}
return HAL_OK;
}
/**
* @brief De-activate and de-initialize an endpoint
* @param USBx: Selected device
* @param ep: pointer to endpoint structure
* @retval HAL status
*/
HAL_StatusTypeDef USB_DeactivateEndpoint(USB_OTG_GlobalTypeDef *USBx, USB_OTG_EPTypeDef *ep)
{
/* Read DEPCTLn register */
if (ep->is_in == 1)
{
USBx_DEVICE->DEACHMSK &= ~(USB_OTG_DAINTMSK_IEPM & ((1 << (ep->num))));
USBx_DEVICE->DAINTMSK &= ~(USB_OTG_DAINTMSK_IEPM & ((1 << (ep->num))));
USBx_INEP(ep->num)->DIEPCTL &= ~ USB_OTG_DIEPCTL_USBAEP;
}
else
{
USBx_DEVICE->DEACHMSK &= ~(USB_OTG_DAINTMSK_OEPM & ((1 << (ep->num)) << 16));
USBx_DEVICE->DAINTMSK &= ~(USB_OTG_DAINTMSK_OEPM & ((1 << (ep->num)) << 16));
USBx_OUTEP(ep->num)->DOEPCTL &= ~USB_OTG_DOEPCTL_USBAEP;
}
return HAL_OK;
}
/**
* @brief De-activate and de-initialize a dedicated endpoint
* @param USBx: Selected device
* @param ep: pointer to endpoint structure
* @retval HAL status
*/
HAL_StatusTypeDef USB_DeactivateDedicatedEndpoint(USB_OTG_GlobalTypeDef *USBx, USB_OTG_EPTypeDef *ep)
{
/* Read DEPCTLn register */
if (ep->is_in == 1)
{
USBx_INEP(ep->num)->DIEPCTL &= ~ USB_OTG_DIEPCTL_USBAEP;
USBx_DEVICE->DAINTMSK &= ~(USB_OTG_DAINTMSK_IEPM & ((1 << (ep->num))));
}
else
{
USBx_OUTEP(ep->num)->DOEPCTL &= ~USB_OTG_DOEPCTL_USBAEP;
USBx_DEVICE->DAINTMSK &= ~(USB_OTG_DAINTMSK_OEPM & ((1 << (ep->num)) << 16));
}
return HAL_OK;
}
/**
* @brief USB_EPStartXfer : setup and starts a transfer over an EP
* @param USBx: Selected device
* @param ep: pointer to endpoint structure
* @param dma: USB dma enabled or disabled
* This parameter can be one of these values:
* 0 : DMA feature not used
* 1 : DMA feature used
* @retval HAL status
*/
HAL_StatusTypeDef USB_EPStartXfer(USB_OTG_GlobalTypeDef *USBx , USB_OTG_EPTypeDef *ep, uint8_t dma)
{
uint16_t pktcnt = 0;
/* IN endpoint */
if (ep->is_in == 1)
{
/* Zero Length Packet? */
if (ep->xfer_len == 0)
{
USBx_INEP(ep->num)->DIEPTSIZ &= ~(USB_OTG_DIEPTSIZ_PKTCNT);
USBx_INEP(ep->num)->DIEPTSIZ |= (USB_OTG_DIEPTSIZ_PKTCNT & (1 << 19)) ;
USBx_INEP(ep->num)->DIEPTSIZ &= ~(USB_OTG_DIEPTSIZ_XFRSIZ);
}
else
{
/* Program the transfer size and packet count
* as follows: xfersize = N * maxpacket +
* short_packet pktcnt = N + (short_packet
* exist ? 1 : 0)
*/
USBx_INEP(ep->num)->DIEPTSIZ &= ~(USB_OTG_DIEPTSIZ_XFRSIZ);
USBx_INEP(ep->num)->DIEPTSIZ &= ~(USB_OTG_DIEPTSIZ_PKTCNT);
USBx_INEP(ep->num)->DIEPTSIZ |= (USB_OTG_DIEPTSIZ_PKTCNT & (((ep->xfer_len + ep->maxpacket -1)/ ep->maxpacket) << 19)) ;
USBx_INEP(ep->num)->DIEPTSIZ |= (USB_OTG_DIEPTSIZ_XFRSIZ & ep->xfer_len);
if (ep->type == EP_TYPE_ISOC)
{
USBx_INEP(ep->num)->DIEPTSIZ &= ~(USB_OTG_DIEPTSIZ_MULCNT);
USBx_INEP(ep->num)->DIEPTSIZ |= (USB_OTG_DIEPTSIZ_MULCNT & (1 << 29));
}
}
if (ep->type != EP_TYPE_ISOC)
{
/* Enable the Tx FIFO Empty Interrupt for this EP */
if (ep->xfer_len > 0)
{
// Added for MBED PR #3062
atomic_set_u32(&USBx_DEVICE->DIEPEMPMSK, 1 << ep->num);
}
}
if (ep->type == EP_TYPE_ISOC)
{
if ((USBx_DEVICE->DSTS & ( 1 << 8 )) == 0)
{
USBx_INEP(ep->num)->DIEPCTL |= USB_OTG_DIEPCTL_SODDFRM;
}
else
{
USBx_INEP(ep->num)->DIEPCTL |= USB_OTG_DIEPCTL_SD0PID_SEVNFRM;
}
}
/* EP enable, IN data in FIFO */
USBx_INEP(ep->num)->DIEPCTL |= (USB_OTG_DIEPCTL_CNAK | USB_OTG_DIEPCTL_EPENA);
if (ep->type == EP_TYPE_ISOC)
{
USB_WritePacket(USBx, ep->xfer_buff, ep->num, ep->xfer_len, dma);
}
}
else /* OUT endpoint */
{
/* Program the transfer size and packet count as follows:
* pktcnt = N
* xfersize = N * maxpacket
*/
USBx_OUTEP(ep->num)->DOEPTSIZ &= ~(USB_OTG_DOEPTSIZ_XFRSIZ);
USBx_OUTEP(ep->num)->DOEPTSIZ &= ~(USB_OTG_DOEPTSIZ_PKTCNT);
if (ep->xfer_len == 0)
{
USBx_OUTEP(ep->num)->DOEPTSIZ |= (USB_OTG_DOEPTSIZ_XFRSIZ & ep->maxpacket);
USBx_OUTEP(ep->num)->DOEPTSIZ |= (USB_OTG_DOEPTSIZ_PKTCNT & (1 << 19)) ;
}
else
{
pktcnt = (ep->xfer_len + ep->maxpacket -1)/ ep->maxpacket;
USBx_OUTEP(ep->num)->DOEPTSIZ |= (USB_OTG_DOEPTSIZ_PKTCNT & (pktcnt << 19)); ;
USBx_OUTEP(ep->num)->DOEPTSIZ |= (USB_OTG_DOEPTSIZ_XFRSIZ & (ep->maxpacket * pktcnt));
}
if (ep->type == EP_TYPE_ISOC)
{
if ((USBx_DEVICE->DSTS & ( 1 << 8 )) == 0)
{
USBx_OUTEP(ep->num)->DOEPCTL |= USB_OTG_DOEPCTL_SODDFRM;
}
else
{
USBx_OUTEP(ep->num)->DOEPCTL |= USB_OTG_DOEPCTL_SD0PID_SEVNFRM;
}
}
/* EP enable */
USBx_OUTEP(ep->num)->DOEPCTL |= (USB_OTG_DOEPCTL_CNAK | USB_OTG_DOEPCTL_EPENA);
}
return HAL_OK;
}
/**
* @brief USB_EP0StartXfer : setup and starts a transfer over the EP 0
* @param USBx: Selected device
* @param ep: pointer to endpoint structure
* @param dma: USB dma enabled or disabled
* This parameter can be one of these values:
* 0 : DMA feature not used
* 1 : DMA feature used
* @retval HAL status
*/
HAL_StatusTypeDef USB_EP0StartXfer(USB_OTG_GlobalTypeDef *USBx , USB_OTG_EPTypeDef *ep, uint8_t dma)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(USBx);
UNUSED(dma);
/* IN endpoint */
if (ep->is_in == 1)
{
/* Zero Length Packet? */
if (ep->xfer_len == 0)
{
USBx_INEP(ep->num)->DIEPTSIZ &= ~(USB_OTG_DIEPTSIZ_PKTCNT);
USBx_INEP(ep->num)->DIEPTSIZ |= (USB_OTG_DIEPTSIZ_PKTCNT & (1 << 19)) ;
USBx_INEP(ep->num)->DIEPTSIZ &= ~(USB_OTG_DIEPTSIZ_XFRSIZ);
}
else
{
/* Program the transfer size and packet count
* as follows: xfersize = N * maxpacket +
* short_packet pktcnt = N + (short_packet
* exist ? 1 : 0)
*/
USBx_INEP(ep->num)->DIEPTSIZ &= ~(USB_OTG_DIEPTSIZ_XFRSIZ);
USBx_INEP(ep->num)->DIEPTSIZ &= ~(USB_OTG_DIEPTSIZ_PKTCNT);
if(ep->xfer_len > ep->maxpacket)
{
ep->xfer_len = ep->maxpacket;
}
USBx_INEP(ep->num)->DIEPTSIZ |= (USB_OTG_DIEPTSIZ_PKTCNT & (1 << 19)) ;
USBx_INEP(ep->num)->DIEPTSIZ |= (USB_OTG_DIEPTSIZ_XFRSIZ & ep->xfer_len);
}
/* Enable the Tx FIFO Empty Interrupt for this EP */
if (ep->xfer_len > 0)
{
// Added for MBED PR #3062
atomic_set_u32(&USBx_DEVICE->DIEPEMPMSK, 1 << (ep->num));
}
/* EP enable, IN data in FIFO */
USBx_INEP(ep->num)->DIEPCTL |= (USB_OTG_DIEPCTL_CNAK | USB_OTG_DIEPCTL_EPENA);
}
else /* OUT endpoint */
{
/* Program the transfer size and packet count as follows:
* pktcnt = N
* xfersize = N * maxpacket
*/
USBx_OUTEP(ep->num)->DOEPTSIZ &= ~(USB_OTG_DOEPTSIZ_XFRSIZ);
USBx_OUTEP(ep->num)->DOEPTSIZ &= ~(USB_OTG_DOEPTSIZ_PKTCNT);
if (ep->xfer_len > 0)
{
ep->xfer_len = ep->maxpacket;
}
USBx_OUTEP(ep->num)->DOEPTSIZ |= (USB_OTG_DOEPTSIZ_PKTCNT & (1 << 19));
USBx_OUTEP(ep->num)->DOEPTSIZ |= (USB_OTG_DOEPTSIZ_XFRSIZ & (ep->maxpacket));
/* EP enable */
USBx_OUTEP(ep->num)->DOEPCTL |= (USB_OTG_DOEPCTL_CNAK | USB_OTG_DOEPCTL_EPENA);
}
return HAL_OK;
}
/**
* @brief USB_WritePacket : Writes a packet into the Tx FIFO associated
* with the EP/channel
* @param USBx: Selected device
* @param src: pointer to source buffer
* @param ch_ep_num: endpoint or host channel number
* @param len: Number of bytes to write
* @param dma: USB dma enabled or disabled
* This parameter can be one of these values:
* 0 : DMA feature not used
* 1 : DMA feature used
* @retval HAL status
*/
HAL_StatusTypeDef USB_WritePacket(USB_OTG_GlobalTypeDef *USBx, uint8_t *src, uint8_t ch_ep_num, uint16_t len, uint8_t dma)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(USBx);
UNUSED(dma);
uint32_t count32b= 0 , index= 0;
count32b = (len + 3) / 4;
for (index = 0; index < count32b; index++, src += 4)
{
USBx_DFIFO(ch_ep_num) = *((__packed uint32_t *)src);
}
return HAL_OK;
}
/**
* @brief USB_ReadPacket : read a packet from the Tx FIFO associated
* with the EP/channel
* @param USBx: Selected device
* @param src: source pointer
* @param ch_ep_num: endpoint or host channel number
* @param len: Number of bytes to read
* @param dma: USB dma enabled or disabled
* This parameter can be one of these values:
* 0 : DMA feature not used
* 1 : DMA feature used
* @retval pointer to destination buffer
*/
void *USB_ReadPacket(USB_OTG_GlobalTypeDef *USBx, uint8_t *dest, uint16_t len)
{
uint32_t index=0;
uint32_t count32b = (len + 3) / 4;
for ( index = 0; index < count32b; index++, dest += 4 )
{
*(__packed uint32_t *)dest = USBx_DFIFO(0);
}
return ((void *)dest);
}
/**
* @brief USB_EPSetStall : set a stall condition over an EP
* @param USBx: Selected device
* @param ep: pointer to endpoint structure
* @retval HAL status
*/
HAL_StatusTypeDef USB_EPSetStall(USB_OTG_GlobalTypeDef *USBx , USB_OTG_EPTypeDef *ep)
{
if (ep->is_in == 1)
{
if (((USBx_INEP(ep->num)->DIEPCTL) & USB_OTG_DIEPCTL_EPENA) == 0)
{
USBx_INEP(ep->num)->DIEPCTL &= ~(USB_OTG_DIEPCTL_EPDIS);
}
USBx_INEP(ep->num)->DIEPCTL |= USB_OTG_DIEPCTL_STALL;
}
else
{
if (((USBx_OUTEP(ep->num)->DOEPCTL) & USB_OTG_DOEPCTL_EPENA) == 0)
{
USBx_OUTEP(ep->num)->DOEPCTL &= ~(USB_OTG_DOEPCTL_EPDIS);
}
USBx_OUTEP(ep->num)->DOEPCTL |= USB_OTG_DOEPCTL_STALL;
}
return HAL_OK;
}
/**
* @brief USB_EPClearStall : Clear a stall condition over an EP
* @param USBx: Selected device
* @param ep: pointer to endpoint structure
* @retval HAL status
*/
HAL_StatusTypeDef USB_EPClearStall(USB_OTG_GlobalTypeDef *USBx, USB_OTG_EPTypeDef *ep)
{
if (ep->is_in == 1)
{
USBx_INEP(ep->num)->DIEPCTL &= ~USB_OTG_DIEPCTL_STALL;
if (ep->type == EP_TYPE_INTR || ep->type == EP_TYPE_BULK)
{
USBx_INEP(ep->num)->DIEPCTL |= USB_OTG_DIEPCTL_SD0PID_SEVNFRM; /* DATA0 */
}
}
else
{
USBx_OUTEP(ep->num)->DOEPCTL &= ~USB_OTG_DOEPCTL_STALL;
if (ep->type == EP_TYPE_INTR || ep->type == EP_TYPE_BULK)
{
USBx_OUTEP(ep->num)->DOEPCTL |= USB_OTG_DOEPCTL_SD0PID_SEVNFRM; /* DATA0 */
}
}
return HAL_OK;
}
/**
* @brief USB_StopDevice : Stop the USB device mode
* @param USBx: Selected device
* @retval HAL status
*/
HAL_StatusTypeDef USB_StopDevice(USB_OTG_GlobalTypeDef *USBx)
{
uint32_t index;
/* Clear Pending interrupt */
for (index = 0; index < 15 ; index++)
{
USBx_INEP(index)->DIEPINT = 0xFF;
USBx_OUTEP(index)->DOEPINT = 0xFF;
}
USBx_DEVICE->DAINT = 0xFFFFFFFF;
/* Clear interrupt masks */
USBx_DEVICE->DIEPMSK = 0;
USBx_DEVICE->DOEPMSK = 0;
USBx_DEVICE->DAINTMSK = 0;
/* Flush the FIFO */
USB_FlushRxFifo(USBx);
USB_FlushTxFifo(USBx , 0x10 );
return HAL_OK;
}
/**
* @brief USB_SetDevAddress : Stop the USB device mode
* @param USBx: Selected device
* @param address: new device address to be assigned
* This parameter can be a value from 0 to 255
* @retval HAL status
*/
HAL_StatusTypeDef USB_SetDevAddress (USB_OTG_GlobalTypeDef *USBx, uint8_t address)
{
USBx_DEVICE->DCFG &= ~ (USB_OTG_DCFG_DAD);
USBx_DEVICE->DCFG |= (address << 4) & USB_OTG_DCFG_DAD ;
return HAL_OK;
}
/**
* @brief USB_DevConnect : Connect the USB device by enabling the pull-up/pull-down
* @param USBx: Selected device
* @retval HAL status
*/
HAL_StatusTypeDef USB_DevConnect (USB_OTG_GlobalTypeDef *USBx)
{
USBx_DEVICE->DCTL &= ~USB_OTG_DCTL_SDIS ;
HAL_Delay(3);
return HAL_OK;
}
/**
* @brief USB_DevDisconnect : Disconnect the USB device by disabling the pull-up/pull-down
* @param USBx: Selected device
* @retval HAL status
*/
HAL_StatusTypeDef USB_DevDisconnect (USB_OTG_GlobalTypeDef *USBx)
{
USBx_DEVICE->DCTL |= USB_OTG_DCTL_SDIS ;
HAL_Delay(3);
return HAL_OK;
}
/**
* @brief USB_ReadInterrupts: return the global USB interrupt status
* @param USBx: Selected device
* @retval HAL status
*/
uint32_t USB_ReadInterrupts (USB_OTG_GlobalTypeDef *USBx)
{
uint32_t tmpreg = 0;
tmpreg = USBx->GINTSTS;
tmpreg &= USBx->GINTMSK;
return tmpreg;
}
/**
* @brief USB_ReadDevAllOutEpInterrupt: return the USB device OUT endpoints interrupt status
* @param USBx: Selected device
* @retval HAL status
*/
uint32_t USB_ReadDevAllOutEpInterrupt (USB_OTG_GlobalTypeDef *USBx)
{
uint32_t tmpreg;
tmpreg = USBx_DEVICE->DAINT;
tmpreg &= USBx_DEVICE->DAINTMSK;
return ((tmpreg & 0xffff0000) >> 16);
}
/**
* @brief USB_ReadDevAllInEpInterrupt: return the USB device IN endpoints interrupt status
* @param USBx: Selected device
* @retval HAL status
*/
uint32_t USB_ReadDevAllInEpInterrupt (USB_OTG_GlobalTypeDef *USBx)
{
uint32_t tmpreg;
tmpreg = USBx_DEVICE->DAINT;
tmpreg &= USBx_DEVICE->DAINTMSK;
return ((tmpreg & 0xFFFF));
}
/**
* @brief Returns Device OUT EP Interrupt register
* @param USBx: Selected device
* @param epnum: endpoint number
* This parameter can be a value from 0 to 15
* @retval Device OUT EP Interrupt register
*/
uint32_t USB_ReadDevOutEPInterrupt (USB_OTG_GlobalTypeDef *USBx , uint8_t epnum)
{
uint32_t tmpreg;
tmpreg = USBx_OUTEP(epnum)->DOEPINT;
tmpreg &= USBx_DEVICE->DOEPMSK;
return tmpreg;
}
/**
* @brief Returns Device IN EP Interrupt register
* @param USBx: Selected device
* @param epnum: endpoint number
* This parameter can be a value from 0 to 15
* @retval Device IN EP Interrupt register
*/
uint32_t USB_ReadDevInEPInterrupt (USB_OTG_GlobalTypeDef *USBx , uint8_t epnum)
{
uint32_t tmpreg = 0, msk = 0, emp = 0;
msk = USBx_DEVICE->DIEPMSK;
emp = USBx_DEVICE->DIEPEMPMSK;
msk |= ((emp >> epnum) & 0x1) << 7;
tmpreg = USBx_INEP(epnum)->DIEPINT & msk;
return tmpreg;
}
/**
* @brief USB_ClearInterrupts: clear a USB interrupt
* @param USBx: Selected device
* @param interrupt: interrupt flag
* @retval None
*/
void USB_ClearInterrupts (USB_OTG_GlobalTypeDef *USBx, uint32_t interrupt)
{
USBx->GINTSTS |= interrupt;
}
/**
* @brief Returns USB core mode
* @param USBx: Selected device
* @retval return core mode : Host or Device
* This parameter can be one of these values:
* 0 : Host
* 1 : Device
*/
uint32_t USB_GetMode(USB_OTG_GlobalTypeDef *USBx)
{
return ((USBx->GINTSTS ) & 0x1);
}
/**
* @brief Activate EP0 for Setup transactions
* @param USBx: Selected device
* @retval HAL status
*/
HAL_StatusTypeDef USB_ActivateSetup (USB_OTG_GlobalTypeDef *USBx)
{
/* Set the MPS of the IN EP based on the enumeration speed */
USBx_INEP(0)->DIEPCTL &= ~USB_OTG_DIEPCTL_MPSIZ;
if((USBx_DEVICE->DSTS & USB_OTG_DSTS_ENUMSPD) == DSTS_ENUMSPD_LS_PHY_6MHZ)
{
USBx_INEP(0)->DIEPCTL |= 3;
}
USBx_DEVICE->DCTL |= USB_OTG_DCTL_CGINAK;
return HAL_OK;
}
/**
* @brief Prepare the EP0 to start the first control setup
* @param USBx: Selected device
* @param dma: USB dma enabled or disabled
* This parameter can be one of these values:
* 0 : DMA feature not used
* 1 : DMA feature used
* @param psetup: pointer to setup packet
* @retval HAL status
*/
HAL_StatusTypeDef USB_EP0_OutStart(USB_OTG_GlobalTypeDef *USBx, uint8_t dma, uint8_t *psetup)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(psetup);
USBx_OUTEP(0)->DOEPTSIZ = 0;
USBx_OUTEP(0)->DOEPTSIZ |= (USB_OTG_DOEPTSIZ_PKTCNT & (1 << 19)) ;
USBx_OUTEP(0)->DOEPTSIZ |= (3 * 8);
USBx_OUTEP(0)->DOEPTSIZ |= USB_OTG_DOEPTSIZ_STUPCNT;
return HAL_OK;
}
/**
* @brief USB_HostInit : Initializes the USB OTG controller registers
* for Host mode
* @param USBx: Selected device
* @param cfg: pointer to a USB_OTG_CfgTypeDef structure that contains
* the configuration information for the specified USBx peripheral.
* @retval HAL status
*/
HAL_StatusTypeDef USB_HostInit (USB_OTG_GlobalTypeDef *USBx, USB_OTG_CfgTypeDef cfg)
{
uint32_t index = 0;
/* Restart the Phy Clock */
USBx_PCGCCTL = 0;
/* Disable the FS/LS support mode only */
if((cfg.speed == USB_OTG_SPEED_FULL)&&
(USBx != USB_OTG_FS))
{
USBx_HOST->HCFG |= USB_OTG_HCFG_FSLSS;
}
else
{
USBx_HOST->HCFG &= ~(USB_OTG_HCFG_FSLSS);
}
/* Make sure the FIFOs are flushed. */
USB_FlushTxFifo(USBx, 0x10 ); /* all Tx FIFOs */
USB_FlushRxFifo(USBx);
/* Clear all pending HC Interrupts */
for (index = 0; index < cfg.Host_channels; index++)
{
USBx_HC(index)->HCINT = 0xFFFFFFFF;
USBx_HC(index)->HCINTMSK = 0;
}
/* Enable VBUS driving */
USB_DriveVbus(USBx, 1);
HAL_Delay(200);
/* Disable all interrupts. */
USBx->GINTMSK = 0;
/* Clear any pending interrupts */
USBx->GINTSTS = 0xFFFFFFFF;
/* set Rx FIFO size */
USBx->GRXFSIZ = (uint32_t )0x80;
USBx->DIEPTXF0_HNPTXFSIZ = (uint32_t )(((0x60 << 16)& USB_OTG_NPTXFD) | 0x80);
USBx->HPTXFSIZ = (uint32_t )(((0x40 << 16)& USB_OTG_HPTXFSIZ_PTXFD) | 0xE0);
/* Enable the common interrupts */
if (cfg.dma_enable == DISABLE)
{
USBx->GINTMSK |= USB_OTG_GINTMSK_RXFLVLM;
}
/* Enable interrupts matching to the Host mode ONLY */
USBx->GINTMSK |= (USB_OTG_GINTMSK_PRTIM | USB_OTG_GINTMSK_HCIM |\
USB_OTG_GINTMSK_SOFM |USB_OTG_GINTSTS_DISCINT|\
USB_OTG_GINTMSK_PXFRM_IISOOXFRM | USB_OTG_GINTMSK_WUIM);
return HAL_OK;
}
/**
* @brief USB_InitFSLSPClkSel : Initializes the FSLSPClkSel field of the
* HCFG register on the PHY type and set the right frame interval
* @param USBx: Selected device
* @param freq: clock frequency
* This parameter can be one of these values:
* HCFG_48_MHZ : Full Speed 48 MHz Clock
* HCFG_6_MHZ : Low Speed 6 MHz Clock
* @retval HAL status
*/
HAL_StatusTypeDef USB_InitFSLSPClkSel(USB_OTG_GlobalTypeDef *USBx , uint8_t freq)
{
USBx_HOST->HCFG &= ~(USB_OTG_HCFG_FSLSPCS);
USBx_HOST->HCFG |= (freq & USB_OTG_HCFG_FSLSPCS);
if (freq == HCFG_48_MHZ)
{
USBx_HOST->HFIR = (uint32_t)48000;
}
else if (freq == HCFG_6_MHZ)
{
USBx_HOST->HFIR = (uint32_t)6000;
}
return HAL_OK;
}
/**
* @brief USB_OTG_ResetPort : Reset Host Port
* @param USBx: Selected device
* @retval HAL status
* @note (1)The application must wait at least 10 ms
* before clearing the reset bit.
*/
HAL_StatusTypeDef USB_ResetPort(USB_OTG_GlobalTypeDef *USBx)
{
__IO uint32_t hprt0 = 0;
hprt0 = USBx_HPRT0;
hprt0 &= ~(USB_OTG_HPRT_PENA | USB_OTG_HPRT_PCDET |\
USB_OTG_HPRT_PENCHNG | USB_OTG_HPRT_POCCHNG );
USBx_HPRT0 = (USB_OTG_HPRT_PRST | hprt0);
HAL_Delay (10); /* See Note #1 */
USBx_HPRT0 = ((~USB_OTG_HPRT_PRST) & hprt0);
return HAL_OK;
}
/**
* @brief USB_DriveVbus : activate or de-activate vbus
* @param state: VBUS state
* This parameter can be one of these values:
* 0 : VBUS Active
* 1 : VBUS Inactive
* @retval HAL status
*/
HAL_StatusTypeDef USB_DriveVbus (USB_OTG_GlobalTypeDef *USBx, uint8_t state)
{
__IO uint32_t hprt0 = 0;
hprt0 = USBx_HPRT0;
hprt0 &= ~(USB_OTG_HPRT_PENA | USB_OTG_HPRT_PCDET |\
USB_OTG_HPRT_PENCHNG | USB_OTG_HPRT_POCCHNG );
if (((hprt0 & USB_OTG_HPRT_PPWR) == 0 ) && (state == 1 ))
{
USBx_HPRT0 = (USB_OTG_HPRT_PPWR | hprt0);
}
if (((hprt0 & USB_OTG_HPRT_PPWR) == USB_OTG_HPRT_PPWR) && (state == 0 ))
{
USBx_HPRT0 = ((~USB_OTG_HPRT_PPWR) & hprt0);
}
return HAL_OK;
}
/**
* @brief Return Host Core speed
* @param USBx: Selected device
* @retval speed : Host speed
* This parameter can be one of these values:
* @arg USB_OTG_SPEED_HIGH: High speed mode
* @arg USB_OTG_SPEED_FULL: Full speed mode
* @arg USB_OTG_SPEED_LOW: Low speed mode
*/
uint32_t USB_GetHostSpeed (USB_OTG_GlobalTypeDef *USBx)
{
__IO uint32_t hprt0 = 0;
hprt0 = USBx_HPRT0;
return ((hprt0 & USB_OTG_HPRT_PSPD) >> 17);
}
/**
* @brief Return Host Current Frame number
* @param USBx: Selected device
* @retval current frame number
*/
uint32_t USB_GetCurrentFrame (USB_OTG_GlobalTypeDef *USBx)
{
return (USBx_HOST->HFNUM & USB_OTG_HFNUM_FRNUM);
}
/**
* @brief Initialize a host channel
* @param USBx: Selected device
* @param ch_num : Channel number
* This parameter can be a value from 1 to 15
* @param epnum: Endpoint number
* This parameter can be a value from 1 to 15
* @param dev_address: Current device address
* This parameter can be a value from 0 to 255
* @param speed: Current device speed
* This parameter can be one of these values:
* @arg USB_OTG_SPEED_HIGH: High speed mode
* @arg USB_OTG_SPEED_FULL: Full speed mode
* @arg USB_OTG_SPEED_LOW: Low speed mode
* @param ep_type: Endpoint Type
* This parameter can be one of these values:
* @arg EP_TYPE_CTRL: Control type
* @arg EP_TYPE_ISOC: Isochronous type
* @arg EP_TYPE_BULK: Bulk type
* @arg EP_TYPE_INTR: Interrupt type
* @param mps: Max Packet Size
* This parameter can be a value from 0 to32K
* @retval HAL state
*/
HAL_StatusTypeDef USB_HC_Init(USB_OTG_GlobalTypeDef *USBx,
uint8_t ch_num,
uint8_t epnum,
uint8_t dev_address,
uint8_t speed,
uint8_t ep_type,
uint16_t mps)
{
/* Clear old interrupt conditions for this host channel. */
USBx_HC(ch_num)->HCINT = 0xFFFFFFFF;
/* Enable channel interrupts required for this transfer. */
switch (ep_type)
{
case EP_TYPE_CTRL:
case EP_TYPE_BULK:
USBx_HC(ch_num)->HCINTMSK = USB_OTG_HCINTMSK_XFRCM |\
USB_OTG_HCINTMSK_STALLM |\
USB_OTG_HCINTMSK_TXERRM |\
USB_OTG_HCINTMSK_DTERRM |\
USB_OTG_HCINTMSK_AHBERR |\
USB_OTG_HCINTMSK_NAKM ;
if (epnum & 0x80)
{
USBx_HC(ch_num)->HCINTMSK |= USB_OTG_HCINTMSK_BBERRM;
}
break;
case EP_TYPE_INTR:
USBx_HC(ch_num)->HCINTMSK = USB_OTG_HCINTMSK_XFRCM |\
USB_OTG_HCINTMSK_STALLM |\
USB_OTG_HCINTMSK_TXERRM |\
USB_OTG_HCINTMSK_DTERRM |\
USB_OTG_HCINTMSK_NAKM |\
USB_OTG_HCINTMSK_AHBERR |\
USB_OTG_HCINTMSK_FRMORM ;
if (epnum & 0x80)
{
USBx_HC(ch_num)->HCINTMSK |= USB_OTG_HCINTMSK_BBERRM;
}
break;
case EP_TYPE_ISOC:
USBx_HC(ch_num)->HCINTMSK = USB_OTG_HCINTMSK_XFRCM |\
USB_OTG_HCINTMSK_ACKM |\
USB_OTG_HCINTMSK_AHBERR |\
USB_OTG_HCINTMSK_FRMORM ;
if (epnum & 0x80)
{
USBx_HC(ch_num)->HCINTMSK |= (USB_OTG_HCINTMSK_TXERRM | USB_OTG_HCINTMSK_BBERRM);
}
break;
}
/* Enable the top level host channel interrupt. */
USBx_HOST->HAINTMSK |= (1 << ch_num);
/* Make sure host channel interrupts are enabled. */
USBx->GINTMSK |= USB_OTG_GINTMSK_HCIM;
/* Program the HCCHAR register */
USBx_HC(ch_num)->HCCHAR = (((dev_address << 22) & USB_OTG_HCCHAR_DAD) |\
(((epnum & 0x7F)<< 11) & USB_OTG_HCCHAR_EPNUM)|\
((((epnum & 0x80) == 0x80)<< 15) & USB_OTG_HCCHAR_EPDIR)|\
(((speed == HPRT0_PRTSPD_LOW_SPEED)<< 17) & USB_OTG_HCCHAR_LSDEV)|\
((ep_type << 18) & USB_OTG_HCCHAR_EPTYP)|\
(mps & USB_OTG_HCCHAR_MPSIZ));
if (ep_type == EP_TYPE_INTR)
{
USBx_HC(ch_num)->HCCHAR |= USB_OTG_HCCHAR_ODDFRM ;
}
return HAL_OK;
}
/**
* @brief Start a transfer over a host channel
* @param USBx: Selected device
* @param hc: pointer to host channel structure
* @param dma: USB dma enabled or disabled
* This parameter can be one of these values:
* 0 : DMA feature not used
* 1 : DMA feature used
* @retval HAL state
*/
#if defined (__CC_ARM) /*!< ARM Compiler */
#pragma O0
#elif defined (__GNUC__) /*!< GNU Compiler */
#pragma GCC optimize ("O0")
#endif /* __CC_ARM */
HAL_StatusTypeDef USB_HC_StartXfer(USB_OTG_GlobalTypeDef *USBx, USB_OTG_HCTypeDef *hc, uint8_t dma)
{
uint8_t is_oddframe = 0;
uint16_t len_words = 0;
uint16_t num_packets = 0;
uint16_t max_hc_pkt_count = 256;
uint32_t tmpreg = 0;
/* Compute the expected number of packets associated to the transfer */
if (hc->xfer_len > 0)
{
num_packets = (hc->xfer_len + hc->max_packet - 1) / hc->max_packet;
if (num_packets > max_hc_pkt_count)
{
num_packets = max_hc_pkt_count;
hc->xfer_len = num_packets * hc->max_packet;
}
}
else
{
num_packets = 1;
}
if (hc->ep_is_in)
{
hc->xfer_len = num_packets * hc->max_packet;
}
/* Initialize the HCTSIZn register */
USBx_HC(hc->ch_num)->HCTSIZ = (((hc->xfer_len) & USB_OTG_HCTSIZ_XFRSIZ)) |\
((num_packets << 19) & USB_OTG_HCTSIZ_PKTCNT) |\
(((hc->data_pid) << 29) & USB_OTG_HCTSIZ_DPID);
if (dma)
{
/* xfer_buff MUST be 32-bits aligned */
USBx_HC(hc->ch_num)->HCDMA = (uint32_t)hc->xfer_buff;
}
is_oddframe = (USBx_HOST->HFNUM & 0x01) ? 0 : 1;
USBx_HC(hc->ch_num)->HCCHAR &= ~USB_OTG_HCCHAR_ODDFRM;
USBx_HC(hc->ch_num)->HCCHAR |= (is_oddframe << 29);
/* Set host channel enable */
tmpreg = USBx_HC(hc->ch_num)->HCCHAR;
tmpreg &= ~USB_OTG_HCCHAR_CHDIS;
tmpreg |= USB_OTG_HCCHAR_CHENA;
USBx_HC(hc->ch_num)->HCCHAR = tmpreg;
if (dma == 0) /* Slave mode */
{
if((hc->ep_is_in == 0) && (hc->xfer_len > 0))
{
switch(hc->ep_type)
{
/* Non periodic transfer */
case EP_TYPE_CTRL:
case EP_TYPE_BULK:
len_words = (hc->xfer_len + 3) / 4;
/* check if there is enough space in FIFO space */
if(len_words > (USBx->HNPTXSTS & 0xFFFF))
{
/* need to process data in nptxfempty interrupt */
USBx->GINTMSK |= USB_OTG_GINTMSK_NPTXFEM;
}
break;
/* Periodic transfer */
case EP_TYPE_INTR:
case EP_TYPE_ISOC:
len_words = (hc->xfer_len + 3) / 4;
/* check if there is enough space in FIFO space */
if(len_words > (USBx_HOST->HPTXSTS & 0xFFFF)) /* split the transfer */
{
/* need to process data in ptxfempty interrupt */
USBx->GINTMSK |= USB_OTG_GINTMSK_PTXFEM;
}
break;
default:
break;
}
/* Write packet into the Tx FIFO. */
USB_WritePacket(USBx, hc->xfer_buff, hc->ch_num, hc->xfer_len, 0);
// Added for MBED PR #3432
hc->xfer_count = hc->xfer_len;
}
}
return HAL_OK;
}
/**
* @brief Read all host channel interrupts status
* @param USBx: Selected device
* @retval HAL state
*/
uint32_t USB_HC_ReadInterrupt (USB_OTG_GlobalTypeDef *USBx)
{
return ((USBx_HOST->HAINT) & 0xFFFF);
}
/**
* @brief Halt a host channel
* @param USBx: Selected device
* @param hc_num: Host Channel number
* This parameter can be a value from 1 to 15
* @retval HAL state
*/
HAL_StatusTypeDef USB_HC_Halt(USB_OTG_GlobalTypeDef *USBx , uint8_t hc_num)
{
uint32_t count = 0;
/* Check for space in the request queue to issue the halt. */
if (((USBx_HC(hc_num)->HCCHAR) & (HCCHAR_CTRL << 18)) || ((USBx_HC(hc_num)->HCCHAR) & (HCCHAR_BULK << 18)))
{
USBx_HC(hc_num)->HCCHAR |= USB_OTG_HCCHAR_CHDIS;
if ((USBx->HNPTXSTS & 0xFFFF) == 0)
{
USBx_HC(hc_num)->HCCHAR &= ~USB_OTG_HCCHAR_CHENA;
USBx_HC(hc_num)->HCCHAR |= USB_OTG_HCCHAR_CHENA;
USBx_HC(hc_num)->HCCHAR &= ~USB_OTG_HCCHAR_EPDIR;
do
{
if (++count > 1000)
{
break;
}
}
while ((USBx_HC(hc_num)->HCCHAR & USB_OTG_HCCHAR_CHENA) == USB_OTG_HCCHAR_CHENA);
}
else
{
USBx_HC(hc_num)->HCCHAR |= USB_OTG_HCCHAR_CHENA;
}
}
else
{
USBx_HC(hc_num)->HCCHAR |= USB_OTG_HCCHAR_CHDIS;
if ((USBx_HOST->HPTXSTS & 0xFFFF) == 0)
{
USBx_HC(hc_num)->HCCHAR &= ~USB_OTG_HCCHAR_CHENA;
USBx_HC(hc_num)->HCCHAR |= USB_OTG_HCCHAR_CHENA;
USBx_HC(hc_num)->HCCHAR &= ~USB_OTG_HCCHAR_EPDIR;
do
{
if (++count > 1000)
{
break;
}
}
while ((USBx_HC(hc_num)->HCCHAR & USB_OTG_HCCHAR_CHENA) == USB_OTG_HCCHAR_CHENA);
}
else
{
USBx_HC(hc_num)->HCCHAR |= USB_OTG_HCCHAR_CHENA;
}
}
return HAL_OK;
}
/**
* @brief Initiate Do Ping protocol
* @param USBx: Selected device
* @param hc_num: Host Channel number
* This parameter can be a value from 1 to 15
* @retval HAL state
*/
HAL_StatusTypeDef USB_DoPing(USB_OTG_GlobalTypeDef *USBx , uint8_t ch_num)
{
uint8_t num_packets = 1;
uint32_t tmpreg = 0;
USBx_HC(ch_num)->HCTSIZ = ((num_packets << 19) & USB_OTG_HCTSIZ_PKTCNT) |\
USB_OTG_HCTSIZ_DOPING;
/* Set host channel enable */
tmpreg = USBx_HC(ch_num)->HCCHAR;
tmpreg &= ~USB_OTG_HCCHAR_CHDIS;
tmpreg |= USB_OTG_HCCHAR_CHENA;
USBx_HC(ch_num)->HCCHAR = tmpreg;
return HAL_OK;
}
/**
* @brief Stop Host Core
* @param USBx: Selected device
* @retval HAL state
*/
HAL_StatusTypeDef USB_StopHost(USB_OTG_GlobalTypeDef *USBx)
{
uint8_t index;
uint32_t count = 0;
uint32_t value = 0;
USB_DisableGlobalInt(USBx);
/* Flush FIFO */
USB_FlushTxFifo(USBx, 0x10);
USB_FlushRxFifo(USBx);
/* Flush out any leftover queued requests. */
for (index = 0; index <= 15; index++)
{
value = USBx_HC(index)->HCCHAR;
value |= USB_OTG_HCCHAR_CHDIS;
value &= ~USB_OTG_HCCHAR_CHENA;
value &= ~USB_OTG_HCCHAR_EPDIR;
USBx_HC(index)->HCCHAR = value;
}
/* Halt all channels to put them into a known state. */
for (index = 0; index <= 15; index++)
{
value = USBx_HC(index)->HCCHAR ;
value |= USB_OTG_HCCHAR_CHDIS;
value |= USB_OTG_HCCHAR_CHENA;
value &= ~USB_OTG_HCCHAR_EPDIR;
USBx_HC(index)->HCCHAR = value;
USBx_HC(index)->HCCHAR = value;
do
{
if (++count > 1000)
{
break;
}
}
while ((USBx_HC(index)->HCCHAR & USB_OTG_HCCHAR_CHENA) == USB_OTG_HCCHAR_CHENA);
}
/* Clear any pending Host interrupts */
USBx_HOST->HAINT = 0xFFFFFFFF;
USBx->GINTSTS = 0xFFFFFFFF;
USB_EnableGlobalInt(USBx);
return HAL_OK;
}
/**
* @brief USB_ActivateRemoteWakeup : active remote wakeup signalling
* @param USBx : Selected device
* @retval HAL status
*/
HAL_StatusTypeDef USB_ActivateRemoteWakeup(USB_OTG_GlobalTypeDef *USBx)
{
if((USBx_DEVICE->DSTS & USB_OTG_DSTS_SUSPSTS) == USB_OTG_DSTS_SUSPSTS)
{
/* active Remote wakeup signalling */
USBx_DEVICE->DCTL |= USB_OTG_DCTL_RWUSIG;
}
return HAL_OK;
}
/**
* @brief USB_DeActivateRemoteWakeup : de-active remote wakeup signalling
* @param USBx : Selected device
* @retval HAL status
*/
HAL_StatusTypeDef USB_DeActivateRemoteWakeup(USB_OTG_GlobalTypeDef *USBx)
{
/* active Remote wakeup signalling */
USBx_DEVICE->DCTL &= ~(USB_OTG_DCTL_RWUSIG);
return HAL_OK;
}
#endif /* USB_OTG_FS */
/*==============================================================================
USB Device FS peripheral available on STM32L432xx, STM32L433xx, STM32L442xx)
and STM32L443xx devices
==============================================================================*/
#if defined (USB)
/**
* @brief Initializes the USB Core
* @param USBx: USB Instance
* @param cfg : pointer to a USB_CfgTypeDef structure that contains
* the configuration information for the specified USBx peripheral.
* @retval HAL status
*/
HAL_StatusTypeDef USB_CoreInit(USB_TypeDef *USBx, USB_CfgTypeDef cfg)
{
/* NOTE : - This function is not required by USB Device FS peripheral, it is used
only by USB OTG FS peripheral.
- This function is added to ensure compatibility across platforms.
*/
/* Prevent unused argument(s) compilation warning */
UNUSED(USBx);
UNUSED(cfg);
return HAL_OK;
}
/**
* @brief USB_EnableGlobalInt
* Enables the controller's Global Int in the AHB Config reg
* @param USBx : Selected device
* @retval HAL status
*/
HAL_StatusTypeDef USB_EnableGlobalInt(USB_TypeDef *USBx)
{
uint32_t winterruptmask = 0;
/* Set winterruptmask variable */
winterruptmask = USB_CNTR_CTRM | USB_CNTR_WKUPM | USB_CNTR_SUSPM | USB_CNTR_ERRM \
| USB_CNTR_ESOFM | USB_CNTR_RESETM;
/* Set interrupt mask */
USBx->CNTR |= winterruptmask;
return HAL_OK;
}
/**
* @brief USB_DisableGlobalInt
* Disable the controller's Global Int in the AHB Config reg
* @param USBx : Selected device
* @retval HAL status
*/
HAL_StatusTypeDef USB_DisableGlobalInt(USB_TypeDef *USBx)
{
uint32_t winterruptmask = 0;
/* Set winterruptmask variable */
winterruptmask = USB_CNTR_CTRM | USB_CNTR_WKUPM | USB_CNTR_SUSPM | USB_CNTR_ERRM \
| USB_CNTR_ESOFM | USB_CNTR_RESETM;
/* Clear interrupt mask */
USBx->CNTR &= ~winterruptmask;
return HAL_OK;
}
/**
* @brief USB_SetCurrentMode : Set functional mode
* @param USBx : Selected device
* @param mode : current core mode
* This parameter can be one of the these values:
* @arg USB_DEVICE_MODE: Peripheral mode mode
* @retval HAL status
*/
HAL_StatusTypeDef USB_SetCurrentMode(USB_TypeDef *USBx , USB_ModeTypeDef mode)
{
/* NOTE : - This function is not required by USB Device FS peripheral, it is used
only by USB OTG FS peripheral.
- This function is added to ensure compatibility across platforms.
*/
/* Prevent unused argument(s) compilation warning */
UNUSED(USBx);
UNUSED(mode);
return HAL_OK;
}
/**
* @brief USB_DevInit : Initializes the USB controller registers
* for device mode
* @param USBx : Selected device
* @param cfg : pointer to a USB_CfgTypeDef structure that contains
* the configuration information for the specified USBx peripheral.
* @retval HAL status
*/
HAL_StatusTypeDef USB_DevInit (USB_TypeDef *USBx, USB_CfgTypeDef cfg)
{
/* Prevent unused argument(s) compilation warning */
UNUSED(cfg);
/* Init Device */
/*CNTR_FRES = 1*/
USBx->CNTR = USB_CNTR_FRES;
/*CNTR_FRES = 0*/
USBx->CNTR = 0;
/*Clear pending interrupts*/
USBx->ISTR = 0;
/*Set Btable Address*/
USBx->BTABLE = BTABLE_ADDRESS;
return HAL_OK;
}
/**
* @brief USB_FlushTxFifo : Flush a Tx FIFO
* @param USBx : Selected device
* @param num : FIFO number
* This parameter can be a value from 1 to 15
15 means Flush all Tx FIFOs
* @retval HAL status
*/
HAL_StatusTypeDef USB_FlushTxFifo (USB_TypeDef *USBx, uint32_t num )
{
/* NOTE : - This function is not required by USB Device FS peripheral, it is used
only by USB OTG FS peripheral.
- This function is added to ensure compatibility across platforms.
*/
/* Prevent unused argument(s) compilation warning */
UNUSED(USBx);
UNUSED(num);
return HAL_OK;
}
/**
* @brief USB_FlushRxFifo : Flush Rx FIFO
* @param USBx : Selected device
* @retval HAL status
*/
HAL_StatusTypeDef USB_FlushRxFifo(USB_TypeDef *USBx)
{
/* NOTE : - This function is not required by USB Device FS peripheral, it is used
only by USB OTG FS peripheral.
- This function is added to ensure compatibility across platforms.
*/
/* Prevent unused argument(s) compilation warning */
UNUSED(USBx);
return HAL_OK;
}
/**
* @brief Activate and configure an endpoint
* @param USBx : Selected device
* @param ep: pointer to endpoint structure
* @retval HAL status
*/
HAL_StatusTypeDef USB_ActivateEndpoint(USB_TypeDef *USBx, USB_EPTypeDef *ep)
{
/* initialize Endpoint */
switch (ep->type)
{
case EP_TYPE_CTRL:
PCD_SET_EPTYPE(USBx, ep->num, USB_EP_CONTROL);
break;
case EP_TYPE_BULK:
PCD_SET_EPTYPE(USBx, ep->num, USB_EP_BULK);
break;
case EP_TYPE_INTR:
PCD_SET_EPTYPE(USBx, ep->num, USB_EP_INTERRUPT);
break;
case EP_TYPE_ISOC:
PCD_SET_EPTYPE(USBx, ep->num, USB_EP_ISOCHRONOUS);
break;
default:
break;
}
PCD_SET_EP_ADDRESS(USBx, ep->num, ep->num);
if (ep->doublebuffer == 0)
{
if (ep->is_in)
{
/*Set the endpoint Transmit buffer address */
PCD_SET_EP_TX_ADDRESS(USBx, ep->num, ep->pmaadress);
PCD_CLEAR_TX_DTOG(USBx, ep->num);
/* Configure NAK status for the Endpoint*/
PCD_SET_EP_TX_STATUS(USBx, ep->num, USB_EP_TX_NAK);
}
else
{
/*Set the endpoint Receive buffer address */
PCD_SET_EP_RX_ADDRESS(USBx, ep->num, ep->pmaadress);
/*Set the endpoint Receive buffer counter*/
PCD_SET_EP_RX_CNT(USBx, ep->num, ep->maxpacket);
PCD_CLEAR_RX_DTOG(USBx, ep->num);
/* Configure VALID status for the Endpoint*/
PCD_SET_EP_RX_STATUS(USBx, ep->num, USB_EP_RX_VALID);
}
}
/*Double Buffer*/
else
{
/*Set the endpoint as double buffered*/
PCD_SET_EP_DBUF(USBx, ep->num);
/*Set buffer address for double buffered mode*/
PCD_SET_EP_DBUF_ADDR(USBx, ep->num,ep->pmaaddr0, ep->pmaaddr1);
if (ep->is_in==0)
{
/* Clear the data toggle bits for the endpoint IN/OUT*/
PCD_CLEAR_RX_DTOG(USBx, ep->num);
PCD_CLEAR_TX_DTOG(USBx, ep->num);
/* Reset value of the data toggle bits for the endpoint out*/
PCD_TX_DTOG(USBx, ep->num);
PCD_SET_EP_RX_STATUS(USBx, ep->num, USB_EP_RX_VALID);
PCD_SET_EP_TX_STATUS(USBx, ep->num, USB_EP_TX_DIS);
}
else
{
/* Clear the data toggle bits for the endpoint IN/OUT*/
PCD_CLEAR_RX_DTOG(USBx, ep->num);
PCD_CLEAR_TX_DTOG(USBx, ep->num);
PCD_RX_DTOG(USBx, ep->num);
/* Configure DISABLE status for the Endpoint*/
PCD_SET_EP_TX_STATUS(USBx, ep->num, USB_EP_TX_DIS);
PCD_SET_EP_RX_STATUS(USBx, ep->num, USB_EP_RX_DIS);
}
}
return HAL_OK;
}
/**
* @brief De-activate and de-initialize an endpoint
* @param USBx : Selected device
* @param ep: pointer to endpoint structure
* @retval HAL status
*/
HAL_StatusTypeDef USB_DeactivateEndpoint(USB_TypeDef *USBx, USB_EPTypeDef *ep)
{
if (ep->doublebuffer == 0)
{
if (ep->is_in)
{
PCD_CLEAR_TX_DTOG(USBx, ep->num);
/* Configure DISABLE status for the Endpoint*/
PCD_SET_EP_TX_STATUS(USBx, ep->num, USB_EP_TX_DIS);
}
else
{
PCD_CLEAR_RX_DTOG(USBx, ep->num);
/* Configure DISABLE status for the Endpoint*/
PCD_SET_EP_RX_STATUS(USBx, ep->num, USB_EP_RX_DIS);
}
}
/*Double Buffer*/
else
{
if (ep->is_in==0)
{
/* Clear the data toggle bits for the endpoint IN/OUT*/
PCD_CLEAR_RX_DTOG(USBx, ep->num);
PCD_CLEAR_TX_DTOG(USBx, ep->num);
/* Reset value of the data toggle bits for the endpoint out*/
PCD_TX_DTOG(USBx, ep->num);
PCD_SET_EP_RX_STATUS(USBx, ep->num, USB_EP_RX_DIS);
PCD_SET_EP_TX_STATUS(USBx, ep->num, USB_EP_TX_DIS);
}
else
{
/* Clear the data toggle bits for the endpoint IN/OUT*/
PCD_CLEAR_RX_DTOG(USBx, ep->num);
PCD_CLEAR_TX_DTOG(USBx, ep->num);
PCD_RX_DTOG(USBx, ep->num);
/* Configure DISABLE status for the Endpoint*/
PCD_SET_EP_TX_STATUS(USBx, ep->num, USB_EP_TX_DIS);
PCD_SET_EP_RX_STATUS(USBx, ep->num, USB_EP_RX_DIS);
}
}
return HAL_OK;
}
/**
* @brief USB_EPStartXfer : setup and starts a transfer over an EP
* @param USBx : Selected device
* @param ep: pointer to endpoint structure
* @retval HAL status
*/
HAL_StatusTypeDef USB_EPStartXfer(USB_TypeDef *USBx , USB_EPTypeDef *ep, uint8_t dma)
{
uint16_t pmabuffer = 0;
uint32_t len = ep->xfer_len;
/* IN endpoint */
if (ep->is_in == 1)
{
/*Multi packet transfer*/
if (ep->xfer_len > ep->maxpacket)
{
len=ep->maxpacket;
ep->xfer_len-=len;
}
else
{
len=ep->xfer_len;
ep->xfer_len =0;
}
/* configure and validate Tx endpoint */
if (ep->doublebuffer == 0)
{
USB_WritePMA(USBx, ep->xfer_buff, ep->pmaadress, len);
PCD_SET_EP_TX_CNT(USBx, ep->num, len);
}
else
{
/* Write the data to the USB endpoint */
if (PCD_GET_ENDPOINT(USBx, ep->num)& USB_EP_DTOG_TX)
{
/* Set the Double buffer counter for pmabuffer1 */
PCD_SET_EP_DBUF1_CNT(USBx, ep->num, ep->is_in, len);
pmabuffer = ep->pmaaddr1;
}
else
{
/* Set the Double buffer counter for pmabuffer0 */
PCD_SET_EP_DBUF0_CNT(USBx, ep->num, ep->is_in, len);
pmabuffer = ep->pmaaddr0;
}
USB_WritePMA(USBx, ep->xfer_buff, pmabuffer, len);
PCD_FreeUserBuffer(USBx, ep->num, ep->is_in);
}
PCD_SET_EP_TX_STATUS(USBx, ep->num, USB_EP_TX_VALID);
}
else /* OUT endpoint */
{
/* Multi packet transfer*/
if (ep->xfer_len > ep->maxpacket)
{
len=ep->maxpacket;
ep->xfer_len-=len;
}
else
{
len=ep->xfer_len;
ep->xfer_len =0;
}
/* configure and validate Rx endpoint */
if (ep->doublebuffer == 0)
{
/*Set RX buffer count*/
PCD_SET_EP_RX_CNT(USBx, ep->num, len);
}
else
{
/*Set the Double buffer counter*/
PCD_SET_EP_DBUF1_CNT(USBx, ep->num, ep->is_in, len);
}
PCD_SET_EP_RX_STATUS(USBx, ep->num, USB_EP_RX_VALID);
}
return HAL_OK;
}
/**
* @brief USB_WritePacket : Writes a packet into the Tx FIFO associated
* with the EP/channel
* @param USBx : Selected device
* @param src : pointer to source buffer
* @param ch_ep_num : endpoint or host channel number
* @param len : Number of bytes to write
* @retval HAL status
*/
HAL_StatusTypeDef USB_WritePacket(USB_TypeDef *USBx, uint8_t *src, uint8_t ch_ep_num, uint16_t len)
{
/* NOTE : - This function is not required by USB Device FS peripheral, it is used
only by USB OTG FS peripheral.
- This function is added to ensure compatibility across platforms.
*/
/* Prevent unused argument(s) compilation warning */
UNUSED(USBx);
UNUSED(src);
UNUSED(ch_ep_num);
UNUSED(len);
return HAL_OK;
}
/**
* @brief USB_ReadPacket : read a packet from the Tx FIFO associated
* with the EP/channel
* @param USBx : Selected device
* @param dest : destination pointer
* @param len : Number of bytes to read
* @retval pointer to destination buffer
*/
void *USB_ReadPacket(USB_TypeDef *USBx, uint8_t *dest, uint16_t len)
{
/* NOTE : - This function is not required by USB Device FS peripheral, it is used
only by USB OTG FS peripheral.
- This function is added to ensure compatibility across platforms.
*/
/* Prevent unused argument(s) compilation warning */
UNUSED(USBx);
UNUSED(dest);
UNUSED(len);
return ((void *)NULL);
}
/**
* @brief USB_EPSetStall : set a stall condition over an EP
* @param USBx : Selected device
* @param ep: pointer to endpoint structure
* @retval HAL status
*/
HAL_StatusTypeDef USB_EPSetStall(USB_TypeDef *USBx , USB_EPTypeDef *ep)
{
if (ep->num == 0)
{
/* This macro sets STALL status for RX & TX*/
PCD_SET_EP_TXRX_STATUS(USBx, ep->num, USB_EP_RX_STALL, USB_EP_TX_STALL);
}
else
{
if (ep->is_in)
{
PCD_SET_EP_TX_STATUS(USBx, ep->num , USB_EP_TX_STALL);
}
else
{
PCD_SET_EP_RX_STATUS(USBx, ep->num , USB_EP_RX_STALL);
}
}
return HAL_OK;
}
/**
* @brief USB_EPClearStall : Clear a stall condition over an EP
* @param USBx : Selected device
* @param ep: pointer to endpoint structure
* @retval HAL status
*/
HAL_StatusTypeDef USB_EPClearStall(USB_TypeDef *USBx, USB_EPTypeDef *ep)
{
if (ep->is_in)
{
PCD_CLEAR_TX_DTOG(USBx, ep->num);
PCD_SET_EP_TX_STATUS(USBx, ep->num, USB_EP_TX_VALID);
}
else
{
PCD_CLEAR_RX_DTOG(USBx, ep->num);
PCD_SET_EP_RX_STATUS(USBx, ep->num, USB_EP_RX_VALID);
}
return HAL_OK;
}
/**
* @brief USB_StopDevice : Stop the usb device mode
* @param USBx : Selected device
* @retval HAL status
*/
HAL_StatusTypeDef USB_StopDevice(USB_TypeDef *USBx)
{
/* disable all interrupts and force USB reset */
USBx->CNTR = USB_CNTR_FRES;
/* clear interrupt status register */
USBx->ISTR = 0;
/* switch-off device */
USBx->CNTR = (USB_CNTR_FRES | USB_CNTR_PDWN);
return HAL_OK;
}
/**
* @brief USB_SetDevAddress : Stop the usb device mode
* @param USBx : Selected device
* @param address : new device address to be assigned
* This parameter can be a value from 0 to 255
* @retval HAL status
*/
HAL_StatusTypeDef USB_SetDevAddress (USB_TypeDef *USBx, uint8_t address)
{
if(address == 0)
{
/* set device address and enable function */
USBx->DADDR = USB_DADDR_EF;
}
return HAL_OK;
}
/**
* @brief USB_DevConnect : Connect the USB device by enabling the pull-up/pull-down
* @param USBx : Selected device
* @retval HAL status
*/
HAL_StatusTypeDef USB_DevConnect (USB_TypeDef *USBx)
{
/* Enabling DP Pull-Down bit to Connect internal pull-up on USB DP line */
USB->BCDR |= USB_BCDR_DPPU;
return HAL_OK;
}
/**
* @brief USB_DevDisconnect : Disconnect the USB device by disabling the pull-up/pull-down
* @param USBx : Selected device
* @retval HAL status
*/
HAL_StatusTypeDef USB_DevDisconnect (USB_TypeDef *USBx)
{
/* Disable DP Pull-Down bit*/
USB->BCDR &= ~(USB_BCDR_DPPU);
return HAL_OK;
}
/**
* @brief USB_ReadInterrupts: return the global USB interrupt status
* @param USBx : Selected device
* @retval HAL status
*/
uint32_t USB_ReadInterrupts (USB_TypeDef *USBx)
{
uint32_t tmpreg = 0;
tmpreg = USBx->ISTR;
return tmpreg;
}
/**
* @brief USB_ReadDevAllOutEpInterrupt: return the USB device OUT endpoints interrupt status
* @param USBx : Selected device
* @retval HAL status
*/
uint32_t USB_ReadDevAllOutEpInterrupt (USB_TypeDef *USBx)
{
/* NOTE : - This function is not required by USB Device FS peripheral, it is used
only by USB OTG FS peripheral.
- This function is added to ensure compatibility across platforms.
*/
/* Prevent unused argument(s) compilation warning */
UNUSED(USBx);
return (0);
}
/**
* @brief USB_ReadDevAllInEpInterrupt: return the USB device IN endpoints interrupt status
* @param USBx : Selected device
* @retval HAL status
*/
uint32_t USB_ReadDevAllInEpInterrupt (USB_TypeDef *USBx)
{
/* NOTE : - This function is not required by USB Device FS peripheral, it is used
only by USB OTG FS peripheral.
- This function is added to ensure compatibility across platforms.
*/
/* Prevent unused argument(s) compilation warning */
UNUSED(USBx);
return (0);
}
/**
* @brief Returns Device OUT EP Interrupt register
* @param USBx : Selected device
* @param epnum : endpoint number
* This parameter can be a value from 0 to 15
* @retval Device OUT EP Interrupt register
*/
uint32_t USB_ReadDevOutEPInterrupt (USB_TypeDef *USBx , uint8_t epnum)
{
/* NOTE : - This function is not required by USB Device FS peripheral, it is used
only by USB OTG FS peripheral.
- This function is added to ensure compatibility across platforms.
*/
/* Prevent unused argument(s) compilation warning */
UNUSED(USBx);
UNUSED(epnum);
return (0);
}
/**
* @brief Returns Device IN EP Interrupt register
* @param USBx : Selected device
* @param epnum : endpoint number
* This parameter can be a value from 0 to 15
* @retval Device IN EP Interrupt register
*/
uint32_t USB_ReadDevInEPInterrupt (USB_TypeDef *USBx , uint8_t epnum)
{
/* NOTE : - This function is not required by USB Device FS peripheral, it is used
only by USB OTG FS peripheral.
- This function is added to ensure compatibility across platforms.
*/
/* Prevent unused argument(s) compilation warning */
UNUSED(USBx);
UNUSED(epnum);
return (0);
}
/**
* @brief USB_ClearInterrupts: clear a USB interrupt
* @param USBx : Selected device
* @param interrupt : interrupt flag
* @retval None
*/
void USB_ClearInterrupts (USB_TypeDef *USBx, uint32_t interrupt)
{
/* NOTE : - This function is not required by USB Device FS peripheral, it is used
only by USB OTG FS peripheral.
- This function is added to ensure compatibility across platforms.
*/
/* Prevent unused argument(s) compilation warning */
UNUSED(USBx);
UNUSED(interrupt);
}
/**
* @brief Prepare the EP0 to start the first control setup
* @param USBx : Selected device
* @param psetup : pointer to setup packet
* @retval HAL status
*/
HAL_StatusTypeDef USB_EP0_OutStart(USB_TypeDef *USBx, uint8_t dma ,uint8_t *psetup)
{
/* NOTE : - This function is not required by USB Device FS peripheral, it is used
only by USB OTG FS peripheral.
- This function is added to ensure compatibility across platforms.
*/
/* Prevent unused argument(s) compilation warning */
UNUSED(USBx);
UNUSED(psetup);
UNUSED(dma);
return HAL_OK;
}
/**
* @brief USB_ActivateRemoteWakeup : active remote wakeup signalling
* @param USBx : Selected device
* @retval HAL status
*/
HAL_StatusTypeDef USB_ActivateRemoteWakeup(USB_TypeDef *USBx)
{
USBx->CNTR |= USB_CNTR_RESUME;
return HAL_OK;
}
/**
* @brief USB_DeActivateRemoteWakeup : de-active remote wakeup signalling
* @param USBx : Selected device
* @retval HAL status
*/
HAL_StatusTypeDef USB_DeActivateRemoteWakeup(USB_TypeDef *USBx)
{
USBx->CNTR &= ~(USB_CNTR_RESUME);
return HAL_OK;
}
/**
* @brief Copy a buffer from user memory area to packet memory area (PMA)
* @param USBx : pointer to USB register.
* @param pbUsrBuf : pointer to user memory area.
* @param wPMABufAddr : address into PMA.
* @param wNBytes : number of bytes to be copied.
* @retval None
*/
void USB_WritePMA(USB_TypeDef *USBx, uint8_t *pbUsrBuf, uint16_t wPMABufAddr, uint16_t wNBytes)
{
uint32_t n = (wNBytes + 1) >> 1;
uint32_t i;
uint16_t temp1, temp2;
uint16_t *pdwVal;
pdwVal = (uint16_t *)(wPMABufAddr + (uint32_t)USBx + 0x400);
for (i = n; i != 0; i--)
{
temp1 = (uint16_t) * pbUsrBuf;
pbUsrBuf++;
temp2 = temp1 | (uint16_t) * pbUsrBuf << 8;
*pdwVal++ = temp2;
pbUsrBuf++;
}
}
/**
* @brief Copy a buffer from user memory area to packet memory area (PMA)
* @param USBx : pointer to USB register.
* @param pbUsrBuf : pointer to user memory area.
* @param wPMABufAddr : address into PMA.
* @param wNBytes : number of bytes to be copied.
* @retval None
*/
void USB_ReadPMA(USB_TypeDef *USBx, uint8_t *pbUsrBuf, uint16_t wPMABufAddr, uint16_t wNBytes)
{
uint32_t n = (wNBytes + 1) >> 1;
uint32_t i;
uint16_t *pdwVal;
pdwVal = (uint16_t *)(wPMABufAddr + (uint32_t)USBx + 0x400);
for (i = n; i != 0; i--)
{
*(uint16_t*)pbUsrBuf++ = *pdwVal++;
pbUsrBuf++;
}
}
#endif /* USB */
/**
* @}
*/
/**
* @}
*/
#if defined (USB_OTG_FS)
/** @addtogroup USB_LL_Private_Functions
* @{
*/
/**
* @brief Reset the USB Core (needed after USB clock settings change)
* @param USBx : Selected device
* @retval HAL status
*/
static HAL_StatusTypeDef USB_CoreReset(USB_OTG_GlobalTypeDef *USBx)
{
uint32_t count = 0;
/* Wait for AHB master IDLE state. */
do
{
if (++count > 200000)
{
return HAL_TIMEOUT;
}
}
while ((USBx->GRSTCTL & USB_OTG_GRSTCTL_AHBIDL) == 0);
/* Core Soft Reset */
count = 0;
USBx->GRSTCTL |= USB_OTG_GRSTCTL_CSRST;
do
{
if (++count > 200000)
{
return HAL_TIMEOUT;
}
}
while ((USBx->GRSTCTL & USB_OTG_GRSTCTL_CSRST) == USB_OTG_GRSTCTL_CSRST);
return HAL_OK;
}
/**
* @}
*/
#endif /* USB_OTG_FS */
#endif /* STM32L432xx || STM32L433xx || STM32L442xx || STM32L443xx || */
/* STM32L452xx || STM32L462xx || */
/* STM32L475xx || STM32L476xx || STM32L485xx || STM32L486xx || */
/* STM32L496xx || STM32L4A6xx || */
/* STM32L4R5xx || STM32L4R7xx || STM32L4R9xx || STM32L4S5xx || STM32L4S7xx || STM32L4S9xx */
#endif /* defined (HAL_PCD_MODULE_ENABLED) || defined (HAL_HCD_MODULE_ENABLED) */
/**
* @}
*/
/**
* @}
*/
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
