mbed official
mbed library sources. Supersedes mbed-src.
Dependents: Nucleo_Hello_Encoder BLE_iBeaconScan AM1805_DEMO DISCO-F429ZI_ExportTemplate1 ... more
Diff: targets/TARGET_STM/TARGET_STM32H7/device/stm32h7xx_hal_smartcard.h
- Revision:
- 189:f392fc9709a3
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/TARGET_STM/TARGET_STM32H7/device/stm32h7xx_hal_smartcard.h Wed Feb 20 22:31:08 2019 +0000
@@ -0,0 +1,1216 @@
+/**
+ ******************************************************************************
+ * @file stm32h7xx_hal_smartcard.h
+ * @author MCD Application Team
+ * @brief Header file of SMARTCARD HAL module.
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© Copyright (c) 2017 STMicroelectronics.
+ * All rights reserved.</center></h2>
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef STM32H7xx_HAL_SMARTCARD_H
+#define STM32H7xx_HAL_SMARTCARD_H
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32h7xx_hal_def.h"
+
+/** @addtogroup STM32H7xx_HAL_Driver
+ * @{
+ */
+
+/** @addtogroup SMARTCARD
+ * @{
+ */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup SMARTCARD_Exported_Types SMARTCARD Exported Types
+ * @{
+ */
+
+/**
+ * @brief SMARTCARD Init Structure definition
+ */
+typedef struct
+{
+ uint32_t BaudRate; /*!< Configures the SmartCard communication baud rate.
+ The baud rate register is computed using the following formula:
+ Baud Rate Register = ((usart_ker_ckpres) / ((hsmartcard->Init.BaudRate)))
+ where usart_ker_ckpres is the USART input clock divided by a prescaler */
+
+ uint32_t WordLength; /*!< Specifies the number of data bits transmitted or received in a frame.
+ This parameter @ref SMARTCARD_Word_Length can only be set to 9 (8 data + 1 parity bits). */
+
+ uint32_t StopBits; /*!< Specifies the number of stop bits.
+ This parameter can be a value of @ref SMARTCARD_Stop_Bits. */
+
+ uint16_t Parity; /*!< Specifies the parity mode.
+ This parameter can be a value of @ref SMARTCARD_Parity
+ @note The parity is enabled by default (PCE is forced to 1).
+ Since the WordLength is forced to 8 bits + parity, M is
+ forced to 1 and the parity bit is the 9th bit. */
+
+ uint16_t Mode; /*!< Specifies whether the Receive or Transmit mode is enabled or disabled.
+ This parameter can be a value of @ref SMARTCARD_Mode */
+
+ uint16_t CLKPolarity; /*!< Specifies the steady state of the serial clock.
+ This parameter can be a value of @ref SMARTCARD_Clock_Polarity */
+
+ uint16_t CLKPhase; /*!< Specifies the clock transition on which the bit capture is made.
+ This parameter can be a value of @ref SMARTCARD_Clock_Phase */
+
+ uint16_t CLKLastBit; /*!< Specifies whether the clock pulse corresponding to the last transmitted
+ data bit (MSB) has to be output on the SCLK pin in synchronous mode.
+ This parameter can be a value of @ref SMARTCARD_Last_Bit */
+
+ uint16_t OneBitSampling; /*!< Specifies whether a single sample or three samples' majority vote is selected.
+ Selecting the single sample method increases the receiver tolerance to clock
+ deviations. This parameter can be a value of @ref SMARTCARD_OneBit_Sampling. */
+
+ uint8_t Prescaler; /*!< Specifies the SmartCard Prescaler.
+ This parameter can be any value from 0x01 to 0x1F. Prescaler value is multiplied
+ by 2 to give the division factor of the source clock frequency */
+
+ uint8_t GuardTime; /*!< Specifies the SmartCard Guard Time applied after stop bits. */
+
+ uint16_t NACKEnable; /*!< Specifies whether the SmartCard NACK transmission is enabled
+ in case of parity error.
+ This parameter can be a value of @ref SMARTCARD_NACK_Enable */
+
+ uint32_t TimeOutEnable; /*!< Specifies whether the receiver timeout is enabled.
+ This parameter can be a value of @ref SMARTCARD_Timeout_Enable*/
+
+ uint32_t TimeOutValue; /*!< Specifies the receiver time out value in number of baud blocks:
+ it is used to implement the Character Wait Time (CWT) and
+ Block Wait Time (BWT). It is coded over 24 bits. */
+
+ uint8_t BlockLength; /*!< Specifies the SmartCard Block Length in T=1 Reception mode.
+ This parameter can be any value from 0x0 to 0xFF */
+
+ uint8_t AutoRetryCount; /*!< Specifies the SmartCard auto-retry count (number of retries in
+ receive and transmit mode). When set to 0, retransmission is
+ disabled. Otherwise, its maximum value is 7 (before signalling
+ an error) */
+
+ uint32_t ClockPrescaler; /*!< Specifies the prescaler value used to divide the USART clock source.
+ This parameter can be a value of @ref SMARTCARD_ClockPrescaler. */
+
+} SMARTCARD_InitTypeDef;
+
+/**
+ * @brief SMARTCARD advanced features initalization structure definition
+ */
+typedef struct
+{
+ uint32_t AdvFeatureInit; /*!< Specifies which advanced SMARTCARD features is initialized. Several
+ advanced features may be initialized at the same time. This parameter
+ can be a value of @ref SMARTCARDEx_Advanced_Features_Initialization_Type */
+
+ uint32_t TxPinLevelInvert; /*!< Specifies whether the TX pin active level is inverted.
+ This parameter can be a value of @ref SMARTCARD_Tx_Inv */
+
+ uint32_t RxPinLevelInvert; /*!< Specifies whether the RX pin active level is inverted.
+ This parameter can be a value of @ref SMARTCARD_Rx_Inv */
+
+ uint32_t DataInvert; /*!< Specifies whether data are inverted (positive/direct logic
+ vs negative/inverted logic).
+ This parameter can be a value of @ref SMARTCARD_Data_Inv */
+
+ uint32_t Swap; /*!< Specifies whether TX and RX pins are swapped.
+ This parameter can be a value of @ref SMARTCARD_Rx_Tx_Swap */
+
+ uint32_t OverrunDisable; /*!< Specifies whether the reception overrun detection is disabled.
+ This parameter can be a value of @ref SMARTCARD_Overrun_Disable */
+
+ uint32_t DMADisableonRxError; /*!< Specifies whether the DMA is disabled in case of reception error.
+ This parameter can be a value of @ref SMARTCARD_DMA_Disable_on_Rx_Error */
+
+ uint32_t MSBFirst; /*!< Specifies whether MSB is sent first on UART line.
+ This parameter can be a value of @ref SMARTCARD_MSB_First */
+
+ uint16_t TxCompletionIndication; /*!< Specifies which transmission completion indication is used: before (when
+ relevant flag is available) or once guard time period has elapsed.
+ This parameter can be a value of @ref SMARTCARDEx_Transmission_Completion_Indication. */
+} SMARTCARD_AdvFeatureInitTypeDef;
+
+/**
+ * @brief HAL SMARTCARD State definition
+ * @note HAL SMARTCARD State value is a combination of 2 different substates: gState and RxState (see @ref SMARTCARD_State_Definition).
+ * - gState contains SMARTCARD state information related to global Handle management
+ * and also information related to Tx operations.
+ * gState value coding follow below described bitmap :
+ * b7-b6 Error information
+ * 00 : No Error
+ * 01 : (Not Used)
+ * 10 : Timeout
+ * 11 : Error
+ * b5 Peripheral initialization status
+ * 0 : Reset (Peripheral not initialized)
+ * 1 : Init done (Peripheral not initialized. HAL SMARTCARD Init function already called)
+ * b4-b3 (not used)
+ * xx : Should be set to 00
+ * b2 Intrinsic process state
+ * 0 : Ready
+ * 1 : Busy (Peripheral busy with some configuration or internal operations)
+ * b1 (not used)
+ * x : Should be set to 0
+ * b0 Tx state
+ * 0 : Ready (no Tx operation ongoing)
+ * 1 : Busy (Tx operation ongoing)
+ * - RxState contains information related to Rx operations.
+ * RxState value coding follow below described bitmap :
+ * b7-b6 (not used)
+ * xx : Should be set to 00
+ * b5 Peripheral initialization status
+ * 0 : Reset (Peripheral not initialized)
+ * 1 : Init done (Peripheral not initialized)
+ * b4-b2 (not used)
+ * xxx : Should be set to 000
+ * b1 Rx state
+ * 0 : Ready (no Rx operation ongoing)
+ * 1 : Busy (Rx operation ongoing)
+ * b0 (not used)
+ * x : Should be set to 0.
+ */
+typedef uint32_t HAL_SMARTCARD_StateTypeDef;
+
+/**
+ * @brief SMARTCARD handle Structure definition
+ */
+typedef struct __SMARTCARD_HandleTypeDef
+{
+ USART_TypeDef *Instance; /*!< USART registers base address */
+
+ SMARTCARD_InitTypeDef Init; /*!< SmartCard communication parameters */
+
+ SMARTCARD_AdvFeatureInitTypeDef AdvancedInit; /*!< SmartCard advanced features initialization parameters */
+
+ uint8_t *pTxBuffPtr; /*!< Pointer to SmartCard Tx transfer Buffer */
+
+ uint16_t TxXferSize; /*!< SmartCard Tx Transfer size */
+
+ __IO uint16_t TxXferCount; /*!< SmartCard Tx Transfer Counter */
+
+ uint8_t *pRxBuffPtr; /*!< Pointer to SmartCard Rx transfer Buffer */
+
+ uint16_t RxXferSize; /*!< SmartCard Rx Transfer size */
+
+ __IO uint16_t RxXferCount; /*!< SmartCard Rx Transfer Counter */
+
+ uint16_t NbRxDataToProcess; /*!< Number of data to process during RX ISR execution */
+
+ uint16_t NbTxDataToProcess; /*!< Number of data to process during TX ISR execution */
+
+ uint32_t FifoMode; /*!< Specifies if the FIFO mode will be used.
+ This parameter can be a value of @ref SMARTCARDEx_FIFO_mode. */
+
+ void (*RxISR)(struct __SMARTCARD_HandleTypeDef *huart); /*!< Function pointer on Rx IRQ handler */
+
+ void (*TxISR)(struct __SMARTCARD_HandleTypeDef *huart); /*!< Function pointer on Tx IRQ handler */
+
+ DMA_HandleTypeDef *hdmatx; /*!< SmartCard Tx DMA Handle parameters */
+
+ DMA_HandleTypeDef *hdmarx; /*!< SmartCard Rx DMA Handle parameters */
+
+ HAL_LockTypeDef Lock; /*!< Locking object */
+
+ __IO HAL_SMARTCARD_StateTypeDef gState; /*!< SmartCard state information related to global Handle management
+ and also related to Tx operations.
+ This parameter can be a value of @ref HAL_SMARTCARD_StateTypeDef */
+
+ __IO HAL_SMARTCARD_StateTypeDef RxState; /*!< SmartCard state information related to Rx operations.
+ This parameter can be a value of @ref HAL_SMARTCARD_StateTypeDef */
+
+ __IO uint32_t ErrorCode; /*!< SmartCard Error code */
+
+#if (USE_HAL_SMARTCARD_REGISTER_CALLBACKS == 1)
+ void (* TxCpltCallback)(struct __SMARTCARD_HandleTypeDef *hsmartcard); /*!< SMARTCARD Tx Complete Callback */
+
+ void (* RxCpltCallback)(struct __SMARTCARD_HandleTypeDef *hsmartcard); /*!< SMARTCARD Rx Complete Callback */
+
+ void (* ErrorCallback)(struct __SMARTCARD_HandleTypeDef *hsmartcard); /*!< SMARTCARD Error Callback */
+
+ void (* AbortCpltCallback)(struct __SMARTCARD_HandleTypeDef *hsmartcard); /*!< SMARTCARD Abort Complete Callback */
+
+ void (* AbortTransmitCpltCallback)(struct __SMARTCARD_HandleTypeDef *hsmartcard); /*!< SMARTCARD Abort Transmit Complete Callback */
+
+ void (* AbortReceiveCpltCallback)(struct __SMARTCARD_HandleTypeDef *hsmartcard); /*!< SMARTCARD Abort Receive Complete Callback */
+
+ void (* RxFifoFullCallback)(struct __SMARTCARD_HandleTypeDef *hsmartcard); /*!< SMARTCARD Rx Fifo Full Callback */
+
+ void (* TxFifoEmptyCallback)(struct __SMARTCARD_HandleTypeDef *hsmartcard); /*!< SMARTCARD Tx Fifo Empty Callback */
+
+ void (* MspInitCallback)(struct __SMARTCARD_HandleTypeDef *hsmartcard); /*!< SMARTCARD Msp Init callback */
+
+ void (* MspDeInitCallback)(struct __SMARTCARD_HandleTypeDef *hsmartcard); /*!< SMARTCARD Msp DeInit callback */
+#endif /* USE_HAL_SMARTCARD_REGISTER_CALLBACKS */
+
+} SMARTCARD_HandleTypeDef;
+
+#if (USE_HAL_SMARTCARD_REGISTER_CALLBACKS == 1)
+/**
+ * @brief HAL SMARTCARD Callback ID enumeration definition
+ */
+typedef enum
+{
+ HAL_SMARTCARD_TX_COMPLETE_CB_ID = 0x00U, /*!< SMARTCARD Tx Complete Callback ID */
+ HAL_SMARTCARD_RX_COMPLETE_CB_ID = 0x01U, /*!< SMARTCARD Rx Complete Callback ID */
+ HAL_SMARTCARD_ERROR_CB_ID = 0x02U, /*!< SMARTCARD Error Callback ID */
+ HAL_SMARTCARD_ABORT_COMPLETE_CB_ID = 0x03U, /*!< SMARTCARD Abort Complete Callback ID */
+ HAL_SMARTCARD_ABORT_TRANSMIT_COMPLETE_CB_ID = 0x04U, /*!< SMARTCARD Abort Transmit Complete Callback ID */
+ HAL_SMARTCARD_ABORT_RECEIVE_COMPLETE_CB_ID = 0x05U, /*!< SMARTCARD Abort Receive Complete Callback ID */
+ HAL_SMARTCARD_RX_FIFO_FULL_CB_ID = 0x06U, /*!< SMARTCARD Rx Fifo Full Callback ID */
+ HAL_SMARTCARD_TX_FIFO_EMPTY_CB_ID = 0x07U, /*!< SMARTCARD Tx Fifo Empty Callback ID */
+
+ HAL_SMARTCARD_MSPINIT_CB_ID = 0x08U, /*!< SMARTCARD MspInit callback ID */
+ HAL_SMARTCARD_MSPDEINIT_CB_ID = 0x09U /*!< SMARTCARD MspDeInit callback ID */
+
+} HAL_SMARTCARD_CallbackIDTypeDef;
+
+/**
+ * @brief HAL SMARTCARD Callback pointer definition
+ */
+typedef void (*pSMARTCARD_CallbackTypeDef)(SMARTCARD_HandleTypeDef *hsmartcard); /*!< pointer to an SMARTCARD callback function */
+
+#endif /* USE_HAL_SMARTCARD_REGISTER_CALLBACKS */
+
+/**
+ * @brief SMARTCARD clock sources
+ */
+typedef enum
+{
+ SMARTCARD_CLOCKSOURCE_D2PCLK1 = 0x00U, /*!< Domain2 PCLK1 clock source */
+ SMARTCARD_CLOCKSOURCE_D2PCLK2 = 0x01U, /*!< Domain2 PCLK2 clock source */
+ SMARTCARD_CLOCKSOURCE_HSI = 0x04U, /*!< HSI clock source */
+ SMARTCARD_CLOCKSOURCE_CSI = 0x08U, /*!< CSI clock source */
+ SMARTCARD_CLOCKSOURCE_LSE = 0x20U, /*!< LSE clock source */
+ SMARTCARD_CLOCKSOURCE_PLL2Q = 0x40U, /*!< PLL2Q clock source */
+ SMARTCARD_CLOCKSOURCE_PLL3Q = 0x80U, /*!< PLL3Q clock source */
+ SMARTCARD_CLOCKSOURCE_UNDEFINED = 0x10U /*!< undefined clock source */
+} SMARTCARD_ClockSourceTypeDef;
+
+/**
+ * @}
+ */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup SMARTCARD_Exported_Constants SMARTCARD Exported Constants
+ * @{
+ */
+
+/** @defgroup SMARTCARD_State_Definition SMARTCARD State Code Definition
+ * @{
+ */
+#define HAL_SMARTCARD_STATE_RESET 0x00000000U /*!< Peripheral is not initialized
+ Value is allowed for gState and RxState */
+#define HAL_SMARTCARD_STATE_READY 0x00000020U /*!< Peripheral Initialized and ready for use
+ Value is allowed for gState and RxState */
+#define HAL_SMARTCARD_STATE_BUSY 0x00000024U /*!< an internal process is ongoing
+ Value is allowed for gState only */
+#define HAL_SMARTCARD_STATE_BUSY_TX 0x00000021U /*!< Data Transmission process is ongoing
+ Value is allowed for gState only */
+#define HAL_SMARTCARD_STATE_BUSY_RX 0x00000022U /*!< Data Reception process is ongoing
+ Value is allowed for RxState only */
+#define HAL_SMARTCARD_STATE_BUSY_TX_RX 0x00000023U /*!< Data Transmission and Reception process is ongoing
+ Not to be used for neither gState nor RxState.
+ Value is result of combination (Or) between gState and RxState values */
+#define HAL_SMARTCARD_STATE_TIMEOUT 0x000000A0U /*!< Timeout state
+ Value is allowed for gState only */
+#define HAL_SMARTCARD_STATE_ERROR 0x000000E0U /*!< Error
+ Value is allowed for gState only */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Error_Definition SMARTCARD Error Code Definition
+ * @{
+ */
+#define HAL_SMARTCARD_ERROR_NONE ((uint32_t)0x00000000U) /*!< No error */
+#define HAL_SMARTCARD_ERROR_PE ((uint32_t)0x00000001U) /*!< Parity error */
+#define HAL_SMARTCARD_ERROR_NE ((uint32_t)0x00000002U) /*!< Noise error */
+#define HAL_SMARTCARD_ERROR_FE ((uint32_t)0x00000004U) /*!< frame error */
+#define HAL_SMARTCARD_ERROR_ORE ((uint32_t)0x00000008U) /*!< Overrun error */
+#define HAL_SMARTCARD_ERROR_DMA ((uint32_t)0x00000010U) /*!< DMA transfer error */
+#define HAL_SMARTCARD_ERROR_RTO ((uint32_t)0x00000020U) /*!< Receiver TimeOut error */
+#if (USE_HAL_SMARTCARD_REGISTER_CALLBACKS == 1)
+#define HAL_SMARTCARD_ERROR_INVALID_CALLBACK ((uint32_t)0x00000040U) /*!< Invalid Callback error */
+#endif /* USE_HAL_SMARTCARD_REGISTER_CALLBACKS */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Word_Length SMARTCARD Word Length
+ * @{
+ */
+#define SMARTCARD_WORDLENGTH_9B USART_CR1_M0 /*!< SMARTCARD frame length */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Stop_Bits SMARTCARD Number of Stop Bits
+ * @{
+ */
+#define SMARTCARD_STOPBITS_0_5 USART_CR2_STOP_0 /*!< SMARTCARD frame with 0.5 stop bit */
+#define SMARTCARD_STOPBITS_1_5 USART_CR2_STOP /*!< SMARTCARD frame with 1.5 stop bits */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Parity SMARTCARD Parity
+ * @{
+ */
+#define SMARTCARD_PARITY_EVEN USART_CR1_PCE /*!< SMARTCARD frame even parity */
+#define SMARTCARD_PARITY_ODD (USART_CR1_PCE | USART_CR1_PS) /*!< SMARTCARD frame odd parity */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Mode SMARTCARD Transfer Mode
+ * @{
+ */
+#define SMARTCARD_MODE_RX USART_CR1_RE /*!< SMARTCARD RX mode */
+#define SMARTCARD_MODE_TX USART_CR1_TE /*!< SMARTCARD TX mode */
+#define SMARTCARD_MODE_TX_RX (USART_CR1_TE |USART_CR1_RE) /*!< SMARTCARD RX and TX mode */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Clock_Polarity SMARTCARD Clock Polarity
+ * @{
+ */
+#define SMARTCARD_POLARITY_LOW 0x00000000U /*!< SMARTCARD frame low polarity */
+#define SMARTCARD_POLARITY_HIGH USART_CR2_CPOL /*!< SMARTCARD frame high polarity */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Clock_Phase SMARTCARD Clock Phase
+ * @{
+ */
+#define SMARTCARD_PHASE_1EDGE 0x00000000U /*!< SMARTCARD frame phase on first clock transition */
+#define SMARTCARD_PHASE_2EDGE USART_CR2_CPHA /*!< SMARTCARD frame phase on second clock transition */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Last_Bit SMARTCARD Last Bit
+ * @{
+ */
+#define SMARTCARD_LASTBIT_DISABLE 0x00000000U /*!< SMARTCARD frame last data bit clock pulse not output to SCLK pin */
+#define SMARTCARD_LASTBIT_ENABLE USART_CR2_LBCL /*!< SMARTCARD frame last data bit clock pulse output to SCLK pin */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_OneBit_Sampling SMARTCARD One Bit Sampling Method
+ * @{
+ */
+#define SMARTCARD_ONE_BIT_SAMPLE_DISABLE 0x00000000U /*!< SMARTCARD frame one-bit sample disabled */
+#define SMARTCARD_ONE_BIT_SAMPLE_ENABLE USART_CR3_ONEBIT /*!< SMARTCARD frame one-bit sample enabled */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_NACK_Enable SMARTCARD NACK Enable
+ * @{
+ */
+#define SMARTCARD_NACK_DISABLE 0x00000000U /*!< SMARTCARD NACK transmission disabled */
+#define SMARTCARD_NACK_ENABLE USART_CR3_NACK /*!< SMARTCARD NACK transmission enabled */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Timeout_Enable SMARTCARD Timeout Enable
+ * @{
+ */
+#define SMARTCARD_TIMEOUT_DISABLE 0x00000000U /*!< SMARTCARD receiver timeout disabled */
+#define SMARTCARD_TIMEOUT_ENABLE USART_CR2_RTOEN /*!< SMARTCARD receiver timeout enabled */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_ClockPrescaler Clock Prescaler
+ * @{
+ */
+#define SMARTCARD_PRESCALER_DIV1 0x00000000U /*!< fclk_pres = fclk */
+#define SMARTCARD_PRESCALER_DIV2 0x00000001U /*!< fclk_pres = fclk/2 */
+#define SMARTCARD_PRESCALER_DIV4 0x00000002U /*!< fclk_pres = fclk/4 */
+#define SMARTCARD_PRESCALER_DIV6 0x00000003U /*!< fclk_pres = fclk/6 */
+#define SMARTCARD_PRESCALER_DIV8 0x00000004U /*!< fclk_pres = fclk/8 */
+#define SMARTCARD_PRESCALER_DIV10 0x00000005U /*!< fclk_pres = fclk/10 */
+#define SMARTCARD_PRESCALER_DIV12 0x00000006U /*!< fclk_pres = fclk/12 */
+#define SMARTCARD_PRESCALER_DIV16 0x00000007U /*!< fclk_pres = fclk/16 */
+#define SMARTCARD_PRESCALER_DIV32 0x00000008U /*!< fclk_pres = fclk/32 */
+#define SMARTCARD_PRESCALER_DIV64 0x00000009U /*!< fclk_pres = fclk/64 */
+#define SMARTCARD_PRESCALER_DIV128 0x0000000AU /*!< fclk_pres = fclk/128 */
+#define SMARTCARD_PRESCALER_DIV256 0x0000000BU /*!< fclk_pres = fclk/256 */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Tx_Inv SMARTCARD advanced feature TX pin active level inversion
+ * @{
+ */
+#define SMARTCARD_ADVFEATURE_TXINV_DISABLE 0x00000000U /*!< TX pin active level inversion disable */
+#define SMARTCARD_ADVFEATURE_TXINV_ENABLE USART_CR2_TXINV /*!< TX pin active level inversion enable */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Rx_Inv SMARTCARD advanced feature RX pin active level inversion
+ * @{
+ */
+#define SMARTCARD_ADVFEATURE_RXINV_DISABLE 0x00000000U /*!< RX pin active level inversion disable */
+#define SMARTCARD_ADVFEATURE_RXINV_ENABLE USART_CR2_RXINV /*!< RX pin active level inversion enable */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Data_Inv SMARTCARD advanced feature Binary Data inversion
+ * @{
+ */
+#define SMARTCARD_ADVFEATURE_DATAINV_DISABLE 0x00000000U /*!< Binary data inversion disable */
+#define SMARTCARD_ADVFEATURE_DATAINV_ENABLE USART_CR2_DATAINV /*!< Binary data inversion enable */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Rx_Tx_Swap SMARTCARD advanced feature RX TX pins swap
+ * @{
+ */
+#define SMARTCARD_ADVFEATURE_SWAP_DISABLE 0x00000000U /*!< TX/RX pins swap disable */
+#define SMARTCARD_ADVFEATURE_SWAP_ENABLE USART_CR2_SWAP /*!< TX/RX pins swap enable */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Overrun_Disable SMARTCARD advanced feature Overrun Disable
+ * @{
+ */
+#define SMARTCARD_ADVFEATURE_OVERRUN_ENABLE 0x00000000U /*!< RX overrun enable */
+#define SMARTCARD_ADVFEATURE_OVERRUN_DISABLE USART_CR3_OVRDIS /*!< RX overrun disable */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_DMA_Disable_on_Rx_Error SMARTCARD advanced feature DMA Disable on Rx Error
+ * @{
+ */
+#define SMARTCARD_ADVFEATURE_DMA_ENABLEONRXERROR 0x00000000U /*!< DMA enable on Reception Error */
+#define SMARTCARD_ADVFEATURE_DMA_DISABLEONRXERROR USART_CR3_DDRE /*!< DMA disable on Reception Error */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_MSB_First SMARTCARD advanced feature MSB first
+ * @{
+ */
+#define SMARTCARD_ADVFEATURE_MSBFIRST_DISABLE 0x00000000U /*!< Most significant bit sent/received first disable */
+#define SMARTCARD_ADVFEATURE_MSBFIRST_ENABLE USART_CR2_MSBFIRST /*!< Most significant bit sent/received first enable */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Request_Parameters SMARTCARD Request Parameters
+ * @{
+ */
+#define SMARTCARD_RXDATA_FLUSH_REQUEST USART_RQR_RXFRQ /*!< Receive data flush request */
+#define SMARTCARD_TXDATA_FLUSH_REQUEST USART_RQR_TXFRQ /*!< Transmit data flush request */
+/**
+ * @}
+ */
+
+/** @defgroup SMARTCARD_Interruption_Mask SMARTCARD interruptions flags mask
+ * @{
+ */
+#define SMARTCARD_IT_MASK 0x001FU /*!< SMARTCARD interruptions flags mask */
+#define SMARTCARD_CR_MASK 0x00E0U /*!< SMARTCARD control register mask */
+#define SMARTCARD_CR_POS 5U /*!< SMARTCARD control register position */
+#define SMARTCARD_ISR_MASK 0x1F00U /*!< SMARTCARD ISR register mask */
+#define SMARTCARD_ISR_POS 8U /*!< SMARTCARD ISR register position */
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/* Exported macros -----------------------------------------------------------*/
+/** @defgroup SMARTCARD_Exported_Macros SMARTCARD Exported Macros
+ * @{
+ */
+
+/** @brief Reset SMARTCARD handle states.
+ * @param __HANDLE__ SMARTCARD handle.
+ * @retval None
+ */
+#if USE_HAL_SMARTCARD_REGISTER_CALLBACKS == 1
+#define __HAL_SMARTCARD_RESET_HANDLE_STATE(__HANDLE__) do{ \
+ (__HANDLE__)->gState = HAL_SMARTCARD_STATE_RESET; \
+ (__HANDLE__)->RxState = HAL_SMARTCARD_STATE_RESET; \
+ (__HANDLE__)->MspInitCallback = NULL; \
+ (__HANDLE__)->MspDeInitCallback = NULL; \
+ } while(0U)
+#else
+#define __HAL_SMARTCARD_RESET_HANDLE_STATE(__HANDLE__) do{ \
+ (__HANDLE__)->gState = HAL_SMARTCARD_STATE_RESET; \
+ (__HANDLE__)->RxState = HAL_SMARTCARD_STATE_RESET; \
+ } while(0U)
+#endif /*USE_HAL_SMARTCARD_REGISTER_CALLBACKS */
+
+/** @brief Flush the Smartcard Data registers.
+ * @param __HANDLE__ specifies the SMARTCARD Handle.
+ * @retval None
+ */
+#define __HAL_SMARTCARD_FLUSH_DRREGISTER(__HANDLE__) \
+ do{ \
+ SET_BIT((__HANDLE__)->Instance->RQR, SMARTCARD_RXDATA_FLUSH_REQUEST); \
+ SET_BIT((__HANDLE__)->Instance->RQR, SMARTCARD_TXDATA_FLUSH_REQUEST); \
+ } while(0U)
+
+/** @brief Clear the specified SMARTCARD pending flag.
+ * @param __HANDLE__ specifies the SMARTCARD Handle.
+ * @param __FLAG__ specifies the flag to check.
+ * This parameter can be any combination of the following values:
+ * @arg @ref SMARTCARD_CLEAR_PEF Parity error clear flag
+ * @arg @ref SMARTCARD_CLEAR_FEF Framing error clear flag
+ * @arg @ref SMARTCARD_CLEAR_NEF Noise detected clear flag
+ * @arg @ref SMARTCARD_CLEAR_OREF OverRun error clear flag
+ * @arg @ref SMARTCARD_CLEAR_IDLEF Idle line detected clear flag
+ * @arg @ref SMARTCARD_CLEAR_TCF Transmission complete clear flag
+ * @arg @ref SMARTCARD_CLEAR_TCBGTF Transmission complete before guard time clear flag
+ * @arg @ref SMARTCARD_CLEAR_RTOF Receiver timeout clear flag
+ * @arg @ref SMARTCARD_CLEAR_EOBF End of block clear flag
+ * @arg @ref SMARTCARD_CLEAR_TXFECF TXFIFO empty Clear flag
+ * @retval None
+ */
+#define __HAL_SMARTCARD_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->ICR = (__FLAG__))
+
+/** @brief Clear the SMARTCARD PE pending flag.
+ * @param __HANDLE__ specifies the SMARTCARD Handle.
+ * @retval None
+ */
+#define __HAL_SMARTCARD_CLEAR_PEFLAG(__HANDLE__) __HAL_SMARTCARD_CLEAR_FLAG((__HANDLE__), SMARTCARD_CLEAR_PEF)
+
+/** @brief Clear the SMARTCARD FE pending flag.
+ * @param __HANDLE__ specifies the SMARTCARD Handle.
+ * @retval None
+ */
+#define __HAL_SMARTCARD_CLEAR_FEFLAG(__HANDLE__) __HAL_SMARTCARD_CLEAR_FLAG((__HANDLE__), SMARTCARD_CLEAR_FEF)
+
+/** @brief Clear the SMARTCARD NE pending flag.
+ * @param __HANDLE__ specifies the SMARTCARD Handle.
+ * @retval None
+ */
+#define __HAL_SMARTCARD_CLEAR_NEFLAG(__HANDLE__) __HAL_SMARTCARD_CLEAR_FLAG((__HANDLE__), SMARTCARD_CLEAR_NEF)
+
+/** @brief Clear the SMARTCARD ORE pending flag.
+ * @param __HANDLE__ specifies the SMARTCARD Handle.
+ * @retval None
+ */
+#define __HAL_SMARTCARD_CLEAR_OREFLAG(__HANDLE__) __HAL_SMARTCARD_CLEAR_FLAG((__HANDLE__), SMARTCARD_CLEAR_OREF)
+
+/** @brief Clear the SMARTCARD IDLE pending flag.
+ * @param __HANDLE__ specifies the SMARTCARD Handle.
+ * @retval None
+ */
+#define __HAL_SMARTCARD_CLEAR_IDLEFLAG(__HANDLE__) __HAL_SMARTCARD_CLEAR_FLAG((__HANDLE__), SMARTCARD_CLEAR_IDLEF)
+
+/** @brief Check whether the specified Smartcard flag is set or not.
+ * @param __HANDLE__ specifies the SMARTCARD Handle.
+ * @param __FLAG__ specifies the flag to check.
+ * This parameter can be one of the following values:
+ * @arg @ref SMARTCARD_FLAG_TCBGT Transmission complete before guard time flag (when flag available)
+ * @arg @ref SMARTCARD_FLAG_REACK Receive enable acknowledge flag
+ * @arg @ref SMARTCARD_FLAG_TEACK Transmit enable acknowledge flag
+ * @arg @ref SMARTCARD_FLAG_BUSY Busy flag
+ * @arg @ref SMARTCARD_FLAG_EOBF End of block flag
+ * @arg @ref SMARTCARD_FLAG_RTOF Receiver timeout flag
+ * @arg @ref SMARTCARD_FLAG_TXE Transmit data register empty flag
+ * @arg @ref SMARTCARD_FLAG_TC Transmission complete flag
+ * @arg @ref SMARTCARD_FLAG_RXNE Receive data register not empty flag
+ * @arg @ref SMARTCARD_FLAG_IDLE Idle line detection flag
+ * @arg @ref SMARTCARD_FLAG_ORE Overrun error flag
+ * @arg @ref SMARTCARD_FLAG_NE Noise error flag
+ * @arg @ref SMARTCARD_FLAG_FE Framing error flag
+ * @arg @ref SMARTCARD_FLAG_PE Parity error flag
+ * @arg @ref SMARTCARD_FLAG_TXFNF TXFIFO not full flag
+ * @arg @ref SMARTCARD_FLAG_RXFNE RXFIFO not empty flag
+ * @arg @ref SMARTCARD_FLAG_TXFE TXFIFO Empty flag
+ * @arg @ref SMARTCARD_FLAG_RXFF RXFIFO Full flag
+ * @arg @ref SMARTCARD_FLAG_RXFT SMARTCARD RXFIFO threshold flag
+ * @arg @ref SMARTCARD_FLAG_TXFT SMARTCARD TXFIFO threshold flag
+ * @retval The new state of __FLAG__ (TRUE or FALSE).
+ */
+#define __HAL_SMARTCARD_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->ISR & (__FLAG__)) == (__FLAG__))
+
+/** @brief Enable the specified SmartCard interrupt.
+ * @param __HANDLE__ specifies the SMARTCARD Handle.
+ * @param __INTERRUPT__ specifies the SMARTCARD interrupt to enable.
+ * This parameter can be one of the following values:
+ * @arg @ref SMARTCARD_IT_EOB End of block interrupt
+ * @arg @ref SMARTCARD_IT_RTO Receive timeout interrupt
+ * @arg @ref SMARTCARD_IT_TXE Transmit data register empty interrupt
+ * @arg @ref SMARTCARD_IT_TC Transmission complete interrupt
+ * @arg @ref SMARTCARD_IT_TCBGT Transmission complete before guard time interrupt (when interruption available)
+ * @arg @ref SMARTCARD_IT_RXNE Receive data register not empty interrupt
+ * @arg @ref SMARTCARD_IT_IDLE Idle line detection interrupt
+ * @arg @ref SMARTCARD_IT_PE Parity error interrupt
+ * @arg @ref SMARTCARD_IT_ERR Error interrupt(frame error, noise error, overrun error)
+ * @arg @ref SMARTCARD_IT_TXFNF TX FIFO not full interruption
+ * @arg @ref SMARTCARD_IT_RXFNE RXFIFO not empty interruption
+ * @arg @ref SMARTCARD_IT_RXFF RXFIFO full interruption
+ * @arg @ref SMARTCARD_IT_TXFE TXFIFO empty interruption
+ * @arg @ref SMARTCARD_IT_RXFT RXFIFO threshold reached interruption
+ * @arg @ref SMARTCARD_IT_TXFT TXFIFO threshold reached interruption
+ * @retval None
+ */
+#define __HAL_SMARTCARD_ENABLE_IT(__HANDLE__, __INTERRUPT__) (((((__INTERRUPT__) & SMARTCARD_CR_MASK) >> SMARTCARD_CR_POS) == 1U)? ((__HANDLE__)->Instance->CR1 |= ((uint32_t)1U << ((__INTERRUPT__) & SMARTCARD_IT_MASK))): \
+ ((((__INTERRUPT__) & SMARTCARD_CR_MASK) >> SMARTCARD_CR_POS) == 2U)? ((__HANDLE__)->Instance->CR2 |= ((uint32_t)1U << ((__INTERRUPT__) & SMARTCARD_IT_MASK))): \
+ ((__HANDLE__)->Instance->CR3 |= ((uint32_t)1U << ((__INTERRUPT__) & SMARTCARD_IT_MASK))))
+
+/** @brief Disable the specified SmartCard interrupt.
+ * @param __HANDLE__ specifies the SMARTCARD Handle.
+ * @param __INTERRUPT__ specifies the SMARTCARD interrupt to disable.
+ * This parameter can be one of the following values:
+ * @arg @ref SMARTCARD_IT_EOB End of block interrupt
+ * @arg @ref SMARTCARD_IT_RTO Receive timeout interrupt
+ * @arg @ref SMARTCARD_IT_TXE Transmit data register empty interrupt
+ * @arg @ref SMARTCARD_IT_TC Transmission complete interrupt
+ * @arg @ref SMARTCARD_IT_TCBGT Transmission complete before guard time interrupt (when interruption available)
+ * @arg @ref SMARTCARD_IT_RXNE Receive data register not empty interrupt
+ * @arg @ref SMARTCARD_IT_IDLE Idle line detection interrupt
+ * @arg @ref SMARTCARD_IT_PE Parity error interrupt
+ * @arg @ref SMARTCARD_IT_ERR Error interrupt(frame error, noise error, overrun error)
+ * @arg @ref SMARTCARD_IT_TXFNF TX FIFO not full interruption
+ * @arg @ref SMARTCARD_IT_RXFNE RXFIFO not empty interruption
+ * @arg @ref SMARTCARD_IT_RXFF RXFIFO full interruption
+ * @arg @ref SMARTCARD_IT_TXFE TXFIFO empty interruption
+ * @arg @ref SMARTCARD_IT_RXFT RXFIFO threshold reached interruption
+ * @arg @ref SMARTCARD_IT_TXFT TXFIFO threshold reached interruption
+ * @retval None
+ */
+#define __HAL_SMARTCARD_DISABLE_IT(__HANDLE__, __INTERRUPT__) (((((__INTERRUPT__) & SMARTCARD_CR_MASK) >> SMARTCARD_CR_POS) == 1U)? ((__HANDLE__)->Instance->CR1 &= ~ ((uint32_t)1U << ((__INTERRUPT__) & SMARTCARD_IT_MASK))): \
+ ((((__INTERRUPT__) & SMARTCARD_CR_MASK) >> SMARTCARD_CR_POS) == 2U)? ((__HANDLE__)->Instance->CR2 &= ~ ((uint32_t)1U << ((__INTERRUPT__) & SMARTCARD_IT_MASK))): \
+ ((__HANDLE__)->Instance->CR3 &= ~ ((uint32_t)1U << ((__INTERRUPT__) & SMARTCARD_IT_MASK))))
+
+/** @brief Check whether the specified SmartCard interrupt has occurred or not.
+ * @param __HANDLE__ specifies the SMARTCARD Handle.
+ * @param __INTERRUPT__ specifies the SMARTCARD interrupt to check.
+ * This parameter can be one of the following values:
+ * @arg @ref SMARTCARD_IT_EOB End of block interrupt
+ * @arg @ref SMARTCARD_IT_RTO Receive timeout interrupt
+ * @arg @ref SMARTCARD_IT_TXE Transmit data register empty interrupt
+ * @arg @ref SMARTCARD_IT_TC Transmission complete interrupt
+ * @arg @ref SMARTCARD_IT_TCBGT Transmission complete before guard time interrupt (when interruption available)
+ * @arg @ref SMARTCARD_IT_RXNE Receive data register not empty interrupt
+ * @arg @ref SMARTCARD_IT_IDLE Idle line detection interrupt
+ * @arg @ref SMARTCARD_IT_PE Parity error interrupt
+ * @arg @ref SMARTCARD_IT_ERR Error interrupt(frame error, noise error, overrun error)
+ * @arg @ref SMARTCARD_IT_TXFNF TX FIFO not full interruption
+ * @arg @ref SMARTCARD_IT_RXFNE RXFIFO not empty interruption
+ * @arg @ref SMARTCARD_IT_RXFF RXFIFO full interruption
+ * @arg @ref SMARTCARD_IT_TXFE TXFIFO empty interruption
+ * @arg @ref SMARTCARD_IT_RXFT RXFIFO threshold reached interruption
+ * @arg @ref SMARTCARD_IT_TXFT TXFIFO threshold reached interruption
+ * @retval The new state of __INTERRUPT__ (SET or RESET).
+ */
+#define __HAL_SMARTCARD_GET_IT(__HANDLE__, __INTERRUPT__) ((((__HANDLE__)->Instance->ISR & ((uint32_t)0x01U << (((__INTERRUPT__) & SMARTCARD_ISR_MASK)>> SMARTCARD_ISR_POS))) != 0U) ? SET : RESET)
+
+/** @brief Check whether the specified SmartCard interrupt source is enabled or not.
+ * @param __HANDLE__ specifies the SMARTCARD Handle.
+ * @param __INTERRUPT__ specifies the SMARTCARD interrupt source to check.
+ * This parameter can be one of the following values:
+ * @arg @ref SMARTCARD_IT_EOB End of block interrupt
+ * @arg @ref SMARTCARD_IT_RTO Receive timeout interrupt
+ * @arg @ref SMARTCARD_IT_TXE Transmit data register empty interrupt
+ * @arg @ref SMARTCARD_IT_TC Transmission complete interrupt
+ * @arg @ref SMARTCARD_IT_TCBGT Transmission complete before guard time interrupt (when interruption available)
+ * @arg @ref SMARTCARD_IT_RXNE Receive data register not empty interrupt
+ * @arg @ref SMARTCARD_IT_IDLE Idle line detection interrupt
+ * @arg @ref SMARTCARD_IT_PE Parity error interrupt
+ * @arg @ref SMARTCARD_IT_ERR Error interrupt(frame error, noise error, overrun error)
+ * @arg @ref SMARTCARD_IT_TXFNF TX FIFO not full interruption
+ * @arg @ref SMARTCARD_IT_RXFNE RXFIFO not empty interruption
+ * @arg @ref SMARTCARD_IT_RXFF RXFIFO full interruption
+ * @arg @ref SMARTCARD_IT_TXFE TXFIFO empty interruption
+ * @arg @ref SMARTCARD_IT_RXFT RXFIFO threshold reached interruption
+ * @arg @ref SMARTCARD_IT_TXFT TXFIFO threshold reached interruption
+ * @retval The new state of __INTERRUPT__ (SET or RESET).
+ */
+#define __HAL_SMARTCARD_GET_IT_SOURCE(__HANDLE__, __INTERRUPT__) ((((((((__INTERRUPT__) & SMARTCARD_CR_MASK) >> SMARTCARD_CR_POS) == 0x01U)? (__HANDLE__)->Instance->CR1 : \
+ (((((__INTERRUPT__) & SMARTCARD_CR_MASK) >> SMARTCARD_CR_POS) == 0x02U)? (__HANDLE__)->Instance->CR2 : \
+ (__HANDLE__)->Instance->CR3)) & ((uint32_t)0x01U << (((uint16_t)(__INTERRUPT__)) & SMARTCARD_IT_MASK))) != 0U) ? SET : RESET)
+
+/** @brief Clear the specified SMARTCARD ISR flag, in setting the proper ICR register flag.
+ * @param __HANDLE__ specifies the SMARTCARD Handle.
+ * @param __IT_CLEAR__ specifies the interrupt clear register flag that needs to be set
+ * to clear the corresponding interrupt.
+ * This parameter can be one of the following values:
+ * @arg @ref SMARTCARD_CLEAR_PEF Parity error clear flag
+ * @arg @ref SMARTCARD_CLEAR_FEF Framing error clear flag
+ * @arg @ref SMARTCARD_CLEAR_NEF Noise detected clear flag
+ * @arg @ref SMARTCARD_CLEAR_OREF OverRun error clear flag
+ * @arg @ref SMARTCARD_CLEAR_IDLEF Idle line detection clear flag
+ * @arg @ref SMARTCARD_CLEAR_TXFECF TXFIFO empty Clear Flag
+ * @arg @ref SMARTCARD_CLEAR_TCF Transmission complete clear flag
+ * @arg @ref SMARTCARD_CLEAR_TCBGTF Transmission complete before guard time clear flag (when flag available)
+ * @arg @ref SMARTCARD_CLEAR_RTOF Receiver timeout clear flag
+ * @arg @ref SMARTCARD_CLEAR_EOBF End of block clear flag
+ * @retval None
+ */
+#define __HAL_SMARTCARD_CLEAR_IT(__HANDLE__, __IT_CLEAR__) ((__HANDLE__)->Instance->ICR |= (uint32_t)(__IT_CLEAR__))
+
+/** @brief Set a specific SMARTCARD request flag.
+ * @param __HANDLE__ specifies the SMARTCARD Handle.
+ * @param __REQ__ specifies the request flag to set
+ * This parameter can be one of the following values:
+ * @arg @ref SMARTCARD_RXDATA_FLUSH_REQUEST Receive data flush Request
+ * @arg @ref SMARTCARD_TXDATA_FLUSH_REQUEST Transmit data flush Request
+ * @retval None
+ */
+#define __HAL_SMARTCARD_SEND_REQ(__HANDLE__, __REQ__) ((__HANDLE__)->Instance->RQR |= (uint16_t)(__REQ__))
+
+/** @brief Enable the SMARTCARD one bit sample method.
+ * @param __HANDLE__ specifies the SMARTCARD Handle.
+ * @retval None
+ */
+#define __HAL_SMARTCARD_ONE_BIT_SAMPLE_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3|= USART_CR3_ONEBIT)
+
+/** @brief Disable the SMARTCARD one bit sample method.
+ * @param __HANDLE__ specifies the SMARTCARD Handle.
+ * @retval None
+ */
+#define __HAL_SMARTCARD_ONE_BIT_SAMPLE_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3 &= (uint32_t)~((uint32_t)USART_CR3_ONEBIT))
+
+/** @brief Enable the USART associated to the SMARTCARD Handle.
+ * @param __HANDLE__ specifies the SMARTCARD Handle.
+ * @retval None
+ */
+#define __HAL_SMARTCARD_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 |= USART_CR1_UE)
+
+/** @brief Disable the USART associated to the SMARTCARD Handle
+ * @param __HANDLE__ specifies the SMARTCARD Handle.
+ * @retval None
+ */
+#define __HAL_SMARTCARD_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 &= ~USART_CR1_UE)
+
+/**
+ * @}
+ */
+
+/* Private macros -------------------------------------------------------------*/
+/** @defgroup SMARTCARD_Private_Macros SMARTCARD Private Macros
+ * @{
+ */
+
+/** @brief Report the SMARTCARD clock source.
+ * @param __HANDLE__ specifies the SMARTCARD Handle.
+ * @param __CLOCKSOURCE__ output variable.
+ * @retval the SMARTCARD clocking source, written in __CLOCKSOURCE__.
+ */
+#define SMARTCARD_GETCLOCKSOURCE(__HANDLE__,__CLOCKSOURCE__) \
+ do { \
+ if ((__HANDLE__)->Instance == USART1) \
+ { \
+ switch (__HAL_RCC_GET_USART1_SOURCE()) \
+ { \
+ case RCC_USART1CLKSOURCE_D2PCLK2: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_D2PCLK2; \
+ break; \
+ case RCC_USART1CLKSOURCE_PLL2: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_PLL2Q; \
+ break; \
+ case RCC_USART1CLKSOURCE_PLL3: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_PLL3Q; \
+ break; \
+ case RCC_USART1CLKSOURCE_HSI: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_HSI; \
+ break; \
+ case RCC_USART1CLKSOURCE_CSI: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_CSI; \
+ break; \
+ case RCC_USART1CLKSOURCE_LSE: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_LSE; \
+ break; \
+ default: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_UNDEFINED; \
+ break; \
+ } \
+ } \
+ else if ((__HANDLE__)->Instance == USART2) \
+ { \
+ switch (__HAL_RCC_GET_USART2_SOURCE()) \
+ { \
+ case RCC_USART2CLKSOURCE_D2PCLK1: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_D2PCLK1; \
+ break; \
+ case RCC_USART2CLKSOURCE_PLL2: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_PLL2Q; \
+ break; \
+ case RCC_USART2CLKSOURCE_PLL3: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_PLL3Q; \
+ break; \
+ case RCC_USART2CLKSOURCE_HSI: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_HSI; \
+ break; \
+ case RCC_USART2CLKSOURCE_CSI: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_CSI; \
+ break; \
+ case RCC_USART2CLKSOURCE_LSE: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_LSE; \
+ break; \
+ default: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_UNDEFINED; \
+ break; \
+ } \
+ } \
+ else if ((__HANDLE__)->Instance == USART3) \
+ { \
+ switch (__HAL_RCC_GET_USART3_SOURCE()) \
+ { \
+ case RCC_USART3CLKSOURCE_D2PCLK1: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_D2PCLK1; \
+ break; \
+ case RCC_USART3CLKSOURCE_PLL2: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_PLL2Q; \
+ break; \
+ case RCC_USART3CLKSOURCE_PLL3: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_PLL3Q; \
+ break; \
+ case RCC_USART3CLKSOURCE_HSI: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_HSI; \
+ break; \
+ case RCC_USART3CLKSOURCE_CSI: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_CSI; \
+ break; \
+ case RCC_USART3CLKSOURCE_LSE: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_LSE; \
+ break; \
+ default: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_UNDEFINED; \
+ break; \
+ } \
+ } \
+ else if ((__HANDLE__)->Instance == USART6) \
+ { \
+ switch (__HAL_RCC_GET_USART6_SOURCE()) \
+ { \
+ case RCC_USART6CLKSOURCE_D2PCLK2: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_D2PCLK2; \
+ break; \
+ case RCC_USART6CLKSOURCE_PLL2: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_PLL2Q; \
+ break; \
+ case RCC_USART6CLKSOURCE_PLL3: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_PLL3Q; \
+ break; \
+ case RCC_USART6CLKSOURCE_HSI: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_HSI; \
+ break; \
+ case RCC_USART6CLKSOURCE_CSI: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_CSI; \
+ break; \
+ case RCC_USART6CLKSOURCE_LSE: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_LSE; \
+ break; \
+ default: \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_UNDEFINED; \
+ break; \
+ } \
+ } \
+ else \
+ { \
+ (__CLOCKSOURCE__) = SMARTCARD_CLOCKSOURCE_UNDEFINED; \
+ } \
+ } while(0U)
+
+/** @brief Check the Baud rate range.
+ * @note The maximum Baud Rate is derived from the maximum clock on H7 (100 MHz)
+ * divided by the oversampling used on the SMARTCARD (i.e. 16).
+ * @param __BAUDRATE__ Baud rate set by the configuration function.
+ * @retval Test result (TRUE or FALSE)
+ */
+#define IS_SMARTCARD_BAUDRATE(__BAUDRATE__) ((__BAUDRATE__) < 6250001U)
+
+/** @brief Check the block length range.
+ * @note The maximum SMARTCARD block length is 0xFF.
+ * @param __LENGTH__ block length.
+ * @retval Test result (TRUE or FALSE)
+ */
+#define IS_SMARTCARD_BLOCKLENGTH(__LENGTH__) ((__LENGTH__) <= 0xFFU)
+
+/** @brief Check the receiver timeout value.
+ * @note The maximum SMARTCARD receiver timeout value is 0xFFFFFF.
+ * @param __TIMEOUTVALUE__ receiver timeout value.
+ * @retval Test result (TRUE or FALSE)
+ */
+#define IS_SMARTCARD_TIMEOUT_VALUE(__TIMEOUTVALUE__) ((__TIMEOUTVALUE__) <= 0xFFFFFFU)
+
+/** @brief Check the SMARTCARD autoretry counter value.
+ * @note The maximum number of retransmissions is 0x7.
+ * @param __COUNT__ number of retransmissions.
+ * @retval Test result (TRUE or FALSE)
+ */
+#define IS_SMARTCARD_AUTORETRY_COUNT(__COUNT__) ((__COUNT__) <= 0x7U)
+
+/** @brief Ensure that SMARTCARD frame length is valid.
+ * @param __LENGTH__ SMARTCARD frame length.
+ * @retval SET (__LENGTH__ is valid) or RESET (__LENGTH__ is invalid)
+ */
+#define IS_SMARTCARD_WORD_LENGTH(__LENGTH__) ((__LENGTH__) == SMARTCARD_WORDLENGTH_9B)
+
+/** @brief Ensure that SMARTCARD frame number of stop bits is valid.
+ * @param __STOPBITS__ SMARTCARD frame number of stop bits.
+ * @retval SET (__STOPBITS__ is valid) or RESET (__STOPBITS__ is invalid)
+ */
+#define IS_SMARTCARD_STOPBITS(__STOPBITS__) (((__STOPBITS__) == SMARTCARD_STOPBITS_0_5) ||\
+ ((__STOPBITS__) == SMARTCARD_STOPBITS_1_5))
+
+/** @brief Ensure that SMARTCARD frame parity is valid.
+ * @param __PARITY__ SMARTCARD frame parity.
+ * @retval SET (__PARITY__ is valid) or RESET (__PARITY__ is invalid)
+ */
+#define IS_SMARTCARD_PARITY(__PARITY__) (((__PARITY__) == SMARTCARD_PARITY_EVEN) || \
+ ((__PARITY__) == SMARTCARD_PARITY_ODD))
+
+/** @brief Ensure that SMARTCARD communication mode is valid.
+ * @param __MODE__ SMARTCARD communication mode.
+ * @retval SET (__MODE__ is valid) or RESET (__MODE__ is invalid)
+ */
+#define IS_SMARTCARD_MODE(__MODE__) ((((__MODE__) & 0xFFF3U) == 0x00U) && ((__MODE__) != 0x00U))
+
+/** @brief Ensure that SMARTCARD frame polarity is valid.
+ * @param __CPOL__ SMARTCARD frame polarity.
+ * @retval SET (__CPOL__ is valid) or RESET (__CPOL__ is invalid)
+ */
+#define IS_SMARTCARD_POLARITY(__CPOL__) (((__CPOL__) == SMARTCARD_POLARITY_LOW) || ((__CPOL__) == SMARTCARD_POLARITY_HIGH))
+
+/** @brief Ensure that SMARTCARD frame phase is valid.
+ * @param __CPHA__ SMARTCARD frame phase.
+ * @retval SET (__CPHA__ is valid) or RESET (__CPHA__ is invalid)
+ */
+#define IS_SMARTCARD_PHASE(__CPHA__) (((__CPHA__) == SMARTCARD_PHASE_1EDGE) || ((__CPHA__) == SMARTCARD_PHASE_2EDGE))
+
+/** @brief Ensure that SMARTCARD frame last bit clock pulse setting is valid.
+ * @param __LASTBIT__ SMARTCARD frame last bit clock pulse setting.
+ * @retval SET (__LASTBIT__ is valid) or RESET (__LASTBIT__ is invalid)
+ */
+#define IS_SMARTCARD_LASTBIT(__LASTBIT__) (((__LASTBIT__) == SMARTCARD_LASTBIT_DISABLE) || \
+ ((__LASTBIT__) == SMARTCARD_LASTBIT_ENABLE))
+
+/** @brief Ensure that SMARTCARD frame sampling is valid.
+ * @param __ONEBIT__ SMARTCARD frame sampling.
+ * @retval SET (__ONEBIT__ is valid) or RESET (__ONEBIT__ is invalid)
+ */
+#define IS_SMARTCARD_ONE_BIT_SAMPLE(__ONEBIT__) (((__ONEBIT__) == SMARTCARD_ONE_BIT_SAMPLE_DISABLE) || \
+ ((__ONEBIT__) == SMARTCARD_ONE_BIT_SAMPLE_ENABLE))
+
+/** @brief Ensure that SMARTCARD NACK transmission setting is valid.
+ * @param __NACK__ SMARTCARD NACK transmission setting.
+ * @retval SET (__NACK__ is valid) or RESET (__NACK__ is invalid)
+ */
+#define IS_SMARTCARD_NACK(__NACK__) (((__NACK__) == SMARTCARD_NACK_ENABLE) || \
+ ((__NACK__) == SMARTCARD_NACK_DISABLE))
+
+/** @brief Ensure that SMARTCARD receiver timeout setting is valid.
+ * @param __TIMEOUT__ SMARTCARD receiver timeout setting.
+ * @retval SET (__TIMEOUT__ is valid) or RESET (__TIMEOUT__ is invalid)
+ */
+#define IS_SMARTCARD_TIMEOUT(__TIMEOUT__) (((__TIMEOUT__) == SMARTCARD_TIMEOUT_DISABLE) || \
+ ((__TIMEOUT__) == SMARTCARD_TIMEOUT_ENABLE))
+
+/** @brief Ensure that SMARTCARD clock Prescaler is valid.
+ * @param __CLOCKPRESCALER__ SMARTCARD clock Prescaler value.
+ * @retval SET (__CLOCKPRESCALER__ is valid) or RESET (__CLOCKPRESCALER__ is invalid)
+ */
+#define IS_SMARTCARD_CLOCKPRESCALER(__CLOCKPRESCALER__) (((__CLOCKPRESCALER__) == SMARTCARD_PRESCALER_DIV1) || \
+ ((__CLOCKPRESCALER__) == SMARTCARD_PRESCALER_DIV2) || \
+ ((__CLOCKPRESCALER__) == SMARTCARD_PRESCALER_DIV4) || \
+ ((__CLOCKPRESCALER__) == SMARTCARD_PRESCALER_DIV6) || \
+ ((__CLOCKPRESCALER__) == SMARTCARD_PRESCALER_DIV8) || \
+ ((__CLOCKPRESCALER__) == SMARTCARD_PRESCALER_DIV10) || \
+ ((__CLOCKPRESCALER__) == SMARTCARD_PRESCALER_DIV12) || \
+ ((__CLOCKPRESCALER__) == SMARTCARD_PRESCALER_DIV16) || \
+ ((__CLOCKPRESCALER__) == SMARTCARD_PRESCALER_DIV32) || \
+ ((__CLOCKPRESCALER__) == SMARTCARD_PRESCALER_DIV64) || \
+ ((__CLOCKPRESCALER__) == SMARTCARD_PRESCALER_DIV128) || \
+ ((__CLOCKPRESCALER__) == SMARTCARD_PRESCALER_DIV256))
+
+/** @brief Ensure that SMARTCARD advanced features initialization is valid.
+ * @param __INIT__ SMARTCARD advanced features initialization.
+ * @retval SET (__INIT__ is valid) or RESET (__INIT__ is invalid)
+ */
+#define IS_SMARTCARD_ADVFEATURE_INIT(__INIT__) ((__INIT__) <= (SMARTCARD_ADVFEATURE_NO_INIT | \
+ SMARTCARD_ADVFEATURE_TXINVERT_INIT | \
+ SMARTCARD_ADVFEATURE_RXINVERT_INIT | \
+ SMARTCARD_ADVFEATURE_DATAINVERT_INIT | \
+ SMARTCARD_ADVFEATURE_SWAP_INIT | \
+ SMARTCARD_ADVFEATURE_RXOVERRUNDISABLE_INIT | \
+ SMARTCARD_ADVFEATURE_DMADISABLEONERROR_INIT | \
+ SMARTCARD_ADVFEATURE_MSBFIRST_INIT))
+
+/** @brief Ensure that SMARTCARD frame TX inversion setting is valid.
+ * @param __TXINV__ SMARTCARD frame TX inversion setting.
+ * @retval SET (__TXINV__ is valid) or RESET (__TXINV__ is invalid)
+ */
+#define IS_SMARTCARD_ADVFEATURE_TXINV(__TXINV__) (((__TXINV__) == SMARTCARD_ADVFEATURE_TXINV_DISABLE) || \
+ ((__TXINV__) == SMARTCARD_ADVFEATURE_TXINV_ENABLE))
+
+/** @brief Ensure that SMARTCARD frame RX inversion setting is valid.
+ * @param __RXINV__ SMARTCARD frame RX inversion setting.
+ * @retval SET (__RXINV__ is valid) or RESET (__RXINV__ is invalid)
+ */
+#define IS_SMARTCARD_ADVFEATURE_RXINV(__RXINV__) (((__RXINV__) == SMARTCARD_ADVFEATURE_RXINV_DISABLE) || \
+ ((__RXINV__) == SMARTCARD_ADVFEATURE_RXINV_ENABLE))
+
+/** @brief Ensure that SMARTCARD frame data inversion setting is valid.
+ * @param __DATAINV__ SMARTCARD frame data inversion setting.
+ * @retval SET (__DATAINV__ is valid) or RESET (__DATAINV__ is invalid)
+ */
+#define IS_SMARTCARD_ADVFEATURE_DATAINV(__DATAINV__) (((__DATAINV__) == SMARTCARD_ADVFEATURE_DATAINV_DISABLE) || \
+ ((__DATAINV__) == SMARTCARD_ADVFEATURE_DATAINV_ENABLE))
+
+/** @brief Ensure that SMARTCARD frame RX/TX pins swap setting is valid.
+ * @param __SWAP__ SMARTCARD frame RX/TX pins swap setting.
+ * @retval SET (__SWAP__ is valid) or RESET (__SWAP__ is invalid)
+ */
+#define IS_SMARTCARD_ADVFEATURE_SWAP(__SWAP__) (((__SWAP__) == SMARTCARD_ADVFEATURE_SWAP_DISABLE) || \
+ ((__SWAP__) == SMARTCARD_ADVFEATURE_SWAP_ENABLE))
+
+/** @brief Ensure that SMARTCARD frame overrun setting is valid.
+ * @param __OVERRUN__ SMARTCARD frame overrun setting.
+ * @retval SET (__OVERRUN__ is valid) or RESET (__OVERRUN__ is invalid)
+ */
+#define IS_SMARTCARD_OVERRUN(__OVERRUN__) (((__OVERRUN__) == SMARTCARD_ADVFEATURE_OVERRUN_ENABLE) || \
+ ((__OVERRUN__) == SMARTCARD_ADVFEATURE_OVERRUN_DISABLE))
+
+/** @brief Ensure that SMARTCARD DMA enabling or disabling on error setting is valid.
+ * @param __DMA__ SMARTCARD DMA enabling or disabling on error setting.
+ * @retval SET (__DMA__ is valid) or RESET (__DMA__ is invalid)
+ */
+#define IS_SMARTCARD_ADVFEATURE_DMAONRXERROR(__DMA__) (((__DMA__) == SMARTCARD_ADVFEATURE_DMA_ENABLEONRXERROR) || \
+ ((__DMA__) == SMARTCARD_ADVFEATURE_DMA_DISABLEONRXERROR))
+
+/** @brief Ensure that SMARTCARD frame MSB first setting is valid.
+ * @param __MSBFIRST__ SMARTCARD frame MSB first setting.
+ * @retval SET (__MSBFIRST__ is valid) or RESET (__MSBFIRST__ is invalid)
+ */
+#define IS_SMARTCARD_ADVFEATURE_MSBFIRST(__MSBFIRST__) (((__MSBFIRST__) == SMARTCARD_ADVFEATURE_MSBFIRST_DISABLE) || \
+ ((__MSBFIRST__) == SMARTCARD_ADVFEATURE_MSBFIRST_ENABLE))
+
+/** @brief Ensure that SMARTCARD request parameter is valid.
+ * @param __PARAM__ SMARTCARD request parameter.
+ * @retval SET (__PARAM__ is valid) or RESET (__PARAM__ is invalid)
+ */
+#define IS_SMARTCARD_REQUEST_PARAMETER(__PARAM__) (((__PARAM__) == SMARTCARD_RXDATA_FLUSH_REQUEST) || \
+ ((__PARAM__) == SMARTCARD_TXDATA_FLUSH_REQUEST))
+
+/**
+ * @}
+ */
+
+/* Include SMARTCARD HAL Extended module */
+#include "stm32h7xx_hal_smartcard_ex.h"
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup SMARTCARD_Exported_Functions
+ * @{
+ */
+
+/* Initialization and de-initialization functions ****************************/
+/** @addtogroup SMARTCARD_Exported_Functions_Group1
+ * @{
+ */
+
+HAL_StatusTypeDef HAL_SMARTCARD_Init(SMARTCARD_HandleTypeDef *hsmartcard);
+HAL_StatusTypeDef HAL_SMARTCARD_DeInit(SMARTCARD_HandleTypeDef *hsmartcard);
+void HAL_SMARTCARD_MspInit(SMARTCARD_HandleTypeDef *hsmartcard);
+void HAL_SMARTCARD_MspDeInit(SMARTCARD_HandleTypeDef *hsmartcard);
+
+#if (USE_HAL_SMARTCARD_REGISTER_CALLBACKS == 1)
+/* Callbacks Register/UnRegister functions ***********************************/
+HAL_StatusTypeDef HAL_SMARTCARD_RegisterCallback(SMARTCARD_HandleTypeDef *hsmartcard, HAL_SMARTCARD_CallbackIDTypeDef CallbackID, pSMARTCARD_CallbackTypeDef pCallback);
+HAL_StatusTypeDef HAL_SMARTCARD_UnRegisterCallback(SMARTCARD_HandleTypeDef *hsmartcard, HAL_SMARTCARD_CallbackIDTypeDef CallbackID);
+#endif /* USE_HAL_SMARTCARD_REGISTER_CALLBACKS */
+
+/**
+ * @}
+ */
+
+/* IO operation functions *****************************************************/
+/** @addtogroup SMARTCARD_Exported_Functions_Group2
+ * @{
+ */
+
+HAL_StatusTypeDef HAL_SMARTCARD_Transmit(SMARTCARD_HandleTypeDef *hsmartcard, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_SMARTCARD_Receive(SMARTCARD_HandleTypeDef *hsmartcard, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_SMARTCARD_Transmit_IT(SMARTCARD_HandleTypeDef *hsmartcard, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_SMARTCARD_Receive_IT(SMARTCARD_HandleTypeDef *hsmartcard, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_SMARTCARD_Transmit_DMA(SMARTCARD_HandleTypeDef *hsmartcard, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_SMARTCARD_Receive_DMA(SMARTCARD_HandleTypeDef *hsmartcard, uint8_t *pData, uint16_t Size);
+/* Transfer Abort functions */
+HAL_StatusTypeDef HAL_SMARTCARD_Abort(SMARTCARD_HandleTypeDef *hsmartcard);
+HAL_StatusTypeDef HAL_SMARTCARD_AbortTransmit(SMARTCARD_HandleTypeDef *hsmartcard);
+HAL_StatusTypeDef HAL_SMARTCARD_AbortReceive(SMARTCARD_HandleTypeDef *hsmartcard);
+HAL_StatusTypeDef HAL_SMARTCARD_Abort_IT(SMARTCARD_HandleTypeDef *hsmartcard);
+HAL_StatusTypeDef HAL_SMARTCARD_AbortTransmit_IT(SMARTCARD_HandleTypeDef *hsmartcard);
+HAL_StatusTypeDef HAL_SMARTCARD_AbortReceive_IT(SMARTCARD_HandleTypeDef *hsmartcard);
+
+void HAL_SMARTCARD_IRQHandler(SMARTCARD_HandleTypeDef *hsmartcard);
+void HAL_SMARTCARD_TxCpltCallback(SMARTCARD_HandleTypeDef *hsmartcard);
+void HAL_SMARTCARD_RxCpltCallback(SMARTCARD_HandleTypeDef *hsmartcard);
+void HAL_SMARTCARD_ErrorCallback(SMARTCARD_HandleTypeDef *hsmartcard);
+void HAL_SMARTCARD_AbortCpltCallback(SMARTCARD_HandleTypeDef *hsmartcard);
+void HAL_SMARTCARD_AbortTransmitCpltCallback(SMARTCARD_HandleTypeDef *hsmartcard);
+void HAL_SMARTCARD_AbortReceiveCpltCallback(SMARTCARD_HandleTypeDef *hsmartcard);
+
+/**
+ * @}
+ */
+
+/* Peripheral State and Error functions ***************************************/
+/** @addtogroup SMARTCARD_Exported_Functions_Group4
+ * @{
+ */
+
+HAL_SMARTCARD_StateTypeDef HAL_SMARTCARD_GetState(SMARTCARD_HandleTypeDef *hsmartcard);
+uint32_t HAL_SMARTCARD_GetError(SMARTCARD_HandleTypeDef *hsmartcard);
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* STM32H7xx_HAL_SMARTCARD_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
