mbed official
mbed library sources. Supersedes mbed-src.
Dependents: Nucleo_Hello_Encoder BLE_iBeaconScan AM1805_DEMO DISCO-F429ZI_ExportTemplate1 ... more
Diff: targets/TARGET_STM/TARGET_STM32H7/device/stm32h7xx_hal_rtc.c
- Revision:
- 189:f392fc9709a3
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/TARGET_STM/TARGET_STM32H7/device/stm32h7xx_hal_rtc.c Wed Feb 20 22:31:08 2019 +0000
@@ -0,0 +1,1845 @@
+/**
+ ******************************************************************************
+ * @file stm32h7xx_hal_rtc.c
+ * @author MCD Application Team
+ * @brief RTC HAL module driver.
+ * This file provides firmware functions to manage the following
+ * functionalities of the Real-Time Clock (RTC) peripheral:
+ * + Initialization/de-initialization
+ * + Calendar (Time and Date) configuration
+ * + Alarms (Alarm A and Alarm B) configuration
+ * + WakeUp Timer configuration
+ * + TimeStamp configuration
+ * + Tampers configuration
+ * + Backup Data Registers configuration
+ * + RTC Tamper and TimeStamp Pins Selection
+ * + Interrupts and flags management
+ *
+ @verbatim
+ ===============================================================================
+ ##### RTC Operating Condition #####
+ ===============================================================================
+ [..] The real-time clock (RTC) and the RTC backup registers can be powered
+ from the VBAT voltage when the main VDD supply is powered off.
+ To retain the content of the RTC backup registers and supply the RTC
+ when VDD is turned off, VBAT pin can be connected to an optional
+ standby voltage supplied by a battery or by another source.
+
+ ##### Backup Domain Reset #####
+ ===============================================================================
+ [..] The backup domain reset sets all RTC registers and the RCC_BDCR register
+ to their reset values.
+ A backup domain reset is generated when one of the following events occurs:
+ (#) Software reset, triggered by setting the BDRST bit in the
+ RCC Backup domain control register (RCC_BDCR).
+ (#) VDD or VBAT power on, if both supplies have previously been powered off.
+ (#) Tamper detection event resets all data backup registers.
+
+ ##### Backup Domain Access #####
+ ===================================================================
+ [..] After reset, the backup domain (RTC registers, RTC backup data
+ registers and backup SRAM) is protected against possible unwanted write
+ accesses.
+
+ [..] To enable access to the RTC Domain and RTC registers, proceed as follows:
+ (#) Call the function HAL_RCCEx_PeriphCLKConfig with RCC_PERIPHCLK_RTC for
+ PeriphClockSelection and select RTCClockSelection (LSE, LSI or HSEdiv32)
+ (#) Enable RTC Clock using the __HAL_RCC_RTC_ENABLE() macro.
+
+ ##### How to use RTC Driver #####
+ ===================================================================
+ [..]
+ (#) Enable the RTC domain access (see description in the section above).
+ (#) Configure the RTC Prescaler (Asynchronous and Synchronous) and RTC hour
+ format using the HAL_RTC_Init() function.
+
+ *** Time and Date configuration ***
+ ===================================
+ [..]
+ (#) To configure the RTC Calendar (Time and Date) use the HAL_RTC_SetTime()
+ and HAL_RTC_SetDate() functions.
+ (#) To read the RTC Calendar, use the HAL_RTC_GetTime() and HAL_RTC_GetDate() functions.
+
+ *** Alarm configuration ***
+ ===========================
+ [..]
+ (#) To configure the RTC Alarm use the HAL_RTC_SetAlarm() function.
+ You can also configure the RTC Alarm with interrupt mode using the
+ HAL_RTC_SetAlarm_IT() function.
+ (#) To read the RTC Alarm, use the HAL_RTC_GetAlarm() function.
+
+ ##### RTC and low power modes #####
+ ===================================================================
+ [..] The MCU can be woken up from a low power mode by an RTC alternate
+ function.
+ [..] The RTC alternate functions are the RTC alarms (Alarm A and Alarm B),
+ RTC wakeup, RTC tamper event detection and RTC time stamp event detection.
+ These RTC alternate functions can wake up the system from the Stop and Standby low power
+ modes.
+ [..] The system can also wake up from low power modes without depending
+ on an external interrupt (Auto-wakeup mode), by using the RTC alarm
+ or the RTC wakeup events.
+ [..] The RTC provides a programmable time base for waking up from the
+ Stop or Standby mode at regular intervals.
+ Wakeup from STOP and Standby modes is possible only when the RTC clock source
+ is LSE or LSI.
+
+ *** Callback registration ***
+ =============================================
+
+ The compilation define USE_RTC_REGISTER_CALLBACKS when set to 1
+ allows the user to configure dynamically the driver callbacks.
+ Use Function @ref HAL_RTC_RegisterCallback() to register an interrupt callback.
+
+ Function @ref HAL_RTC_RegisterCallback() allows to register following callbacks:
+ (+) AlarmAEventCallback : RTC Alarm A Event callback.
+ (+) AlarmBEventCallback : RTC Alarm B Event callback.
+ (+) TimeStampEventCallback : RTC TimeStamp Event callback.
+ (+) WakeUpTimerEventCallback : RTC WakeUpTimer Event callback.
+ (+) Tamper1EventCallback : RTC Tamper 1 Event callback.
+ (+) Tamper2EventCallback : RTC Tamper 2 Event callback.
+ (+) Tamper3EventCallback : RTC Tamper 3 Event callback.
+ (+) MspInitCallback : RTC MspInit callback.
+ (+) MspDeInitCallback : RTC MspDeInit callback.
+ This function takes as parameters the HAL peripheral handle, the Callback ID
+ and a pointer to the user callback function.
+
+ Use function @ref HAL_RTC_UnRegisterCallback() to reset a callback to the default
+ weak function.
+ @ref HAL_RTC_UnRegisterCallback() takes as parameters the HAL peripheral handle,
+ and the Callback ID.
+ This function allows to reset following callbacks:
+ (+) AlarmAEventCallback : RTC Alarm A Event callback.
+ (+) AlarmBEventCallback : RTC Alarm B Event callback.
+ (+) TimeStampEventCallback : RTC TimeStamp Event callback.
+ (+) WakeUpTimerEventCallback : RTC WakeUpTimer Event callback.
+ (+) Tamper1EventCallback : RTC Tamper 1 Event callback.
+ (+) Tamper2EventCallback : RTC Tamper 2 Event callback.
+ (+) Tamper3EventCallback : RTC Tamper 3 Event callback.
+ (+) MspInitCallback : RTC MspInit callback.
+ (+) MspDeInitCallback : RTC MspDeInit callback.
+
+ By default, after the @ref HAL_RTC_Init() and when the state is HAL_RTC_STATE_RESET,
+ all callbacks are set to the corresponding weak functions :
+ examples @ref AlarmAEventCallback(), @ref WakeUpTimerEventCallback().
+ Exception done for MspInit and MspDeInit callbacks that are reset to the legacy weak function
+ in the @ref HAL_RTC_Init()/@ref HAL_RTC_DeInit() only when these callbacks are null
+ (not registered beforehand).
+ If not, MspInit or MspDeInit are not null, @ref HAL_RTC_Init()/@ref HAL_RTC_DeInit()
+ keep and use the user MspInit/MspDeInit callbacks (registered beforehand)
+
+ Callbacks can be registered/unregistered in HAL_RTC_STATE_READY state only.
+ Exception done MspInit/MspDeInit that can be registered/unregistered
+ in HAL_RTC_STATE_READY or HAL_RTC_STATE_RESET state,
+ thus registered (user) MspInit/DeInit callbacks can be used during the Init/DeInit.
+ In that case first register the MspInit/MspDeInit user callbacks
+ using @ref HAL_RTC_RegisterCallback() before calling @ref HAL_RTC_DeInit()
+ or @ref HAL_RTC_Init() function.
+
+ When The compilation define USE_HAL_RTC_REGISTER_CALLBACKS is set to 0 or
+ not defined, the callback registration feature is not available and all callbacks
+ are set to the corresponding weak functions.
+ @endverbatim
+
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© Copyright (c) 2017 STMicroelectronics.
+ * All rights reserved.</center></h2>
+ *
+ * This software component is licensed by ST under BSD 3-Clause license,
+ * the "License"; You may not use this file except in compliance with the
+ * License. You may obtain a copy of the License at:
+ * opensource.org/licenses/BSD-3-Clause
+ *
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32h7xx_hal.h"
+
+/** @addtogroup STM32H7xx_HAL_Driver
+ * @{
+ */
+
+/** @defgroup RTC RTC
+ * @brief RTC HAL module driver
+ * @{
+ */
+
+#ifdef HAL_RTC_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/* Private macro -------------------------------------------------------------*/
+/* Private variables ---------------------------------------------------------*/
+/* Private function prototypes -----------------------------------------------*/
+/* Exported functions --------------------------------------------------------*/
+
+/** @defgroup RTC_Exported_Functions RTC Exported Functions
+ * @{
+ */
+
+/** @defgroup RTC_Exported_Functions_Group1 Initialization and de-initialization functions
+ * @brief Initialization and Configuration functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Initialization and de-initialization functions #####
+ ===============================================================================
+ [..] This section provides functions allowing to initialize and configure the
+ RTC Prescaler (Synchronous and Asynchronous), RTC Hour format, disable
+ RTC registers Write protection, enter and exit the RTC initialization mode,
+ RTC registers synchronization check and reference clock detection enable.
+ (#) The RTC Prescaler is programmed to generate the RTC 1Hz time base.
+ It is split into 2 programmable prescalers to minimize power consumption.
+ (++) A 7-bit asynchronous prescaler and a 15-bit synchronous prescaler.
+ (++) When both prescalers are used, it is recommended to configure the
+ asynchronous prescaler to a high value to minimize power consumption.
+ (#) All RTC registers are Write protected. Writing to the RTC registers
+ is enabled by writing a key into the Write Protection register, RTC_WPR.
+ (#) To configure the RTC Calendar, user application should enter
+ initialization mode. In this mode, the calendar counter is stopped
+ and its value can be updated. When the initialization sequence is
+ complete, the calendar restarts counting after 4 RTCCLK cycles.
+ (#) To read the calendar through the shadow registers after Calendar
+ initialization, calendar update or after wakeup from low power modes
+ the software must first clear the RSF flag. The software must then
+ wait until it is set again before reading the calendar, which means
+ that the calendar registers have been correctly copied into the
+ RTC_TR and RTC_DR shadow registers.The HAL_RTC_WaitForSynchro() function
+ implements the above software sequence (RSF clear and RSF check).
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Initialize the RTC according to the specified parameters
+ * in the RTC_InitTypeDef structure.
+ * @param hrtc: RTC handle
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_Init(RTC_HandleTypeDef *hrtc)
+{
+ HAL_StatusTypeDef status = HAL_ERROR;
+
+ /* Check RTC handler */
+ if(hrtc != NULL)
+ {
+ status = HAL_OK;
+
+ /* Check the parameters */
+ assert_param(IS_RTC_ALL_INSTANCE(hrtc->Instance));
+ assert_param(IS_RTC_HOUR_FORMAT(hrtc->Init.HourFormat));
+ assert_param(IS_RTC_ASYNCH_PREDIV(hrtc->Init.AsynchPrediv));
+ assert_param(IS_RTC_SYNCH_PREDIV(hrtc->Init.SynchPrediv));
+ assert_param(IS_RTC_OUTPUT(hrtc->Init.OutPut));
+ assert_param(IS_RTC_OUTPUT_REMAP(hrtc->Init.OutPutRemap));
+ assert_param(IS_RTC_OUTPUT_POL(hrtc->Init.OutPutPolarity));
+ assert_param(IS_RTC_OUTPUT_TYPE(hrtc->Init.OutPutType));
+
+ #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
+ if(hrtc->State == HAL_RTC_STATE_RESET)
+ {
+ /* Allocate lock resource and initialize it */
+ hrtc->Lock = HAL_UNLOCKED;
+
+ hrtc->AlarmAEventCallback = HAL_RTC_AlarmAEventCallback; /* Legacy weak AlarmAEventCallback */
+ hrtc->AlarmBEventCallback = HAL_RTCEx_AlarmBEventCallback; /* Legacy weak AlarmBEventCallback */
+ hrtc->TimeStampEventCallback = HAL_RTCEx_TimeStampEventCallback; /* Legacy weak TimeStampEventCallback */
+ hrtc->WakeUpTimerEventCallback = HAL_RTCEx_WakeUpTimerEventCallback; /* Legacy weak WakeUpTimerEventCallback */
+ hrtc->Tamper1EventCallback = HAL_RTCEx_Tamper1EventCallback; /* Legacy weak Tamper1EventCallback */
+ hrtc->Tamper2EventCallback = HAL_RTCEx_Tamper2EventCallback; /* Legacy weak Tamper2EventCallback */
+ hrtc->Tamper3EventCallback = HAL_RTCEx_Tamper3EventCallback; /* Legacy weak Tamper3EventCallback */
+
+ if(hrtc->MspInitCallback == NULL)
+ {
+ hrtc->MspInitCallback = HAL_RTC_MspInit;
+ }
+ /* Init the low level hardware */
+ hrtc->MspInitCallback(hrtc);
+
+ if(hrtc->MspDeInitCallback == NULL)
+ {
+ hrtc->MspDeInitCallback = HAL_RTC_MspDeInit;
+ }
+ }
+ #else
+ if(hrtc->State == HAL_RTC_STATE_RESET)
+ {
+ /* Allocate lock resource and initialize it */
+ hrtc->Lock = HAL_UNLOCKED;
+
+ /* Initialize RTC MSP */
+ HAL_RTC_MspInit(hrtc);
+ }
+ #endif /* (USE_HAL_RTC_REGISTER_CALLBACKS) */
+
+ /* Set RTC state */
+ hrtc->State = HAL_RTC_STATE_BUSY;
+
+ /* Disable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
+
+ /* Set Initialization mode */
+ if(RTC_EnterInitMode(hrtc) != HAL_OK)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ /* Set RTC state */
+ hrtc->State = HAL_RTC_STATE_ERROR;
+
+ status = HAL_ERROR;
+ }
+ else
+ {
+ /* Clear RTC_CR FMT, OSEL and POL Bits */
+ hrtc->Instance->CR &= (~(RTC_CR_FMT | RTC_CR_OSEL | RTC_CR_POL));
+ /* Set RTC_CR FMT, OSEL and POL Bits to specified values */
+ hrtc->Instance->CR |= (hrtc->Init.HourFormat | hrtc->Init.OutPut | hrtc->Init.OutPutPolarity);
+
+ /* Configure the RTC PRER */
+ hrtc->Instance->PRER = (hrtc->Init.SynchPrediv);
+ hrtc->Instance->PRER |= (hrtc->Init.AsynchPrediv << RTC_PRER_PREDIV_A_Pos);
+
+ /* Exit Initialization mode */
+ hrtc->Instance->ISR &= (~RTC_ISR_INIT);
+
+ /* Clear RTC_OR ALARMOUTTYPE and OUT_RMP Bits */
+ hrtc->Instance->OR &= (~(RTC_OR_ALARMOUTTYPE | RTC_OR_OUT_RMP));
+ /* Set RTC_OR ALARMOUTTYPE and OUT_RMP Bits to specified values */
+ hrtc->Instance->OR |= (hrtc->Init.OutPutType | hrtc->Init.OutPutRemap);
+
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ /* Set RTC state */
+ hrtc->State = HAL_RTC_STATE_READY;
+ }
+ }
+
+ /* return status */
+ return status;
+}
+
+/**
+ * @brief DeInitialize the RTC peripheral.
+ * @param hrtc RTC handle
+ * @note This function doesn't reset the RTC Backup Data registers.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_DeInit(RTC_HandleTypeDef *hrtc)
+{
+ HAL_StatusTypeDef status = HAL_ERROR;
+ uint32_t tickstart;
+
+ /* Check RTC handler */
+ if(hrtc != NULL)
+ {
+ status = HAL_OK;
+
+ /* Check the parameters */
+ assert_param(IS_RTC_ALL_INSTANCE(hrtc->Instance));
+
+ /* Set RTC state */
+ hrtc->State = HAL_RTC_STATE_BUSY;
+
+ /* Disable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
+
+ /* Set Initialization mode */
+ if(RTC_EnterInitMode(hrtc) != HAL_OK)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ /* Set RTC state */
+ hrtc->State = HAL_RTC_STATE_ERROR;
+
+ status = HAL_ERROR;
+ }
+ else
+ {
+ /* Reset TR, DR and CR registers */
+ hrtc->Instance->TR = 0x00000000u;
+ hrtc->Instance->DR = ((uint32_t)(RTC_DR_WDU_0 | RTC_DR_MU_0 | RTC_DR_DU_0));
+ /* Reset All CR bits except CR[2:0] */
+ hrtc->Instance->CR &= RTC_CR_WUCKSEL;
+
+ tickstart = HAL_GetTick();
+
+ /* Wait till WUTWF flag is set and if Time out is reached exit */
+ while(((hrtc->Instance->ISR) & RTC_ISR_WUTWF) == 0u)
+ {
+ if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ /* Set RTC state */
+ hrtc->State = HAL_RTC_STATE_TIMEOUT;
+
+ status = HAL_TIMEOUT;
+ }
+ }
+ }
+
+ if(status == HAL_OK)
+ {
+ /* Reset all RTC CR register bits */
+ hrtc->Instance->CR &= 0x00000000u;
+ /* Reset other RTC registers */
+ hrtc->Instance->WUTR = RTC_WUTR_WUT;
+ hrtc->Instance->PRER = ((uint32_t)(RTC_PRER_PREDIV_A | 0x000000FFU));
+ hrtc->Instance->ALRMAR = 0x00000000u;
+ hrtc->Instance->ALRMBR = 0x00000000u;
+ hrtc->Instance->SHIFTR = 0x00000000u;
+ hrtc->Instance->CALR = 0x00000000u;
+ hrtc->Instance->ALRMASSR = 0x00000000u;
+ hrtc->Instance->ALRMBSSR = 0x00000000u;
+
+ /* Reset Tamper configuration register */
+ hrtc->Instance->TAMPCR = 0x00000000u;
+
+ /* Reset Option register */
+ hrtc->Instance->OR = 0x00000000u;
+
+ /* Reset ISR register and exit initialization mode */
+ hrtc->Instance->ISR = 0x00000000u;
+
+ /* If RTC_CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */
+ if((hrtc->Instance->CR & RTC_CR_BYPSHAD) == 0u)
+ {
+ if(HAL_RTC_WaitForSynchro(hrtc) != HAL_OK)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_ERROR;
+
+ status = HAL_ERROR;
+ }
+ }
+ }
+
+ if(status == HAL_OK)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
+ if(hrtc->MspDeInitCallback == NULL)
+ {
+ hrtc->MspDeInitCallback = HAL_RTC_MspDeInit;
+ }
+
+ /* DeInit the low level hardware: CLOCK, NVIC.*/
+ hrtc->MspDeInitCallback(hrtc);
+
+ #else
+ /* De-Initialize RTC MSP */
+ HAL_RTC_MspDeInit(hrtc);
+ #endif /* (USE_HAL_RTC_REGISTER_CALLBACKS) */
+
+ hrtc->State = HAL_RTC_STATE_RESET;
+
+ /* Release Lock */
+ __HAL_UNLOCK(hrtc);
+ }
+ }
+
+ /* return status */
+ return status;
+}
+
+#if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
+/**
+ * @brief Register a User RTC Callback
+ * To be used instead of the weak predefined callback
+ * @param hrtc RTC handle
+ * @param CallbackID ID of the callback to be registered
+ * This parameter can be one of the following values:
+ * @arg @ref HAL_RTC_ALARM_A_EVENT_CB_ID Alarm A Event Callback ID
+ * @arg @ref HAL_RTC_ALARM_B_EVENT_CB_ID Alarm B Event Callback ID
+ * @arg @ref HAL_RTC_TIMESTAMP_EVENT_CB_ID TimeStamp Event Callback ID
+ * @arg @ref HAL_RTC_WAKEUPTIMER_EVENT_CB_ID WakeUp Timer Event Callback ID
+ * @arg @ref HAL_RTC_TAMPER1_EVENT_CB_ID Tamper 1 Callback ID
+ * @arg @ref HAL_RTC_TAMPER2_EVENT_CB_ID Tamper 2 Callback ID
+ * @arg @ref HAL_RTC_TAMPER3_EVENT_CB_ID Tamper 3 Callback ID
+ * @arg @ref HAL_RTC_MSPINIT_CB_ID Msp Init callback ID
+ * @arg @ref HAL_RTC_MSPDEINIT_CB_ID Msp DeInit callback ID
+ * @param pCallback pointer to the Callback function
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_RegisterCallback(RTC_HandleTypeDef *hrtc, HAL_RTC_CallbackIDTypeDef CallbackID, pRTC_CallbackTypeDef pCallback)
+{
+ HAL_StatusTypeDef status = HAL_OK;
+
+ if(pCallback == NULL)
+ {
+ return HAL_ERROR;
+ }
+
+ /* Process locked */
+ __HAL_LOCK(hrtc);
+
+ if(HAL_RTC_STATE_READY == hrtc->State)
+ {
+ switch (CallbackID)
+ {
+ case HAL_RTC_ALARM_A_EVENT_CB_ID :
+ hrtc->AlarmAEventCallback = pCallback;
+ break;
+
+ case HAL_RTC_ALARM_B_EVENT_CB_ID :
+ hrtc->AlarmBEventCallback = pCallback;
+ break;
+
+ case HAL_RTC_TIMESTAMP_EVENT_CB_ID :
+ hrtc->TimeStampEventCallback = pCallback;
+ break;
+
+ case HAL_RTC_WAKEUPTIMER_EVENT_CB_ID :
+ hrtc->WakeUpTimerEventCallback = pCallback;
+ break;
+
+ case HAL_RTC_TAMPER1_EVENT_CB_ID :
+ hrtc->Tamper1EventCallback = pCallback;
+ break;
+
+ case HAL_RTC_TAMPER2_EVENT_CB_ID :
+ hrtc->Tamper2EventCallback = pCallback;
+ break;
+
+ case HAL_RTC_TAMPER3_EVENT_CB_ID :
+ hrtc->Tamper3EventCallback = pCallback;
+ break;
+
+ case HAL_RTC_MSPINIT_CB_ID :
+ hrtc->MspInitCallback = pCallback;
+ break;
+
+ case HAL_RTC_MSPDEINIT_CB_ID :
+ hrtc->MspDeInitCallback = pCallback;
+ break;
+
+ default :
+ /* Return error status */
+ status = HAL_ERROR;
+ break;
+ }
+ }
+ else if(HAL_RTC_STATE_RESET == hrtc->State)
+ {
+ switch (CallbackID)
+ {
+ case HAL_RTC_MSPINIT_CB_ID :
+ hrtc->MspInitCallback = pCallback;
+ break;
+
+ case HAL_RTC_MSPDEINIT_CB_ID :
+ hrtc->MspDeInitCallback = pCallback;
+ break;
+
+ default :
+ /* Return error status */
+ status = HAL_ERROR;
+ break;
+ }
+ }
+ else
+ {
+ /* Return error status */
+ status = HAL_ERROR;
+ }
+
+ /* Release Lock */
+ __HAL_UNLOCK(hrtc);
+
+ return status;
+}
+
+/**
+ * @brief Unregister an RTC Callback
+ * RTC callabck is redirected to the weak predefined callback
+ * @param hrtc RTC handle
+ * @param CallbackID ID of the callback to be unregistered
+ * This parameter can be one of the following values:
+ * @arg @ref HAL_RTC_ALARM_A_EVENT_CB_ID Alarm A Event Callback ID
+ * @arg @ref HAL_RTC_ALARM_B_EVENT_CB_ID Alarm B Event Callback ID
+ * @arg @ref HAL_RTC_TIMESTAMP_EVENT_CB_ID TimeStamp Event Callback ID
+ * @arg @ref HAL_RTC_WAKEUPTIMER_EVENT_CB_ID WakeUp Timer Event Callback ID
+ * @arg @ref HAL_RTC_TAMPER1_EVENT_CB_ID Tamper 1 Callback ID
+ * @arg @ref HAL_RTC_TAMPER2_EVENT_CB_ID Tamper 2 Callback ID
+ * @arg @ref HAL_RTC_TAMPER3_EVENT_CB_ID Tamper 3 Callback ID
+ * @arg @ref HAL_RTC_MSPINIT_CB_ID Msp Init callback ID
+ * @arg @ref HAL_RTC_MSPDEINIT_CB_ID Msp DeInit callback ID
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_UnRegisterCallback(RTC_HandleTypeDef *hrtc, HAL_RTC_CallbackIDTypeDef CallbackID)
+{
+ HAL_StatusTypeDef status = HAL_OK;
+
+ /* Process locked */
+ __HAL_LOCK(hrtc);
+
+ if(HAL_RTC_STATE_READY == hrtc->State)
+ {
+ switch (CallbackID)
+ {
+ case HAL_RTC_ALARM_A_EVENT_CB_ID :
+ hrtc->AlarmAEventCallback = HAL_RTC_AlarmAEventCallback; /* Legacy weak AlarmAEventCallback */
+ break;
+
+ case HAL_RTC_ALARM_B_EVENT_CB_ID :
+ hrtc->AlarmBEventCallback = HAL_RTCEx_AlarmBEventCallback; /* Legacy weak AlarmBEventCallback */
+ break;
+
+ case HAL_RTC_TIMESTAMP_EVENT_CB_ID :
+ hrtc->TimeStampEventCallback = HAL_RTCEx_TimeStampEventCallback; /* Legacy weak TimeStampEventCallback */
+ break;
+
+ case HAL_RTC_WAKEUPTIMER_EVENT_CB_ID :
+ hrtc->WakeUpTimerEventCallback = HAL_RTCEx_WakeUpTimerEventCallback; /* Legacy weak WakeUpTimerEventCallback */
+ break;
+
+ case HAL_RTC_TAMPER1_EVENT_CB_ID :
+ hrtc->Tamper1EventCallback = HAL_RTCEx_Tamper1EventCallback; /* Legacy weak Tamper1EventCallback */
+ break;
+
+ case HAL_RTC_TAMPER2_EVENT_CB_ID :
+ hrtc->Tamper2EventCallback = HAL_RTCEx_Tamper2EventCallback; /* Legacy weak Tamper2EventCallback */
+ break;
+
+ case HAL_RTC_TAMPER3_EVENT_CB_ID :
+ hrtc->Tamper3EventCallback = HAL_RTCEx_Tamper3EventCallback; /* Legacy weak Tamper3EventCallback */
+ break;
+
+ case HAL_RTC_MSPINIT_CB_ID :
+ hrtc->MspInitCallback = HAL_RTC_MspInit;
+ break;
+
+ case HAL_RTC_MSPDEINIT_CB_ID :
+ hrtc->MspDeInitCallback = HAL_RTC_MspDeInit;
+ break;
+
+ default :
+ /* Return error status */
+ status = HAL_ERROR;
+ break;
+ }
+ }
+ else if(HAL_RTC_STATE_RESET == hrtc->State)
+ {
+ switch (CallbackID)
+ {
+ case HAL_RTC_MSPINIT_CB_ID :
+ hrtc->MspInitCallback = HAL_RTC_MspInit;
+ break;
+
+ case HAL_RTC_MSPDEINIT_CB_ID :
+ hrtc->MspDeInitCallback = HAL_RTC_MspDeInit;
+ break;
+
+ default :
+ /* Return error status */
+ status = HAL_ERROR;
+ break;
+ }
+ }
+ else
+ {
+ /* Return error status */
+ status = HAL_ERROR;
+ }
+
+ /* Release Lock */
+ __HAL_UNLOCK(hrtc);
+
+ return status;
+}
+#endif /* USE_HAL_RTC_REGISTER_CALLBACKS */
+/**
+ * @brief Initialize the RTC MSP.
+ * @param hrtc RTC handle
+ * @retval None
+ */
+__weak void HAL_RTC_MspInit(RTC_HandleTypeDef* hrtc)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(hrtc);
+
+ /* NOTE : This function should not be modified, when the callback is needed,
+ the HAL_RTC_MspInit could be implemented in the user file
+ */
+}
+
+/**
+ * @brief DeInitialize the RTC MSP.
+ * @param hrtc RTC handle
+ * @retval None
+ */
+__weak void HAL_RTC_MspDeInit(RTC_HandleTypeDef* hrtc)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(hrtc);
+
+ /* NOTE : This function should not be modified, when the callback is needed,
+ the HAL_RTC_MspDeInit could be implemented in the user file
+ */
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup RTC_Exported_Functions_Group2 RTC Time and Date functions
+ * @brief RTC Time and Date functions
+ *
+@verbatim
+ ===============================================================================
+ ##### RTC Time and Date functions #####
+ ===============================================================================
+
+ [..] This section provides functions allowing to configure Time and Date features
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Set RTC current time.
+ * @param hrtc RTC handle
+ * @param sTime Pointer to Time structure
+ * @param Format Specifies the format of the entered parameters.
+ * This parameter can be one of the following values:
+ * @arg RTC_FORMAT_BIN: Binary data format
+ * @arg RTC_FORMAT_BCD: BCD data format
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_SetTime(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTime, uint32_t Format)
+{
+ uint32_t tmpreg;
+
+ /* Check the parameters */
+ assert_param(IS_RTC_FORMAT(Format));
+ assert_param(IS_RTC_DAYLIGHT_SAVING(sTime->DayLightSaving));
+ assert_param(IS_RTC_STORE_OPERATION(sTime->StoreOperation));
+
+ /* Process Locked */
+ __HAL_LOCK(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_BUSY;
+
+ if(Format == RTC_FORMAT_BIN)
+ {
+ if((hrtc->Instance->CR & RTC_CR_FMT) != 0u)
+ {
+ assert_param(IS_RTC_HOUR12(sTime->Hours));
+ assert_param(IS_RTC_HOURFORMAT12(sTime->TimeFormat));
+ }
+ else
+ {
+ sTime->TimeFormat = 0x00u;
+ assert_param(IS_RTC_HOUR24(sTime->Hours));
+ }
+ assert_param(IS_RTC_MINUTES(sTime->Minutes));
+ assert_param(IS_RTC_SECONDS(sTime->Seconds));
+
+ tmpreg = (uint32_t)(( (uint32_t)RTC_ByteToBcd2(sTime->Hours) << RTC_TR_HU_Pos) | \
+ ( (uint32_t)RTC_ByteToBcd2(sTime->Minutes) << RTC_TR_MNU_Pos) | \
+ ( (uint32_t)RTC_ByteToBcd2(sTime->Seconds)) | \
+ (((uint32_t)sTime->TimeFormat) << RTC_TR_PM_Pos));
+ }
+ else
+ {
+ if((hrtc->Instance->CR & RTC_CR_FMT) != 0u)
+ {
+ assert_param(IS_RTC_HOUR12(RTC_Bcd2ToByte(sTime->Hours)));
+ assert_param(IS_RTC_HOURFORMAT12(sTime->TimeFormat));
+ }
+ else
+ {
+ sTime->TimeFormat = 0x00u;
+ assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sTime->Hours)));
+ }
+ assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sTime->Minutes)));
+ assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sTime->Seconds)));
+ tmpreg = (((uint32_t)(sTime->Hours) << RTC_TR_HU_Pos) | \
+ ((uint32_t)(sTime->Minutes) << RTC_TR_MNU_Pos) | \
+ ((uint32_t) sTime->Seconds) | \
+ ((uint32_t)(sTime->TimeFormat) << RTC_TR_PM_Pos));
+ }
+
+ /* Disable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
+
+ /* Set Initialization mode */
+ if(RTC_EnterInitMode(hrtc) != HAL_OK)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ /* Set RTC state */
+ hrtc->State = HAL_RTC_STATE_ERROR;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_ERROR;
+ }
+ else
+ {
+ /* Set the RTC_TR register */
+ hrtc->Instance->TR = (uint32_t)(tmpreg & RTC_TR_RESERVED_MASK);
+
+ /* Clear the bits to be configured */
+ hrtc->Instance->CR &= ((uint32_t)~RTC_CR_BKP);
+
+ /* Configure the RTC_CR register */
+ hrtc->Instance->CR |= (uint32_t)(sTime->DayLightSaving | sTime->StoreOperation);
+
+ /* Exit Initialization mode */
+ hrtc->Instance->ISR &= (~RTC_ISR_INIT);
+
+ /* If CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */
+ if((hrtc->Instance->CR & RTC_CR_BYPSHAD) == 0u)
+ {
+ if(HAL_RTC_WaitForSynchro(hrtc) != HAL_OK)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_ERROR;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_ERROR;
+ }
+ }
+
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_READY;
+
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_OK;
+ }
+}
+
+/**
+ * @brief Get RTC current time.
+ * @param hrtc RTC handle
+ * @param sTime Pointer to Time structure with Hours, Minutes and Seconds fields returned
+ * with input format (BIN or BCD), also SubSeconds field returning the
+ * RTC_SSR register content and SecondFraction field the Synchronous pre-scaler
+ * factor to be used for second fraction ratio computation.
+ * @param Format Specifies the format of the entered parameters.
+ * This parameter can be one of the following values:
+ * @arg RTC_FORMAT_BIN: Binary data format
+ * @arg RTC_FORMAT_BCD: BCD data format
+ * @note You can use SubSeconds and SecondFraction (sTime structure fields returned) to convert SubSeconds
+ * value in second fraction ratio with time unit following generic formula:
+ * Second fraction ratio * time_unit= [(SecondFraction-SubSeconds)/(SecondFraction+1)] * time_unit
+ * This conversion can be performed only if no shift operation is pending (ie. SHFP=0) when PREDIV_S >= SS
+ * @note You must call HAL_RTC_GetDate() after HAL_RTC_GetTime() to unlock the values
+ * in the higher-order calendar shadow registers to ensure consistency between the time and date values.
+ * Reading RTC current time locks the values in calendar shadow registers until Current date is read
+ * to ensure consistency between the time and date values.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_GetTime(RTC_HandleTypeDef *hrtc, RTC_TimeTypeDef *sTime, uint32_t Format)
+{
+ uint32_t tmpreg;
+
+ /* Check the parameters */
+ assert_param(IS_RTC_FORMAT(Format));
+
+ /* Get subseconds structure field from the corresponding register*/
+ sTime->SubSeconds = (uint32_t)(hrtc->Instance->SSR);
+
+ /* Get SecondFraction structure field from the corresponding register field*/
+ sTime->SecondFraction = (uint32_t)(hrtc->Instance->PRER & RTC_PRER_PREDIV_S);
+
+ /* Get the TR register */
+ tmpreg = (uint32_t)(hrtc->Instance->TR & RTC_TR_RESERVED_MASK);
+
+ /* Fill the structure fields with the read parameters */
+ sTime->Hours = (uint8_t)((tmpreg & (RTC_TR_HT | RTC_TR_HU)) >> RTC_TR_HU_Pos);
+ sTime->Minutes = (uint8_t)((tmpreg & (RTC_TR_MNT | RTC_TR_MNU)) >> RTC_TR_MNU_Pos);
+ sTime->Seconds = (uint8_t)( tmpreg & (RTC_TR_ST | RTC_TR_SU));
+ sTime->TimeFormat = (uint8_t)((tmpreg & (RTC_TR_PM)) >> RTC_TR_PM_Pos);
+
+ /* Check the input parameters format */
+ if(Format == RTC_FORMAT_BIN)
+ {
+ /* Convert the time structure parameters to Binary format */
+ sTime->Hours = (uint8_t)RTC_Bcd2ToByte(sTime->Hours);
+ sTime->Minutes = (uint8_t)RTC_Bcd2ToByte(sTime->Minutes);
+ sTime->Seconds = (uint8_t)RTC_Bcd2ToByte(sTime->Seconds);
+ }
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Set RTC current date.
+ * @param hrtc RTC handle
+ * @param sDate Pointer to date structure
+ * @param Format specifies the format of the entered parameters.
+ * This parameter can be one of the following values:
+ * @arg RTC_FORMAT_BIN: Binary data format
+ * @arg RTC_FORMAT_BCD: BCD data format
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_SetDate(RTC_HandleTypeDef *hrtc, RTC_DateTypeDef *sDate, uint32_t Format)
+{
+ uint32_t datetmpreg;
+
+ /* Check the parameters */
+ assert_param(IS_RTC_FORMAT(Format));
+
+ /* Process Locked */
+ __HAL_LOCK(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_BUSY;
+
+ if((Format == RTC_FORMAT_BIN) && ((sDate->Month & 0x10U) == 0x10U))
+ {
+ sDate->Month = (uint8_t)((sDate->Month & (uint8_t)~(0x10U)) + (uint8_t)0x0AU);
+ }
+
+ assert_param(IS_RTC_WEEKDAY(sDate->WeekDay));
+
+ if(Format == RTC_FORMAT_BIN)
+ {
+ assert_param(IS_RTC_YEAR(sDate->Year));
+ assert_param(IS_RTC_MONTH(sDate->Month));
+ assert_param(IS_RTC_DATE(sDate->Date));
+
+ datetmpreg = (((uint32_t)RTC_ByteToBcd2(sDate->Year) << RTC_DR_YU_Pos) | \
+ ((uint32_t)RTC_ByteToBcd2(sDate->Month) << RTC_DR_MU_Pos) | \
+ ((uint32_t)RTC_ByteToBcd2(sDate->Date)) | \
+ ((uint32_t)sDate->WeekDay << RTC_DR_WDU_Pos));
+ }
+ else
+ {
+ assert_param(IS_RTC_YEAR(RTC_Bcd2ToByte(sDate->Year)));
+ assert_param(IS_RTC_MONTH(RTC_Bcd2ToByte(sDate->Month)));
+ assert_param(IS_RTC_DATE (RTC_Bcd2ToByte(sDate->Date)));
+
+ datetmpreg = ((((uint32_t)sDate->Year) << RTC_DR_YU_Pos) | \
+ (((uint32_t)sDate->Month) << RTC_DR_MU_Pos) | \
+ ((uint32_t) sDate->Date) | \
+ (((uint32_t)sDate->WeekDay) << RTC_DR_WDU_Pos));
+ }
+
+ /* Disable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
+
+ /* Set Initialization mode */
+ if(RTC_EnterInitMode(hrtc) != HAL_OK)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ /* Set RTC state*/
+ hrtc->State = HAL_RTC_STATE_ERROR;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_ERROR;
+ }
+ else
+ {
+ /* Set the RTC_DR register */
+ hrtc->Instance->DR = (uint32_t)(datetmpreg & RTC_DR_RESERVED_MASK);
+
+ /* Exit Initialization mode */
+ hrtc->Instance->ISR &= (~RTC_ISR_INIT);
+
+ /* If CR_BYPSHAD bit = 0, wait for synchro else this check is not needed */
+ if((hrtc->Instance->CR & RTC_CR_BYPSHAD) == 0u)
+ {
+ if(HAL_RTC_WaitForSynchro(hrtc) != HAL_OK)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_ERROR;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_ERROR;
+ }
+ }
+
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_READY ;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_OK;
+ }
+}
+
+/**
+ * @brief Get RTC current date.
+ * @param hrtc RTC handle
+ * @param sDate Pointer to Date structure
+ * @param Format Specifies the format of the entered parameters.
+ * This parameter can be one of the following values:
+ * @arg RTC_FORMAT_BIN: Binary data format
+ * @arg RTC_FORMAT_BCD: BCD data format
+ * @note You must call HAL_RTC_GetDate() after HAL_RTC_GetTime() to unlock the values
+ * in the higher-order calendar shadow registers to ensure consistency between the time and date values.
+ * Reading RTC current time locks the values in calendar shadow registers until Current date is read.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_GetDate(RTC_HandleTypeDef *hrtc, RTC_DateTypeDef *sDate, uint32_t Format)
+{
+ uint32_t datetmpreg;
+
+ /* Check the parameters */
+ assert_param(IS_RTC_FORMAT(Format));
+
+ /* Get the DR register */
+ datetmpreg = (uint32_t)(hrtc->Instance->DR & RTC_DR_RESERVED_MASK);
+
+ /* Fill the structure fields with the read parameters */
+ sDate->Year = (uint8_t)((datetmpreg & (RTC_DR_YT | RTC_DR_YU)) >> RTC_DR_YU_Pos);
+ sDate->Month = (uint8_t)((datetmpreg & (RTC_DR_MT | RTC_DR_MU)) >> RTC_DR_MU_Pos);
+ sDate->Date = (uint8_t) (datetmpreg & (RTC_DR_DT | RTC_DR_DU));
+ sDate->WeekDay = (uint8_t)((datetmpreg & (RTC_DR_WDU)) >> RTC_DR_WDU_Pos);
+
+ /* Check the input parameters format */
+ if(Format == RTC_FORMAT_BIN)
+ {
+ /* Convert the date structure parameters to Binary format */
+ sDate->Year = (uint8_t)RTC_Bcd2ToByte(sDate->Year);
+ sDate->Month = (uint8_t)RTC_Bcd2ToByte(sDate->Month);
+ sDate->Date = (uint8_t)RTC_Bcd2ToByte(sDate->Date);
+ }
+ return HAL_OK;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup RTC_Exported_Functions_Group3 RTC Alarm functions
+ * @brief RTC Alarm functions
+ *
+@verbatim
+ ===============================================================================
+ ##### RTC Alarm functions #####
+ ===============================================================================
+
+ [..] This section provides functions allowing to configure Alarm feature
+
+@endverbatim
+ * @{
+ */
+/**
+ * @brief Set the specified RTC Alarm.
+ * @param hrtc RTC handle
+ * @param sAlarm Pointer to Alarm structure
+ * @param Format Specifies the format of the entered parameters.
+ * This parameter can be one of the following values:
+ * @arg RTC_FORMAT_BIN: Binary data format
+ * @arg RTC_FORMAT_BCD: BCD data format
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_SetAlarm(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Format)
+{
+ uint32_t tickstart;
+ uint32_t tmpreg;
+ uint32_t subsecondtmpreg;
+
+ /* Check the parameters */
+ assert_param(IS_RTC_FORMAT(Format));
+ assert_param(IS_RTC_ALARM(sAlarm->Alarm));
+ assert_param(IS_RTC_ALARM_MASK(sAlarm->AlarmMask));
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_SEL(sAlarm->AlarmDateWeekDaySel));
+ assert_param(IS_RTC_ALARM_SUB_SECOND_VALUE(sAlarm->AlarmTime.SubSeconds));
+ assert_param(IS_RTC_ALARM_SUB_SECOND_MASK(sAlarm->AlarmSubSecondMask));
+
+ /* Process Locked */
+ __HAL_LOCK(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_BUSY;
+
+ if(Format == RTC_FORMAT_BIN)
+ {
+ if((hrtc->Instance->CR & RTC_CR_FMT) != 0u)
+ {
+ assert_param(IS_RTC_HOUR12(sAlarm->AlarmTime.Hours));
+ assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat));
+ }
+ else
+ {
+ sAlarm->AlarmTime.TimeFormat = 0x00u;
+ assert_param(IS_RTC_HOUR24(sAlarm->AlarmTime.Hours));
+ }
+ assert_param(IS_RTC_MINUTES(sAlarm->AlarmTime.Minutes));
+ assert_param(IS_RTC_SECONDS(sAlarm->AlarmTime.Seconds));
+
+ if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(sAlarm->AlarmDateWeekDay));
+ }
+ else
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(sAlarm->AlarmDateWeekDay));
+ }
+
+ tmpreg = (((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Hours) << RTC_ALRMAR_HU_Pos) | \
+ ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Minutes) << RTC_ALRMAR_MNU_Pos) | \
+ ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Seconds)) | \
+ ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << RTC_TR_PM_Pos) | \
+ ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmDateWeekDay) << RTC_ALRMAR_DU_Pos) | \
+ ((uint32_t)sAlarm->AlarmDateWeekDaySel) | \
+ ((uint32_t)sAlarm->AlarmMask));
+ }
+ else
+ {
+ if((hrtc->Instance->CR & RTC_CR_FMT) != 0u)
+ {
+ assert_param(IS_RTC_HOUR12(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours)));
+ assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat));
+ }
+ else
+ {
+ sAlarm->AlarmTime.TimeFormat = 0x00u;
+ assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours)));
+ }
+
+ assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes)));
+ assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds)));
+
+ if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay)));
+ }
+ else
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay)));
+ }
+
+ tmpreg = (((uint32_t)(sAlarm->AlarmTime.Hours) << RTC_ALRMAR_HU_Pos) | \
+ ((uint32_t)(sAlarm->AlarmTime.Minutes) << RTC_ALRMAR_MNU_Pos) | \
+ ((uint32_t) sAlarm->AlarmTime.Seconds) | \
+ ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << RTC_TR_PM_Pos) | \
+ ((uint32_t)(sAlarm->AlarmDateWeekDay) << RTC_ALRMAR_DU_Pos) | \
+ ((uint32_t) sAlarm->AlarmDateWeekDaySel) | \
+ ((uint32_t) sAlarm->AlarmMask));
+ }
+
+ /* Configure the Alarm A or Alarm B Sub Second registers */
+ subsecondtmpreg = (uint32_t)((uint32_t)(sAlarm->AlarmTime.SubSeconds) | (uint32_t)(sAlarm->AlarmSubSecondMask));
+
+ /* Disable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
+
+ /* Configure the Alarm register */
+ if(sAlarm->Alarm == RTC_ALARM_A)
+ {
+ /* Disable the Alarm A interrupt */
+ __HAL_RTC_ALARMA_DISABLE(hrtc);
+
+ /* In case of interrupt mode is used, the interrupt source must disabled */
+ __HAL_RTC_ALARM_DISABLE_IT(hrtc, RTC_IT_ALRA);
+
+ tickstart = HAL_GetTick();
+ /* Wait till RTC ALRAWF flag is set and if Time out is reached exit */
+ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAWF) == 0u)
+ {
+ if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_TIMEOUT;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_TIMEOUT;
+ }
+ }
+
+ hrtc->Instance->ALRMAR = (uint32_t)tmpreg;
+ /* Configure the Alarm A Sub Second register */
+ hrtc->Instance->ALRMASSR = subsecondtmpreg;
+ /* Configure the Alarm state: Enable Alarm */
+ __HAL_RTC_ALARMA_ENABLE(hrtc);
+ }
+ else
+ {
+ /* Disable the Alarm B interrupt */
+ __HAL_RTC_ALARMB_DISABLE(hrtc);
+
+ /* In case of interrupt mode is used, the interrupt source must disabled */
+ __HAL_RTC_ALARM_DISABLE_IT(hrtc, RTC_IT_ALRB);
+
+ tickstart = HAL_GetTick();
+ /* Wait till RTC ALRBWF flag is set and if Time out is reached exit */
+ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBWF) == 0u)
+ {
+ if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_TIMEOUT;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_TIMEOUT;
+ }
+ }
+
+ hrtc->Instance->ALRMBR = (uint32_t)tmpreg;
+ /* Configure the Alarm B Sub Second register */
+ hrtc->Instance->ALRMBSSR = subsecondtmpreg;
+ /* Configure the Alarm state: Enable Alarm */
+ __HAL_RTC_ALARMB_ENABLE(hrtc);
+ }
+
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ /* Change RTC state */
+ hrtc->State = HAL_RTC_STATE_READY;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Set the specified RTC Alarm with Interrupt.
+ * @param hrtc RTC handle
+ * @param sAlarm Pointer to Alarm structure
+ * @param Format Specifies the format of the entered parameters.
+ * This parameter can be one of the following values:
+ * @arg RTC_FORMAT_BIN: Binary data format
+ * @arg RTC_FORMAT_BCD: BCD data format
+ * @note The Alarm register can only be written when the corresponding Alarm
+ * is disabled (Use the HAL_RTC_DeactivateAlarm()).
+ * @note The HAL_RTC_SetTime() must be called before enabling the Alarm feature.
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_SetAlarm_IT(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Format)
+{
+ uint32_t tickstart;
+ uint32_t tmpreg;
+ uint32_t subsecondtmpreg;
+
+ /* Check the parameters */
+ assert_param(IS_RTC_FORMAT(Format));
+ assert_param(IS_RTC_ALARM(sAlarm->Alarm));
+ assert_param(IS_RTC_ALARM_MASK(sAlarm->AlarmMask));
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_SEL(sAlarm->AlarmDateWeekDaySel));
+ assert_param(IS_RTC_ALARM_SUB_SECOND_VALUE(sAlarm->AlarmTime.SubSeconds));
+ assert_param(IS_RTC_ALARM_SUB_SECOND_MASK(sAlarm->AlarmSubSecondMask));
+
+ /* Process Locked */
+ __HAL_LOCK(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_BUSY;
+
+ if(Format == RTC_FORMAT_BIN)
+ {
+ if((hrtc->Instance->CR & RTC_CR_FMT) != 0u)
+ {
+ assert_param(IS_RTC_HOUR12(sAlarm->AlarmTime.Hours));
+ assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat));
+ }
+ else
+ {
+ sAlarm->AlarmTime.TimeFormat = 0x00u;
+ assert_param(IS_RTC_HOUR24(sAlarm->AlarmTime.Hours));
+ }
+ assert_param(IS_RTC_MINUTES(sAlarm->AlarmTime.Minutes));
+ assert_param(IS_RTC_SECONDS(sAlarm->AlarmTime.Seconds));
+
+ if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(sAlarm->AlarmDateWeekDay));
+ }
+ else
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(sAlarm->AlarmDateWeekDay));
+ }
+ tmpreg = (((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Hours) << RTC_ALRMAR_HU_Pos) | \
+ ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Minutes) << RTC_ALRMAR_MNU_Pos) | \
+ ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmTime.Seconds)) | \
+ ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << RTC_TR_PM_Pos) | \
+ ((uint32_t)RTC_ByteToBcd2(sAlarm->AlarmDateWeekDay) << RTC_ALRMAR_DU_Pos) | \
+ ((uint32_t)sAlarm->AlarmDateWeekDaySel) | \
+ ((uint32_t)sAlarm->AlarmMask));
+ }
+ else
+ {
+ if((hrtc->Instance->CR & RTC_CR_FMT) != 0u)
+ {
+ assert_param(IS_RTC_HOUR12(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours)));
+ assert_param(IS_RTC_HOURFORMAT12(sAlarm->AlarmTime.TimeFormat));
+ }
+ else
+ {
+ sAlarm->AlarmTime.TimeFormat = 0x00u;
+ assert_param(IS_RTC_HOUR24(RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours)));
+ }
+
+ assert_param(IS_RTC_MINUTES(RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes)));
+ assert_param(IS_RTC_SECONDS(RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds)));
+
+ if(sAlarm->AlarmDateWeekDaySel == RTC_ALARMDATEWEEKDAYSEL_DATE)
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_DATE(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay)));
+ }
+ else
+ {
+ assert_param(IS_RTC_ALARM_DATE_WEEKDAY_WEEKDAY(RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay)));
+ }
+ tmpreg = (((uint32_t)(sAlarm->AlarmTime.Hours) << RTC_ALRMAR_HU_Pos) | \
+ ((uint32_t)(sAlarm->AlarmTime.Minutes) << RTC_ALRMAR_MNU_Pos) | \
+ ((uint32_t) sAlarm->AlarmTime.Seconds) | \
+ ((uint32_t)(sAlarm->AlarmTime.TimeFormat) << RTC_TR_PM_Pos) | \
+ ((uint32_t)(sAlarm->AlarmDateWeekDay) << RTC_ALRMAR_DU_Pos) | \
+ ((uint32_t) sAlarm->AlarmDateWeekDaySel) | \
+ ((uint32_t) sAlarm->AlarmMask));
+ }
+ /* Configure the Alarm A or Alarm B Sub Second registers */
+ subsecondtmpreg = (uint32_t)((uint32_t)(sAlarm->AlarmTime.SubSeconds) | (uint32_t)(sAlarm->AlarmSubSecondMask));
+
+ /* Disable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
+
+ /* Configure the Alarm register */
+ if(sAlarm->Alarm == RTC_ALARM_A)
+ {
+ /* Disable the Alarm A interrupt */
+ __HAL_RTC_ALARMA_DISABLE(hrtc);
+
+ /* Clear flag alarm A */
+ __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRAF);
+
+ tickstart = HAL_GetTick();
+ /* Wait till RTC ALRAWF flag is set and if Time out is reached exit */
+ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAWF) == 0u)
+ {
+ if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_TIMEOUT;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_TIMEOUT;
+ }
+ }
+
+ hrtc->Instance->ALRMAR = (uint32_t)tmpreg;
+ /* Configure the Alarm A Sub Second register */
+ hrtc->Instance->ALRMASSR = subsecondtmpreg;
+ /* Configure the Alarm state: Enable Alarm */
+ __HAL_RTC_ALARMA_ENABLE(hrtc);
+ /* Configure the Alarm interrupt */
+ __HAL_RTC_ALARM_ENABLE_IT(hrtc,RTC_IT_ALRA);
+ }
+ else
+ {
+ /* Disable the Alarm B interrupt */
+ __HAL_RTC_ALARMB_DISABLE(hrtc);
+
+ /* Clear flag alarm B */
+ __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRBF);
+
+ tickstart = HAL_GetTick();
+ /* Wait till RTC ALRBWF flag is set and if Time out is reached exit */
+ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBWF) == 0u)
+ {
+ if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_TIMEOUT;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_TIMEOUT;
+ }
+ }
+
+ hrtc->Instance->ALRMBR = (uint32_t)tmpreg;
+ /* Configure the Alarm B Sub Second register */
+ hrtc->Instance->ALRMBSSR = subsecondtmpreg;
+ /* Configure the Alarm state: Enable Alarm */
+ __HAL_RTC_ALARMB_ENABLE(hrtc);
+ /* Configure the Alarm interrupt */
+ __HAL_RTC_ALARM_ENABLE_IT(hrtc, RTC_IT_ALRB);
+ }
+
+ /* RTC Alarm Interrupt Configuration: EXTI configuration */
+ __HAL_RTC_ALARM_EXTI_ENABLE_IT();
+
+ __HAL_RTC_ALARM_EXTI_ENABLE_RISING_EDGE();
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_READY;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Deactivate the specified RTC Alarm.
+ * @param hrtc RTC handle
+ * @param Alarm Specifies the Alarm.
+ * This parameter can be one of the following values:
+ * @arg RTC_ALARM_A: AlarmA
+ * @arg RTC_ALARM_B: AlarmB
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_DeactivateAlarm(RTC_HandleTypeDef *hrtc, uint32_t Alarm)
+{
+ uint32_t tickstart;
+
+ /* Check the parameters */
+ assert_param(IS_RTC_ALARM(Alarm));
+
+ /* Process Locked */
+ __HAL_LOCK(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_BUSY;
+
+ /* Disable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_DISABLE(hrtc);
+
+ if(Alarm == RTC_ALARM_A)
+ {
+ /* AlarmA */
+ __HAL_RTC_ALARMA_DISABLE(hrtc);
+
+ /* In case of interrupt mode is used, the interrupt source must disabled */
+ __HAL_RTC_ALARM_DISABLE_IT(hrtc, RTC_IT_ALRA);
+
+ tickstart = HAL_GetTick();
+
+ /* Wait till RTC ALRxWF flag is set and if Time out is reached exit */
+ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAWF) == 0u)
+ {
+ if( (HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_TIMEOUT;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ else
+ {
+ /* AlarmB */
+ __HAL_RTC_ALARMB_DISABLE(hrtc);
+
+ /* In case of interrupt mode is used, the interrupt source must disabled */
+ __HAL_RTC_ALARM_DISABLE_IT(hrtc,RTC_IT_ALRB);
+
+ tickstart = HAL_GetTick();
+
+ /* Wait till RTC ALRxWF flag is set and if Time out is reached exit */
+ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBWF) == 0u)
+ {
+ if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
+ {
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_TIMEOUT;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ /* Enable the write protection for RTC registers */
+ __HAL_RTC_WRITEPROTECTION_ENABLE(hrtc);
+
+ hrtc->State = HAL_RTC_STATE_READY;
+
+ /* Process Unlocked */
+ __HAL_UNLOCK(hrtc);
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Get the RTC Alarm value and masks.
+ * @param hrtc RTC handle
+ * @param sAlarm Pointer to Date structure
+ * @param Alarm Specifies the Alarm.
+ * This parameter can be one of the following values:
+ * @arg RTC_ALARM_A: AlarmA
+ * @arg RTC_ALARM_B: AlarmB
+ * @param Format Specifies the format of the entered parameters.
+ * This parameter can be one of the following values:
+ * @arg RTC_FORMAT_BIN: Binary data format
+ * @arg RTC_FORMAT_BCD: BCD data format
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_GetAlarm(RTC_HandleTypeDef *hrtc, RTC_AlarmTypeDef *sAlarm, uint32_t Alarm, uint32_t Format)
+{
+ uint32_t tmpreg;
+ uint32_t subsecondtmpreg;
+
+ /* Check the parameters */
+ assert_param(IS_RTC_FORMAT(Format));
+ assert_param(IS_RTC_ALARM(Alarm));
+
+ if(Alarm == RTC_ALARM_A)
+ {
+ /* AlarmA */
+ sAlarm->Alarm = RTC_ALARM_A;
+
+ tmpreg = (uint32_t)(hrtc->Instance->ALRMAR);
+ subsecondtmpreg = (uint32_t)((hrtc->Instance->ALRMASSR ) & RTC_ALRMASSR_SS);
+
+ /* Fill the structure with the read parameters */
+ sAlarm->AlarmTime.Hours = (uint8_t) ((tmpreg & (RTC_ALRMAR_HT | RTC_ALRMAR_HU)) >> RTC_ALRMAR_HU_Pos);
+ sAlarm->AlarmTime.Minutes = (uint8_t) ((tmpreg & (RTC_ALRMAR_MNT | RTC_ALRMAR_MNU)) >> RTC_ALRMAR_MNU_Pos);
+ sAlarm->AlarmTime.Seconds = (uint8_t) ( tmpreg & (RTC_ALRMAR_ST | RTC_ALRMAR_SU));
+ sAlarm->AlarmTime.TimeFormat = (uint8_t) ((tmpreg & RTC_ALRMAR_PM) >> RTC_TR_PM_Pos);
+ sAlarm->AlarmTime.SubSeconds = (uint32_t) subsecondtmpreg;
+ sAlarm->AlarmDateWeekDay = (uint8_t) ((tmpreg & (RTC_ALRMAR_DT | RTC_ALRMAR_DU)) >> RTC_ALRMAR_DU_Pos);
+ sAlarm->AlarmDateWeekDaySel = (uint32_t) (tmpreg & RTC_ALRMAR_WDSEL);
+ sAlarm->AlarmMask = (uint32_t) (tmpreg & RTC_ALARMMASK_ALL);
+ }
+ else
+ {
+ sAlarm->Alarm = RTC_ALARM_B;
+
+ tmpreg = (uint32_t)(hrtc->Instance->ALRMBR);
+ subsecondtmpreg = (uint32_t)((hrtc->Instance->ALRMBSSR) & RTC_ALRMBSSR_SS);
+
+ /* Fill the structure with the read parameters */
+ sAlarm->AlarmTime.Hours = (uint8_t) ((tmpreg & (RTC_ALRMBR_HT | RTC_ALRMBR_HU)) >> RTC_ALRMBR_HU_Pos);
+ sAlarm->AlarmTime.Minutes = (uint8_t) ((tmpreg & (RTC_ALRMBR_MNT | RTC_ALRMBR_MNU)) >> RTC_ALRMBR_MNU_Pos);
+ sAlarm->AlarmTime.Seconds = (uint8_t) ( tmpreg & (RTC_ALRMBR_ST | RTC_ALRMBR_SU));
+ sAlarm->AlarmTime.TimeFormat = (uint8_t) ((tmpreg & RTC_ALRMBR_PM) >> RTC_TR_PM_Pos);
+ sAlarm->AlarmTime.SubSeconds = (uint32_t) subsecondtmpreg;
+ sAlarm->AlarmDateWeekDay = (uint8_t) ((tmpreg & (RTC_ALRMBR_DT | RTC_ALRMBR_DU)) >> RTC_ALRMBR_DU_Pos);
+ sAlarm->AlarmDateWeekDaySel = (uint32_t) (tmpreg & RTC_ALRMBR_WDSEL);
+ sAlarm->AlarmMask = (uint32_t) (tmpreg & RTC_ALARMMASK_ALL);
+ }
+
+ if(Format == RTC_FORMAT_BIN)
+ {
+ sAlarm->AlarmTime.Hours = RTC_Bcd2ToByte(sAlarm->AlarmTime.Hours);
+ sAlarm->AlarmTime.Minutes = RTC_Bcd2ToByte(sAlarm->AlarmTime.Minutes);
+ sAlarm->AlarmTime.Seconds = RTC_Bcd2ToByte(sAlarm->AlarmTime.Seconds);
+ sAlarm->AlarmDateWeekDay = RTC_Bcd2ToByte(sAlarm->AlarmDateWeekDay);
+ }
+
+ return HAL_OK;
+}
+
+/**
+ * @brief Handle Alarm interrupt request.
+ * @param hrtc RTC handle
+ * @retval None
+ */
+void HAL_RTC_AlarmIRQHandler(RTC_HandleTypeDef* hrtc)
+{
+
+ /* Clear the EXTI's line Flag for RTC Alarm */
+ __HAL_RTC_ALARM_EXTI_CLEAR_FLAG();
+
+ /* Get the AlarmA interrupt source enable status */
+ if(__HAL_RTC_ALARM_GET_IT_SOURCE(hrtc, RTC_IT_ALRA) != 0u)
+ {
+ /* Get the pending status of the AlarmA Interrupt */
+ if(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAF) != 0u)
+ {
+ /* Clear the AlarmA interrupt pending bit */
+ __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRAF);
+
+ /* AlarmA callback */
+ #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
+ hrtc->AlarmAEventCallback(hrtc);
+ #else
+ HAL_RTC_AlarmAEventCallback(hrtc);
+ #endif /* USE_HAL_RTC_REGISTER_CALLBACKS */
+ }
+ }
+
+ /* Get the AlarmB interrupt source enable status */
+ if(__HAL_RTC_ALARM_GET_IT_SOURCE(hrtc, RTC_IT_ALRB) != 0u)
+ {
+ /* Get the pending status of the AlarmB Interrupt */
+ if(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRBF) != 0u)
+ {
+ /* Clear the AlarmB interrupt pending bit */
+ __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRBF);
+
+ /* AlarmB callback */
+ #if (USE_HAL_RTC_REGISTER_CALLBACKS == 1)
+ hrtc->AlarmBEventCallback(hrtc);
+ #else
+ HAL_RTCEx_AlarmBEventCallback(hrtc);
+ #endif /* USE_HAL_RTC_REGISTER_CALLBACKS */
+ }
+ }
+
+ /* Change RTC state */
+ hrtc->State = HAL_RTC_STATE_READY;
+}
+
+/**
+ * @brief Alarm A callback.
+ * @param hrtc RTC handle
+ * @retval None
+ */
+__weak void HAL_RTC_AlarmAEventCallback(RTC_HandleTypeDef *hrtc)
+{
+ /* Prevent unused argument(s) compilation warning */
+ UNUSED(hrtc);
+
+ /* NOTE : This function should not be modified, when the callback is needed,
+ the HAL_RTC_AlarmAEventCallback could be implemented in the user file
+ */
+}
+
+/**
+ * @brief Handle AlarmA Polling request.
+ * @param hrtc RTC handle
+ * @param Timeout Timeout duration
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_PollForAlarmAEvent(RTC_HandleTypeDef *hrtc, uint32_t Timeout)
+{
+
+ uint32_t tickstart = HAL_GetTick();
+
+ while(__HAL_RTC_ALARM_GET_FLAG(hrtc, RTC_FLAG_ALRAF) == 0u)
+ {
+ if(Timeout != HAL_MAX_DELAY)
+ {
+ if(((HAL_GetTick() - tickstart ) > Timeout) || (Timeout == 0U))
+ {
+ hrtc->State = HAL_RTC_STATE_TIMEOUT;
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+
+ /* Clear the Alarm interrupt pending bit */
+ __HAL_RTC_ALARM_CLEAR_FLAG(hrtc, RTC_FLAG_ALRAF);
+
+ /* Change RTC state */
+ hrtc->State = HAL_RTC_STATE_READY;
+
+ return HAL_OK;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup RTC_Exported_Functions_Group4 Peripheral Control functions
+ * @brief Peripheral Control functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Peripheral Control functions #####
+ ===============================================================================
+ [..]
+ This subsection provides functions allowing to
+ (+) Wait for RTC Time and Date Synchronization
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Wait until the RTC Time and Date registers (RTC_TR and RTC_DR) are
+ * synchronized with RTC APB clock.
+ * @note The RTC Resynchronization mode is write protected, use the
+ * __HAL_RTC_WRITEPROTECTION_DISABLE() before calling this function.
+ * @note To read the calendar through the shadow registers after Calendar
+ * initialization, calendar update or after wakeup from low power modes
+ * the software must first clear the RSF flag.
+ * The software must then wait until it is set again before reading
+ * the calendar, which means that the calendar registers have been
+ * correctly copied into the RTC_TR and RTC_DR shadow registers.
+ * @param hrtc RTC handle
+ * @retval HAL status
+ */
+HAL_StatusTypeDef HAL_RTC_WaitForSynchro(RTC_HandleTypeDef* hrtc)
+{
+ uint32_t tickstart;
+
+ /* Clear RSF flag */
+ hrtc->Instance->ISR &= (uint32_t)RTC_RSF_MASK;
+
+ tickstart = HAL_GetTick();
+
+ /* Wait the registers to be synchronised */
+ while((hrtc->Instance->ISR & RTC_ISR_RSF) == 0u)
+ {
+ if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+
+ return HAL_OK;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup RTC_Exported_Functions_Group5 Peripheral State functions
+ * @brief Peripheral State functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Peripheral State functions #####
+ ===============================================================================
+ [..]
+ This subsection provides functions allowing to
+ (+) Get RTC state
+
+@endverbatim
+ * @{
+ */
+/**
+ * @brief Return the RTC handle state.
+ * @param hrtc RTC handle
+ * @retval HAL state
+ */
+HAL_RTCStateTypeDef HAL_RTC_GetState(RTC_HandleTypeDef* hrtc)
+{
+ /* Return RTC handle state */
+ return hrtc->State;
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/** @defgroup RTC_Private_Functions RTC Private functions
+ * @{
+ */
+/**
+ * @brief Enter the RTC Initialization mode.
+ * @note The RTC Initialization mode is write protected, use the
+ * __HAL_RTC_WRITEPROTECTION_DISABLE() before calling this function.
+ * @param hrtc RTC handle
+ * @retval HAL status
+ */
+HAL_StatusTypeDef RTC_EnterInitMode(RTC_HandleTypeDef* hrtc)
+{
+ uint32_t tickstart ;
+
+ /* Check if the Initialization mode is set */
+ if((hrtc->Instance->ISR & RTC_ISR_INITF) == 0u)
+ {
+ /* Set the Initialization mode */
+ hrtc->Instance->ISR = (uint32_t)RTC_INIT_MASK;
+
+ tickstart = HAL_GetTick();
+ /* Wait till RTC is in INIT state and if Time out is reached exit */
+ while((hrtc->Instance->ISR & RTC_ISR_INITF) == 0u)
+ {
+ if((HAL_GetTick() - tickstart ) > RTC_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+
+ return HAL_OK;
+}
+
+
+/**
+ * @brief Convert a 2 digit decimal to BCD format.
+ * @param Value Byte to be converted
+ * @retval Converted byte
+ */
+uint8_t RTC_ByteToBcd2(uint8_t Value)
+{
+ uint32_t bcdhigh = 0u;
+ uint8_t Param = Value;
+
+ while(Param >= 10u)
+ {
+ bcdhigh++;
+ Param -= 10u;
+ }
+
+ return ((uint8_t)(bcdhigh << 4u) | Param);
+}
+
+/**
+ * @brief Convert from 2 digit BCD to Binary.
+ * @param Value: BCD value to be converted
+ * @retval Converted word
+ */
+uint8_t RTC_Bcd2ToByte(uint8_t Value)
+{
+ uint8_t tmp;
+ tmp = ((Value & 0xF0u) >> 4u) * 10u;
+ return (tmp + (Value & 0x0Fu));
+}
+
+/**
+ * @}
+ */
+
+#endif /* HAL_RTC_MODULE_ENABLED */
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
