Diff: targets/TARGET_STM/TARGET_STM32F0/device/stm32f0xx_hal_uart_ex.c

Revision:

180:96ed750bd169

Parent:

156:95d6b41a828b

--- a/targets/TARGET_STM/TARGET_STM32F0/device/stm32f0xx_hal_uart_ex.c	Thu Dec 07 14:01:42 2017 +0000
+++ b/targets/TARGET_STM/TARGET_STM32F0/device/stm32f0xx_hal_uart_ex.c	Wed Jan 17 15:23:54 2018 +0000
@@ -2,8 +2,6 @@
   ******************************************************************************
   * @file    stm32f0xx_hal_uart_ex.c
   * @author  MCD Application Team
-  * @version V1.5.0
-  * @date    04-November-2016
   * @brief   Extended UART HAL module driver.
   *          This file provides firmware functions to manage the following extended
   *          functionalities of the Universal Asynchronous Receiver Transmitter Peripheral (UART).
@@ -165,16 +163,16 @@
 /**
   * @brief Initialize the RS485 Driver enable feature according to the specified
   *         parameters in the UART_InitTypeDef and creates the associated handle.
-  * @param huart: UART handle.
-  * @param Polarity: select the driver enable polarity.
+  * @param huart UART handle.
+  * @param Polarity select the driver enable polarity.
   *        This parameter can be one of the following values:
   *          @arg @ref UART_DE_POLARITY_HIGH DE signal is active high
   *          @arg @ref UART_DE_POLARITY_LOW  DE signal is active low
-  * @param AssertionTime: Driver Enable assertion time:
+  * @param AssertionTime Driver Enable assertion time:
   *                         5-bit value defining the time between the activation of the DE (Driver Enable)
   *                         signal and the beginning of the start bit. It is expressed in sample time
   *                         units (1/8 or 1/16 bit time, depending on the oversampling rate)
-  * @param DeassertionTime: Driver Enable deassertion time:
+  * @param DeassertionTime Driver Enable deassertion time:
   *                         5-bit value defining the time between the end of the last stop bit, in a
   *                         transmitted message, and the de-activation of the DE (Driver Enable) signal.
   *                         It is expressed in sample time units (1/8 or 1/16 bit time, depending on the
@@ -249,8 +247,8 @@
 /**
   * @brief Initialize the LIN mode according to the specified
   *        parameters in the UART_InitTypeDef and creates the associated handle .
-  * @param huart: UART handle.
-  * @param BreakDetectLength: specifies the LIN break detection length.
+  * @param huart UART handle.
+  * @param BreakDetectLength specifies the LIN break detection length.
   *        This parameter can be one of the following values:
   *          @arg @ref UART_LINBREAKDETECTLENGTH_10B 10-bit break detection
   *          @arg @ref UART_LINBREAKDETECTLENGTH_11B 11-bit break detection
@@ -349,7 +347,7 @@
 #if !defined(STM32F030x6) && !defined(STM32F030x8)&& !defined(STM32F070xB)&& !defined(STM32F070x6)&& !defined(STM32F030xC)
 /**
   * @brief  UART wakeup from Stop mode callback.
-  * @param  huart: UART handle.
+  * @param  huart UART handle.
   * @retval None
   */
 __weak void HAL_UARTEx_WakeupCallback(UART_HandleTypeDef *huart)
@@ -393,8 +391,8 @@
 #if !defined(STM32F030x6) && !defined(STM32F030x8)&& !defined(STM32F070xB)&& !defined(STM32F070x6)&& !defined(STM32F030xC)
 /**
   * @brief Set Wakeup from Stop mode interrupt flag selection.
-  * @param huart: UART handle.
-  * @param WakeUpSelection: address match, Start Bit detection or RXNE bit status.
+  * @param huart UART handle.
+  * @param WakeUpSelection address match, Start Bit detection or RXNE bit status.
   * This parameter can be one of the following values:
   *      @arg @ref UART_WAKEUP_ON_ADDRESS
   *      @arg @ref UART_WAKEUP_ON_STARTBIT
@@ -454,7 +452,7 @@
 /**
   * @brief Enable UART Stop Mode.
   * @note  The UART is able to wake up the MCU from Stop 1 mode as long as UART clock is HSI or LSE.
-  * @param huart: UART handle.
+  * @param huart UART handle.
   * @retval HAL status
   */
 HAL_StatusTypeDef HAL_UARTEx_EnableStopMode(UART_HandleTypeDef *huart)
@@ -480,7 +478,7 @@
 
 /**
   * @brief Disable UART Stop Mode.
-  * @param huart: UART handle.
+  * @param huart UART handle.
   * @retval HAL status
   */
 HAL_StatusTypeDef HAL_UARTEx_DisableStopMode(UART_HandleTypeDef *huart)
@@ -512,8 +510,8 @@
   *        long).
   * @note  Addresses detection lengths are: 6-bit address detection in 7-bit data mode, 
   *        7-bit address detection in 8-bit data mode, 8-bit address detection in 9-bit data mode.
-  * @param huart: UART handle.
-  * @param AddressLength: this parameter can be one of the following values:
+  * @param huart UART handle.
+  * @param AddressLength this parameter can be one of the following values:
   *          @arg @ref UART_ADDRESS_DETECT_4B 4-bit long address
   *          @arg @ref UART_ADDRESS_DETECT_7B 6-, 7- or 8-bit long address
   * @retval HAL status
@@ -548,7 +546,7 @@
 #if !defined(STM32F030x6) && !defined(STM32F030x8)&& !defined(STM32F070xB)&& !defined(STM32F070x6)&& !defined(STM32F030xC)
 /**
   * @brief  Transmit break characters.
-  * @param  huart: UART handle.
+  * @param  huart UART handle.
   * @retval HAL status
   */
 HAL_StatusTypeDef HAL_LIN_SendBreak(UART_HandleTypeDef *huart)
@@ -588,8 +586,8 @@
 #if !defined(STM32F030x6) && !defined(STM32F030x8)&& !defined(STM32F070xB)&& !defined(STM32F070x6)&& !defined(STM32F030xC)
 /**
   * @brief Initialize the UART wake-up from stop mode parameters when triggered by address detection.
-  * @param huart: UART handle.
-  * @param WakeUpSelection: UART wake up from stop mode parameters.
+  * @param huart UART handle.
+  * @param WakeUpSelection UART wake up from stop mode parameters.
   * @retval None
   */
 static void UARTEx_Wakeup_AddressConfig(UART_HandleTypeDef *huart, UART_WakeUpTypeDef WakeUpSelection)