mbed official
mbed library sources. Supersedes mbed-src.
Dependents: Nucleo_Hello_Encoder BLE_iBeaconScan AM1805_DEMO DISCO-F429ZI_ExportTemplate1 ... more
Diff: targets/TARGET_STM/TARGET_STM32F0/device/stm32f0xx_hal_uart.h
- Revision:
- 149:156823d33999
- Parent:
- 144:ef7eb2e8f9f7
- Child:
- 156:95d6b41a828b
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/TARGET_STM/TARGET_STM32F0/device/stm32f0xx_hal_uart.h Fri Oct 28 11:17:30 2016 +0100
@@ -0,0 +1,1268 @@
+/**
+ ******************************************************************************
+ * @file stm32f0xx_hal_uart.h
+ * @author MCD Application Team
+ * @version V1.4.0
+ * @date 27-May-2016
+ * @brief Header file of UART HAL module.
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F0xx_HAL_UART_H
+#define __STM32F0xx_HAL_UART_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal_def.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+ * @{
+ */
+
+/** @addtogroup UART
+ * @{
+ */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup UART_Exported_Types UART Exported Types
+ * @{
+ */
+
+/**
+ * @brief UART Init Structure definition
+ */
+typedef struct
+{
+ uint32_t BaudRate; /*!< This member configures the UART communication baud rate.
+ The baud rate register is computed using the following formula:
+ - If oversampling is 16 or in LIN mode (LIN mode not available on F030xx devices),
+ Baud Rate Register = ((PCLKx) / ((huart->Init.BaudRate)))
+ - If oversampling is 8,
+ Baud Rate Register[15:4] = ((2 * PCLKx) / ((huart->Init.BaudRate)))[15:4]
+ Baud Rate Register[3] = 0
+ Baud Rate Register[2:0] = (((2 * PCLKx) / ((huart->Init.BaudRate)))[3:0]) >> 1 */
+
+ uint32_t WordLength; /*!< Specifies the number of data bits transmitted or received in a frame.
+ This parameter can be a value of @ref UARTEx_Word_Length */
+
+ uint32_t StopBits; /*!< Specifies the number of stop bits transmitted.
+ This parameter can be a value of @ref UART_Stop_Bits */
+
+ uint32_t Parity; /*!< Specifies the parity mode.
+ This parameter can be a value of @ref UART_Parity
+ @note When parity is enabled, the computed parity is inserted
+ at the MSB position of the transmitted data (9th bit when
+ the word length is set to 9 data bits; 8th bit when the
+ word length is set to 8 data bits). */
+
+ uint32_t Mode; /*!< Specifies whether the Receive or Transmit mode is enabled or disabled.
+ This parameter can be a value of @ref UART_Mode */
+
+ uint32_t HwFlowCtl; /*!< Specifies whether the hardware flow control mode is enabled
+ or disabled.
+ This parameter can be a value of @ref UART_Hardware_Flow_Control */
+
+ uint32_t OverSampling; /*!< Specifies whether the Over sampling 8 is enabled or disabled, to achieve higher speed (up to f_PCLK/8).
+ This parameter can be a value of @ref UART_Over_Sampling */
+
+ uint32_t OneBitSampling; /*!< Specifies whether a single sample or three samples' majority vote is selected.
+ Selecting the single sample method increases the receiver tolerance to clock
+ deviations. This parameter can be a value of @ref UART_OneBit_Sampling. */
+}UART_InitTypeDef;
+
+/**
+ * @brief UART Advanced Features initalization structure definition
+ */
+typedef struct
+{
+ uint32_t AdvFeatureInit; /*!< Specifies which advanced UART features is initialized. Several
+ Advanced Features may be initialized at the same time .
+ This parameter can be a value of @ref UART_Advanced_Features_Initialization_Type */
+
+ uint32_t TxPinLevelInvert; /*!< Specifies whether the TX pin active level is inverted.
+ This parameter can be a value of @ref UART_Tx_Inv */
+
+ uint32_t RxPinLevelInvert; /*!< Specifies whether the RX pin active level is inverted.
+ This parameter can be a value of @ref UART_Rx_Inv */
+
+ uint32_t DataInvert; /*!< Specifies whether data are inverted (positive/direct logic
+ vs negative/inverted logic).
+ This parameter can be a value of @ref UART_Data_Inv */
+
+ uint32_t Swap; /*!< Specifies whether TX and RX pins are swapped.
+ This parameter can be a value of @ref UART_Rx_Tx_Swap */
+
+ uint32_t OverrunDisable; /*!< Specifies whether the reception overrun detection is disabled.
+ This parameter can be a value of @ref UART_Overrun_Disable */
+
+ uint32_t DMADisableonRxError; /*!< Specifies whether the DMA is disabled in case of reception error.
+ This parameter can be a value of @ref UART_DMA_Disable_on_Rx_Error */
+
+ uint32_t AutoBaudRateEnable; /*!< Specifies whether auto Baud rate detection is enabled.
+ This parameter can be a value of @ref UART_AutoBaudRate_Enable */
+
+ uint32_t AutoBaudRateMode; /*!< If auto Baud rate detection is enabled, specifies how the rate
+ detection is carried out.
+ This parameter can be a value of @ref UARTEx_AutoBaud_Rate_Mode */
+
+ uint32_t MSBFirst; /*!< Specifies whether MSB is sent first on UART line.
+ This parameter can be a value of @ref UART_MSB_First */
+} UART_AdvFeatureInitTypeDef;
+
+
+
+/**
+ * @brief HAL UART State structures definition
+ * @note HAL UART State value is a combination of 2 different substates: gState and RxState.
+ * - gState contains UART state information related to global Handle management
+ * and also information related to Tx operations.
+ * gState value coding follow below described bitmap :
+ * b7-b6 Error information
+ * 00 : No Error
+ * 01 : (Not Used)
+ * 10 : Timeout
+ * 11 : Error
+ * b5 IP initilisation status
+ * 0 : Reset (IP not initialized)
+ * 1 : Init done (IP not initialized. HAL UART Init function already called)
+ * b4-b3 (not used)
+ * xx : Should be set to 00
+ * b2 Intrinsic process state
+ * 0 : Ready
+ * 1 : Busy (IP busy with some configuration or internal operations)
+ * b1 (not used)
+ * x : Should be set to 0
+ * b0 Tx state
+ * 0 : Ready (no Tx operation ongoing)
+ * 1 : Busy (Tx operation ongoing)
+ * - RxState contains information related to Rx operations.
+ * RxState value coding follow below described bitmap :
+ * b7-b6 (not used)
+ * xx : Should be set to 00
+ * b5 IP initilisation status
+ * 0 : Reset (IP not initialized)
+ * 1 : Init done (IP not initialized)
+ * b4-b2 (not used)
+ * xxx : Should be set to 000
+ * b1 Rx state
+ * 0 : Ready (no Rx operation ongoing)
+ * 1 : Busy (Rx operation ongoing)
+ * b0 (not used)
+ * x : Should be set to 0.
+ */
+typedef enum
+{
+ HAL_UART_STATE_RESET = 0x00U, /*!< Peripheral is not initialized
+ Value is allowed for gState and RxState */
+ HAL_UART_STATE_READY = 0x20U, /*!< Peripheral Initialized and ready for use
+ Value is allowed for gState and RxState */
+ HAL_UART_STATE_BUSY = 0x24U, /*!< an internal process is ongoing
+ Value is allowed for gState only */
+ HAL_UART_STATE_BUSY_TX = 0x21U, /*!< Data Transmission process is ongoing
+ Value is allowed for gState only */
+ HAL_UART_STATE_BUSY_RX = 0x22U, /*!< Data Reception process is ongoing
+ Value is allowed for RxState only */
+ HAL_UART_STATE_BUSY_TX_RX = 0x23U, /*!< Data Transmission and Reception process is ongoing
+ Not to be used for neither gState nor RxState.
+ Value is result of combination (Or) between gState and RxState values */
+ HAL_UART_STATE_TIMEOUT = 0xA0U, /*!< Timeout state
+ Value is allowed for gState only */
+ HAL_UART_STATE_ERROR = 0xE0U /*!< Error
+ Value is allowed for gState only */
+}HAL_UART_StateTypeDef;
+
+/**
+ * @brief UART clock sources definition
+ */
+typedef enum
+{
+ UART_CLOCKSOURCE_PCLK1 = 0x00, /*!< PCLK1 clock source */
+ UART_CLOCKSOURCE_HSI = 0x02, /*!< HSI clock source */
+ UART_CLOCKSOURCE_SYSCLK = 0x04, /*!< SYSCLK clock source */
+ UART_CLOCKSOURCE_LSE = 0x08, /*!< LSE clock source */
+ UART_CLOCKSOURCE_UNDEFINED = 0x10 /*!< Undefined clock source */
+}UART_ClockSourceTypeDef;
+
+/**
+ * @brief UART handle Structure definition
+ */
+typedef struct
+{
+ USART_TypeDef *Instance; /*!< UART registers base address */
+
+ UART_InitTypeDef Init; /*!< UART communication parameters */
+
+ UART_AdvFeatureInitTypeDef AdvancedInit; /*!< UART Advanced Features initialization parameters */
+
+ uint8_t *pTxBuffPtr; /*!< Pointer to UART Tx transfer Buffer */
+
+ uint16_t TxXferSize; /*!< UART Tx Transfer size */
+
+ uint16_t TxXferCount; /*!< UART Tx Transfer Counter */
+
+ uint8_t *pRxBuffPtr; /*!< Pointer to UART Rx transfer Buffer */
+
+ uint16_t RxXferSize; /*!< UART Rx Transfer size */
+
+ uint16_t RxXferCount; /*!< UART Rx Transfer Counter */
+
+ uint16_t Mask; /*!< UART Rx RDR register mask */
+
+ DMA_HandleTypeDef *hdmatx; /*!< UART Tx DMA Handle parameters */
+
+ DMA_HandleTypeDef *hdmarx; /*!< UART Rx DMA Handle parameters */
+
+ HAL_LockTypeDef Lock; /*!< Locking object */
+
+ __IO HAL_UART_StateTypeDef gState; /*!< UART state information related to global Handle management
+ and also related to Tx operations.
+ This parameter can be a value of @ref HAL_UART_StateTypeDef */
+
+ __IO HAL_UART_StateTypeDef RxState; /*!< UART state information related to Rx operations.
+ This parameter can be a value of @ref HAL_UART_StateTypeDef */
+
+ __IO uint32_t ErrorCode; /*!< UART Error code */
+
+}UART_HandleTypeDef;
+
+/**
+ * @}
+ */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup UART_Exported_Constants UART Exported Constants
+ * @{
+ */
+
+/** @defgroup UART_Error UART Error
+ * @{
+ */
+#define HAL_UART_ERROR_NONE ((uint32_t)0x00000000) /*!< No error */
+#define HAL_UART_ERROR_PE ((uint32_t)0x00000001) /*!< Parity error */
+#define HAL_UART_ERROR_NE ((uint32_t)0x00000002) /*!< Noise error */
+#define HAL_UART_ERROR_FE ((uint32_t)0x00000004) /*!< frame error */
+#define HAL_UART_ERROR_ORE ((uint32_t)0x00000008) /*!< Overrun error */
+#define HAL_UART_ERROR_DMA ((uint32_t)0x00000010) /*!< DMA transfer error */
+/**
+ * @}
+ */
+
+/** @defgroup UART_Stop_Bits UART Number of Stop Bits
+ * @{
+ */
+#ifdef USART_SMARTCARD_SUPPORT
+#define UART_STOPBITS_0_5 USART_CR2_STOP_0 /*!< UART frame with 0.5 stop bit */
+#define UART_STOPBITS_1 ((uint32_t)0x00000000) /*!< UART frame with 1 stop bit */
+#define UART_STOPBITS_1_5 ((uint32_t)(USART_CR2_STOP_0 | USART_CR2_STOP_1)) /*!< UART frame with 1.5 stop bits */
+#define UART_STOPBITS_2 ((uint32_t)USART_CR2_STOP_1) /*!< UART frame with 2 stop bits */
+#else
+#define UART_STOPBITS_1 ((uint32_t)0x00000000) /*!< UART frame with 1 stop bit */
+#define UART_STOPBITS_2 ((uint32_t)USART_CR2_STOP_1) /*!< UART frame with 2 stop bits */
+#endif
+/**
+ * @}
+ */
+
+/** @defgroup UART_Parity UART Parity
+ * @{
+ */
+#define UART_PARITY_NONE ((uint32_t)0x00000000) /*!< No parity */
+#define UART_PARITY_EVEN ((uint32_t)USART_CR1_PCE) /*!< Even parity */
+#define UART_PARITY_ODD ((uint32_t)(USART_CR1_PCE | USART_CR1_PS)) /*!< Odd parity */
+/**
+ * @}
+ */
+
+/** @defgroup UART_Hardware_Flow_Control UART Hardware Flow Control
+ * @{
+ */
+#define UART_HWCONTROL_NONE ((uint32_t)0x00000000) /*!< No hardware control */
+#define UART_HWCONTROL_RTS ((uint32_t)USART_CR3_RTSE) /*!< Request To Send */
+#define UART_HWCONTROL_CTS ((uint32_t)USART_CR3_CTSE) /*!< Clear To Send */
+#define UART_HWCONTROL_RTS_CTS ((uint32_t)(USART_CR3_RTSE | USART_CR3_CTSE)) /*!< Request and Clear To Send */
+/**
+ * @}
+ */
+
+/** @defgroup UART_Mode UART Transfer Mode
+ * @{
+ */
+#define UART_MODE_RX ((uint32_t)USART_CR1_RE) /*!< RX mode */
+#define UART_MODE_TX ((uint32_t)USART_CR1_TE) /*!< TX mode */
+#define UART_MODE_TX_RX ((uint32_t)(USART_CR1_TE |USART_CR1_RE)) /*!< RX and TX mode */
+/**
+ * @}
+ */
+
+/** @defgroup UART_State UART State
+ * @{
+ */
+#define UART_STATE_DISABLE ((uint32_t)0x00000000) /*!< UART disabled */
+#define UART_STATE_ENABLE ((uint32_t)USART_CR1_UE) /*!< UART enabled */
+/**
+ * @}
+ */
+
+/** @defgroup UART_Over_Sampling UART Over Sampling
+ * @{
+ */
+#define UART_OVERSAMPLING_16 ((uint32_t)0x00000000) /*!< Oversampling by 16 */
+#define UART_OVERSAMPLING_8 ((uint32_t)USART_CR1_OVER8) /*!< Oversampling by 8 */
+/**
+ * @}
+ */
+
+/** @defgroup UART_OneBit_Sampling UART One Bit Sampling Method
+ * @{
+ */
+#define UART_ONE_BIT_SAMPLE_DISABLE ((uint32_t)0x00000000) /*!< One-bit sampling disable */
+#define UART_ONE_BIT_SAMPLE_ENABLE ((uint32_t)USART_CR3_ONEBIT) /*!< One-bit sampling enable */
+/**
+ * @}
+ */
+
+/** @defgroup UART_Receiver_TimeOut UART Receiver TimeOut
+ * @{
+ */
+#define UART_RECEIVER_TIMEOUT_DISABLE ((uint32_t)0x00000000) /*!< UART receiver timeout disable */
+#define UART_RECEIVER_TIMEOUT_ENABLE ((uint32_t)USART_CR2_RTOEN) /*!< UART receiver timeout enable */
+/**
+ * @}
+ */
+
+/** @defgroup UART_DMA_Tx UART DMA Tx
+ * @{
+ */
+#define UART_DMA_TX_DISABLE ((uint32_t)0x00000000) /*!< UART DMA TX disabled */
+#define UART_DMA_TX_ENABLE ((uint32_t)USART_CR3_DMAT) /*!< UART DMA TX enabled */
+/**
+ * @}
+ */
+
+/** @defgroup UART_DMA_Rx UART DMA Rx
+ * @{
+ */
+#define UART_DMA_RX_DISABLE ((uint32_t)0x00000000) /*!< UART DMA RX disabled */
+#define UART_DMA_RX_ENABLE ((uint32_t)USART_CR3_DMAR) /*!< UART DMA RX enabled */
+/**
+ * @}
+ */
+
+/** @defgroup UART_Half_Duplex_Selection UART Half Duplex Selection
+ * @{
+ */
+#define UART_HALF_DUPLEX_DISABLE ((uint32_t)0x00000000) /*!< UART half-duplex disabled */
+#define UART_HALF_DUPLEX_ENABLE ((uint32_t)USART_CR3_HDSEL) /*!< UART half-duplex enabled */
+/**
+ * @}
+ */
+
+/** @defgroup UART_WakeUp_Address_Length UART WakeUp Address Length
+ * @{
+ */
+#define UART_ADDRESS_DETECT_4B ((uint32_t)0x00000000) /*!< 4-bit long wake-up address */
+#define UART_ADDRESS_DETECT_7B ((uint32_t)USART_CR2_ADDM7) /*!< 7-bit long wake-up address */
+/**
+ * @}
+ */
+
+/** @defgroup UART_WakeUp_Methods UART WakeUp Methods
+ * @{
+ */
+#define UART_WAKEUPMETHOD_IDLELINE ((uint32_t)0x00000000) /*!< UART wake-up on idle line */
+#define UART_WAKEUPMETHOD_ADDRESSMARK ((uint32_t)USART_CR1_WAKE) /*!< UART wake-up on address mark */
+/**
+ * @}
+ */
+
+/** @defgroup UART_IT UART IT
+ * Elements values convention: 000000000XXYYYYYb
+ * - YYYYY : Interrupt source position in the XX register (5bits)
+ * - XX : Interrupt source register (2bits)
+ * - 01: CR1 register
+ * - 10: CR2 register
+ * - 11: CR3 register
+ * @{
+ */
+#define UART_IT_ERR ((uint16_t)0x0060)
+
+/** Elements values convention: 0000ZZZZ00000000b
+ * - ZZZZ : Flag position in the ISR register(4bits)
+ */
+#define UART_IT_ORE ((uint16_t)0x0300)
+#define UART_IT_NE ((uint16_t)0x0200)
+#define UART_IT_FE ((uint16_t)0x0100)
+/**
+ * @}
+ */
+
+/** @defgroup UART_Advanced_Features_Initialization_Type UART Advanced Feature Initialization Type
+ * @{
+ */
+#define UART_ADVFEATURE_NO_INIT ((uint32_t)0x00000000) /*!< No advanced feature initialization */
+#define UART_ADVFEATURE_TXINVERT_INIT ((uint32_t)0x00000001) /*!< TX pin active level inversion */
+#define UART_ADVFEATURE_RXINVERT_INIT ((uint32_t)0x00000002) /*!< RX pin active level inversion */
+#define UART_ADVFEATURE_DATAINVERT_INIT ((uint32_t)0x00000004) /*!< Binary data inversion */
+#define UART_ADVFEATURE_SWAP_INIT ((uint32_t)0x00000008) /*!< TX/RX pins swap */
+#define UART_ADVFEATURE_RXOVERRUNDISABLE_INIT ((uint32_t)0x00000010) /*!< RX overrun disable */
+#define UART_ADVFEATURE_DMADISABLEONERROR_INIT ((uint32_t)0x00000020) /*!< DMA disable on Reception Error */
+#define UART_ADVFEATURE_AUTOBAUDRATE_INIT ((uint32_t)0x00000040) /*!< Auto Baud rate detection initialization */
+#define UART_ADVFEATURE_MSBFIRST_INIT ((uint32_t)0x00000080) /*!< Most significant bit sent/received first */
+/**
+ * @}
+ */
+
+/** @defgroup UART_Tx_Inv UART Advanced Feature TX Pin Active Level Inversion
+ * @{
+ */
+#define UART_ADVFEATURE_TXINV_DISABLE ((uint32_t)0x00000000) /*!< TX pin active level inversion disable */
+#define UART_ADVFEATURE_TXINV_ENABLE ((uint32_t)USART_CR2_TXINV) /*!< TX pin active level inversion enable */
+/**
+ * @}
+ */
+
+/** @defgroup UART_Rx_Inv UART Advanced Feature RX Pin Active Level Inversion
+ * @{
+ */
+#define UART_ADVFEATURE_RXINV_DISABLE ((uint32_t)0x00000000) /*!< RX pin active level inversion disable */
+#define UART_ADVFEATURE_RXINV_ENABLE ((uint32_t)USART_CR2_RXINV) /*!< RX pin active level inversion enable */
+/**
+ * @}
+ */
+
+/** @defgroup UART_Data_Inv UART Advanced Feature Binary Data Inversion
+ * @{
+ */
+#define UART_ADVFEATURE_DATAINV_DISABLE ((uint32_t)0x00000000) /*!< Binary data inversion disable */
+#define UART_ADVFEATURE_DATAINV_ENABLE ((uint32_t)USART_CR2_DATAINV) /*!< Binary data inversion enable */
+/**
+ * @}
+ */
+
+/** @defgroup UART_Rx_Tx_Swap UART Advanced Feature RX TX Pins Swap
+ * @{
+ */
+#define UART_ADVFEATURE_SWAP_DISABLE ((uint32_t)0x00000000) /*!< TX/RX pins swap disable */
+#define UART_ADVFEATURE_SWAP_ENABLE ((uint32_t)USART_CR2_SWAP) /*!< TX/RX pins swap enable */
+/**
+ * @}
+ */
+
+/** @defgroup UART_Overrun_Disable UART Advanced Feature Overrun Disable
+ * @{
+ */
+#define UART_ADVFEATURE_OVERRUN_ENABLE ((uint32_t)0x00000000) /*!< RX overrun enable */
+#define UART_ADVFEATURE_OVERRUN_DISABLE ((uint32_t)USART_CR3_OVRDIS) /*!< RX overrun disable */
+/**
+ * @}
+ */
+
+/** @defgroup UART_AutoBaudRate_Enable UART Advanced Feature Auto BaudRate Enable
+ * @{
+ */
+#define UART_ADVFEATURE_AUTOBAUDRATE_DISABLE ((uint32_t)0x00000000) /*!< RX Auto Baud rate detection enable */
+#define UART_ADVFEATURE_AUTOBAUDRATE_ENABLE ((uint32_t)USART_CR2_ABREN) /*!< RX Auto Baud rate detection disable */
+/**
+ * @}
+ */
+
+/** @defgroup UART_DMA_Disable_on_Rx_Error UART Advanced Feature DMA Disable On Rx Error
+ * @{
+ */
+#define UART_ADVFEATURE_DMA_ENABLEONRXERROR ((uint32_t)0x00000000) /*!< DMA enable on Reception Error */
+#define UART_ADVFEATURE_DMA_DISABLEONRXERROR ((uint32_t)USART_CR3_DDRE) /*!< DMA disable on Reception Error */
+/**
+ * @}
+ */
+
+/** @defgroup UART_MSB_First UART Advanced Feature MSB First
+ * @{
+ */
+#define UART_ADVFEATURE_MSBFIRST_DISABLE ((uint32_t)0x00000000) /*!< Most significant bit sent/received first disable */
+#define UART_ADVFEATURE_MSBFIRST_ENABLE ((uint32_t)USART_CR2_MSBFIRST) /*!< Most significant bit sent/received first enable */
+/**
+ * @}
+ */
+
+/** @defgroup UART_Mute_Mode UART Advanced Feature Mute Mode Enable
+ * @{
+ */
+#define UART_ADVFEATURE_MUTEMODE_DISABLE ((uint32_t)0x00000000) /*!< UART mute mode disable */
+#define UART_ADVFEATURE_MUTEMODE_ENABLE ((uint32_t)USART_CR1_MME) /*!< UART mute mode enable */
+/**
+ * @}
+ */
+
+/** @defgroup UART_CR2_ADDRESS_LSB_POS UART Address-matching LSB Position In CR2 Register
+ * @{
+ */
+#define UART_CR2_ADDRESS_LSB_POS ((uint32_t) 24)
+/**
+ * @}
+ */
+
+/** @defgroup UART_DriverEnable_Polarity UART DriverEnable Polarity
+ * @{
+ */
+#define UART_DE_POLARITY_HIGH ((uint32_t)0x00000000) /*!< Driver enable signal is active high */
+#define UART_DE_POLARITY_LOW ((uint32_t)USART_CR3_DEP) /*!< Driver enable signal is active low */
+/**
+ * @}
+ */
+
+/** @defgroup UART_CR1_DEAT_ADDRESS_LSB_POS UART Driver Enable Assertion Time LSB Position In CR1 Register
+ * @{
+ */
+#define UART_CR1_DEAT_ADDRESS_LSB_POS ((uint32_t) 21)
+/**
+ * @}
+ */
+
+/** @defgroup UART_CR1_DEDT_ADDRESS_LSB_POS UART Driver Enable DeAssertion Time LSB Position In CR1 Register
+ * @{
+ */
+#define UART_CR1_DEDT_ADDRESS_LSB_POS ((uint32_t) 16)
+/**
+ * @}
+ */
+
+/** @defgroup UART_Interruption_Mask UART Interruptions Flag Mask
+ * @{
+ */
+#define UART_IT_MASK ((uint32_t)0x001F)
+/**
+ * @}
+ */
+
+/** @defgroup UART_TimeOut_Value UART polling-based communications time-out value
+ * @{
+ */
+#define HAL_UART_TIMEOUT_VALUE 0x1FFFFFF
+/**
+ * @}
+ */
+
+
+/**
+ * @}
+ */
+
+/* Exported macros -----------------------------------------------------------*/
+/** @defgroup UART_Exported_Macros UART Exported Macros
+ * @{
+ */
+
+/** @brief Reset UART handle states.
+ * @param __HANDLE__: UART handle.
+ * @retval None
+ */
+#define __HAL_UART_RESET_HANDLE_STATE(__HANDLE__) do{ \
+ (__HANDLE__)->gState = HAL_UART_STATE_RESET; \
+ (__HANDLE__)->RxState = HAL_UART_STATE_RESET; \
+ } while(0)
+
+/** @brief Clear the specified UART pending flag.
+ * @param __HANDLE__: specifies the UART Handle.
+ * @param __FLAG__: specifies the flag to check.
+ * This parameter can be any combination of the following values:
+ * @arg UART_CLEAR_PEF, Parity Error Clear Flag
+ * @arg UART_CLEAR_FEF, Framing Error Clear Flag
+ * @arg UART_CLEAR_NEF, Noise detected Clear Flag
+ * @arg UART_CLEAR_OREF, OverRun Error Clear Flag
+ * @arg UART_CLEAR_IDLEF, IDLE line detected Clear Flag
+ * @arg UART_CLEAR_TCF, Transmission Complete Clear Flag
+ * @arg UART_CLEAR_LBDF, LIN Break Detection Clear Flag (not available on all devices)
+ * @arg UART_CLEAR_CTSF, CTS Interrupt Clear Flag
+ * @arg UART_CLEAR_RTOF, Receiver Time Out Clear Flag
+ * @arg UART_CLEAR_EOBF, End Of Block Clear Flag (not available on all devices)
+ * @arg UART_CLEAR_CMF, Character Match Clear Flag
+ * @arg UART_CLEAR_WUF, Wake Up from stop mode Clear Flag (not available on all devices)
+ * @retval None
+ */
+#define __HAL_UART_CLEAR_FLAG(__HANDLE__, __FLAG__) ((__HANDLE__)->Instance->ICR = (__FLAG__))
+
+/** @brief Clear the UART PE pending flag.
+ * @param __HANDLE__: specifies the UART Handle.
+ * @retval None
+ */
+#define __HAL_UART_CLEAR_PEFLAG(__HANDLE__) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_PEF)
+
+/** @brief Clear the UART FE pending flag.
+ * @param __HANDLE__: specifies the UART Handle.
+ * @retval None
+ */
+#define __HAL_UART_CLEAR_FEFLAG(__HANDLE__) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_FEF)
+
+/** @brief Clear the UART NE pending flag.
+ * @param __HANDLE__: specifies the UART Handle.
+ * @retval None
+ */
+#define __HAL_UART_CLEAR_NEFLAG(__HANDLE__) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_NEF)
+
+/** @brief Clear the UART ORE pending flag.
+ * @param __HANDLE__: specifies the UART Handle.
+ * @retval None
+ */
+#define __HAL_UART_CLEAR_OREFLAG(__HANDLE__) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_OREF)
+
+/** @brief Clear the UART IDLE pending flag.
+ * @param __HANDLE__: specifies the UART Handle.
+ * @retval None
+ */
+#define __HAL_UART_CLEAR_IDLEFLAG(__HANDLE__) __HAL_UART_CLEAR_FLAG((__HANDLE__), UART_CLEAR_IDLEF)
+
+/** @brief Check whether the specified UART flag is set or not.
+ * @param __HANDLE__: specifies the UART Handle.
+ * This parameter can be UARTx where x: 1, 2, 3 or 4 to select the USART or
+ * UART peripheral (datasheet: up to four USART/UARTs)
+ * @param __FLAG__: specifies the flag to check.
+ * This parameter can be one of the following values:
+ * @arg UART_FLAG_REACK: Receive enable acknowledge flag
+ * @arg UART_FLAG_TEACK: Transmit enable acknowledge flag
+ * @arg UART_FLAG_WUF: Wake up from stop mode flag (not available on F030xx devices)
+ * @arg UART_FLAG_RWU: Receiver wake up flag (not available on F030xx devices)
+ * @arg UART_FLAG_SBKF: Send Break flag
+ * @arg UART_FLAG_CMF: Character match flag
+ * @arg UART_FLAG_BUSY: Busy flag
+ * @arg UART_FLAG_ABRF: Auto Baud rate detection flag
+ * @arg UART_FLAG_ABRE: Auto Baud rate detection error flag
+ * @arg UART_FLAG_EOBF: End of block flag (not available on F030xx devices)
+ * @arg UART_FLAG_RTOF: Receiver timeout flag
+ * @arg UART_FLAG_CTS: CTS Change flag
+ * @arg UART_FLAG_LBD: LIN Break detection flag (not available on F030xx devices)
+ * @arg UART_FLAG_TXE: Transmit data register empty flag
+ * @arg UART_FLAG_TC: Transmission Complete flag
+ * @arg UART_FLAG_RXNE: Receive data register not empty flag
+ * @arg UART_FLAG_IDLE: Idle Line detection flag
+ * @arg UART_FLAG_ORE: OverRun Error flag
+ * @arg UART_FLAG_NE: Noise Error flag
+ * @arg UART_FLAG_FE: Framing Error flag
+ * @arg UART_FLAG_PE: Parity Error flag
+ * @retval The new state of __FLAG__ (TRUE or FALSE).
+ */
+#define __HAL_UART_GET_FLAG(__HANDLE__, __FLAG__) (((__HANDLE__)->Instance->ISR & (__FLAG__)) == (__FLAG__))
+
+/** @brief Enable the specified UART interrupt.
+ * @param __HANDLE__: specifies the UART Handle.
+ * This parameter can be UARTx where x: 1, 2, 3 or 4 to select the USART or
+ * UART peripheral. (datasheet: up to four USART/UARTs)
+ * @param __INTERRUPT__: specifies the UART interrupt source to enable.
+ * This parameter can be one of the following values:
+ * @arg UART_IT_WUF: Wakeup from stop mode interrupt (not available on F030xx devices)
+ * @arg UART_IT_CM: Character match interrupt
+ * @arg UART_IT_CTS: CTS change interrupt
+ * @arg UART_IT_LBD: LIN Break detection interrupt (not available on F030xx devices)
+ * @arg UART_IT_TXE: Transmit Data Register empty interrupt
+ * @arg UART_IT_TC: Transmission complete interrupt
+ * @arg UART_IT_RXNE: Receive Data register not empty interrupt
+ * @arg UART_IT_IDLE: Idle line detection interrupt
+ * @arg UART_IT_PE: Parity Error interrupt
+ * @arg UART_IT_ERR: Error interrupt(Frame error, noise error, overrun error)
+ * @retval None
+ */
+#define __HAL_UART_ENABLE_IT(__HANDLE__, __INTERRUPT__) (((((uint8_t)(__INTERRUPT__)) >> 5U) == 1)? ((__HANDLE__)->Instance->CR1 |= (1U << ((__INTERRUPT__) & UART_IT_MASK))): \
+ ((((uint8_t)(__INTERRUPT__)) >> 5U) == 2)? ((__HANDLE__)->Instance->CR2 |= (1U << ((__INTERRUPT__) & UART_IT_MASK))): \
+ ((__HANDLE__)->Instance->CR3 |= (1U << ((__INTERRUPT__) & UART_IT_MASK))))
+
+
+/** @brief Disable the specified UART interrupt.
+ * @param __HANDLE__: specifies the UART Handle.
+ * This parameter can be UARTx where x: 1, 2, 3 or 4 to select the USART or
+ * UART peripheral. (datasheet: up to four USART/UARTs)
+ * @param __INTERRUPT__: specifies the UART interrupt source to disable.
+ * This parameter can be one of the following values:
+ * @arg UART_IT_WUF: Wakeup from stop mode interrupt (not available on F030xx devices)
+ * @arg UART_IT_CM: Character match interrupt
+ * @arg UART_IT_CTS: CTS change interrupt
+ * @arg UART_IT_LBD: LIN Break detection interrupt (not available on F030xx devices)
+ * @arg UART_IT_TXE: Transmit Data Register empty interrupt
+ * @arg UART_IT_TC: Transmission complete interrupt
+ * @arg UART_IT_RXNE: Receive Data register not empty interrupt
+ * @arg UART_IT_IDLE: Idle line detection interrupt
+ * @arg UART_IT_PE: Parity Error interrupt
+ * @arg UART_IT_ERR: Error interrupt (Frame error, noise error, overrun error)
+ * @retval None
+ */
+#define __HAL_UART_DISABLE_IT(__HANDLE__, __INTERRUPT__) (((((uint8_t)(__INTERRUPT__)) >> 5U) == 1)? ((__HANDLE__)->Instance->CR1 &= ~ (1U << ((__INTERRUPT__) & UART_IT_MASK))): \
+ ((((uint8_t)(__INTERRUPT__)) >> 5U) == 2)? ((__HANDLE__)->Instance->CR2 &= ~ (1U << ((__INTERRUPT__) & UART_IT_MASK))): \
+ ((__HANDLE__)->Instance->CR3 &= ~ (1U << ((__INTERRUPT__) & UART_IT_MASK))))
+
+/** @brief Check whether the specified UART interrupt has occurred or not.
+ * @param __HANDLE__: specifies the UART Handle.
+ * This parameter can be UARTx where x: 1, 2, 3 or 4 to select the USART or
+ * UART peripheral. (datasheet: up to four USART/UARTs)
+ * @param __IT__: specifies the UART interrupt to check.
+ * This parameter can be one of the following values:
+ * @arg UART_IT_WUF: Wakeup from stop mode interrupt (not available on F030xx devices)
+ * @arg UART_IT_CM: Character match interrupt
+ * @arg UART_IT_CTS: CTS change interrupt
+ * @arg UART_IT_LBD: LIN Break detection interrupt (not available on F030xx devices)
+ * @arg UART_IT_TXE: Transmit Data Register empty interrupt
+ * @arg UART_IT_TC: Transmission complete interrupt
+ * @arg UART_IT_RXNE: Receive Data register not empty interrupt
+ * @arg UART_IT_IDLE: Idle line detection interrupt
+ * @arg UART_IT_ORE: OverRun Error interrupt
+ * @arg UART_IT_NE: Noise Error interrupt
+ * @arg UART_IT_FE: Framing Error interrupt
+ * @arg UART_IT_PE: Parity Error interrupt
+ * @retval The new state of __IT__ (TRUE or FALSE).
+ */
+#define __HAL_UART_GET_IT(__HANDLE__, __IT__) ((__HANDLE__)->Instance->ISR & ((uint32_t)1 << ((__IT__)>> 0x08)))
+
+/** @brief Check whether the specified UART interrupt source is enabled or not.
+ * @param __HANDLE__: specifies the UART Handle.
+ * This parameter can be UARTx where x: 1, 2, 3 or 4 to select the USART or
+ * UART peripheral. (datasheet: up to four USART/UARTs)
+ * @param __IT__: specifies the UART interrupt source to check.
+ * This parameter can be one of the following values:
+ * @arg UART_IT_WUF: Wakeup from stop mode interrupt (not available on F030xx devices)
+ * @arg UART_IT_CM: Character match interrupt
+ * @arg UART_IT_CTS: CTS change interrupt
+ * @arg UART_IT_LBD: LIN Break detection interrupt (not available on F030xx devices)
+ * @arg UART_IT_TXE: Transmit Data Register empty interrupt
+ * @arg UART_IT_TC: Transmission complete interrupt
+ * @arg UART_IT_RXNE: Receive Data register not empty interrupt
+ * @arg UART_IT_IDLE: Idle line detection interrupt
+ * @arg UART_IT_ORE: OverRun Error interrupt
+ * @arg UART_IT_NE: Noise Error interrupt
+ * @arg UART_IT_FE: Framing Error interrupt
+ * @arg UART_IT_PE: Parity Error interrupt
+ * @retval The new state of __IT__ (TRUE or FALSE).
+ */
+#define __HAL_UART_GET_IT_SOURCE(__HANDLE__, __IT__) ((((((uint8_t)(__IT__)) >> 5U) == 1)? (__HANDLE__)->Instance->CR1:(((((uint8_t)(__IT__)) >> 5U) == 2)? \
+ (__HANDLE__)->Instance->CR2 : (__HANDLE__)->Instance->CR3)) & ((uint32_t)1 << (((uint16_t)(__IT__)) & UART_IT_MASK)))
+
+/** @brief Clear the specified UART ISR flag, in setting the proper ICR register flag.
+ * @param __HANDLE__: specifies the UART Handle.
+ * This parameter can be UARTx where x: 1, 2, 3 or 4 to select the USART or
+ * UART peripheral. (datasheet: up to four USART/UARTs)
+ * @param __IT_CLEAR__: specifies the interrupt clear register flag that needs to be set
+ * to clear the corresponding interrupt
+ * This parameter can be one of the following values:
+ * @arg UART_CLEAR_PEF: Parity Error Clear Flag
+ * @arg UART_CLEAR_FEF: Framing Error Clear Flag
+ * @arg UART_CLEAR_NEF: Noise detected Clear Flag
+ * @arg UART_CLEAR_OREF: OverRun Error Clear Flag
+ * @arg UART_CLEAR_IDLEF: IDLE line detected Clear Flag
+ * @arg UART_CLEAR_TCF: Transmission Complete Clear Flag
+ * @arg UART_CLEAR_LBDF: LIN Break Detection Clear Flag (not available on F030xx devices)
+ * @arg UART_CLEAR_CTSF: CTS Interrupt Clear Flag
+ * @arg UART_CLEAR_RTOF: Receiver Time Out Clear Flag
+ * @arg UART_CLEAR_EOBF: End Of Block Clear Flag (not available on F030xx devices)
+ * @arg UART_CLEAR_CMF: Character Match Clear Flag
+ * @arg UART_CLEAR_WUF: Wake Up from stop mode Clear Flag (not available on F030xx devices)
+ * @retval None
+ */
+#define __HAL_UART_CLEAR_IT(__HANDLE__, __IT_CLEAR__) ((__HANDLE__)->Instance->ICR = (uint32_t)(__IT_CLEAR__))
+
+/** @brief Set a specific UART request flag.
+ * @param __HANDLE__: specifies the UART Handle.
+ * This parameter can be UARTx where x: 1, 2, 3 or 4 to select the USART or
+ * UART peripheral. (datasheet: up to four USART/UARTs)
+ * @param __REQ__: specifies the request flag to set
+ * This parameter can be one of the following values:
+ * @arg UART_AUTOBAUD_REQUEST: Auto-Baud Rate Request
+ * @arg UART_SENDBREAK_REQUEST: Send Break Request
+ * @arg UART_MUTE_MODE_REQUEST: Mute Mode Request
+ * @arg UART_RXDATA_FLUSH_REQUEST: Receive Data flush Request
+ * @arg UART_TXDATA_FLUSH_REQUEST: Transmit data flush Request (not available on F030xx devices)
+ * @retval None
+ */
+#define __HAL_UART_SEND_REQ(__HANDLE__, __REQ__) ((__HANDLE__)->Instance->RQR |= (uint16_t)(__REQ__))
+
+/** @brief Enable the UART one bit sample method.
+ * @param __HANDLE__: specifies the UART Handle.
+ * @retval None
+ */
+#define __HAL_UART_ONE_BIT_SAMPLE_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3|= USART_CR3_ONEBIT)
+
+/** @brief Disable the UART one bit sample method.
+ * @param __HANDLE__: specifies the UART Handle.
+ * @retval None
+ */
+#define __HAL_UART_ONE_BIT_SAMPLE_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR3 &= (uint32_t)~((uint32_t)USART_CR3_ONEBIT))
+
+/** @brief Enable UART.
+ * @param __HANDLE__: specifies the UART Handle.
+ * The Handle Instance can be UARTx where x: 1, 2, 3, 4 or 5 to select the UART peripheral
+ * @retval None
+ */
+#define __HAL_UART_ENABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 |= USART_CR1_UE)
+
+/** @brief Disable UART.
+ * @param __HANDLE__: specifies the UART Handle.
+ * The Handle Instance can be UARTx where x: 1, 2, 3, 4 or 5 to select the UART peripheral
+ * @retval None
+ */
+#define __HAL_UART_DISABLE(__HANDLE__) ((__HANDLE__)->Instance->CR1 &= ~USART_CR1_UE)
+
+/** @brief Enable CTS flow control.
+ * @note This macro allows to enable CTS hardware flow control for a given UART instance,
+ * without need to call HAL_UART_Init() function.
+ * As involving direct access to UART registers, usage of this macro should be fully endorsed by user.
+ * @note As macro is expected to be used for modifying CTS Hw flow control feature activation, without need
+ * for USART instance Deinit/Init, following conditions for macro call should be fulfilled :
+ * - UART instance should have already been initialised (through call of HAL_UART_Init() )
+ * - macro could only be called when corresponding UART instance is disabled (i.e. __HAL_UART_DISABLE(__HANDLE__))
+ * and should be followed by an Enable macro (i.e. __HAL_UART_ENABLE(__HANDLE__)).
+ * @param __HANDLE__: specifies the UART Handle.
+ * @retval None
+ */
+#define __HAL_UART_HWCONTROL_CTS_ENABLE(__HANDLE__) \
+ do{ \
+ SET_BIT((__HANDLE__)->Instance->CR3, USART_CR3_CTSE); \
+ (__HANDLE__)->Init.HwFlowCtl |= USART_CR3_CTSE; \
+ } while(0)
+
+/** @brief Disable CTS flow control.
+ * @note This macro allows to disable CTS hardware flow control for a given UART instance,
+ * without need to call HAL_UART_Init() function.
+ * As involving direct access to UART registers, usage of this macro should be fully endorsed by user.
+ * @note As macro is expected to be used for modifying CTS Hw flow control feature activation, without need
+ * for USART instance Deinit/Init, following conditions for macro call should be fulfilled :
+ * - UART instance should have already been initialised (through call of HAL_UART_Init() )
+ * - macro could only be called when corresponding UART instance is disabled (i.e. __HAL_UART_DISABLE(__HANDLE__))
+ * and should be followed by an Enable macro (i.e. __HAL_UART_ENABLE(__HANDLE__)).
+ * @param __HANDLE__: specifies the UART Handle.
+ * @retval None
+ */
+#define __HAL_UART_HWCONTROL_CTS_DISABLE(__HANDLE__) \
+ do{ \
+ CLEAR_BIT((__HANDLE__)->Instance->CR3, USART_CR3_CTSE); \
+ (__HANDLE__)->Init.HwFlowCtl &= ~(USART_CR3_CTSE); \
+ } while(0)
+
+/** @brief Enable RTS flow control.
+ * @note This macro allows to enable RTS hardware flow control for a given UART instance,
+ * without need to call HAL_UART_Init() function.
+ * As involving direct access to UART registers, usage of this macro should be fully endorsed by user.
+ * @note As macro is expected to be used for modifying RTS Hw flow control feature activation, without need
+ * for USART instance Deinit/Init, following conditions for macro call should be fulfilled :
+ * - UART instance should have already been initialised (through call of HAL_UART_Init() )
+ * - macro could only be called when corresponding UART instance is disabled (i.e. __HAL_UART_DISABLE(__HANDLE__))
+ * and should be followed by an Enable macro (i.e. __HAL_UART_ENABLE(__HANDLE__)).
+ * @param __HANDLE__: specifies the UART Handle.
+ * @retval None
+ */
+#define __HAL_UART_HWCONTROL_RTS_ENABLE(__HANDLE__) \
+ do{ \
+ SET_BIT((__HANDLE__)->Instance->CR3, USART_CR3_RTSE); \
+ (__HANDLE__)->Init.HwFlowCtl |= USART_CR3_RTSE; \
+ } while(0)
+
+/** @brief Disable RTS flow control.
+ * @note This macro allows to disable RTS hardware flow control for a given UART instance,
+ * without need to call HAL_UART_Init() function.
+ * As involving direct access to UART registers, usage of this macro should be fully endorsed by user.
+ * @note As macro is expected to be used for modifying RTS Hw flow control feature activation, without need
+ * for USART instance Deinit/Init, following conditions for macro call should be fulfilled :
+ * - UART instance should have already been initialised (through call of HAL_UART_Init() )
+ * - macro could only be called when corresponding UART instance is disabled (i.e. __HAL_UART_DISABLE(__HANDLE__))
+ * and should be followed by an Enable macro (i.e. __HAL_UART_ENABLE(__HANDLE__)).
+ * @param __HANDLE__: specifies the UART Handle.
+ * @retval None
+ */
+#define __HAL_UART_HWCONTROL_RTS_DISABLE(__HANDLE__) \
+ do{ \
+ CLEAR_BIT((__HANDLE__)->Instance->CR3, USART_CR3_RTSE);\
+ (__HANDLE__)->Init.HwFlowCtl &= ~(USART_CR3_RTSE); \
+ } while(0)
+
+/**
+ * @}
+ */
+
+/* Private macros --------------------------------------------------------*/
+/** @defgroup UART_Private_Macros UART Private Macros
+ * @{
+ */
+
+/** @brief BRR division operation to set BRR register in 8-bit oversampling mode.
+ * @param __PCLK__: UART clock.
+ * @param __BAUD__: Baud rate set by the user.
+ * @retval Division result
+ */
+#define UART_DIV_SAMPLING8(__PCLK__, __BAUD__) ((((__PCLK__)*2) + ((__BAUD__)/2)) / (__BAUD__))
+
+/** @brief BRR division operation to set BRR register in 16-bit oversampling mode.
+ * @param __PCLK__: UART clock.
+ * @param __BAUD__: Baud rate set by the user.
+ * @retval Division result
+ */
+#define UART_DIV_SAMPLING16(__PCLK__, __BAUD__) (((__PCLK__) + ((__BAUD__)/2)) / (__BAUD__))
+
+/** @brief Check UART Baud rate
+ * @param __BAUDRATE__: Baudrate specified by the user.
+ * The maximum Baud Rate is derived from the maximum clock on F0 (i.e. 48 MHz)
+ * divided by the smallest oversampling used on the USART (i.e. 8)
+ * @retval SET (__BAUDRATE__ is valid) or RESET (__BAUDRATE__ is invalid)
+ */
+#define IS_UART_BAUDRATE(__BAUDRATE__) ((__BAUDRATE__) < 6000001)
+
+/** @brief Check UART assertion time.
+ * @param __TIME__: 5-bit value assertion time.
+ * @retval Test result (TRUE or FALSE).
+ */
+#define IS_UART_ASSERTIONTIME(__TIME__) ((__TIME__) <= 0x1F)
+
+/** @brief Check UART deassertion time.
+ * @param __TIME__: 5-bit value deassertion time.
+ * @retval Test result (TRUE or FALSE).
+ */
+#define IS_UART_DEASSERTIONTIME(__TIME__) ((__TIME__) <= 0x1F)
+
+/**
+ * @brief Ensure that UART frame number of stop bits is valid.
+ * @param __STOPBITS__: UART frame number of stop bits.
+ * @retval SET (__STOPBITS__ is valid) or RESET (__STOPBITS__ is invalid)
+ */
+#ifdef USART_SMARTCARD_SUPPORT
+#define IS_UART_STOPBITS(__STOPBITS__) (((__STOPBITS__) == UART_STOPBITS_0_5) || \
+ ((__STOPBITS__) == UART_STOPBITS_1) || \
+ ((__STOPBITS__) == UART_STOPBITS_1_5) || \
+ ((__STOPBITS__) == UART_STOPBITS_2))
+#else
+#define IS_UART_STOPBITS(__STOPBITS__) (((__STOPBITS__) == UART_STOPBITS_1) || \
+ ((__STOPBITS__) == UART_STOPBITS_2))
+#endif
+
+/**
+ * @brief Ensure that UART frame parity is valid.
+ * @param __PARITY__: UART frame parity.
+ * @retval SET (__PARITY__ is valid) or RESET (__PARITY__ is invalid)
+ */
+#define IS_UART_PARITY(__PARITY__) (((__PARITY__) == UART_PARITY_NONE) || \
+ ((__PARITY__) == UART_PARITY_EVEN) || \
+ ((__PARITY__) == UART_PARITY_ODD))
+
+/**
+ * @brief Ensure that UART hardware flow control is valid.
+ * @param __CONTROL__: UART hardware flow control.
+ * @retval SET (__CONTROL__ is valid) or RESET (__CONTROL__ is invalid)
+ */
+#define IS_UART_HARDWARE_FLOW_CONTROL(__CONTROL__)\
+ (((__CONTROL__) == UART_HWCONTROL_NONE) || \
+ ((__CONTROL__) == UART_HWCONTROL_RTS) || \
+ ((__CONTROL__) == UART_HWCONTROL_CTS) || \
+ ((__CONTROL__) == UART_HWCONTROL_RTS_CTS))
+
+/**
+ * @brief Ensure that UART communication mode is valid.
+ * @param __MODE__: UART communication mode.
+ * @retval SET (__MODE__ is valid) or RESET (__MODE__ is invalid)
+ */
+#define IS_UART_MODE(__MODE__) ((((__MODE__) & (~((uint32_t)(UART_MODE_TX_RX)))) == (uint32_t)0x00) && ((__MODE__) != (uint32_t)0x00))
+
+/**
+ * @brief Ensure that UART state is valid.
+ * @param __STATE__: UART state.
+ * @retval SET (__STATE__ is valid) or RESET (__STATE__ is invalid)
+ */
+#define IS_UART_STATE(__STATE__) (((__STATE__) == UART_STATE_DISABLE) || \
+ ((__STATE__) == UART_STATE_ENABLE))
+
+/**
+ * @brief Ensure that UART oversampling is valid.
+ * @param __SAMPLING__: UART oversampling.
+ * @retval SET (__SAMPLING__ is valid) or RESET (__SAMPLING__ is invalid)
+ */
+#define IS_UART_OVERSAMPLING(__SAMPLING__) (((__SAMPLING__) == UART_OVERSAMPLING_16) || \
+ ((__SAMPLING__) == UART_OVERSAMPLING_8))
+
+/**
+ * @brief Ensure that UART frame sampling is valid.
+ * @param __ONEBIT__: UART frame sampling.
+ * @retval SET (__ONEBIT__ is valid) or RESET (__ONEBIT__ is invalid)
+ */
+#define IS_UART_ONE_BIT_SAMPLE(__ONEBIT__) (((__ONEBIT__) == UART_ONE_BIT_SAMPLE_DISABLE) || \
+ ((__ONEBIT__) == UART_ONE_BIT_SAMPLE_ENABLE))
+
+/**
+ * @brief Ensure that Address Length detection parameter is valid.
+ * @param __ADDRESS__: UART Adress length value.
+ * @retval SET (__ADDRESS__ is valid) or RESET (__ADDRESS__ is invalid)
+ */
+#define IS_UART_ADDRESSLENGTH_DETECT(__ADDRESS__) (((__ADDRESS__) == UART_ADDRESS_DETECT_4B) || \
+ ((__ADDRESS__) == UART_ADDRESS_DETECT_7B))
+
+/**
+ * @brief Ensure that UART receiver timeout setting is valid.
+ * @param __TIMEOUT__: UART receiver timeout setting.
+ * @retval SET (__TIMEOUT__ is valid) or RESET (__TIMEOUT__ is invalid)
+ */
+#define IS_UART_RECEIVER_TIMEOUT(__TIMEOUT__) (((__TIMEOUT__) == UART_RECEIVER_TIMEOUT_DISABLE) || \
+ ((__TIMEOUT__) == UART_RECEIVER_TIMEOUT_ENABLE))
+
+/**
+ * @brief Ensure that UART DMA TX state is valid.
+ * @param __DMATX__: UART DMA TX state.
+ * @retval SET (__DMATX__ is valid) or RESET (__DMATX__ is invalid)
+ */
+#define IS_UART_DMA_TX(__DMATX__) (((__DMATX__) == UART_DMA_TX_DISABLE) || \
+ ((__DMATX__) == UART_DMA_TX_ENABLE))
+
+/**
+ * @brief Ensure that UART DMA RX state is valid.
+ * @param __DMARX__: UART DMA RX state.
+ * @retval SET (__DMARX__ is valid) or RESET (__DMARX__ is invalid)
+ */
+#define IS_UART_DMA_RX(__DMARX__) (((__DMARX__) == UART_DMA_RX_DISABLE) || \
+ ((__DMARX__) == UART_DMA_RX_ENABLE))
+
+/**
+ * @brief Ensure that UART half-duplex state is valid.
+ * @param __HDSEL__: UART half-duplex state.
+ * @retval SET (__HDSEL__ is valid) or RESET (__HDSEL__ is invalid)
+ */
+#define IS_UART_HALF_DUPLEX(__HDSEL__) (((__HDSEL__) == UART_HALF_DUPLEX_DISABLE) || \
+ ((__HDSEL__) == UART_HALF_DUPLEX_ENABLE))
+
+/**
+ * @brief Ensure that UART wake-up method is valid.
+ * @param __WAKEUP__: UART wake-up method .
+ * @retval SET (__WAKEUP__ is valid) or RESET (__WAKEUP__ is invalid)
+ */
+#define IS_UART_WAKEUPMETHOD(__WAKEUP__) (((__WAKEUP__) == UART_WAKEUPMETHOD_IDLELINE) || \
+ ((__WAKEUP__) == UART_WAKEUPMETHOD_ADDRESSMARK))
+
+/**
+ * @brief Ensure that UART advanced features initialization is valid.
+ * @param __INIT__: UART advanced features initialization.
+ * @retval SET (__INIT__ is valid) or RESET (__INIT__ is invalid)
+ */
+#define IS_UART_ADVFEATURE_INIT(__INIT__) ((__INIT__) <= (UART_ADVFEATURE_NO_INIT | \
+ UART_ADVFEATURE_TXINVERT_INIT | \
+ UART_ADVFEATURE_RXINVERT_INIT | \
+ UART_ADVFEATURE_DATAINVERT_INIT | \
+ UART_ADVFEATURE_SWAP_INIT | \
+ UART_ADVFEATURE_RXOVERRUNDISABLE_INIT | \
+ UART_ADVFEATURE_DMADISABLEONERROR_INIT | \
+ UART_ADVFEATURE_AUTOBAUDRATE_INIT | \
+ UART_ADVFEATURE_MSBFIRST_INIT))
+
+/**
+ * @brief Ensure that UART frame TX inversion setting is valid.
+ * @param __TXINV__: UART frame TX inversion setting.
+ * @retval SET (__TXINV__ is valid) or RESET (__TXINV__ is invalid)
+ */
+#define IS_UART_ADVFEATURE_TXINV(__TXINV__) (((__TXINV__) == UART_ADVFEATURE_TXINV_DISABLE) || \
+ ((__TXINV__) == UART_ADVFEATURE_TXINV_ENABLE))
+
+/**
+ * @brief Ensure that UART frame RX inversion setting is valid.
+ * @param __RXINV__: UART frame RX inversion setting.
+ * @retval SET (__RXINV__ is valid) or RESET (__RXINV__ is invalid)
+ */
+#define IS_UART_ADVFEATURE_RXINV(__RXINV__) (((__RXINV__) == UART_ADVFEATURE_RXINV_DISABLE) || \
+ ((__RXINV__) == UART_ADVFEATURE_RXINV_ENABLE))
+
+/**
+ * @brief Ensure that UART frame data inversion setting is valid.
+ * @param __DATAINV__: UART frame data inversion setting.
+ * @retval SET (__DATAINV__ is valid) or RESET (__DATAINV__ is invalid)
+ */
+#define IS_UART_ADVFEATURE_DATAINV(__DATAINV__) (((__DATAINV__) == UART_ADVFEATURE_DATAINV_DISABLE) || \
+ ((__DATAINV__) == UART_ADVFEATURE_DATAINV_ENABLE))
+
+/**
+ * @brief Ensure that UART frame RX/TX pins swap setting is valid.
+ * @param __SWAP__: UART frame RX/TX pins swap setting.
+ * @retval SET (__SWAP__ is valid) or RESET (__SWAP__ is invalid)
+ */
+#define IS_UART_ADVFEATURE_SWAP(__SWAP__) (((__SWAP__) == UART_ADVFEATURE_SWAP_DISABLE) || \
+ ((__SWAP__) == UART_ADVFEATURE_SWAP_ENABLE))
+
+/**
+ * @brief Ensure that UART frame overrun setting is valid.
+ * @param __OVERRUN__: UART frame overrun setting.
+ * @retval SET (__OVERRUN__ is valid) or RESET (__OVERRUN__ is invalid)
+ */
+#define IS_UART_OVERRUN(__OVERRUN__) (((__OVERRUN__) == UART_ADVFEATURE_OVERRUN_ENABLE) || \
+ ((__OVERRUN__) == UART_ADVFEATURE_OVERRUN_DISABLE))
+
+/**
+ * @brief Ensure that UART auto Baud rate state is valid.
+ * @param __AUTOBAUDRATE__: UART auto Baud rate state.
+ * @retval SET (__AUTOBAUDRATE__ is valid) or RESET (__AUTOBAUDRATE__ is invalid)
+ */
+#define IS_UART_ADVFEATURE_AUTOBAUDRATE(__AUTOBAUDRATE__) (((__AUTOBAUDRATE__) == UART_ADVFEATURE_AUTOBAUDRATE_DISABLE) || \
+ ((__AUTOBAUDRATE__) == UART_ADVFEATURE_AUTOBAUDRATE_ENABLE))
+
+/**
+ * @brief Ensure that UART DMA enabling or disabling on error setting is valid.
+ * @param __DMA__: UART DMA enabling or disabling on error setting.
+ * @retval SET (__DMA__ is valid) or RESET (__DMA__ is invalid)
+ */
+#define IS_UART_ADVFEATURE_DMAONRXERROR(__DMA__) (((__DMA__) == UART_ADVFEATURE_DMA_ENABLEONRXERROR) || \
+ ((__DMA__) == UART_ADVFEATURE_DMA_DISABLEONRXERROR))
+
+/**
+ * @brief Ensure that UART frame MSB first setting is valid.
+ * @param __MSBFIRST__: UART frame MSB first setting.
+ * @retval SET (__MSBFIRST__ is valid) or RESET (__MSBFIRST__ is invalid)
+ */
+#define IS_UART_ADVFEATURE_MSBFIRST(__MSBFIRST__) (((__MSBFIRST__) == UART_ADVFEATURE_MSBFIRST_DISABLE) || \
+ ((__MSBFIRST__) == UART_ADVFEATURE_MSBFIRST_ENABLE))
+
+/**
+ * @brief Ensure that UART mute mode state is valid.
+ * @param __MUTE__: UART mute mode state.
+ * @retval SET (__MUTE__ is valid) or RESET (__MUTE__ is invalid)
+ */
+#define IS_UART_MUTE_MODE(__MUTE__) (((__MUTE__) == UART_ADVFEATURE_MUTEMODE_DISABLE) || \
+ ((__MUTE__) == UART_ADVFEATURE_MUTEMODE_ENABLE))
+
+/**
+ * @brief Ensure that UART driver enable polarity is valid.
+ * @param __POLARITY__: UART driver enable polarity.
+ * @retval SET (__POLARITY__ is valid) or RESET (__POLARITY__ is invalid)
+ */
+#define IS_UART_DE_POLARITY(__POLARITY__) (((__POLARITY__) == UART_DE_POLARITY_HIGH) || \
+ ((__POLARITY__) == UART_DE_POLARITY_LOW))
+
+/**
+ * @}
+ */
+
+/* Include UART HAL Extension module */
+#include "stm32f0xx_hal_uart_ex.h"
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup UART_Exported_Functions UART Exported Functions
+ * @{
+ */
+
+/** @addtogroup UART_Exported_Functions_Group1 Initialization and de-initialization functions
+ * @{
+ */
+
+/* Initialization and de-initialization functions ****************************/
+HAL_StatusTypeDef HAL_UART_Init(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_HalfDuplex_Init(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_MultiProcessor_Init(UART_HandleTypeDef *huart, uint8_t Address, uint32_t WakeUpMethod);
+HAL_StatusTypeDef HAL_UART_DeInit (UART_HandleTypeDef *huart);
+void HAL_UART_MspInit(UART_HandleTypeDef *huart);
+void HAL_UART_MspDeInit(UART_HandleTypeDef *huart);
+
+/**
+ * @}
+ */
+
+/** @addtogroup UART_Exported_Functions_Group2 IO operation functions
+ * @{
+ */
+
+/* IO operation functions *****************************************************/
+HAL_StatusTypeDef HAL_UART_Transmit(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_UART_Receive(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size, uint32_t Timeout);
+HAL_StatusTypeDef HAL_UART_Transmit_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_UART_Receive_IT(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_UART_Transmit_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_UART_Receive_DMA(UART_HandleTypeDef *huart, uint8_t *pData, uint16_t Size);
+HAL_StatusTypeDef HAL_UART_DMAPause(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_UART_DMAResume(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_UART_DMAStop(UART_HandleTypeDef *huart);
+void HAL_UART_IRQHandler(UART_HandleTypeDef *huart);
+void HAL_UART_TxCpltCallback(UART_HandleTypeDef *huart);
+void HAL_UART_TxHalfCpltCallback(UART_HandleTypeDef *huart);
+void HAL_UART_RxCpltCallback(UART_HandleTypeDef *huart);
+void HAL_UART_RxHalfCpltCallback(UART_HandleTypeDef *huart);
+void HAL_UART_ErrorCallback(UART_HandleTypeDef *huart);
+
+/**
+ * @}
+ */
+
+/** @addtogroup UART_Exported_Functions_Group3 Peripheral Control functions
+ * @{
+ */
+
+/* Peripheral Control functions ************************************************/
+HAL_StatusTypeDef HAL_MultiProcessor_EnableMuteMode(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_MultiProcessor_DisableMuteMode(UART_HandleTypeDef *huart);
+void HAL_MultiProcessor_EnterMuteMode(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_HalfDuplex_EnableTransmitter(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef HAL_HalfDuplex_EnableReceiver(UART_HandleTypeDef *huart);
+
+/**
+ * @}
+ */
+
+/** @addtogroup UART_Exported_Functions_Group4 Peripheral State and Error functions
+ * @{
+ */
+
+/* Peripheral State and Errors functions **************************************************/
+HAL_UART_StateTypeDef HAL_UART_GetState(UART_HandleTypeDef *huart);
+uint32_t HAL_UART_GetError(UART_HandleTypeDef *huart);
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/* Private functions -----------------------------------------------------------*/
+/** @addtogroup UART_Private_Functions
+ * @{
+ */
+void UART_AdvFeatureConfig(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef UART_CheckIdleState(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef UART_SetConfig(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef UART_Transmit_IT(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef UART_EndTransmit_IT(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef UART_Receive_IT(UART_HandleTypeDef *huart);
+HAL_StatusTypeDef UART_WaitOnFlagUntilTimeout(UART_HandleTypeDef *huart, uint32_t Flag, FlagStatus Status, uint32_t Timeout);
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F0xx_HAL_UART_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+
