mbed official
mbed library sources. Supersedes mbed-src.
Dependents: Nucleo_Hello_Encoder BLE_iBeaconScan AM1805_DEMO DISCO-F429ZI_ExportTemplate1 ... more
Diff: targets/TARGET_STM/TARGET_STM32F0/device/stm32f0xx_hal_rcc.h
- Revision:
- 149:156823d33999
- Parent:
- 144:ef7eb2e8f9f7
- Child:
- 156:95d6b41a828b
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/TARGET_STM/TARGET_STM32F0/device/stm32f0xx_hal_rcc.h Fri Oct 28 11:17:30 2016 +0100
@@ -0,0 +1,1704 @@
+/**
+ ******************************************************************************
+ * @file stm32f0xx_hal_rcc.h
+ * @author MCD Application Team
+ * @version V1.4.0
+ * @date 27-May-2016
+ * @brief Header file of RCC HAL module.
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2016 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32F0xx_HAL_RCC_H
+#define __STM32F0xx_HAL_RCC_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f0xx_hal_def.h"
+
+/** @addtogroup STM32F0xx_HAL_Driver
+ * @{
+ */
+
+/** @addtogroup RCC
+ * @{
+ */
+
+/** @addtogroup RCC_Private_Constants
+ * @{
+ */
+
+/** @defgroup RCC_Timeout RCC Timeout
+ * @{
+ */
+
+/* Disable Backup domain write protection state change timeout */
+#define RCC_DBP_TIMEOUT_VALUE ((uint32_t)100) /* 100 ms */
+/* LSE state change timeout */
+#define RCC_LSE_TIMEOUT_VALUE LSE_STARTUP_TIMEOUT
+#define CLOCKSWITCH_TIMEOUT_VALUE ((uint32_t)5000) /* 5 s */
+#define HSE_TIMEOUT_VALUE HSE_STARTUP_TIMEOUT
+#define HSI_TIMEOUT_VALUE ((uint32_t)2) /* 2 ms (minimum Tick + 1) */
+#define LSI_TIMEOUT_VALUE ((uint32_t)2) /* 2 ms (minimum Tick + 1) */
+#define PLL_TIMEOUT_VALUE ((uint32_t)2) /* 2 ms (minimum Tick + 1) */
+#define HSI14_TIMEOUT_VALUE ((uint32_t)2) /* 2 ms (minimum Tick + 1) */
+#if defined(RCC_HSI48_SUPPORT)
+#define HSI48_TIMEOUT_VALUE ((uint32_t)2) /* 2 ms (minimum Tick + 1) */
+#endif /* RCC_HSI48_SUPPORT */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_Register_Offset Register offsets
+ * @{
+ */
+#define RCC_OFFSET (RCC_BASE - PERIPH_BASE)
+#define RCC_CR_OFFSET 0x00
+#define RCC_CFGR_OFFSET 0x04
+#define RCC_CIR_OFFSET 0x08
+#define RCC_BDCR_OFFSET 0x20
+#define RCC_CSR_OFFSET 0x24
+
+/**
+ * @}
+ */
+
+
+/* CR register byte 2 (Bits[23:16]) base address */
+#define RCC_CR_BYTE2_ADDRESS ((uint32_t)(RCC_BASE + RCC_CR_OFFSET + 0x02))
+
+/* CIR register byte 1 (Bits[15:8]) base address */
+#define RCC_CIR_BYTE1_ADDRESS ((uint32_t)(RCC_BASE + RCC_CIR_OFFSET + 0x01))
+
+/* CIR register byte 2 (Bits[23:16]) base address */
+#define RCC_CIR_BYTE2_ADDRESS ((uint32_t)(RCC_BASE + RCC_CIR_OFFSET + 0x02))
+
+/* Defines used for Flags */
+#define CR_REG_INDEX ((uint8_t)1)
+#define CR2_REG_INDEX ((uint8_t)2)
+#define BDCR_REG_INDEX ((uint8_t)3)
+#define CSR_REG_INDEX ((uint8_t)4)
+
+/* Bits position in in the CFGR register */
+#define RCC_CFGR_PLLMUL_BITNUMBER 18U
+#define RCC_CFGR_HPRE_BITNUMBER 4U
+#define RCC_CFGR_PPRE_BITNUMBER 8U
+/* Flags in the CFGR2 register */
+#define RCC_CFGR2_PREDIV_BITNUMBER 0
+/* Flags in the CR register */
+#define RCC_CR_HSIRDY_BitNumber 1
+#define RCC_CR_HSERDY_BitNumber 17
+#define RCC_CR_PLLRDY_BitNumber 25
+/* Flags in the CR2 register */
+#define RCC_CR2_HSI14RDY_BitNumber 1
+#define RCC_CR2_HSI48RDY_BitNumber 16
+/* Flags in the BDCR register */
+#define RCC_BDCR_LSERDY_BitNumber 1
+/* Flags in the CSR register */
+#define RCC_CSR_LSIRDY_BitNumber 1
+#define RCC_CSR_V18PWRRSTF_BitNumber 23
+#define RCC_CSR_RMVF_BitNumber 24
+#define RCC_CSR_OBLRSTF_BitNumber 25
+#define RCC_CSR_PINRSTF_BitNumber 26
+#define RCC_CSR_PORRSTF_BitNumber 27
+#define RCC_CSR_SFTRSTF_BitNumber 28
+#define RCC_CSR_IWDGRSTF_BitNumber 29
+#define RCC_CSR_WWDGRSTF_BitNumber 30
+#define RCC_CSR_LPWRRSTF_BitNumber 31
+/* Flags in the HSITRIM register */
+#define RCC_CR_HSITRIM_BitNumber 3
+#define RCC_HSI14TRIM_BIT_NUMBER 3
+#define RCC_FLAG_MASK ((uint8_t)0x1F)
+
+/**
+ * @}
+ */
+
+/** @addtogroup RCC_Private_Macros
+ * @{
+ */
+#define IS_RCC_HSE(__HSE__) (((__HSE__) == RCC_HSE_OFF) || ((__HSE__) == RCC_HSE_ON) || \
+ ((__HSE__) == RCC_HSE_BYPASS))
+#define IS_RCC_LSE(__LSE__) (((__LSE__) == RCC_LSE_OFF) || ((__LSE__) == RCC_LSE_ON) || \
+ ((__LSE__) == RCC_LSE_BYPASS))
+#define IS_RCC_HSI(__HSI__) (((__HSI__) == RCC_HSI_OFF) || ((__HSI__) == RCC_HSI_ON))
+#define IS_RCC_HSI14(__HSI14__) (((__HSI14__) == RCC_HSI14_OFF) || ((__HSI14__) == RCC_HSI14_ON) || ((__HSI14__) == RCC_HSI14_ADC_CONTROL))
+#define IS_RCC_CALIBRATION_VALUE(__VALUE__) ((__VALUE__) <= 0x1F)
+#define IS_RCC_LSI(__LSI__) (((__LSI__) == RCC_LSI_OFF) || ((__LSI__) == RCC_LSI_ON))
+#define IS_RCC_PLL(__PLL__) (((__PLL__) == RCC_PLL_NONE) || ((__PLL__) == RCC_PLL_OFF) || \
+ ((__PLL__) == RCC_PLL_ON))
+#define IS_RCC_PREDIV(__PREDIV__) (((__PREDIV__) == RCC_PREDIV_DIV1) || ((__PREDIV__) == RCC_PREDIV_DIV2) || \
+ ((__PREDIV__) == RCC_PREDIV_DIV3) || ((__PREDIV__) == RCC_PREDIV_DIV4) || \
+ ((__PREDIV__) == RCC_PREDIV_DIV5) || ((__PREDIV__) == RCC_PREDIV_DIV6) || \
+ ((__PREDIV__) == RCC_PREDIV_DIV7) || ((__PREDIV__) == RCC_PREDIV_DIV8) || \
+ ((__PREDIV__) == RCC_PREDIV_DIV9) || ((__PREDIV__) == RCC_PREDIV_DIV10) || \
+ ((__PREDIV__) == RCC_PREDIV_DIV11) || ((__PREDIV__) == RCC_PREDIV_DIV12) || \
+ ((__PREDIV__) == RCC_PREDIV_DIV13) || ((__PREDIV__) == RCC_PREDIV_DIV14) || \
+ ((__PREDIV__) == RCC_PREDIV_DIV15) || ((__PREDIV__) == RCC_PREDIV_DIV16))
+
+#define IS_RCC_PLL_MUL(__MUL__) (((__MUL__) == RCC_PLL_MUL2) || ((__MUL__) == RCC_PLL_MUL3) || \
+ ((__MUL__) == RCC_PLL_MUL4) || ((__MUL__) == RCC_PLL_MUL5) || \
+ ((__MUL__) == RCC_PLL_MUL6) || ((__MUL__) == RCC_PLL_MUL7) || \
+ ((__MUL__) == RCC_PLL_MUL8) || ((__MUL__) == RCC_PLL_MUL9) || \
+ ((__MUL__) == RCC_PLL_MUL10) || ((__MUL__) == RCC_PLL_MUL11) || \
+ ((__MUL__) == RCC_PLL_MUL12) || ((__MUL__) == RCC_PLL_MUL13) || \
+ ((__MUL__) == RCC_PLL_MUL14) || ((__MUL__) == RCC_PLL_MUL15) || \
+ ((__MUL__) == RCC_PLL_MUL16))
+#define IS_RCC_CLOCKTYPE(__CLK__) ((((__CLK__) & RCC_CLOCKTYPE_SYSCLK) == RCC_CLOCKTYPE_SYSCLK) || \
+ (((__CLK__) & RCC_CLOCKTYPE_HCLK) == RCC_CLOCKTYPE_HCLK) || \
+ (((__CLK__) & RCC_CLOCKTYPE_PCLK1) == RCC_CLOCKTYPE_PCLK1))
+#define IS_RCC_HCLK(__HCLK__) (((__HCLK__) == RCC_SYSCLK_DIV1) || ((__HCLK__) == RCC_SYSCLK_DIV2) || \
+ ((__HCLK__) == RCC_SYSCLK_DIV4) || ((__HCLK__) == RCC_SYSCLK_DIV8) || \
+ ((__HCLK__) == RCC_SYSCLK_DIV16) || ((__HCLK__) == RCC_SYSCLK_DIV64) || \
+ ((__HCLK__) == RCC_SYSCLK_DIV128) || ((__HCLK__) == RCC_SYSCLK_DIV256) || \
+ ((__HCLK__) == RCC_SYSCLK_DIV512))
+#define IS_RCC_PCLK(__PCLK__) (((__PCLK__) == RCC_HCLK_DIV1) || ((__PCLK__) == RCC_HCLK_DIV2) || \
+ ((__PCLK__) == RCC_HCLK_DIV4) || ((__PCLK__) == RCC_HCLK_DIV8) || \
+ ((__PCLK__) == RCC_HCLK_DIV16))
+#define IS_RCC_MCO(__MCO__) ((__MCO__) == RCC_MCO)
+#define IS_RCC_RTCCLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_RTCCLKSOURCE_NO_CLK) || \
+ ((__SOURCE__) == RCC_RTCCLKSOURCE_LSE) || \
+ ((__SOURCE__) == RCC_RTCCLKSOURCE_LSI) || \
+ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV32))
+#define IS_RCC_USART1CLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_USART1CLKSOURCE_PCLK1) || \
+ ((__SOURCE__) == RCC_USART1CLKSOURCE_SYSCLK) || \
+ ((__SOURCE__) == RCC_USART1CLKSOURCE_LSE) || \
+ ((__SOURCE__) == RCC_USART1CLKSOURCE_HSI))
+#define IS_RCC_I2C1CLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_I2C1CLKSOURCE_HSI) || \
+ ((__SOURCE__) == RCC_I2C1CLKSOURCE_SYSCLK))
+
+/**
+ * @}
+ */
+
+/* Exported types ------------------------------------------------------------*/
+
+/** @defgroup RCC_Exported_Types RCC Exported Types
+ * @{
+ */
+
+/**
+ * @brief RCC PLL configuration structure definition
+ */
+typedef struct
+{
+ uint32_t PLLState; /*!< PLLState: The new state of the PLL.
+ This parameter can be a value of @ref RCC_PLL_Config */
+
+ uint32_t PLLSource; /*!< PLLSource: PLL entry clock source.
+ This parameter must be a value of @ref RCC_PLL_Clock_Source */
+
+ uint32_t PLLMUL; /*!< PLLMUL: Multiplication factor for PLL VCO input clock
+ This parameter must be a value of @ref RCC_PLL_Multiplication_Factor*/
+
+ uint32_t PREDIV; /*!< PREDIV: Predivision factor for PLL VCO input clock
+ This parameter must be a value of @ref RCC_PLL_Prediv_Factor */
+
+} RCC_PLLInitTypeDef;
+
+/**
+ * @brief RCC Internal/External Oscillator (HSE, HSI, LSE and LSI) configuration structure definition
+ */
+typedef struct
+{
+ uint32_t OscillatorType; /*!< The oscillators to be configured.
+ This parameter can be a value of @ref RCC_Oscillator_Type */
+
+ uint32_t HSEState; /*!< The new state of the HSE.
+ This parameter can be a value of @ref RCC_HSE_Config */
+
+ uint32_t LSEState; /*!< The new state of the LSE.
+ This parameter can be a value of @ref RCC_LSE_Config */
+
+ uint32_t HSIState; /*!< The new state of the HSI.
+ This parameter can be a value of @ref RCC_HSI_Config */
+
+ uint32_t HSICalibrationValue; /*!< The HSI calibration trimming value (default is RCC_HSICALIBRATION_DEFAULT).
+ This parameter must be a number between Min_Data = 0x00 and Max_Data = 0x1F */
+
+ uint32_t HSI14State; /*!< The new state of the HSI14.
+ This parameter can be a value of @ref RCC_HSI14_Config */
+
+ uint32_t HSI14CalibrationValue; /*!< The HSI14 calibration trimming value (default is RCC_HSI14CALIBRATION_DEFAULT).
+ This parameter must be a number between Min_Data = 0x00 and Max_Data = 0x1F */
+
+ uint32_t LSIState; /*!< The new state of the LSI.
+ This parameter can be a value of @ref RCC_LSI_Config */
+
+ uint32_t HSI48State; /*!< The new state of the HSI48.
+ This parameter can be a value of @ref RCC_HSI48_Config */
+
+ RCC_PLLInitTypeDef PLL; /*!< PLL structure parameters */
+
+} RCC_OscInitTypeDef;
+
+/**
+ * @brief RCC System, AHB and APB busses clock configuration structure definition
+ */
+typedef struct
+{
+ uint32_t ClockType; /*!< The clock to be configured.
+ This parameter can be a value of @ref RCC_System_Clock_Type */
+
+ uint32_t SYSCLKSource; /*!< The clock source (SYSCLKS) used as system clock.
+ This parameter can be a value of @ref RCC_System_Clock_Source */
+
+ uint32_t AHBCLKDivider; /*!< The AHB clock (HCLK) divider. This clock is derived from the system clock (SYSCLK).
+ This parameter can be a value of @ref RCC_AHB_Clock_Source */
+
+ uint32_t APB1CLKDivider; /*!< The APB1 clock (PCLK1) divider. This clock is derived from the AHB clock (HCLK).
+ This parameter can be a value of @ref RCC_APB1_Clock_Source */
+
+} RCC_ClkInitTypeDef;
+
+/**
+ * @}
+ */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup RCC_Exported_Constants RCC Exported Constants
+ * @{
+ */
+
+/** @defgroup RCC_PLL_Clock_Source PLL Clock Source
+ * @{
+ */
+
+#define RCC_PLLSOURCE_HSE RCC_CFGR_PLLSRC_HSE_PREDIV /*!< HSE clock selected as PLL entry clock source */
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_Oscillator_Type Oscillator Type
+ * @{
+ */
+#define RCC_OSCILLATORTYPE_NONE ((uint32_t)0x00000000)
+#define RCC_OSCILLATORTYPE_HSE ((uint32_t)0x00000001)
+#define RCC_OSCILLATORTYPE_HSI ((uint32_t)0x00000002)
+#define RCC_OSCILLATORTYPE_LSE ((uint32_t)0x00000004)
+#define RCC_OSCILLATORTYPE_LSI ((uint32_t)0x00000008)
+#define RCC_OSCILLATORTYPE_HSI14 ((uint32_t)0x00000010)
+#if defined(RCC_HSI48_SUPPORT)
+#define RCC_OSCILLATORTYPE_HSI48 ((uint32_t)0x00000020)
+#endif /* RCC_HSI48_SUPPORT */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_HSE_Config HSE Config
+ * @{
+ */
+#define RCC_HSE_OFF ((uint32_t)0x00000000) /*!< HSE clock deactivation */
+#define RCC_HSE_ON ((uint32_t)0x00000001) /*!< HSE clock activation */
+#define RCC_HSE_BYPASS ((uint32_t)0x00000005) /*!< External clock source for HSE clock */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_LSE_Config LSE Config
+ * @{
+ */
+#define RCC_LSE_OFF ((uint32_t)0x00000000) /*!< LSE clock deactivation */
+#define RCC_LSE_ON ((uint32_t)0x00000001) /*!< LSE clock activation */
+#define RCC_LSE_BYPASS ((uint32_t)0x00000005) /*!< External clock source for LSE clock */
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_HSI_Config HSI Config
+ * @{
+ */
+#define RCC_HSI_OFF ((uint32_t)0x00000000) /*!< HSI clock deactivation */
+#define RCC_HSI_ON RCC_CR_HSION /*!< HSI clock activation */
+
+#define RCC_HSICALIBRATION_DEFAULT ((uint32_t)0x10) /* Default HSI calibration trimming value */
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_HSI14_Config RCC HSI14 Config
+ * @{
+ */
+#define RCC_HSI14_OFF ((uint32_t)0x00)
+#define RCC_HSI14_ON RCC_CR2_HSI14ON
+#define RCC_HSI14_ADC_CONTROL (~RCC_CR2_HSI14DIS)
+
+#define RCC_HSI14CALIBRATION_DEFAULT ((uint32_t)0x10) /* Default HSI14 calibration trimming value */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_LSI_Config LSI Config
+ * @{
+ */
+#define RCC_LSI_OFF ((uint32_t)0x00000000) /*!< LSI clock deactivation */
+#define RCC_LSI_ON RCC_CSR_LSION /*!< LSI clock activation */
+
+/**
+ * @}
+ */
+
+#if defined(RCC_HSI48_SUPPORT)
+/** @defgroup RCC_HSI48_Config HSI48 Config
+ * @{
+ */
+#define RCC_HSI48_OFF ((uint8_t)0x00)
+#define RCC_HSI48_ON ((uint8_t)0x01)
+
+/**
+ * @}
+ */
+#endif /* RCC_HSI48_SUPPORT */
+
+/** @defgroup RCC_PLL_Config PLL Config
+ * @{
+ */
+#define RCC_PLL_NONE ((uint32_t)0x00000000) /*!< PLL is not configured */
+#define RCC_PLL_OFF ((uint32_t)0x00000001) /*!< PLL deactivation */
+#define RCC_PLL_ON ((uint32_t)0x00000002) /*!< PLL activation */
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_System_Clock_Type System Clock Type
+ * @{
+ */
+#define RCC_CLOCKTYPE_SYSCLK ((uint32_t)0x00000001) /*!< SYSCLK to configure */
+#define RCC_CLOCKTYPE_HCLK ((uint32_t)0x00000002) /*!< HCLK to configure */
+#define RCC_CLOCKTYPE_PCLK1 ((uint32_t)0x00000004) /*!< PCLK1 to configure */
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_System_Clock_Source System Clock Source
+ * @{
+ */
+#define RCC_SYSCLKSOURCE_HSI RCC_CFGR_SW_HSI /*!< HSI selected as system clock */
+#define RCC_SYSCLKSOURCE_HSE RCC_CFGR_SW_HSE /*!< HSE selected as system clock */
+#define RCC_SYSCLKSOURCE_PLLCLK RCC_CFGR_SW_PLL /*!< PLL selected as system clock */
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_System_Clock_Source_Status System Clock Source Status
+ * @{
+ */
+#define RCC_SYSCLKSOURCE_STATUS_HSI RCC_CFGR_SWS_HSI /*!< HSI used as system clock */
+#define RCC_SYSCLKSOURCE_STATUS_HSE RCC_CFGR_SWS_HSE /*!< HSE used as system clock */
+#define RCC_SYSCLKSOURCE_STATUS_PLLCLK RCC_CFGR_SWS_PLL /*!< PLL used as system clock */
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_AHB_Clock_Source AHB Clock Source
+ * @{
+ */
+#define RCC_SYSCLK_DIV1 RCC_CFGR_HPRE_DIV1 /*!< SYSCLK not divided */
+#define RCC_SYSCLK_DIV2 RCC_CFGR_HPRE_DIV2 /*!< SYSCLK divided by 2 */
+#define RCC_SYSCLK_DIV4 RCC_CFGR_HPRE_DIV4 /*!< SYSCLK divided by 4 */
+#define RCC_SYSCLK_DIV8 RCC_CFGR_HPRE_DIV8 /*!< SYSCLK divided by 8 */
+#define RCC_SYSCLK_DIV16 RCC_CFGR_HPRE_DIV16 /*!< SYSCLK divided by 16 */
+#define RCC_SYSCLK_DIV64 RCC_CFGR_HPRE_DIV64 /*!< SYSCLK divided by 64 */
+#define RCC_SYSCLK_DIV128 RCC_CFGR_HPRE_DIV128 /*!< SYSCLK divided by 128 */
+#define RCC_SYSCLK_DIV256 RCC_CFGR_HPRE_DIV256 /*!< SYSCLK divided by 256 */
+#define RCC_SYSCLK_DIV512 RCC_CFGR_HPRE_DIV512 /*!< SYSCLK divided by 512 */
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_APB1_Clock_Source RCC APB1 Clock Source
+ * @{
+ */
+#define RCC_HCLK_DIV1 RCC_CFGR_PPRE_DIV1 /*!< HCLK not divided */
+#define RCC_HCLK_DIV2 RCC_CFGR_PPRE_DIV2 /*!< HCLK divided by 2 */
+#define RCC_HCLK_DIV4 RCC_CFGR_PPRE_DIV4 /*!< HCLK divided by 4 */
+#define RCC_HCLK_DIV8 RCC_CFGR_PPRE_DIV8 /*!< HCLK divided by 8 */
+#define RCC_HCLK_DIV16 RCC_CFGR_PPRE_DIV16 /*!< HCLK divided by 16 */
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_RTC_Clock_Source RTC Clock Source
+ * @{
+ */
+#define RCC_RTCCLKSOURCE_NO_CLK ((uint32_t)0x00000000) /*!< No clock */
+#define RCC_RTCCLKSOURCE_LSE RCC_BDCR_RTCSEL_LSE /*!< LSE oscillator clock used as RTC clock */
+#define RCC_RTCCLKSOURCE_LSI RCC_BDCR_RTCSEL_LSI /*!< LSI oscillator clock used as RTC clock */
+#define RCC_RTCCLKSOURCE_HSE_DIV32 RCC_BDCR_RTCSEL_HSE /*!< HSE oscillator clock divided by 32 used as RTC clock */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_PLL_Multiplication_Factor RCC PLL Multiplication Factor
+ * @{
+ */
+#define RCC_PLL_MUL2 RCC_CFGR_PLLMUL2
+#define RCC_PLL_MUL3 RCC_CFGR_PLLMUL3
+#define RCC_PLL_MUL4 RCC_CFGR_PLLMUL4
+#define RCC_PLL_MUL5 RCC_CFGR_PLLMUL5
+#define RCC_PLL_MUL6 RCC_CFGR_PLLMUL6
+#define RCC_PLL_MUL7 RCC_CFGR_PLLMUL7
+#define RCC_PLL_MUL8 RCC_CFGR_PLLMUL8
+#define RCC_PLL_MUL9 RCC_CFGR_PLLMUL9
+#define RCC_PLL_MUL10 RCC_CFGR_PLLMUL10
+#define RCC_PLL_MUL11 RCC_CFGR_PLLMUL11
+#define RCC_PLL_MUL12 RCC_CFGR_PLLMUL12
+#define RCC_PLL_MUL13 RCC_CFGR_PLLMUL13
+#define RCC_PLL_MUL14 RCC_CFGR_PLLMUL14
+#define RCC_PLL_MUL15 RCC_CFGR_PLLMUL15
+#define RCC_PLL_MUL16 RCC_CFGR_PLLMUL16
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_PLL_Prediv_Factor RCC PLL Prediv Factor
+ * @{
+ */
+
+#define RCC_PREDIV_DIV1 RCC_CFGR2_PREDIV_DIV1
+#define RCC_PREDIV_DIV2 RCC_CFGR2_PREDIV_DIV2
+#define RCC_PREDIV_DIV3 RCC_CFGR2_PREDIV_DIV3
+#define RCC_PREDIV_DIV4 RCC_CFGR2_PREDIV_DIV4
+#define RCC_PREDIV_DIV5 RCC_CFGR2_PREDIV_DIV5
+#define RCC_PREDIV_DIV6 RCC_CFGR2_PREDIV_DIV6
+#define RCC_PREDIV_DIV7 RCC_CFGR2_PREDIV_DIV7
+#define RCC_PREDIV_DIV8 RCC_CFGR2_PREDIV_DIV8
+#define RCC_PREDIV_DIV9 RCC_CFGR2_PREDIV_DIV9
+#define RCC_PREDIV_DIV10 RCC_CFGR2_PREDIV_DIV10
+#define RCC_PREDIV_DIV11 RCC_CFGR2_PREDIV_DIV11
+#define RCC_PREDIV_DIV12 RCC_CFGR2_PREDIV_DIV12
+#define RCC_PREDIV_DIV13 RCC_CFGR2_PREDIV_DIV13
+#define RCC_PREDIV_DIV14 RCC_CFGR2_PREDIV_DIV14
+#define RCC_PREDIV_DIV15 RCC_CFGR2_PREDIV_DIV15
+#define RCC_PREDIV_DIV16 RCC_CFGR2_PREDIV_DIV16
+
+/**
+ * @}
+ */
+
+
+/** @defgroup RCC_USART1_Clock_Source RCC USART1 Clock Source
+ * @{
+ */
+#define RCC_USART1CLKSOURCE_PCLK1 RCC_CFGR3_USART1SW_PCLK
+#define RCC_USART1CLKSOURCE_SYSCLK RCC_CFGR3_USART1SW_SYSCLK
+#define RCC_USART1CLKSOURCE_LSE RCC_CFGR3_USART1SW_LSE
+#define RCC_USART1CLKSOURCE_HSI RCC_CFGR3_USART1SW_HSI
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_I2C1_Clock_Source RCC I2C1 Clock Source
+ * @{
+ */
+#define RCC_I2C1CLKSOURCE_HSI RCC_CFGR3_I2C1SW_HSI
+#define RCC_I2C1CLKSOURCE_SYSCLK RCC_CFGR3_I2C1SW_SYSCLK
+
+/**
+ * @}
+ */
+/** @defgroup RCC_MCO_Index MCO Index
+ * @{
+ */
+#define RCC_MCO1 ((uint32_t)0x00000000)
+#define RCC_MCO RCC_MCO1 /*!< MCO1 to be compliant with other families with 2 MCOs*/
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_MCO_Clock_Source RCC MCO Clock Source
+ * @{
+ */
+#define RCC_MCO1SOURCE_NOCLOCK RCC_CFGR_MCO_NOCLOCK
+#define RCC_MCO1SOURCE_LSI RCC_CFGR_MCO_LSI
+#define RCC_MCO1SOURCE_LSE RCC_CFGR_MCO_LSE
+#define RCC_MCO1SOURCE_SYSCLK RCC_CFGR_MCO_SYSCLK
+#define RCC_MCO1SOURCE_HSI RCC_CFGR_MCO_HSI
+#define RCC_MCO1SOURCE_HSE RCC_CFGR_MCO_HSE
+#define RCC_MCO1SOURCE_PLLCLK_DIV2 RCC_CFGR_MCO_PLL
+#define RCC_MCO1SOURCE_HSI14 RCC_CFGR_MCO_HSI14
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_Interrupt Interrupts
+ * @{
+ */
+#define RCC_IT_LSIRDY ((uint8_t)RCC_CIR_LSIRDYF) /*!< LSI Ready Interrupt flag */
+#define RCC_IT_LSERDY ((uint8_t)RCC_CIR_LSERDYF) /*!< LSE Ready Interrupt flag */
+#define RCC_IT_HSIRDY ((uint8_t)RCC_CIR_HSIRDYF) /*!< HSI Ready Interrupt flag */
+#define RCC_IT_HSERDY ((uint8_t)RCC_CIR_HSERDYF) /*!< HSE Ready Interrupt flag */
+#define RCC_IT_PLLRDY ((uint8_t)RCC_CIR_PLLRDYF) /*!< PLL Ready Interrupt flag */
+#define RCC_IT_HSI14RDY ((uint8_t)RCC_CIR_HSI14RDYF) /*!< HSI14 Ready Interrupt flag */
+#if defined(RCC_CIR_HSI48RDYF)
+#define RCC_IT_HSI48RDY ((uint8_t)RCC_CIR_HSI48RDYF) /*!< HSI48 Ready Interrupt flag */
+#endif
+#define RCC_IT_CSS ((uint8_t)RCC_CIR_CSSF) /*!< Clock Security System Interrupt flag */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_Flag Flags
+ * Elements values convention: XXXYYYYYb
+ * - YYYYY : Flag position in the register
+ * - XXX : Register index
+ * - 001: CR register
+ * - 010: CR2 register
+ * - 011: BDCR register
+ * - 0100: CSR register
+ * @{
+ */
+/* Flags in the CR register */
+#define RCC_FLAG_HSIRDY ((uint8_t)((CR_REG_INDEX << 5) | RCC_CR_HSIRDY_BitNumber))
+#define RCC_FLAG_HSERDY ((uint8_t)((CR_REG_INDEX << 5) | RCC_CR_HSERDY_BitNumber))
+#define RCC_FLAG_PLLRDY ((uint8_t)((CR_REG_INDEX << 5) | RCC_CR_PLLRDY_BitNumber))
+/* Flags in the CR2 register */
+#define RCC_FLAG_HSI14RDY ((uint8_t)((CR2_REG_INDEX << 5) | RCC_CR2_HSI14RDY_BitNumber))
+
+/* Flags in the CSR register */
+#define RCC_FLAG_LSIRDY ((uint8_t)((CSR_REG_INDEX << 5) | RCC_CSR_LSIRDY_BitNumber))
+#if defined(RCC_CSR_V18PWRRSTF)
+#define RCC_FLAG_V18PWRRST ((uint8_t)((CSR_REG_INDEX << 5) | RCC_CSR_V18PWRRSTF_BitNumber))
+#endif
+#define RCC_FLAG_OBLRST ((uint8_t)((CSR_REG_INDEX << 5) | RCC_CSR_OBLRSTF_BitNumber))
+#define RCC_FLAG_PINRST ((uint8_t)((CSR_REG_INDEX << 5) | RCC_CSR_PINRSTF_BitNumber)) /*!< PIN reset flag */
+#define RCC_FLAG_PORRST ((uint8_t)((CSR_REG_INDEX << 5) | RCC_CSR_PORRSTF_BitNumber)) /*!< POR/PDR reset flag */
+#define RCC_FLAG_SFTRST ((uint8_t)((CSR_REG_INDEX << 5) | RCC_CSR_SFTRSTF_BitNumber)) /*!< Software Reset flag */
+#define RCC_FLAG_IWDGRST ((uint8_t)((CSR_REG_INDEX << 5) | RCC_CSR_IWDGRSTF_BitNumber)) /*!< Independent Watchdog reset flag */
+#define RCC_FLAG_WWDGRST ((uint8_t)((CSR_REG_INDEX << 5) | RCC_CSR_WWDGRSTF_BitNumber)) /*!< Window watchdog reset flag */
+#define RCC_FLAG_LPWRRST ((uint8_t)((CSR_REG_INDEX << 5) | RCC_CSR_LPWRRSTF_BitNumber)) /*!< Low-Power reset flag */
+
+/* Flags in the BDCR register */
+#define RCC_FLAG_LSERDY ((uint8_t)((BDCR_REG_INDEX << 5) | RCC_BDCR_LSERDY_BitNumber)) /*!< External Low Speed oscillator Ready */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/* Exported macro ------------------------------------------------------------*/
+
+/** @defgroup RCC_Exported_Macros RCC Exported Macros
+ * @{
+ */
+
+/** @defgroup RCC_AHB_Clock_Enable_Disable RCC AHB Clock Enable Disable
+ * @brief Enable or disable the AHB peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+#define __HAL_RCC_GPIOA_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHBENR, RCC_AHBENR_GPIOAEN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_GPIOAEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOB_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHBENR, RCC_AHBENR_GPIOBEN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_GPIOBEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHBENR, RCC_AHBENR_GPIOCEN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_GPIOCEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_GPIOF_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHBENR, RCC_AHBENR_GPIOFEN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_GPIOFEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_CRC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHBENR, RCC_AHBENR_CRCEN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_CRCEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_DMA1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHBENR, RCC_AHBENR_DMA1EN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_DMA1EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SRAM_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHBENR, RCC_AHBENR_SRAMEN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_SRAMEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_FLITF_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHBENR, RCC_AHBENR_FLITFEN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->AHBENR, RCC_AHBENR_FLITFEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_GPIOA_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_GPIOAEN))
+#define __HAL_RCC_GPIOB_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_GPIOBEN))
+#define __HAL_RCC_GPIOC_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_GPIOCEN))
+#define __HAL_RCC_GPIOF_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_GPIOFEN))
+#define __HAL_RCC_CRC_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_CRCEN))
+#define __HAL_RCC_DMA1_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_DMA1EN))
+#define __HAL_RCC_SRAM_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_SRAMEN))
+#define __HAL_RCC_FLITF_CLK_DISABLE() (RCC->AHBENR &= ~(RCC_AHBENR_FLITFEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCC_AHB_Peripheral_Clock_Enable_Disable_Status AHB Peripheral Clock Enable Disable Status
+ * @brief Get the enable or disable status of the AHB peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+#define __HAL_RCC_GPIOA_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_GPIOAEN)) != RESET)
+#define __HAL_RCC_GPIOB_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_GPIOBEN)) != RESET)
+#define __HAL_RCC_GPIOC_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_GPIOCEN)) != RESET)
+#define __HAL_RCC_GPIOF_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_GPIOFEN)) != RESET)
+#define __HAL_RCC_CRC_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_CRCEN)) != RESET)
+#define __HAL_RCC_DMA1_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_DMA1EN)) != RESET)
+#define __HAL_RCC_SRAM_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_SRAMEN)) != RESET)
+#define __HAL_RCC_FLITF_IS_CLK_ENABLED() ((RCC->AHBENR & (RCC_AHBENR_FLITFEN)) != RESET)
+#define __HAL_RCC_GPIOA_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_GPIOAEN)) == RESET)
+#define __HAL_RCC_GPIOB_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_GPIOBEN)) == RESET)
+#define __HAL_RCC_GPIOC_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_GPIOCEN)) == RESET)
+#define __HAL_RCC_GPIOF_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_GPIOFEN)) == RESET)
+#define __HAL_RCC_CRC_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_CRCEN)) == RESET)
+#define __HAL_RCC_DMA1_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_DMA1EN)) == RESET)
+#define __HAL_RCC_SRAM_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_SRAMEN)) == RESET)
+#define __HAL_RCC_FLITF_IS_CLK_DISABLED() ((RCC->AHBENR & (RCC_AHBENR_FLITFEN)) == RESET)
+/**
+ * @}
+ */
+
+/** @defgroup RCC_APB1_Clock_Enable_Disable RCC APB1 Clock Enable Disable
+ * @brief Enable or disable the Low Speed APB (APB1) peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+#define __HAL_RCC_TIM3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM3EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM14_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM14EN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_TIM14EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_WWDG_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_WWDGEN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_WWDGEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_I2C1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C1EN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_I2C1EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_PWR_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR, RCC_APB1ENR_PWREN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->APB1ENR, RCC_APB1ENR_PWREN);\
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_TIM3_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM3EN))
+#define __HAL_RCC_TIM14_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_TIM14EN))
+#define __HAL_RCC_WWDG_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_WWDGEN))
+#define __HAL_RCC_I2C1_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_I2C1EN))
+#define __HAL_RCC_PWR_CLK_DISABLE() (RCC->APB1ENR &= ~(RCC_APB1ENR_PWREN))
+/**
+ * @}
+ */
+
+/** @defgroup RCC_APB1_Peripheral_Clock_Enable_Disable_Status APB1 Peripheral Clock Enable Disable Status
+ * @brief Get the enable or disable status of the APB1 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+#define __HAL_RCC_TIM3_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) != RESET)
+#define __HAL_RCC_TIM14_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM14EN)) != RESET)
+#define __HAL_RCC_WWDG_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_WWDGEN)) != RESET)
+#define __HAL_RCC_I2C1_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C1EN)) != RESET)
+#define __HAL_RCC_PWR_IS_CLK_ENABLED() ((RCC->APB1ENR & (RCC_APB1ENR_PWREN)) != RESET)
+#define __HAL_RCC_TIM3_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM3EN)) == RESET)
+#define __HAL_RCC_TIM14_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_TIM14EN)) == RESET)
+#define __HAL_RCC_WWDG_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_WWDGEN)) == RESET)
+#define __HAL_RCC_I2C1_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_I2C1EN)) == RESET)
+#define __HAL_RCC_PWR_IS_CLK_DISABLED() ((RCC->APB1ENR & (RCC_APB1ENR_PWREN)) == RESET)
+/**
+ * @}
+ */
+
+
+/** @defgroup RCC_APB2_Clock_Enable_Disable RCC APB2 Clock Enable Disable
+ * @brief Enable or disable the High Speed APB (APB2) peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+#define __HAL_RCC_SYSCFG_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_ADC1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC1EN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_ADC1EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_SPI1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM16_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM16EN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM16EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_TIM17_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM17EN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM17EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_USART1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN);\
+ UNUSED(tmpreg); \
+ } while(0)
+#define __HAL_RCC_DBGMCU_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_DBGMCUEN);\
+ /* Delay after an RCC peripheral clock enabling */\
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_DBGMCUEN);\
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_SYSCFG_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SYSCFGEN))
+#define __HAL_RCC_ADC1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_ADC1EN))
+#define __HAL_RCC_TIM1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM1EN))
+#define __HAL_RCC_SPI1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_SPI1EN))
+#define __HAL_RCC_TIM16_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM16EN))
+#define __HAL_RCC_TIM17_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_TIM17EN))
+#define __HAL_RCC_USART1_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_USART1EN))
+#define __HAL_RCC_DBGMCU_CLK_DISABLE() (RCC->APB2ENR &= ~(RCC_APB2ENR_DBGMCUEN))
+/**
+ * @}
+ */
+
+/** @defgroup RCC_APB2_Peripheral_Clock_Enable_Disable_Status APB2 Peripheral Clock Enable Disable Status
+ * @brief Get the enable or disable status of the APB2 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+#define __HAL_RCC_SYSCFG_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SYSCFGEN)) != RESET)
+#define __HAL_RCC_ADC1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC1EN)) != RESET)
+#define __HAL_RCC_TIM1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM1EN)) != RESET)
+#define __HAL_RCC_SPI1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI1EN)) != RESET)
+#define __HAL_RCC_TIM16_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM16EN)) != RESET)
+#define __HAL_RCC_TIM17_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM17EN)) != RESET)
+#define __HAL_RCC_USART1_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART1EN)) != RESET)
+#define __HAL_RCC_DBGMCU_IS_CLK_ENABLED() ((RCC->APB2ENR & (RCC_APB2ENR_DBGMCUEN)) != RESET)
+#define __HAL_RCC_SYSCFG_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SYSCFGEN)) == RESET)
+#define __HAL_RCC_ADC1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_ADC1EN)) == RESET)
+#define __HAL_RCC_TIM1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM1EN)) == RESET)
+#define __HAL_RCC_SPI1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_SPI1EN)) == RESET)
+#define __HAL_RCC_TIM16_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM16EN)) == RESET)
+#define __HAL_RCC_TIM17_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_TIM17EN)) == RESET)
+#define __HAL_RCC_USART1_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_USART1EN)) == RESET)
+#define __HAL_RCC_DBGMCU_IS_CLK_DISABLED() ((RCC->APB2ENR & (RCC_APB2ENR_DBGMCUEN)) == RESET)
+/**
+ * @}
+ */
+
+/** @defgroup RCC_AHB_Force_Release_Reset RCC AHB Force Release Reset
+ * @brief Force or release AHB peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB_FORCE_RESET() (RCC->AHBRSTR = 0xFFFFFFFFU)
+#define __HAL_RCC_GPIOA_FORCE_RESET() (RCC->AHBRSTR |= (RCC_AHBRSTR_GPIOARST))
+#define __HAL_RCC_GPIOB_FORCE_RESET() (RCC->AHBRSTR |= (RCC_AHBRSTR_GPIOBRST))
+#define __HAL_RCC_GPIOC_FORCE_RESET() (RCC->AHBRSTR |= (RCC_AHBRSTR_GPIOCRST))
+#define __HAL_RCC_GPIOF_FORCE_RESET() (RCC->AHBRSTR |= (RCC_AHBRSTR_GPIOFRST))
+
+#define __HAL_RCC_AHB_RELEASE_RESET() (RCC->AHBRSTR = 0x00)
+#define __HAL_RCC_GPIOA_RELEASE_RESET() (RCC->AHBRSTR &= ~(RCC_AHBRSTR_GPIOARST))
+#define __HAL_RCC_GPIOB_RELEASE_RESET() (RCC->AHBRSTR &= ~(RCC_AHBRSTR_GPIOBRST))
+#define __HAL_RCC_GPIOC_RELEASE_RESET() (RCC->AHBRSTR &= ~(RCC_AHBRSTR_GPIOCRST))
+#define __HAL_RCC_GPIOF_RELEASE_RESET() (RCC->AHBRSTR &= ~(RCC_AHBRSTR_GPIOFRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCC_APB1_Force_Release_Reset RCC APB1 Force Release Reset
+ * @brief Force or release APB1 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_APB1_FORCE_RESET() (RCC->APB1RSTR = 0xFFFFFFFFU)
+#define __HAL_RCC_TIM3_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM14_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_TIM14RST))
+#define __HAL_RCC_WWDG_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_WWDGRST))
+#define __HAL_RCC_I2C1_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_I2C1RST))
+#define __HAL_RCC_PWR_FORCE_RESET() (RCC->APB1RSTR |= (RCC_APB1RSTR_PWRRST))
+
+#define __HAL_RCC_APB1_RELEASE_RESET() (RCC->APB1RSTR = 0x00)
+#define __HAL_RCC_TIM3_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM3RST))
+#define __HAL_RCC_TIM14_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_TIM14RST))
+#define __HAL_RCC_WWDG_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_WWDGRST))
+#define __HAL_RCC_I2C1_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_I2C1RST))
+#define __HAL_RCC_PWR_RELEASE_RESET() (RCC->APB1RSTR &= ~(RCC_APB1RSTR_PWRRST))
+/**
+ * @}
+ */
+
+/** @defgroup RCC_APB2_Force_Release_Reset RCC APB2 Force Release Reset
+ * @brief Force or release APB2 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_APB2_FORCE_RESET() (RCC->APB2RSTR = 0xFFFFFFFFU)
+#define __HAL_RCC_SYSCFG_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SYSCFGRST))
+#define __HAL_RCC_ADC1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_ADC1RST))
+#define __HAL_RCC_TIM1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM1RST))
+#define __HAL_RCC_SPI1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_SPI1RST))
+#define __HAL_RCC_USART1_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_USART1RST))
+#define __HAL_RCC_TIM16_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM16RST))
+#define __HAL_RCC_TIM17_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_TIM17RST))
+#define __HAL_RCC_DBGMCU_FORCE_RESET() (RCC->APB2RSTR |= (RCC_APB2RSTR_DBGMCURST))
+
+#define __HAL_RCC_APB2_RELEASE_RESET() (RCC->APB2RSTR = 0x00)
+#define __HAL_RCC_SYSCFG_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SYSCFGRST))
+#define __HAL_RCC_ADC1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_ADC1RST))
+#define __HAL_RCC_TIM1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM1RST))
+#define __HAL_RCC_SPI1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_SPI1RST))
+#define __HAL_RCC_USART1_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_USART1RST))
+#define __HAL_RCC_TIM16_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM16RST))
+#define __HAL_RCC_TIM17_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_TIM17RST))
+#define __HAL_RCC_DBGMCU_RELEASE_RESET() (RCC->APB2RSTR &= ~(RCC_APB2RSTR_DBGMCURST))
+/**
+ * @}
+ */
+/** @defgroup RCC_HSI_Configuration HSI Configuration
+ * @{
+ */
+
+/** @brief Macros to enable or disable the Internal High Speed oscillator (HSI).
+ * @note The HSI is stopped by hardware when entering STOP and STANDBY modes.
+ * @note HSI can not be stopped if it is used as system clock source. In this case,
+ * you have to select another source of the system clock then stop the HSI.
+ * @note After enabling the HSI, the application software should wait on HSIRDY
+ * flag to be set indicating that HSI clock is stable and can be used as
+ * system clock source.
+ * @note When the HSI is stopped, HSIRDY flag goes low after 6 HSI oscillator
+ * clock cycles.
+ */
+#define __HAL_RCC_HSI_ENABLE() SET_BIT(RCC->CR, RCC_CR_HSION)
+#define __HAL_RCC_HSI_DISABLE() CLEAR_BIT(RCC->CR, RCC_CR_HSION)
+
+/** @brief Macro to adjust the Internal High Speed oscillator (HSI) calibration value.
+ * @note The calibration is used to compensate for the variations in voltage
+ * and temperature that influence the frequency of the internal HSI RC.
+ * @param _HSICALIBRATIONVALUE_ specifies the calibration trimming value.
+ * (default is RCC_HSICALIBRATION_DEFAULT).
+ * This parameter must be a number between 0 and 0x1F.
+ */
+#define __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(_HSICALIBRATIONVALUE_) \
+ MODIFY_REG(RCC->CR, RCC_CR_HSITRIM, (uint32_t)(_HSICALIBRATIONVALUE_) << RCC_CR_HSITRIM_BitNumber)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_LSI_Configuration LSI Configuration
+ * @{
+ */
+
+/** @brief Macro to enable the Internal Low Speed oscillator (LSI).
+ * @note After enabling the LSI, the application software should wait on
+ * LSIRDY flag to be set indicating that LSI clock is stable and can
+ * be used to clock the IWDG and/or the RTC.
+ */
+#define __HAL_RCC_LSI_ENABLE() SET_BIT(RCC->CSR, RCC_CSR_LSION)
+
+/** @brief Macro to disable the Internal Low Speed oscillator (LSI).
+ * @note LSI can not be disabled if the IWDG is running.
+ * @note When the LSI is stopped, LSIRDY flag goes low after 6 LSI oscillator
+ * clock cycles.
+ */
+#define __HAL_RCC_LSI_DISABLE() CLEAR_BIT(RCC->CSR, RCC_CSR_LSION)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_HSE_Configuration HSE Configuration
+ * @{
+ */
+
+/**
+ * @brief Macro to configure the External High Speed oscillator (HSE).
+ * @note Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not
+ * supported by this macro. User should request a transition to HSE Off
+ * first and then HSE On or HSE Bypass.
+ * @note After enabling the HSE (RCC_HSE_ON or RCC_HSE_Bypass), the application
+ * software should wait on HSERDY flag to be set indicating that HSE clock
+ * is stable and can be used to clock the PLL and/or system clock.
+ * @note HSE state can not be changed if it is used directly or through the
+ * PLL as system clock. In this case, you have to select another source
+ * of the system clock then change the HSE state (ex. disable it).
+ * @note The HSE is stopped by hardware when entering STOP and STANDBY modes.
+ * @note This function reset the CSSON bit, so if the clock security system(CSS)
+ * was previously enabled you have to enable it again after calling this
+ * function.
+ * @param __STATE__ specifies the new state of the HSE.
+ * This parameter can be one of the following values:
+ * @arg @ref RCC_HSE_OFF turn OFF the HSE oscillator, HSERDY flag goes low after
+ * 6 HSE oscillator clock cycles.
+ * @arg @ref RCC_HSE_ON turn ON the HSE oscillator
+ * @arg @ref RCC_HSE_BYPASS HSE oscillator bypassed with external clock
+ */
+#define __HAL_RCC_HSE_CONFIG(__STATE__) \
+ do{ \
+ if ((__STATE__) == RCC_HSE_ON) \
+ { \
+ SET_BIT(RCC->CR, RCC_CR_HSEON); \
+ } \
+ else if ((__STATE__) == RCC_HSE_OFF) \
+ { \
+ CLEAR_BIT(RCC->CR, RCC_CR_HSEON); \
+ CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP); \
+ } \
+ else if ((__STATE__) == RCC_HSE_BYPASS) \
+ { \
+ SET_BIT(RCC->CR, RCC_CR_HSEBYP); \
+ SET_BIT(RCC->CR, RCC_CR_HSEON); \
+ } \
+ else \
+ { \
+ CLEAR_BIT(RCC->CR, RCC_CR_HSEON); \
+ CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP); \
+ } \
+ }while(0)
+
+/**
+ * @brief Macro to configure the External High Speed oscillator (HSE) Predivision factor for PLL.
+ * @note Predivision factor can not be changed if PLL is used as system clock
+ * In this case, you have to select another source of the system clock, disable the PLL and
+ * then change the HSE predivision factor.
+ * @param __HSE_PREDIV_VALUE__ specifies the division value applied to HSE.
+ * This parameter must be a number between RCC_HSE_PREDIV_DIV1 and RCC_HSE_PREDIV_DIV16.
+ */
+#define __HAL_RCC_HSE_PREDIV_CONFIG(__HSE_PREDIV_VALUE__) \
+ MODIFY_REG(RCC->CFGR2, RCC_CFGR2_PREDIV, (uint32_t)(__HSE_PREDIV_VALUE__))
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_LSE_Configuration LSE Configuration
+ * @{
+ */
+
+/**
+ * @brief Macro to configure the External Low Speed oscillator (LSE).
+ * @note Transitions LSE Bypass to LSE On and LSE On to LSE Bypass are not supported by this macro.
+ * @note As the LSE is in the Backup domain and write access is denied to
+ * this domain after reset, you have to enable write access using
+ * @ref HAL_PWR_EnableBkUpAccess() function before to configure the LSE
+ * (to be done once after reset).
+ * @note After enabling the LSE (RCC_LSE_ON or RCC_LSE_BYPASS), the application
+ * software should wait on LSERDY flag to be set indicating that LSE clock
+ * is stable and can be used to clock the RTC.
+ * @param __STATE__ specifies the new state of the LSE.
+ * This parameter can be one of the following values:
+ * @arg @ref RCC_LSE_OFF turn OFF the LSE oscillator, LSERDY flag goes low after
+ * 6 LSE oscillator clock cycles.
+ * @arg @ref RCC_LSE_ON turn ON the LSE oscillator.
+ * @arg @ref RCC_LSE_BYPASS LSE oscillator bypassed with external clock.
+ */
+#define __HAL_RCC_LSE_CONFIG(__STATE__) \
+ do{ \
+ if ((__STATE__) == RCC_LSE_ON) \
+ { \
+ SET_BIT(RCC->BDCR, RCC_BDCR_LSEON); \
+ } \
+ else if ((__STATE__) == RCC_LSE_OFF) \
+ { \
+ CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEON); \
+ CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEBYP); \
+ } \
+ else if ((__STATE__) == RCC_LSE_BYPASS) \
+ { \
+ SET_BIT(RCC->BDCR, RCC_BDCR_LSEBYP); \
+ SET_BIT(RCC->BDCR, RCC_BDCR_LSEON); \
+ } \
+ else \
+ { \
+ CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEON); \
+ CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEBYP); \
+ } \
+ }while(0)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_HSI14_Configuration RCC_HSI14_Configuration
+ * @{
+ */
+
+/** @brief Macro to enable the Internal 14Mhz High Speed oscillator (HSI14).
+ * @note After enabling the HSI14 with @ref __HAL_RCC_HSI14_ENABLE(), the application software
+ * should wait on HSI14RDY flag to be set indicating that HSI clock is stable and can be
+ * used as system clock source. This is not necessary if @ref HAL_RCC_OscConfig() is used.
+ * clock cycles.
+ */
+#define __HAL_RCC_HSI14_ENABLE() SET_BIT(RCC->CR2, RCC_CR2_HSI14ON)
+
+/** @brief Macro to disable the Internal 14Mhz High Speed oscillator (HSI14).
+ * @note The HSI14 is stopped by hardware when entering STOP and STANDBY modes.
+ * @note HSI14 can not be stopped if it is used as system clock source. In this case,
+ * you have to select another source of the system clock then stop the HSI14.
+ * @note When the HSI14 is stopped, HSI14RDY flag goes low after 6 HSI14 oscillator
+ * clock cycles.
+ */
+#define __HAL_RCC_HSI14_DISABLE() CLEAR_BIT(RCC->CR2, RCC_CR2_HSI14ON)
+
+/** @brief Macro to enable the Internal 14Mhz High Speed oscillator (HSI14) used by ADC.
+ */
+#define __HAL_RCC_HSI14ADC_ENABLE() CLEAR_BIT(RCC->CR2, RCC_CR2_HSI14DIS)
+
+/** @brief Macro to disable the Internal 14Mhz High Speed oscillator (HSI14) used by ADC.
+ */
+#define __HAL_RCC_HSI14ADC_DISABLE() SET_BIT(RCC->CR2, RCC_CR2_HSI14DIS)
+
+/** @brief Macro to adjust the Internal 14Mhz High Speed oscillator (HSI) calibration value.
+ * @note The calibration is used to compensate for the variations in voltage
+ * and temperature that influence the frequency of the internal HSI14 RC.
+ * @param __HSI14CALIBRATIONVALUE__ specifies the calibration trimming value
+ * (default is RCC_HSI14CALIBRATION_DEFAULT).
+ * This parameter must be a number between 0 and 0x1F.
+ */
+#define __HAL_RCC_HSI14_CALIBRATIONVALUE_ADJUST(__HSI14CALIBRATIONVALUE__) \
+ MODIFY_REG(RCC->CR2, RCC_CR2_HSI14TRIM, (uint32_t)(__HSI14CALIBRATIONVALUE__) << RCC_HSI14TRIM_BIT_NUMBER)
+/**
+ * @}
+ */
+
+/** @defgroup RCC_USARTx_Clock_Config RCC USARTx Clock Config
+ * @{
+ */
+
+/** @brief Macro to configure the USART1 clock (USART1CLK).
+ * @param __USART1CLKSOURCE__ specifies the USART1 clock source.
+ * This parameter can be one of the following values:
+ * @arg @ref RCC_USART1CLKSOURCE_PCLK1 PCLK1 selected as USART1 clock
+ * @arg @ref RCC_USART1CLKSOURCE_HSI HSI selected as USART1 clock
+ * @arg @ref RCC_USART1CLKSOURCE_SYSCLK System Clock selected as USART1 clock
+ * @arg @ref RCC_USART1CLKSOURCE_LSE LSE selected as USART1 clock
+ */
+#define __HAL_RCC_USART1_CONFIG(__USART1CLKSOURCE__) \
+ MODIFY_REG(RCC->CFGR3, RCC_CFGR3_USART1SW, (uint32_t)(__USART1CLKSOURCE__))
+
+/** @brief Macro to get the USART1 clock source.
+ * @retval The clock source can be one of the following values:
+ * @arg @ref RCC_USART1CLKSOURCE_PCLK1 PCLK1 selected as USART1 clock
+ * @arg @ref RCC_USART1CLKSOURCE_HSI HSI selected as USART1 clock
+ * @arg @ref RCC_USART1CLKSOURCE_SYSCLK System Clock selected as USART1 clock
+ * @arg @ref RCC_USART1CLKSOURCE_LSE LSE selected as USART1 clock
+ */
+#define __HAL_RCC_GET_USART1_SOURCE() ((uint32_t)(READ_BIT(RCC->CFGR3, RCC_CFGR3_USART1SW)))
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_I2Cx_Clock_Config RCC I2Cx Clock Config
+ * @{
+ */
+
+/** @brief Macro to configure the I2C1 clock (I2C1CLK).
+ * @param __I2C1CLKSOURCE__ specifies the I2C1 clock source.
+ * This parameter can be one of the following values:
+ * @arg @ref RCC_I2C1CLKSOURCE_HSI HSI selected as I2C1 clock
+ * @arg @ref RCC_I2C1CLKSOURCE_SYSCLK System Clock selected as I2C1 clock
+ */
+#define __HAL_RCC_I2C1_CONFIG(__I2C1CLKSOURCE__) \
+ MODIFY_REG(RCC->CFGR3, RCC_CFGR3_I2C1SW, (uint32_t)(__I2C1CLKSOURCE__))
+
+/** @brief Macro to get the I2C1 clock source.
+ * @retval The clock source can be one of the following values:
+ * @arg @ref RCC_I2C1CLKSOURCE_HSI HSI selected as I2C1 clock
+ * @arg @ref RCC_I2C1CLKSOURCE_SYSCLK System Clock selected as I2C1 clock
+ */
+#define __HAL_RCC_GET_I2C1_SOURCE() ((uint32_t)(READ_BIT(RCC->CFGR3, RCC_CFGR3_I2C1SW)))
+/**
+ * @}
+ */
+
+/** @defgroup RCC_PLL_Configuration PLL Configuration
+ * @{
+ */
+
+/** @brief Macro to enable the main PLL.
+ * @note After enabling the main PLL, the application software should wait on
+ * PLLRDY flag to be set indicating that PLL clock is stable and can
+ * be used as system clock source.
+ * @note The main PLL is disabled by hardware when entering STOP and STANDBY modes.
+ */
+#define __HAL_RCC_PLL_ENABLE() SET_BIT(RCC->CR, RCC_CR_PLLON)
+
+/** @brief Macro to disable the main PLL.
+ * @note The main PLL can not be disabled if it is used as system clock source
+ */
+#define __HAL_RCC_PLL_DISABLE() CLEAR_BIT(RCC->CR, RCC_CR_PLLON)
+
+/** @brief Macro to configure the PLL clock source, multiplication and division factors.
+ * @note This function must be used only when the main PLL is disabled.
+ *
+ * @param __RCC_PLLSOURCE__ specifies the PLL entry clock source.
+ * This parameter can be one of the following values:
+ * @arg @ref RCC_PLLSOURCE_HSI HSI oscillator clock selected as PLL clock entry
+ * @arg @ref RCC_PLLSOURCE_HSE HSE oscillator clock selected as PLL clock entry
+ * @param __PLLMUL__ specifies the multiplication factor for PLL VCO output clock
+ * This parameter can be one of the following values:
+ * This parameter must be a number between RCC_PLL_MUL2 and RCC_PLL_MUL16.
+ * @param __PREDIV__ specifies the predivider factor for PLL VCO input clock
+ * This parameter must be a number between RCC_PREDIV_DIV1 and RCC_PREDIV_DIV16.
+ *
+ */
+#define __HAL_RCC_PLL_CONFIG(__RCC_PLLSOURCE__ , __PREDIV__, __PLLMUL__) \
+ do { \
+ MODIFY_REG(RCC->CFGR2, RCC_CFGR2_PREDIV, (__PREDIV__)); \
+ MODIFY_REG(RCC->CFGR, RCC_CFGR_PLLMUL | RCC_CFGR_PLLSRC, (uint32_t)((__PLLMUL__)|(__RCC_PLLSOURCE__))); \
+ } while(0)
+
+
+/** @brief Get oscillator clock selected as PLL input clock
+ * @retval The clock source used for PLL entry. The returned value can be one
+ * of the following:
+ * @arg @ref RCC_PLLSOURCE_HSE HSE oscillator clock selected as PLL input clock
+ */
+#define __HAL_RCC_GET_PLL_OSCSOURCE() ((uint32_t)(READ_BIT(RCC->CFGR, RCC_CFGR_PLLSRC)))
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_Get_Clock_source Get Clock source
+ * @{
+ */
+
+/**
+ * @brief Macro to configure the system clock source.
+ * @param __SYSCLKSOURCE__ specifies the system clock source.
+ * This parameter can be one of the following values:
+ * @arg @ref RCC_SYSCLKSOURCE_HSI HSI oscillator is used as system clock source.
+ * @arg @ref RCC_SYSCLKSOURCE_HSE HSE oscillator is used as system clock source.
+ * @arg @ref RCC_SYSCLKSOURCE_PLLCLK PLL output is used as system clock source.
+ */
+#define __HAL_RCC_SYSCLK_CONFIG(__SYSCLKSOURCE__) \
+ MODIFY_REG(RCC->CFGR, RCC_CFGR_SW, (__SYSCLKSOURCE__))
+
+/** @brief Macro to get the clock source used as system clock.
+ * @retval The clock source used as system clock. The returned value can be one
+ * of the following:
+ * @arg @ref RCC_SYSCLKSOURCE_STATUS_HSI HSI used as system clock
+ * @arg @ref RCC_SYSCLKSOURCE_STATUS_HSE HSE used as system clock
+ * @arg @ref RCC_SYSCLKSOURCE_STATUS_PLLCLK PLL used as system clock
+ */
+#define __HAL_RCC_GET_SYSCLK_SOURCE() ((uint32_t)(READ_BIT(RCC->CFGR,RCC_CFGR_SWS)))
+
+/**
+ * @}
+ */
+
+/** @defgroup RCCEx_MCOx_Clock_Config RCC Extended MCOx Clock Config
+ * @{
+ */
+
+#if defined(RCC_CFGR_MCOPRE)
+/** @brief Macro to configure the MCO clock.
+ * @param __MCOCLKSOURCE__ specifies the MCO clock source.
+ * This parameter can be one of the following values:
+ * @arg @ref RCC_MCO1SOURCE_NOCLOCK No clock selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_SYSCLK System Clock selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_HSI HSI oscillator clock selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_HSE HSE selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_LSI LSI selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_LSE LSE selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_HSI14 HSI14 selected as MCO clock
+ @if STM32F042x6
+ * @arg @ref RCC_MCO1SOURCE_HSI48 HSI48 selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_PLLCLK PLLCLK selected as MCO clock
+ @elseif STM32F048xx
+ * @arg @ref RCC_MCO1SOURCE_HSI48 HSI48 selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_PLLCLK PLLCLK selected as MCO clock
+ @elseif STM32F071xB
+ * @arg @ref RCC_MCO1SOURCE_HSI48 HSI48 selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_PLLCLK PLLCLK selected as MCO clock
+ @elseif STM32F072xB
+ * @arg @ref RCC_MCO1SOURCE_HSI48 HSI48 selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_PLLCLK PLLCLK selected as MCO clock
+ @elseif STM32F078xx
+ * @arg @ref RCC_MCO1SOURCE_HSI48 HSI48 selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_PLLCLK PLLCLK selected as MCO clock
+ @elseif STM32F091xC
+ * @arg @ref RCC_MCO1SOURCE_HSI48 HSI48 selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_PLLCLK PLLCLK selected as MCO clock
+ @elseif STM32F098xx
+ * @arg @ref RCC_MCO1SOURCE_HSI48 HSI48 selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_PLLCLK PLLCLK selected as MCO clock
+ @elseif STM32F030x6
+ * @arg @ref RCC_MCO1SOURCE_PLLCLK PLLCLK selected as MCO clock
+ @elseif STM32F030xC
+ * @arg @ref RCC_MCO1SOURCE_PLLCLK PLLCLK selected as MCO clock
+ @elseif STM32F031x6
+ * @arg @ref RCC_MCO1SOURCE_PLLCLK PLLCLK selected as MCO clock
+ @elseif STM32F038xx
+ * @arg @ref RCC_MCO1SOURCE_PLLCLK PLLCLK selected as MCO clock
+ @elseif STM32F070x6
+ * @arg @ref RCC_MCO1SOURCE_PLLCLK PLLCLK selected as MCO clock
+ @elseif STM32F070xB
+ * @arg @ref RCC_MCO1SOURCE_PLLCLK PLLCLK selected as MCO clock
+ @endif
+ * @arg @ref RCC_MCO1SOURCE_PLLCLK_DIV2 PLLCLK Divided by 2 selected as MCO clock
+ * @param __MCODIV__ specifies the MCO clock prescaler.
+ * This parameter can be one of the following values:
+ * @arg @ref RCC_MCODIV_1 MCO clock source is divided by 1
+ * @arg @ref RCC_MCODIV_2 MCO clock source is divided by 2
+ * @arg @ref RCC_MCODIV_4 MCO clock source is divided by 4
+ * @arg @ref RCC_MCODIV_8 MCO clock source is divided by 8
+ * @arg @ref RCC_MCODIV_16 MCO clock source is divided by 16
+ * @arg @ref RCC_MCODIV_32 MCO clock source is divided by 32
+ * @arg @ref RCC_MCODIV_64 MCO clock source is divided by 64
+ * @arg @ref RCC_MCODIV_128 MCO clock source is divided by 128
+ */
+#else
+/** @brief Macro to configure the MCO clock.
+ * @param __MCOCLKSOURCE__ specifies the MCO clock source.
+ * This parameter can be one of the following values:
+ * @arg @ref RCC_MCO1SOURCE_NOCLOCK No clock selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_SYSCLK System Clock selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_HSI HSI selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_HSE HSE selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_LSI LSI selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_LSE LSE selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_HSI14 HSI14 selected as MCO clock
+ * @arg @ref RCC_MCO1SOURCE_PLLCLK_DIV2 PLLCLK Divided by 2 selected as MCO clock
+ * @param __MCODIV__ specifies the MCO clock prescaler.
+ * This parameter can be one of the following values:
+ * @arg @ref RCC_MCODIV_1 No division applied on MCO clock source
+ */
+#endif
+#if defined(RCC_CFGR_MCOPRE)
+#define __HAL_RCC_MCO1_CONFIG(__MCOCLKSOURCE__, __MCODIV__) \
+ MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO | RCC_CFGR_MCOPRE), ((__MCOCLKSOURCE__) | (__MCODIV__)))
+#else
+
+#define __HAL_RCC_MCO1_CONFIG(__MCOCLKSOURCE__, __MCODIV__) \
+ MODIFY_REG(RCC->CFGR, RCC_CFGR_MCO, (__MCOCLKSOURCE__))
+
+#endif
+
+/**
+ * @}
+ */
+
+ /** @defgroup RCC_RTC_Clock_Configuration RCC RTC Clock Configuration
+ * @{
+ */
+
+/** @brief Macro to configure the RTC clock (RTCCLK).
+ * @note As the RTC clock configuration bits are in the Backup domain and write
+ * access is denied to this domain after reset, you have to enable write
+ * access using the Power Backup Access macro before to configure
+ * the RTC clock source (to be done once after reset).
+ * @note Once the RTC clock is configured it can't be changed unless the
+ * Backup domain is reset using @ref __HAL_RCC_BACKUPRESET_FORCE() macro, or by
+ * a Power On Reset (POR).
+ *
+ * @param __RTC_CLKSOURCE__ specifies the RTC clock source.
+ * This parameter can be one of the following values:
+ * @arg @ref RCC_RTCCLKSOURCE_NO_CLK No clock selected as RTC clock
+ * @arg @ref RCC_RTCCLKSOURCE_LSE LSE selected as RTC clock
+ * @arg @ref RCC_RTCCLKSOURCE_LSI LSI selected as RTC clock
+ * @arg @ref RCC_RTCCLKSOURCE_HSE_DIV32 HSE clock divided by 32
+ * @note If the LSE or LSI is used as RTC clock source, the RTC continues to
+ * work in STOP and STANDBY modes, and can be used as wakeup source.
+ * However, when the LSI clock and HSE clock divided by 32 is used as RTC clock source,
+ * the RTC cannot be used in STOP and STANDBY modes.
+ * @note The system must always be configured so as to get a PCLK frequency greater than or
+ * equal to the RTCCLK frequency for a proper operation of the RTC.
+ */
+#define __HAL_RCC_RTC_CONFIG(__RTC_CLKSOURCE__) MODIFY_REG(RCC->BDCR, RCC_BDCR_RTCSEL, (__RTC_CLKSOURCE__))
+
+/** @brief Macro to get the RTC clock source.
+ * @retval The clock source can be one of the following values:
+ * @arg @ref RCC_RTCCLKSOURCE_NO_CLK No clock selected as RTC clock
+ * @arg @ref RCC_RTCCLKSOURCE_LSE LSE selected as RTC clock
+ * @arg @ref RCC_RTCCLKSOURCE_LSI LSI selected as RTC clock
+ * @arg @ref RCC_RTCCLKSOURCE_HSE_DIV32 HSE clock divided by 32
+ */
+#define __HAL_RCC_GET_RTC_SOURCE() (READ_BIT(RCC->BDCR, RCC_BDCR_RTCSEL))
+
+/** @brief Macro to enable the the RTC clock.
+ * @note These macros must be used only after the RTC clock source was selected.
+ */
+#define __HAL_RCC_RTC_ENABLE() SET_BIT(RCC->BDCR, RCC_BDCR_RTCEN)
+
+/** @brief Macro to disable the the RTC clock.
+ * @note These macros must be used only after the RTC clock source was selected.
+ */
+#define __HAL_RCC_RTC_DISABLE() CLEAR_BIT(RCC->BDCR, RCC_BDCR_RTCEN)
+
+/** @brief Macro to force the Backup domain reset.
+ * @note This function resets the RTC peripheral (including the backup registers)
+ * and the RTC clock source selection in RCC_BDCR register.
+ */
+#define __HAL_RCC_BACKUPRESET_FORCE() SET_BIT(RCC->BDCR, RCC_BDCR_BDRST)
+
+/** @brief Macros to release the Backup domain reset.
+ */
+#define __HAL_RCC_BACKUPRESET_RELEASE() CLEAR_BIT(RCC->BDCR, RCC_BDCR_BDRST)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_Flags_Interrupts_Management Flags Interrupts Management
+ * @brief macros to manage the specified RCC Flags and interrupts.
+ * @{
+ */
+
+/** @brief Enable RCC interrupt.
+ * @param __INTERRUPT__ specifies the RCC interrupt sources to be enabled.
+ * This parameter can be any combination of the following values:
+ * @arg @ref RCC_IT_LSIRDY LSI ready interrupt
+ * @arg @ref RCC_IT_LSERDY LSE ready interrupt
+ * @arg @ref RCC_IT_HSIRDY HSI ready interrupt
+ * @arg @ref RCC_IT_HSERDY HSE ready interrupt
+ * @arg @ref RCC_IT_PLLRDY main PLL ready interrupt
+ * @arg @ref RCC_IT_HSI14RDY HSI14 ready interrupt
+ @if STM32F042x6
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F048xx
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F071xB
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F072xB
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F078xx
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F091xC
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F098xx
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @endif
+ */
+#define __HAL_RCC_ENABLE_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE1_ADDRESS |= (__INTERRUPT__))
+
+/** @brief Disable RCC interrupt.
+ * @param __INTERRUPT__ specifies the RCC interrupt sources to be disabled.
+ * This parameter can be any combination of the following values:
+ * @arg @ref RCC_IT_LSIRDY LSI ready interrupt
+ * @arg @ref RCC_IT_LSERDY LSE ready interrupt
+ * @arg @ref RCC_IT_HSIRDY HSI ready interrupt
+ * @arg @ref RCC_IT_HSERDY HSE ready interrupt
+ * @arg @ref RCC_IT_PLLRDY main PLL ready interrupt
+ * @arg @ref RCC_IT_HSI14RDY HSI14 ready interrupt
+ @if STM32F042x6
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F048xx
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F071xB
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F072xB
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F078xx
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F091xC
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F098xx
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @endif
+ */
+#define __HAL_RCC_DISABLE_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE1_ADDRESS &= (uint8_t)(~(__INTERRUPT__)))
+
+/** @brief Clear the RCC's interrupt pending bits.
+ * @param __INTERRUPT__ specifies the interrupt pending bit to clear.
+ * This parameter can be any combination of the following values:
+ * @arg @ref RCC_IT_LSIRDY LSI ready interrupt.
+ * @arg @ref RCC_IT_LSERDY LSE ready interrupt.
+ * @arg @ref RCC_IT_HSIRDY HSI ready interrupt.
+ * @arg @ref RCC_IT_HSERDY HSE ready interrupt.
+ * @arg @ref RCC_IT_PLLRDY Main PLL ready interrupt.
+ * @arg @ref RCC_IT_CSS Clock Security System interrupt
+ * @arg @ref RCC_IT_HSI14RDY HSI14 ready interrupt
+ @if STM32F042x6
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F048xx
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F071xB
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F072xB
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F078xx
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F091xC
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F098xx
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @endif
+ */
+#define __HAL_RCC_CLEAR_IT(__INTERRUPT__) (*(__IO uint8_t *) RCC_CIR_BYTE2_ADDRESS = (__INTERRUPT__))
+
+/** @brief Check the RCC's interrupt has occurred or not.
+ * @param __INTERRUPT__ specifies the RCC interrupt source to check.
+ * This parameter can be one of the following values:
+ * @arg @ref RCC_IT_LSIRDY LSI ready interrupt.
+ * @arg @ref RCC_IT_LSERDY LSE ready interrupt.
+ * @arg @ref RCC_IT_HSIRDY HSI ready interrupt.
+ * @arg @ref RCC_IT_HSERDY HSE ready interrupt.
+ * @arg @ref RCC_IT_PLLRDY Main PLL ready interrupt.
+ * @arg @ref RCC_IT_CSS Clock Security System interrupt
+ * @arg @ref RCC_IT_HSI14RDY HSI14 ready interrupt enable
+ @if STM32F042x6
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F048xx
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F071xB
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F072xB
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F078xx
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F091xC
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @elseif STM32F098xx
+ * @arg @ref RCC_IT_HSI48RDY HSI48 ready interrupt
+ @endif
+ * @retval The new state of __INTERRUPT__ (TRUE or FALSE).
+ */
+#define __HAL_RCC_GET_IT(__INTERRUPT__) ((RCC->CIR & (__INTERRUPT__)) == (__INTERRUPT__))
+
+/** @brief Set RMVF bit to clear the reset flags.
+ * The reset flags are RCC_FLAG_PINRST, RCC_FLAG_PORRST, RCC_FLAG_SFTRST,
+ * RCC_FLAG_OBLRST, RCC_FLAG_IWDGRST, RCC_FLAG_WWDGRST, RCC_FLAG_LPWRRST
+ */
+#define __HAL_RCC_CLEAR_RESET_FLAGS() (RCC->CSR |= RCC_CSR_RMVF)
+
+/** @brief Check RCC flag is set or not.
+ * @param __FLAG__ specifies the flag to check.
+ * This parameter can be one of the following values:
+ * @arg @ref RCC_FLAG_HSIRDY HSI oscillator clock ready.
+ * @arg @ref RCC_FLAG_HSERDY HSE oscillator clock ready.
+ * @arg @ref RCC_FLAG_PLLRDY Main PLL clock ready.
+ * @arg @ref RCC_FLAG_HSI14RDY HSI14 oscillator clock ready
+ @if STM32F038xx
+ * @arg @ref RCC_FLAG_V18PWRRST Reset flag of the 1.8 V domain
+ @elseif STM32F042x6
+ * @arg @ref RCC_FLAG_HSI48RDY HSI48 oscillator clock ready
+ @elseif STM32F048xx
+ * @arg @ref RCC_FLAG_HSI48RDY HSI48 oscillator clock ready
+ * @arg @ref RCC_FLAG_V18PWRRST Reset flag of the 1.8 V domain
+ @elseif STM32F058xx
+ * @arg @ref RCC_FLAG_V18PWRRST Reset flag of the 1.8 V domain
+ @elseif STM32F071xB
+ * @arg @ref RCC_FLAG_HSI48RDY HSI48 oscillator clock ready
+ @elseif STM32F072xB
+ * @arg @ref RCC_FLAG_HSI48RDY HSI48 oscillator clock ready
+ @elseif STM32F078xx
+ * @arg @ref RCC_FLAG_HSI48RDY HSI48 oscillator clock ready
+ * @arg @ref RCC_FLAG_V18PWRRST Reset flag of the 1.8 V domain
+ @elseif STM32F091xC
+ * @arg @ref RCC_FLAG_HSI48RDY HSI48 oscillator clock ready
+ @elseif STM32F098xx
+ * @arg @ref RCC_FLAG_HSI48RDY HSI48 oscillator clock ready
+ * @arg @ref RCC_FLAG_V18PWRRST Reset flag of the 1.8 V domain
+ @endif
+ * @arg @ref RCC_FLAG_LSERDY LSE oscillator clock ready.
+ * @arg @ref RCC_FLAG_LSIRDY LSI oscillator clock ready.
+ * @arg @ref RCC_FLAG_OBLRST Option Byte Load reset
+ * @arg @ref RCC_FLAG_PINRST Pin reset.
+ * @arg @ref RCC_FLAG_PORRST POR/PDR reset.
+ * @arg @ref RCC_FLAG_SFTRST Software reset.
+ * @arg @ref RCC_FLAG_IWDGRST Independent Watchdog reset.
+ * @arg @ref RCC_FLAG_WWDGRST Window Watchdog reset.
+ * @arg @ref RCC_FLAG_LPWRRST Low Power reset.
+ * @retval The new state of __FLAG__ (TRUE or FALSE).
+ */
+#define __HAL_RCC_GET_FLAG(__FLAG__) (((((__FLAG__) >> 5) == CR_REG_INDEX)? RCC->CR : \
+ (((__FLAG__) >> 5) == CR2_REG_INDEX)? RCC->CR2 : \
+ (((__FLAG__) >> 5) == BDCR_REG_INDEX) ? RCC->BDCR : \
+ RCC->CSR) & ((uint32_t)1 << ((__FLAG__) & RCC_FLAG_MASK)))
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/* Include RCC HAL Extension module */
+#include "stm32f0xx_hal_rcc_ex.h"
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup RCC_Exported_Functions
+ * @{
+ */
+
+/** @addtogroup RCC_Exported_Functions_Group1
+ * @{
+ */
+
+/* Initialization and de-initialization functions ******************************/
+void HAL_RCC_DeInit(void);
+HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct);
+HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t FLatency);
+
+/**
+ * @}
+ */
+
+/** @addtogroup RCC_Exported_Functions_Group2
+ * @{
+ */
+
+/* Peripheral Control functions ************************************************/
+void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv);
+void HAL_RCC_EnableCSS(void);
+void HAL_RCC_DisableCSS(void);
+uint32_t HAL_RCC_GetSysClockFreq(void);
+uint32_t HAL_RCC_GetHCLKFreq(void);
+uint32_t HAL_RCC_GetPCLK1Freq(void);
+void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct);
+void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t *pFLatency);
+
+/* CSS NMI IRQ handler */
+void HAL_RCC_NMI_IRQHandler(void);
+
+/* User Callbacks in non blocking mode (IT mode) */
+void HAL_RCC_CSSCallback(void);
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32F0xx_HAL_RCC_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
+
