Thomas Lyp
Initial commit
Diff: mbed-dev-master/targets/TARGET_STM/TARGET_STM32F4/device/stm32f4xx_hal_rcc.c
- Revision:
- 0:bb348c97df44
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-dev-master/targets/TARGET_STM/TARGET_STM32F4/device/stm32f4xx_hal_rcc.c Wed Sep 16 01:11:49 2020 +0000
@@ -0,0 +1,1113 @@
+/**
+ ******************************************************************************
+ * @file stm32f4xx_hal_rcc.c
+ * @author MCD Application Team
+ * @brief RCC HAL module driver.
+ * This file provides firmware functions to manage the following
+ * functionalities of the Reset and Clock Control (RCC) peripheral:
+ * + Initialization and de-initialization functions
+ * + Peripheral Control functions
+ *
+ @verbatim
+ ==============================================================================
+ ##### RCC specific features #####
+ ==============================================================================
+ [..]
+ After reset the device is running from Internal High Speed oscillator
+ (HSI 16MHz) with Flash 0 wait state, Flash prefetch buffer, D-Cache
+ and I-Cache are disabled, and all peripherals are off except internal
+ SRAM, Flash and JTAG.
+ (+) There is no prescaler on High speed (AHB) and Low speed (APB) busses;
+ all peripherals mapped on these busses are running at HSI speed.
+ (+) The clock for all peripherals is switched off, except the SRAM and FLASH.
+ (+) All GPIOs are in input floating state, except the JTAG pins which
+ are assigned to be used for debug purpose.
+
+ [..]
+ Once the device started from reset, the user application has to:
+ (+) Configure the clock source to be used to drive the System clock
+ (if the application needs higher frequency/performance)
+ (+) Configure the System clock frequency and Flash settings
+ (+) Configure the AHB and APB busses prescalers
+ (+) Enable the clock for the peripheral(s) to be used
+ (+) Configure the clock source(s) for peripherals which clocks are not
+ derived from the System clock (I2S, RTC, ADC, USB OTG FS/SDIO/RNG)
+
+ ##### RCC Limitations #####
+ ==============================================================================
+ [..]
+ A delay between an RCC peripheral clock enable and the effective peripheral
+ enabling should be taken into account in order to manage the peripheral read/write
+ from/to registers.
+ (+) This delay depends on the peripheral mapping.
+ (+) If peripheral is mapped on AHB: the delay is 2 AHB clock cycle
+ after the clock enable bit is set on the hardware register
+ (+) If peripheral is mapped on APB: the delay is 2 APB clock cycle
+ after the clock enable bit is set on the hardware register
+
+ [..]
+ Implemented Workaround:
+ (+) For AHB & APB peripherals, a dummy read to the peripheral register has been
+ inserted in each __HAL_RCC_PPP_CLK_ENABLE() macro.
+
+ @endverbatim
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2017 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32f4xx_hal.h"
+
+/** @addtogroup STM32F4xx_HAL_Driver
+ * @{
+ */
+
+/** @defgroup RCC RCC
+ * @brief RCC HAL module driver
+ * @{
+ */
+
+#ifdef HAL_RCC_MODULE_ENABLED
+
+/* Private typedef -----------------------------------------------------------*/
+/* Private define ------------------------------------------------------------*/
+/** @addtogroup RCC_Private_Constants
+ * @{
+ */
+
+/* Private macro -------------------------------------------------------------*/
+#define __MCO1_CLK_ENABLE() __HAL_RCC_GPIOA_CLK_ENABLE()
+#define MCO1_GPIO_PORT GPIOA
+#define MCO1_PIN GPIO_PIN_8
+
+#define __MCO2_CLK_ENABLE() __HAL_RCC_GPIOC_CLK_ENABLE()
+#define MCO2_GPIO_PORT GPIOC
+#define MCO2_PIN GPIO_PIN_9
+/**
+ * @}
+ */
+
+/* Private variables ---------------------------------------------------------*/
+/** @defgroup RCC_Private_Variables RCC Private Variables
+ * @{
+ */
+/**
+ * @}
+ */
+/* Private function prototypes -----------------------------------------------*/
+/* Private functions ---------------------------------------------------------*/
+
+/** @defgroup RCC_Exported_Functions RCC Exported Functions
+ * @{
+ */
+
+/** @defgroup RCC_Exported_Functions_Group1 Initialization and de-initialization functions
+ * @brief Initialization and Configuration functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Initialization and de-initialization functions #####
+ ===============================================================================
+ [..]
+ This section provides functions allowing to configure the internal/external oscillators
+ (HSE, HSI, LSE, LSI, PLL, CSS and MCO) and the System busses clocks (SYSCLK, AHB, APB1
+ and APB2).
+
+ [..] Internal/external clock and PLL configuration
+ (#) HSI (high-speed internal), 16 MHz factory-trimmed RC used directly or through
+ the PLL as System clock source.
+
+ (#) LSI (low-speed internal), 32 KHz low consumption RC used as IWDG and/or RTC
+ clock source.
+
+ (#) HSE (high-speed external), 4 to 26 MHz crystal oscillator used directly or
+ through the PLL as System clock source. Can be used also as RTC clock source.
+
+ (#) LSE (low-speed external), 32 KHz oscillator used as RTC clock source.
+
+ (#) PLL (clocked by HSI or HSE), featuring two different output clocks:
+ (++) The first output is used to generate the high speed system clock (up to 168 MHz)
+ (++) The second output is used to generate the clock for the USB OTG FS (48 MHz),
+ the random analog generator (<=48 MHz) and the SDIO (<= 48 MHz).
+
+ (#) CSS (Clock security system), once enable using the macro __HAL_RCC_CSS_ENABLE()
+ and if a HSE clock failure occurs(HSE used directly or through PLL as System
+ clock source), the System clocks automatically switched to HSI and an interrupt
+ is generated if enabled. The interrupt is linked to the Cortex-M4 NMI
+ (Non-Maskable Interrupt) exception vector.
+
+ (#) MCO1 (microcontroller clock output), used to output HSI, LSE, HSE or PLL
+ clock (through a configurable prescaler) on PA8 pin.
+
+ (#) MCO2 (microcontroller clock output), used to output HSE, PLL, SYSCLK or PLLI2S
+ clock (through a configurable prescaler) on PC9 pin.
+
+ [..] System, AHB and APB busses clocks configuration
+ (#) Several clock sources can be used to drive the System clock (SYSCLK): HSI,
+ HSE and PLL.
+ The AHB clock (HCLK) is derived from System clock through configurable
+ prescaler and used to clock the CPU, memory and peripherals mapped
+ on AHB bus (DMA, GPIO...). APB1 (PCLK1) and APB2 (PCLK2) clocks are derived
+ from AHB clock through configurable prescalers and used to clock
+ the peripherals mapped on these busses. You can use
+ "HAL_RCC_GetSysClockFreq()" function to retrieve the frequencies of these clocks.
+
+ (#) For the STM32F405xx/07xx and STM32F415xx/17xx devices, the maximum
+ frequency of the SYSCLK and HCLK is 168 MHz, PCLK2 84 MHz and PCLK1 42 MHz.
+ Depending on the device voltage range, the maximum frequency should
+ be adapted accordingly (refer to the product datasheets for more details).
+
+ (#) For the STM32F42xxx, STM32F43xxx, STM32F446xx, STM32F469xx and STM32F479xx devices,
+ the maximum frequency of the SYSCLK and HCLK is 180 MHz, PCLK2 90 MHz and PCLK1 45 MHz.
+ Depending on the device voltage range, the maximum frequency should
+ be adapted accordingly (refer to the product datasheets for more details).
+
+ (#) For the STM32F401xx, the maximum frequency of the SYSCLK and HCLK is 84 MHz,
+ PCLK2 84 MHz and PCLK1 42 MHz.
+ Depending on the device voltage range, the maximum frequency should
+ be adapted accordingly (refer to the product datasheets for more details).
+
+ (#) For the STM32F41xxx, the maximum frequency of the SYSCLK and HCLK is 100 MHz,
+ PCLK2 100 MHz and PCLK1 50 MHz.
+ Depending on the device voltage range, the maximum frequency should
+ be adapted accordingly (refer to the product datasheets for more details).
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Resets the RCC clock configuration to the default reset state.
+ * @note The default reset state of the clock configuration is given below:
+ * - HSI ON and used as system clock source
+ * - HSE and PLL OFF
+ * - AHB, APB1 and APB2 prescaler set to 1.
+ * - CSS, MCO1 and MCO2 OFF
+ * - All interrupts disabled
+ * @note This function doesn't modify the configuration of the
+ * - Peripheral clocks
+ * - LSI, LSE and RTC clocks
+ * @retval HAL status
+ */
+__weak HAL_StatusTypeDef HAL_RCC_DeInit(void)
+{
+ return HAL_OK;
+}
+
+/**
+ * @brief Initializes the RCC Oscillators according to the specified parameters in the
+ * RCC_OscInitTypeDef.
+ * @param RCC_OscInitStruct pointer to an RCC_OscInitTypeDef structure that
+ * contains the configuration information for the RCC Oscillators.
+ * @note The PLL is not disabled when used as system clock.
+ * @note Transitions LSE Bypass to LSE On and LSE On to LSE Bypass are not
+ * supported by this API. User should request a transition to LSE Off
+ * first and then LSE On or LSE Bypass.
+ * @note Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not
+ * supported by this API. User should request a transition to HSE Off
+ * first and then HSE On or HSE Bypass.
+ * @retval HAL status
+ */
+__weak HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct)
+{
+ uint32_t tickstart;
+
+ /* Check Null pointer */
+ if(RCC_OscInitStruct == NULL)
+ {
+ return HAL_ERROR;
+ }
+
+ /* Check the parameters */
+ assert_param(IS_RCC_OSCILLATORTYPE(RCC_OscInitStruct->OscillatorType));
+ /*------------------------------- HSE Configuration ------------------------*/
+ if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE)
+ {
+ /* Check the parameters */
+ assert_param(IS_RCC_HSE(RCC_OscInitStruct->HSEState));
+ /* When the HSE is used as system clock or clock source for PLL in these cases HSE will not disabled */
+ if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_HSE) ||\
+ ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLL) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSE)))
+ {
+ if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET) && (RCC_OscInitStruct->HSEState == RCC_HSE_OFF))
+ {
+ return HAL_ERROR;
+ }
+ }
+ else
+ {
+ /* Set the new HSE configuration ---------------------------------------*/
+ __HAL_RCC_HSE_CONFIG(RCC_OscInitStruct->HSEState);
+
+ /* Check the HSE State */
+ if((RCC_OscInitStruct->HSEState) != RCC_HSE_OFF)
+ {
+ /* Get Start Tick */
+ tickstart = HAL_GetTick();
+
+ /* Wait till HSE is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ else
+ {
+ /* Get Start Tick */
+ tickstart = HAL_GetTick();
+
+ /* Wait till HSE is bypassed or disabled */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) != RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > HSE_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ }
+ }
+ /*----------------------------- HSI Configuration --------------------------*/
+ if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI)
+ {
+ /* Check the parameters */
+ assert_param(IS_RCC_HSI(RCC_OscInitStruct->HSIState));
+ assert_param(IS_RCC_CALIBRATION_VALUE(RCC_OscInitStruct->HSICalibrationValue));
+
+ /* Check if HSI is used as system clock or as PLL source when PLL is selected as system clock */
+ if((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_HSI) ||\
+ ((__HAL_RCC_GET_SYSCLK_SOURCE() == RCC_CFGR_SWS_PLL) && ((RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC) == RCC_PLLCFGR_PLLSRC_HSI)))
+ {
+ /* When HSI is used as system clock it will not disabled */
+ if((__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET) && (RCC_OscInitStruct->HSIState != RCC_HSI_ON))
+ {
+ return HAL_ERROR;
+ }
+ /* Otherwise, just the calibration is allowed */
+ else
+ {
+ /* Adjusts the Internal High Speed oscillator (HSI) calibration value.*/
+ __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue);
+ }
+ }
+ else
+ {
+ /* Check the HSI State */
+ if((RCC_OscInitStruct->HSIState)!= RCC_HSI_OFF)
+ {
+ /* Enable the Internal High Speed oscillator (HSI). */
+ __HAL_RCC_HSI_ENABLE();
+
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ /* Wait till HSI is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+
+ /* Adjusts the Internal High Speed oscillator (HSI) calibration value. */
+ __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(RCC_OscInitStruct->HSICalibrationValue);
+ }
+ else
+ {
+ /* Disable the Internal High Speed oscillator (HSI). */
+ __HAL_RCC_HSI_DISABLE();
+
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ /* Wait till HSI is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) != RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > HSI_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ }
+ }
+ /*------------------------------ LSI Configuration -------------------------*/
+ if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI)
+ {
+ /* Check the parameters */
+ assert_param(IS_RCC_LSI(RCC_OscInitStruct->LSIState));
+
+ /* Check the LSI State */
+ if((RCC_OscInitStruct->LSIState)!= RCC_LSI_OFF)
+ {
+ /* Enable the Internal Low Speed oscillator (LSI). */
+ __HAL_RCC_LSI_ENABLE();
+
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ /* Wait till LSI is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) == RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ else
+ {
+ /* Disable the Internal Low Speed oscillator (LSI). */
+ __HAL_RCC_LSI_DISABLE();
+
+ /* Get Start Tick */
+ tickstart = HAL_GetTick();
+
+ /* Wait till LSI is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSIRDY) != RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > LSI_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ }
+ /*------------------------------ LSE Configuration -------------------------*/
+ if(((RCC_OscInitStruct->OscillatorType) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE)
+ {
+ FlagStatus pwrclkchanged = RESET;
+
+ /* Check the parameters */
+ assert_param(IS_RCC_LSE(RCC_OscInitStruct->LSEState));
+
+ /* Update LSE configuration in Backup Domain control register */
+ /* Requires to enable write access to Backup Domain of necessary */
+ if(__HAL_RCC_PWR_IS_CLK_DISABLED())
+ {
+ __HAL_RCC_PWR_CLK_ENABLE();
+ pwrclkchanged = SET;
+ }
+
+ if(HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP))
+ {
+ /* Enable write access to Backup domain */
+ SET_BIT(PWR->CR, PWR_CR_DBP);
+
+ /* Wait for Backup domain Write protection disable */
+ tickstart = HAL_GetTick();
+
+ while(HAL_IS_BIT_CLR(PWR->CR, PWR_CR_DBP))
+ {
+ if((HAL_GetTick() - tickstart) > RCC_DBP_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+
+ /* Set the new LSE configuration -----------------------------------------*/
+ __HAL_RCC_LSE_CONFIG(RCC_OscInitStruct->LSEState);
+ /* Check the LSE State */
+ if((RCC_OscInitStruct->LSEState) != RCC_LSE_OFF)
+ {
+ /* Get Start Tick*/
+ tickstart = HAL_GetTick();
+
+ /* Wait till LSE is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) == RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ else
+ {
+ /* Get Start Tick */
+ tickstart = HAL_GetTick();
+
+ /* Wait till LSE is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_LSERDY) != RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > RCC_LSE_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+
+ /* Restore clock configuration if changed */
+ if(pwrclkchanged == SET)
+ {
+ __HAL_RCC_PWR_CLK_DISABLE();
+ }
+ }
+ /*-------------------------------- PLL Configuration -----------------------*/
+ /* Check the parameters */
+ assert_param(IS_RCC_PLL(RCC_OscInitStruct->PLL.PLLState));
+ if ((RCC_OscInitStruct->PLL.PLLState) != RCC_PLL_NONE)
+ {
+ /* Check if the PLL is used as system clock or not */
+ if(__HAL_RCC_GET_SYSCLK_SOURCE() != RCC_CFGR_SWS_PLL)
+ {
+ if((RCC_OscInitStruct->PLL.PLLState) == RCC_PLL_ON)
+ {
+ /* Check the parameters */
+ assert_param(IS_RCC_PLLSOURCE(RCC_OscInitStruct->PLL.PLLSource));
+ assert_param(IS_RCC_PLLM_VALUE(RCC_OscInitStruct->PLL.PLLM));
+ assert_param(IS_RCC_PLLN_VALUE(RCC_OscInitStruct->PLL.PLLN));
+ assert_param(IS_RCC_PLLP_VALUE(RCC_OscInitStruct->PLL.PLLP));
+ assert_param(IS_RCC_PLLQ_VALUE(RCC_OscInitStruct->PLL.PLLQ));
+
+ /* Disable the main PLL. */
+ __HAL_RCC_PLL_DISABLE();
+
+ /* Get Start Tick */
+ tickstart = HAL_GetTick();
+
+ /* Wait till PLL is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+
+ /* Configure the main PLL clock source, multiplication and division factors. */
+ WRITE_REG(RCC->PLLCFGR, (RCC_OscInitStruct->PLL.PLLSource | \
+ RCC_OscInitStruct->PLL.PLLM | \
+ (RCC_OscInitStruct->PLL.PLLN << RCC_PLLCFGR_PLLN_Pos) | \
+ (((RCC_OscInitStruct->PLL.PLLP >> 1U) - 1U) << RCC_PLLCFGR_PLLP_Pos) | \
+ (RCC_OscInitStruct->PLL.PLLQ << RCC_PLLCFGR_PLLQ_Pos)));
+ /* Enable the main PLL. */
+ __HAL_RCC_PLL_ENABLE();
+
+ /* Get Start Tick */
+ tickstart = HAL_GetTick();
+
+ /* Wait till PLL is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ else
+ {
+ /* Disable the main PLL. */
+ __HAL_RCC_PLL_DISABLE();
+
+ /* Get Start Tick */
+ tickstart = HAL_GetTick();
+
+ /* Wait till PLL is ready */
+ while(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) != RESET)
+ {
+ if((HAL_GetTick() - tickstart ) > PLL_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+ }
+ else
+ {
+ return HAL_ERROR;
+ }
+ }
+ return HAL_OK;
+}
+
+/**
+ * @brief Initializes the CPU, AHB and APB busses clocks according to the specified
+ * parameters in the RCC_ClkInitStruct.
+ * @param RCC_ClkInitStruct pointer to an RCC_OscInitTypeDef structure that
+ * contains the configuration information for the RCC peripheral.
+ * @param FLatency FLASH Latency, this parameter depend on device selected
+ *
+ * @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency
+ * and updated by HAL_RCC_GetHCLKFreq() function called within this function
+ *
+ * @note The HSI is used (enabled by hardware) as system clock source after
+ * startup from Reset, wake-up from STOP and STANDBY mode, or in case
+ * of failure of the HSE used directly or indirectly as system clock
+ * (if the Clock Security System CSS is enabled).
+ *
+ * @note A switch from one clock source to another occurs only if the target
+ * clock source is ready (clock stable after startup delay or PLL locked).
+ * If a clock source which is not yet ready is selected, the switch will
+ * occur when the clock source will be ready.
+ *
+ * @note Depending on the device voltage range, the software has to set correctly
+ * HPRE[3:0] bits to ensure that HCLK not exceed the maximum allowed frequency
+ * (for more details refer to section above "Initialization/de-initialization functions")
+ * @retval None
+ */
+HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t FLatency)
+{
+ uint32_t tickstart;
+
+ /* Check Null pointer */
+ if(RCC_ClkInitStruct == NULL)
+ {
+ return HAL_ERROR;
+ }
+
+ /* Check the parameters */
+ assert_param(IS_RCC_CLOCKTYPE(RCC_ClkInitStruct->ClockType));
+ assert_param(IS_FLASH_LATENCY(FLatency));
+
+ /* To correctly read data from FLASH memory, the number of wait states (LATENCY)
+ must be correctly programmed according to the frequency of the CPU clock
+ (HCLK) and the supply voltage of the device. */
+
+ /* Increasing the number of wait states because of higher CPU frequency */
+ if(FLatency > __HAL_FLASH_GET_LATENCY())
+ {
+ /* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */
+ __HAL_FLASH_SET_LATENCY(FLatency);
+
+ /* Check that the new number of wait states is taken into account to access the Flash
+ memory by reading the FLASH_ACR register */
+ if(__HAL_FLASH_GET_LATENCY() != FLatency)
+ {
+ return HAL_ERROR;
+ }
+ }
+
+ /*-------------------------- HCLK Configuration --------------------------*/
+ if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_HCLK) == RCC_CLOCKTYPE_HCLK)
+ {
+ /* Set the highest APBx dividers in order to ensure that we do not go through
+ a non-spec phase whatever we decrease or increase HCLK. */
+ if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK1) == RCC_CLOCKTYPE_PCLK1)
+ {
+ MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE1, RCC_HCLK_DIV16);
+ }
+
+ if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK2) == RCC_CLOCKTYPE_PCLK2)
+ {
+ MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE2, (RCC_HCLK_DIV16 << 3));
+ }
+
+ assert_param(IS_RCC_HCLK(RCC_ClkInitStruct->AHBCLKDivider));
+ MODIFY_REG(RCC->CFGR, RCC_CFGR_HPRE, RCC_ClkInitStruct->AHBCLKDivider);
+ }
+
+ /*------------------------- SYSCLK Configuration ---------------------------*/
+ if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_SYSCLK) == RCC_CLOCKTYPE_SYSCLK)
+ {
+ assert_param(IS_RCC_SYSCLKSOURCE(RCC_ClkInitStruct->SYSCLKSource));
+
+ /* HSE is selected as System Clock Source */
+ if(RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_HSE)
+ {
+ /* Check the HSE ready flag */
+ if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSERDY) == RESET)
+ {
+ return HAL_ERROR;
+ }
+ }
+ /* PLL is selected as System Clock Source */
+ else if((RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLCLK) ||
+ (RCC_ClkInitStruct->SYSCLKSource == RCC_SYSCLKSOURCE_PLLRCLK))
+ {
+ /* Check the PLL ready flag */
+ if(__HAL_RCC_GET_FLAG(RCC_FLAG_PLLRDY) == RESET)
+ {
+ return HAL_ERROR;
+ }
+ }
+ /* HSI is selected as System Clock Source */
+ else
+ {
+ /* Check the HSI ready flag */
+ if(__HAL_RCC_GET_FLAG(RCC_FLAG_HSIRDY) == RESET)
+ {
+ return HAL_ERROR;
+ }
+ }
+
+ __HAL_RCC_SYSCLK_CONFIG(RCC_ClkInitStruct->SYSCLKSource);
+
+ /* Get Start Tick */
+ tickstart = HAL_GetTick();
+
+ while (__HAL_RCC_GET_SYSCLK_SOURCE() != (RCC_ClkInitStruct->SYSCLKSource << RCC_CFGR_SWS_Pos))
+ {
+ if ((HAL_GetTick() - tickstart) > CLOCKSWITCH_TIMEOUT_VALUE)
+ {
+ return HAL_TIMEOUT;
+ }
+ }
+ }
+
+ /* Decreasing the number of wait states because of lower CPU frequency */
+ if(FLatency < __HAL_FLASH_GET_LATENCY())
+ {
+ /* Program the new number of wait states to the LATENCY bits in the FLASH_ACR register */
+ __HAL_FLASH_SET_LATENCY(FLatency);
+
+ /* Check that the new number of wait states is taken into account to access the Flash
+ memory by reading the FLASH_ACR register */
+ if(__HAL_FLASH_GET_LATENCY() != FLatency)
+ {
+ return HAL_ERROR;
+ }
+ }
+
+ /*-------------------------- PCLK1 Configuration ---------------------------*/
+ if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK1) == RCC_CLOCKTYPE_PCLK1)
+ {
+ assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB1CLKDivider));
+ MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE1, RCC_ClkInitStruct->APB1CLKDivider);
+ }
+
+ /*-------------------------- PCLK2 Configuration ---------------------------*/
+ if(((RCC_ClkInitStruct->ClockType) & RCC_CLOCKTYPE_PCLK2) == RCC_CLOCKTYPE_PCLK2)
+ {
+ assert_param(IS_RCC_PCLK(RCC_ClkInitStruct->APB2CLKDivider));
+ MODIFY_REG(RCC->CFGR, RCC_CFGR_PPRE2, ((RCC_ClkInitStruct->APB2CLKDivider) << 3U));
+ }
+
+ /* Update the SystemCoreClock global variable */
+ SystemCoreClock = HAL_RCC_GetSysClockFreq() >> AHBPrescTable[(RCC->CFGR & RCC_CFGR_HPRE)>> RCC_CFGR_HPRE_Pos];
+
+ /* Configure the source of time base considering new system clocks settings */
+ HAL_InitTick (TICK_INT_PRIORITY);
+
+ return HAL_OK;
+}
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_Exported_Functions_Group2 Peripheral Control functions
+ * @brief RCC clocks control functions
+ *
+@verbatim
+ ===============================================================================
+ ##### Peripheral Control functions #####
+ ===============================================================================
+ [..]
+ This subsection provides a set of functions allowing to control the RCC Clocks
+ frequencies.
+
+@endverbatim
+ * @{
+ */
+
+/**
+ * @brief Selects the clock source to output on MCO1 pin(PA8) or on MCO2 pin(PC9).
+ * @note PA8/PC9 should be configured in alternate function mode.
+ * @param RCC_MCOx specifies the output direction for the clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_MCO1: Clock source to output on MCO1 pin(PA8).
+ * @arg RCC_MCO2: Clock source to output on MCO2 pin(PC9).
+ * @param RCC_MCOSource specifies the clock source to output.
+ * This parameter can be one of the following values:
+ * @arg RCC_MCO1SOURCE_HSI: HSI clock selected as MCO1 source
+ * @arg RCC_MCO1SOURCE_LSE: LSE clock selected as MCO1 source
+ * @arg RCC_MCO1SOURCE_HSE: HSE clock selected as MCO1 source
+ * @arg RCC_MCO1SOURCE_PLLCLK: main PLL clock selected as MCO1 source
+ * @arg RCC_MCO2SOURCE_SYSCLK: System clock (SYSCLK) selected as MCO2 source
+ * @arg RCC_MCO2SOURCE_PLLI2SCLK: PLLI2S clock selected as MCO2 source, available for all STM32F4 devices except STM32F410xx
+ * @arg RCC_MCO2SOURCE_I2SCLK: I2SCLK clock selected as MCO2 source, available only for STM32F410Rx devices
+ * @arg RCC_MCO2SOURCE_HSE: HSE clock selected as MCO2 source
+ * @arg RCC_MCO2SOURCE_PLLCLK: main PLL clock selected as MCO2 source
+ * @param RCC_MCODiv specifies the MCOx prescaler.
+ * This parameter can be one of the following values:
+ * @arg RCC_MCODIV_1: no division applied to MCOx clock
+ * @arg RCC_MCODIV_2: division by 2 applied to MCOx clock
+ * @arg RCC_MCODIV_3: division by 3 applied to MCOx clock
+ * @arg RCC_MCODIV_4: division by 4 applied to MCOx clock
+ * @arg RCC_MCODIV_5: division by 5 applied to MCOx clock
+ * @note For STM32F410Rx devices to output I2SCLK clock on MCO2 you should have
+ * at last one of the SPI clocks enabled (SPI1, SPI2 or SPI5).
+ * @retval None
+ */
+void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv)
+{
+ GPIO_InitTypeDef GPIO_InitStruct;
+ /* Check the parameters */
+ assert_param(IS_RCC_MCO(RCC_MCOx));
+ assert_param(IS_RCC_MCODIV(RCC_MCODiv));
+ /* RCC_MCO1 */
+ if(RCC_MCOx == RCC_MCO1)
+ {
+ assert_param(IS_RCC_MCO1SOURCE(RCC_MCOSource));
+
+ /* MCO1 Clock Enable */
+ __MCO1_CLK_ENABLE();
+
+ /* Configure the MCO1 pin in alternate function mode */
+ GPIO_InitStruct.Pin = MCO1_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Alternate = GPIO_AF0_MCO;
+ HAL_GPIO_Init(MCO1_GPIO_PORT, &GPIO_InitStruct);
+
+ /* Mask MCO1 and MCO1PRE[2:0] bits then Select MCO1 clock source and prescaler */
+ MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO1 | RCC_CFGR_MCO1PRE), (RCC_MCOSource | RCC_MCODiv));
+
+ /* This RCC MCO1 enable feature is available only on STM32F410xx devices */
+#if defined(RCC_CFGR_MCO1EN)
+ __HAL_RCC_MCO1_ENABLE();
+#endif /* RCC_CFGR_MCO1EN */
+ }
+#if defined(RCC_CFGR_MCO2)
+ else
+ {
+ assert_param(IS_RCC_MCO2SOURCE(RCC_MCOSource));
+
+ /* MCO2 Clock Enable */
+ __MCO2_CLK_ENABLE();
+
+ /* Configure the MCO2 pin in alternate function mode */
+ GPIO_InitStruct.Pin = MCO2_PIN;
+ GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+ GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+ GPIO_InitStruct.Pull = GPIO_NOPULL;
+ GPIO_InitStruct.Alternate = GPIO_AF0_MCO;
+ HAL_GPIO_Init(MCO2_GPIO_PORT, &GPIO_InitStruct);
+
+ /* Mask MCO2 and MCO2PRE[2:0] bits then Select MCO2 clock source and prescaler */
+ MODIFY_REG(RCC->CFGR, (RCC_CFGR_MCO2 | RCC_CFGR_MCO2PRE), (RCC_MCOSource | (RCC_MCODiv << 3U)));
+
+ /* This RCC MCO2 enable feature is available only on STM32F410Rx devices */
+#if defined(RCC_CFGR_MCO2EN)
+ __HAL_RCC_MCO2_ENABLE();
+#endif /* RCC_CFGR_MCO2EN */
+ }
+#endif /* RCC_CFGR_MCO2 */
+}
+
+/**
+ * @brief Enables the Clock Security System.
+ * @note If a failure is detected on the HSE oscillator clock, this oscillator
+ * is automatically disabled and an interrupt is generated to inform the
+ * software about the failure (Clock Security System Interrupt, CSSI),
+ * allowing the MCU to perform rescue operations. The CSSI is linked to
+ * the Cortex-M4 NMI (Non-Maskable Interrupt) exception vector.
+ * @retval None
+ */
+void HAL_RCC_EnableCSS(void)
+{
+ *(__IO uint32_t *) RCC_CR_CSSON_BB = (uint32_t)ENABLE;
+}
+
+/**
+ * @brief Disables the Clock Security System.
+ * @retval None
+ */
+void HAL_RCC_DisableCSS(void)
+{
+ *(__IO uint32_t *) RCC_CR_CSSON_BB = (uint32_t)DISABLE;
+}
+
+/**
+ * @brief Returns the SYSCLK frequency
+ *
+ * @note The system frequency computed by this function is not the real
+ * frequency in the chip. It is calculated based on the predefined
+ * constant and the selected clock source:
+ * @note If SYSCLK source is HSI, function returns values based on HSI_VALUE(*)
+ * @note If SYSCLK source is HSE, function returns values based on HSE_VALUE(**)
+ * @note If SYSCLK source is PLL, function returns values based on HSE_VALUE(**)
+ * or HSI_VALUE(*) multiplied/divided by the PLL factors.
+ * @note (*) HSI_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
+ * 16 MHz) but the real value may vary depending on the variations
+ * in voltage and temperature.
+ * @note (**) HSE_VALUE is a constant defined in stm32f4xx_hal_conf.h file (default value
+ * 25 MHz), user has to ensure that HSE_VALUE is same as the real
+ * frequency of the crystal used. Otherwise, this function may
+ * have wrong result.
+ *
+ * @note The result of this function could be not correct when using fractional
+ * value for HSE crystal.
+ *
+ * @note This function can be used by the user application to compute the
+ * baudrate for the communication peripherals or configure other parameters.
+ *
+ * @note Each time SYSCLK changes, this function must be called to update the
+ * right SYSCLK value. Otherwise, any configuration based on this function will be incorrect.
+ *
+ *
+ * @retval SYSCLK frequency
+ */
+__weak uint32_t HAL_RCC_GetSysClockFreq(void)
+{
+ uint32_t pllm = 0U, pllvco = 0U, pllp = 0U;
+ uint32_t sysclockfreq = 0U;
+
+ /* Get SYSCLK source -------------------------------------------------------*/
+ switch (RCC->CFGR & RCC_CFGR_SWS)
+ {
+ case RCC_CFGR_SWS_HSI: /* HSI used as system clock source */
+ {
+ sysclockfreq = HSI_VALUE;
+ break;
+ }
+ case RCC_CFGR_SWS_HSE: /* HSE used as system clock source */
+ {
+ sysclockfreq = HSE_VALUE;
+ break;
+ }
+ case RCC_CFGR_SWS_PLL: /* PLL used as system clock source */
+ {
+ /* PLL_VCO = (HSE_VALUE or HSI_VALUE / PLLM) * PLLN
+ SYSCLK = PLL_VCO / PLLP */
+ pllm = RCC->PLLCFGR & RCC_PLLCFGR_PLLM;
+ if(__HAL_RCC_GET_PLL_OSCSOURCE() != RCC_PLLSOURCE_HSI)
+ {
+ /* HSE used as PLL clock source */
+ pllvco = (uint32_t) ((((uint64_t) HSE_VALUE * ((uint64_t) ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> RCC_PLLCFGR_PLLN_Pos)))) / (uint64_t)pllm);
+ }
+ else
+ {
+ /* HSI used as PLL clock source */
+ pllvco = (uint32_t) ((((uint64_t) HSI_VALUE * ((uint64_t) ((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> RCC_PLLCFGR_PLLN_Pos)))) / (uint64_t)pllm);
+ }
+ pllp = ((((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) >> RCC_PLLCFGR_PLLP_Pos) + 1U) *2U);
+
+ sysclockfreq = pllvco/pllp;
+ break;
+ }
+ default:
+ {
+ sysclockfreq = HSI_VALUE;
+ break;
+ }
+ }
+ return sysclockfreq;
+}
+
+/**
+ * @brief Returns the HCLK frequency
+ * @note Each time HCLK changes, this function must be called to update the
+ * right HCLK value. Otherwise, any configuration based on this function will be incorrect.
+ *
+ * @note The SystemCoreClock CMSIS variable is used to store System Clock Frequency
+ * and updated within this function
+ * @retval HCLK frequency
+ */
+uint32_t HAL_RCC_GetHCLKFreq(void)
+{
+ return SystemCoreClock;
+}
+
+/**
+ * @brief Returns the PCLK1 frequency
+ * @note Each time PCLK1 changes, this function must be called to update the
+ * right PCLK1 value. Otherwise, any configuration based on this function will be incorrect.
+ * @retval PCLK1 frequency
+ */
+uint32_t HAL_RCC_GetPCLK1Freq(void)
+{
+ /* Get HCLK source and Compute PCLK1 frequency ---------------------------*/
+ return (HAL_RCC_GetHCLKFreq() >> APBPrescTable[(RCC->CFGR & RCC_CFGR_PPRE1)>> RCC_CFGR_PPRE1_Pos]);
+}
+
+/**
+ * @brief Returns the PCLK2 frequency
+ * @note Each time PCLK2 changes, this function must be called to update the
+ * right PCLK2 value. Otherwise, any configuration based on this function will be incorrect.
+ * @retval PCLK2 frequency
+ */
+uint32_t HAL_RCC_GetPCLK2Freq(void)
+{
+ /* Get HCLK source and Compute PCLK2 frequency ---------------------------*/
+ return (HAL_RCC_GetHCLKFreq()>> APBPrescTable[(RCC->CFGR & RCC_CFGR_PPRE2)>> RCC_CFGR_PPRE2_Pos]);
+}
+
+/**
+ * @brief Configures the RCC_OscInitStruct according to the internal
+ * RCC configuration registers.
+ * @param RCC_OscInitStruct pointer to an RCC_OscInitTypeDef structure that
+ * will be configured.
+ * @retval None
+ */
+__weak void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct)
+{
+ /* Set all possible values for the Oscillator type parameter ---------------*/
+ RCC_OscInitStruct->OscillatorType = RCC_OSCILLATORTYPE_HSE | RCC_OSCILLATORTYPE_HSI | RCC_OSCILLATORTYPE_LSE | RCC_OSCILLATORTYPE_LSI;
+
+ /* Get the HSE configuration -----------------------------------------------*/
+ if((RCC->CR &RCC_CR_HSEBYP) == RCC_CR_HSEBYP)
+ {
+ RCC_OscInitStruct->HSEState = RCC_HSE_BYPASS;
+ }
+ else if((RCC->CR &RCC_CR_HSEON) == RCC_CR_HSEON)
+ {
+ RCC_OscInitStruct->HSEState = RCC_HSE_ON;
+ }
+ else
+ {
+ RCC_OscInitStruct->HSEState = RCC_HSE_OFF;
+ }
+
+ /* Get the HSI configuration -----------------------------------------------*/
+ if((RCC->CR &RCC_CR_HSION) == RCC_CR_HSION)
+ {
+ RCC_OscInitStruct->HSIState = RCC_HSI_ON;
+ }
+ else
+ {
+ RCC_OscInitStruct->HSIState = RCC_HSI_OFF;
+ }
+
+ RCC_OscInitStruct->HSICalibrationValue = (uint32_t)((RCC->CR &RCC_CR_HSITRIM) >> RCC_CR_HSITRIM_Pos);
+
+ /* Get the LSE configuration -----------------------------------------------*/
+ if((RCC->BDCR &RCC_BDCR_LSEBYP) == RCC_BDCR_LSEBYP)
+ {
+ RCC_OscInitStruct->LSEState = RCC_LSE_BYPASS;
+ }
+ else if((RCC->BDCR &RCC_BDCR_LSEON) == RCC_BDCR_LSEON)
+ {
+ RCC_OscInitStruct->LSEState = RCC_LSE_ON;
+ }
+ else
+ {
+ RCC_OscInitStruct->LSEState = RCC_LSE_OFF;
+ }
+
+ /* Get the LSI configuration -----------------------------------------------*/
+ if((RCC->CSR &RCC_CSR_LSION) == RCC_CSR_LSION)
+ {
+ RCC_OscInitStruct->LSIState = RCC_LSI_ON;
+ }
+ else
+ {
+ RCC_OscInitStruct->LSIState = RCC_LSI_OFF;
+ }
+
+ /* Get the PLL configuration -----------------------------------------------*/
+ if((RCC->CR &RCC_CR_PLLON) == RCC_CR_PLLON)
+ {
+ RCC_OscInitStruct->PLL.PLLState = RCC_PLL_ON;
+ }
+ else
+ {
+ RCC_OscInitStruct->PLL.PLLState = RCC_PLL_OFF;
+ }
+ RCC_OscInitStruct->PLL.PLLSource = (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC);
+ RCC_OscInitStruct->PLL.PLLM = (uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLM);
+ RCC_OscInitStruct->PLL.PLLN = (uint32_t)((RCC->PLLCFGR & RCC_PLLCFGR_PLLN) >> RCC_PLLCFGR_PLLN_Pos);
+ RCC_OscInitStruct->PLL.PLLP = (uint32_t)((((RCC->PLLCFGR & RCC_PLLCFGR_PLLP) + RCC_PLLCFGR_PLLP_0) << 1U) >> RCC_PLLCFGR_PLLP_Pos);
+ RCC_OscInitStruct->PLL.PLLQ = (uint32_t)((RCC->PLLCFGR & RCC_PLLCFGR_PLLQ) >> RCC_PLLCFGR_PLLQ_Pos);
+}
+
+/**
+ * @brief Configures the RCC_ClkInitStruct according to the internal
+ * RCC configuration registers.
+ * @param RCC_ClkInitStruct pointer to an RCC_ClkInitTypeDef structure that
+ * will be configured.
+ * @param pFLatency Pointer on the Flash Latency.
+ * @retval None
+ */
+void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t *pFLatency)
+{
+ /* Set all possible values for the Clock type parameter --------------------*/
+ RCC_ClkInitStruct->ClockType = RCC_CLOCKTYPE_SYSCLK | RCC_CLOCKTYPE_HCLK | RCC_CLOCKTYPE_PCLK1 | RCC_CLOCKTYPE_PCLK2;
+
+ /* Get the SYSCLK configuration --------------------------------------------*/
+ RCC_ClkInitStruct->SYSCLKSource = (uint32_t)(RCC->CFGR & RCC_CFGR_SW);
+
+ /* Get the HCLK configuration ----------------------------------------------*/
+ RCC_ClkInitStruct->AHBCLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_HPRE);
+
+ /* Get the APB1 configuration ----------------------------------------------*/
+ RCC_ClkInitStruct->APB1CLKDivider = (uint32_t)(RCC->CFGR & RCC_CFGR_PPRE1);
+
+ /* Get the APB2 configuration ----------------------------------------------*/
+ RCC_ClkInitStruct->APB2CLKDivider = (uint32_t)((RCC->CFGR & RCC_CFGR_PPRE2) >> 3U);
+
+ /* Get the Flash Wait State (Latency) configuration ------------------------*/
+ *pFLatency = (uint32_t)(FLASH->ACR & FLASH_ACR_LATENCY);
+}
+
+/**
+ * @brief This function handles the RCC CSS interrupt request.
+ * @note This API should be called under the NMI_Handler().
+ * @retval None
+ */
+void HAL_RCC_NMI_IRQHandler(void)
+{
+ /* Check RCC CSSF flag */
+ if(__HAL_RCC_GET_IT(RCC_IT_CSS))
+ {
+ /* RCC Clock Security System interrupt user callback */
+ HAL_RCC_CSSCallback();
+
+ /* Clear RCC CSS pending bit */
+ __HAL_RCC_CLEAR_IT(RCC_IT_CSS);
+ }
+}
+
+/**
+ * @brief RCC Clock Security System interrupt callback
+ * @retval None
+ */
+__weak void HAL_RCC_CSSCallback(void)
+{
+ /* NOTE : This function Should not be modified, when the callback is needed,
+ the HAL_RCC_CSSCallback could be implemented in the user file
+ */
+}
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+#endif /* HAL_RCC_MODULE_ENABLED */
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/