Thomas Lyp
Initial commit
Diff: mbed-dev-master/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F437xG/TARGET_UBLOX_C030/PinNames.h
- Revision:
- 0:bb348c97df44
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed-dev-master/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F437xG/TARGET_UBLOX_C030/PinNames.h Wed Sep 16 01:11:49 2020 +0000
@@ -0,0 +1,195 @@
+/* mbed Microcontroller Library
+ *******************************************************************************
+ * Copyright (c) 2014, STMicroelectronics
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *******************************************************************************
+ */
+#ifndef MBED_PINNAMES_H
+#define MBED_PINNAMES_H
+
+#include "cmsis.h"
+#include "PinNamesTypes.h"
+
+#ifdef __cplusplus
+extern "C" {
+#endif
+
+typedef enum {
+ PA_0 = 0x00, PA_1 = 0x01, PA_2 = 0x02, PA_3 = 0x03,
+ PA_4 = 0x04, PA_5 = 0x05, PA_6 = 0x06, PA_7 = 0x07,
+ PA_8 = 0x08, PA_9 = 0x09, PA_10 = 0x0A, PA_11 = 0x0B,
+ PA_12 = 0x0C, PA_13 = 0x0D, PA_14 = 0x0E, PA_15 = 0x0F,
+
+ PB_0 = 0x10, PB_1 = 0x11, PB_2 = 0x12, PB_3 = 0x13,
+ PB_4 = 0x14, PB_5 = 0x15, PB_6 = 0x16, PB_7 = 0x17,
+ PB_8 = 0x18, PB_9 = 0x19, PB_10 = 0x1A, PB_11 = 0x1B,
+ PB_12 = 0x1C, PB_13 = 0x1D, PB_14 = 0x1E, PB_15 = 0x1F,
+
+ PC_0 = 0x20, PC_1 = 0x21, PC_2 = 0x22, PC_3 = 0x23,
+ PC_4 = 0x24, PC_5 = 0x25, PC_6 = 0x26, PC_7 = 0x27,
+ PC_8 = 0x28, PC_9 = 0x29, PC_10 = 0x2A, PC_11 = 0x2B,
+ PC_12 = 0x2C, PC_13 = 0x2D, PC_14 = 0x2E, PC_15 = 0x2F,
+
+ PD_0 = 0x30, PD_1 = 0x31, PD_2 = 0x32, PD_3 = 0x33,
+ PD_4 = 0x34, PD_5 = 0x35, PD_6 = 0x36, PD_7 = 0x37,
+ PD_8 = 0x38, PD_9 = 0x39, PD_10 = 0x3A, PD_11 = 0x3B,
+ PD_12 = 0x3C, PD_13 = 0x3D, PD_14 = 0x3E, PD_15 = 0x3F,
+
+ PE_0 = 0x40, PE_1 = 0x41, PE_2 = 0x42, PE_3 = 0x43,
+ PE_4 = 0x44, PE_5 = 0x45, PE_6 = 0x46, PE_7 = 0x47,
+ PE_8 = 0x48, PE_9 = 0x49, PE_10 = 0x4A, PE_11 = 0x4B,
+ PE_12 = 0x4C, PE_13 = 0x4D, PE_14 = 0x4E, PE_15 = 0x4F,
+
+
+ PH_0 = 0x70, PH_1 = 0x71,
+
+ // Not connected
+ NC = -1,
+
+ // Power
+ PWR3V3 = PE_0, // 3.3V rail for the Arduino interface,
+ // user LEDs and GNSS power, should be
+ // set to open drain output
+
+ // GNSS
+ GNSSEN = PA_15, // VCC_IO to GNSS, should be set to push-pull, no pull-up, output
+ GNSSTXD = PC_6,
+ GNSSRXD = PC_7,
+
+ // Cellular modem (a DCE)
+ MDMPWRON = PE_14, // Power (active high)
+ MDMRST = PB_5, // Reset (active low)
+#if defined(TARGET_UBLOX_C030_R410M)
+ MDMTXD = PA_9, // Transmit Data
+ MDMRXD = PA_10, // Receive Data
+ MDMCTS = PA_11, // Clear to Send
+ MDMRTS = PA_12, // Request to Send
+#else
+ MDMTXD = PD_5, // Transmit Data
+ MDMRXD = PD_6, // Receive Data
+ MDMCTS = PD_3, // Clear to Send
+ MDMRTS = PD_4, // Request to Send
+#endif
+ MDMDCD = NC, // DCD line not connected
+ MDMDSR = NC, // DSR line not connected
+ MDMDTR = NC, // DTR line not connected
+ MDMRI = NC, // RI line not connected
+ MDMGPIO2 = PD_1, //
+ MDMGPIO3 = PB_4, //
+ MDMCURRENTSENSE = PC_2,
+
+ // SD card
+ SDPWRON = PE_10, // Set to high to power on the SD card
+ SDCSEL = PD_7, // SPI chip select for on-board SD card
+
+ // Board Pins
+ // A0-A5
+ A0 = PA_3,
+ A1 = PC_0,
+ A2 = PC_3,
+ A3 = PA_4,
+ A4 = PA_6,
+ A5 = PB_0,
+ // D0-D15
+ D0 = PD_9, // UART3-RX
+ D1 = PD_8, // UART3-TX
+ D2 = PD_11, // UART3-CTS
+ D3 = PB_14, // UART3-RTS
+ D4 = PB_1,
+ D5 = PA_5,
+ D6 = PB_8, // UART3-CTS
+ D7 = PB_15, // UART3-RTS
+ D8 = PD_15, // UART1-TX
+ D9 = PD_12, // SDCard-CS
+ D10 = PE_11, // SSEL
+ D11 = PE_6, // MOSI
+ D12 = PE_5, // MISO
+ D13 = PE_2, // SCK
+ D14 = PB_7, // SDA
+ D15 = PB_6, // SCL
+ // Internal
+ LED1 = PE_3, // Red / Mode
+ LED2 = PE_4, // Green / Switch-1
+ LED3 = PE_1, // Blue
+ LED4 = PE_7, // A definition is required by the mbed platform RTC test code, this is the Ethernet connector yellow LED
+ LED_RED = LED1,
+ SW0 = PC_13, // Switch-0
+
+ // Arduino header I2C
+ I2C_SDA = D14,
+ I2C_SCL = D15,
+
+ // On-board I2C
+ I2C_SDA_B = PC_9,
+ I2C_SCL_B = PA_8,
+
+ // SPI
+ SPI_MOSI = D11,
+ SPI_MISO = D12,
+ SPI_CLK = D13,
+ SPI_NSS = D10,
+
+ // STDIO for console print
+#ifdef MBED_CONF_TARGET_STDIO_UART_TX
+ STDIO_UART_TX = MBED_CONF_TARGET_STDIO_UART_TX,
+#else
+#if defined(TARGET_UBLOX_C030_R410M)
+ STDIO_UART_TX = PD_5,
+#else
+ STDIO_UART_TX = PA_9,
+#endif
+#endif
+#ifdef MBED_CONF_TARGET_STDIO_UART_RX
+ STDIO_UART_RX = MBED_CONF_TARGET_STDIO_UART_RX,
+#else
+#if defined(TARGET_UBLOX_C030_R410M)
+ STDIO_UART_RX = PD_6,
+#else
+ STDIO_UART_RX = PA_10,
+#endif
+#endif
+
+ // ST-Link
+ USBRX = STDIO_UART_RX,
+ USBTX = STDIO_UART_TX,
+ SWDIO = PA_13,
+ SWCLK = PA_14,
+ NTRST = PB_4,
+} PinName;
+
+#define ACTIVE_HIGH_POLARITY 1
+#define ACTIVE_LOW_POLARITY 0
+
+#define MDM_PIN_POLARITY ACTIVE_LOW_POLARITY
+
+// The default GNSS baud rate is set in targets.json
+// The default modem baud rate is set in the mbed_lib.json file under features/cellular/TARGET_UBLOX_MODEM_GENERIC/ubox_modem_driver
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif