QSPI.h

00001 /* mbed Microcontroller Library
00002  * Copyright (c) 2006-2018 ARM Limited
00003  *
00004  * Licensed under the Apache License, Version 2.0 (the "License");
00005  * you may not use this file except in compliance with the License.
00006  * You may obtain a copy of the License at
00007  *
00008  *     http://www.apache.org/licenses/LICENSE-2.0
00009  *
00010  * Unless required by applicable law or agreed to in writing, software
00011  * distributed under the License is distributed on an "AS IS" BASIS,
00012  * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
00013  * See the License for the specific language governing permissions and
00014  * limitations under the License.
00015  */
00016 #ifndef MBED_QSPI_H
00017 #define MBED_QSPI_H
00018 
00019 #include "platform/platform.h"
00020 
00021 #if defined (DEVICE_QSPI) || defined(DOXYGEN_ONLY)
00022 
00023 #include "hal/qspi_api.h"
00024 #include "platform/PlatformMutex.h"
00025 #include "platform/SingletonPtr.h"
00026 #include "platform/NonCopyable.h"
00027 
00028 #define ONE_MHZ     1000000
00029 
00030 namespace mbed {
00031 
00032 /** \addtogroup drivers */
00033 
00034 /** A QSPI Driver, used for communicating with QSPI slave devices
00035  *
00036  * The default format is set to Quad-SPI(1-1-1), and a clock frequency of 1MHz
00037  * Most QSPI devices will also require Chip Select which is indicated by ssel.
00038  *
00039  * @note Synchronization level: Thread safe
00040  *
00041  * Example:
00042  * @code
00043  * // Write 4 byte array to a QSPI slave, and read the response, note that each device will have its specific read/write/alt values defined
00044  *
00045  * #include "mbed.h"
00046  *
00047  * #define CMD_WRITE 0x02
00048  * #define CMD_READ  0x03
00049  * #define ADDRESS   0x1000
00050  *
00051  * // hardware ssel (where applicable)
00052  * QSPI qspi_device(QSPI_FLASH1_IO0, QSPI_FLASH1_IO1, QSPI_FLASH1_IO2, QSPI_FLASH1_IO3, QSPI_FLASH1_SCK, QSPI_FLASH1_CSN); // io0, io1, io2, io3, sclk, ssel
00053  *
00054  *
00055  * int main() {
00056  *     char tx_buf[] = { 0x11, 0x22, 0x33, 0x44 };
00057  *     char rx_buf[4];
00058  *     int buf_len = sizeof(tx_buf);
00059  *
00060  *     qspi_status_t result = qspi_device.write(CMD_WRITE, 0, ADDRESS, tx_buf, &buf_len);
00061  *     if (result != QSPI_STATUS_OK) {
00062  *        printf("Write failed");
00063  *     }
00064  *     result = qspi_device.read(CMD_READ, 0, ADDRESS, rx_buf, &buf_len);
00065  *     if (result != QSPI_STATUS_OK) {
00066  *        printf("Read failed");
00067  *     }
00068  *
00069  * }
00070  * @endcode
00071  * @ingroup drivers
00072  */
00073 class QSPI : private NonCopyable<QSPI> {
00074 
00075 public:
00076 
00077     /** Create a QSPI master connected to the specified pins
00078      *
00079      *  io0-io3 is used to specify the Pins used for Quad SPI mode
00080      *
00081      *  @param io0 1st IO pin used for sending/receiving data during data phase of a transaction
00082      *  @param io1 2nd IO pin used for sending/receiving data during data phase of a transaction
00083      *  @param io2 3rd IO pin used for sending/receiving data during data phase of a transaction
00084      *  @param io3 4th IO pin used for sending/receiving data during data phase of a transaction
00085      *  @param sclk QSPI Clock pin
00086      *  @param ssel QSPI chip select pin
00087      *  @param mode Clock polarity and phase mode (0 - 3) of SPI
00088      *         (Default: Mode=0 uses CPOL=0, CPHA=0, Mode=1 uses CPOL=1, CPHA=1)
00089      *
00090      */
00091     QSPI(PinName io0, PinName io1, PinName io2, PinName io3, PinName sclk, PinName ssel = NC, int mode = 0);
00092     virtual ~QSPI()
00093     {
00094     }
00095 
00096     /** Configure the data transmission format
00097      *
00098      *  @param inst_width Bus width used by instruction phase(Valid values are QSPI_CFG_BUS_SINGLE, QSPI_CFG_BUS_DUAL, QSPI_CFG_BUS_QUAD)
00099      *  @param address_width Bus width used by address phase(Valid values are QSPI_CFG_BUS_SINGLE, QSPI_CFG_BUS_DUAL, QSPI_CFG_BUS_QUAD)
00100      *  @param address_size Size in bits used by address phase(Valid values are QSPI_CFG_ADDR_SIZE_8, QSPI_CFG_ADDR_SIZE_16, QSPI_CFG_ADDR_SIZE_24, QSPI_CFG_ADDR_SIZE_32)
00101      *  @param alt_width Bus width used by alt phase(Valid values are QSPI_CFG_BUS_SINGLE, QSPI_CFG_BUS_DUAL, QSPI_CFG_BUS_QUAD)
00102      *  @param alt_size Size in bits used by alt phase(Valid values are QSPI_CFG_ALT_SIZE_8, QSPI_CFG_ALT_SIZE_16, QSPI_CFG_ALT_SIZE_24, QSPI_CFG_ALT_SIZE_32)
00103      *  @param data_width Bus width used by data phase(Valid values are QSPI_CFG_BUS_SINGLE, QSPI_CFG_BUS_DUAL, QSPI_CFG_BUS_QUAD)
00104      *  @param dummy_cycles Number of dummy clock cycles to be used after alt phase
00105      *
00106      */
00107     qspi_status_t configure_format(qspi_bus_width_t inst_width,
00108                                    qspi_bus_width_t address_width,
00109                                    qspi_address_size_t address_size,
00110                                    qspi_bus_width_t alt_width,
00111                                    qspi_alt_size_t alt_size,
00112                                    qspi_bus_width_t data_width,
00113                                    int dummy_cycles);
00114 
00115     /** Set the qspi bus clock frequency
00116      *
00117      *  @param hz SCLK frequency in hz (default = 1MHz)
00118      *  @returns
00119      *    Returns QSPI_STATUS_SUCCESS on successful, fails if the interface is already init-ed
00120      */
00121     qspi_status_t set_frequency(int hz = ONE_MHZ);
00122 
00123     /** Read from QSPI peripheral with the preset read_instruction and alt_value
00124      *
00125      *  @param address Address to be accessed in QSPI peripheral
00126      *  @param rx_buffer Buffer for data to be read from the peripheral
00127      *  @param rx_length Pointer to a variable containing the length of rx_buffer, and on return this variable will be updated with the actual number of bytes read
00128      *
00129      *  @returns
00130      *    Returns QSPI_STATUS_SUCCESS on successful reads and QSPI_STATUS_ERROR on failed reads.
00131      */
00132     qspi_status_t read(int address, char *rx_buffer, size_t *rx_length);
00133 
00134     /** Write to QSPI peripheral using custom write instruction
00135      *
00136      *  @param address Address to be accessed in QSPI peripheral
00137      *  @param tx_buffer Buffer containing data to be sent to peripheral
00138      *  @param tx_length Pointer to a variable containing the length of data to be transmitted, and on return this variable will be updated with the actual number of bytes written
00139      *
00140      *  @returns
00141      *    Returns QSPI_STATUS_SUCCESS on successful reads and QSPI_STATUS_ERROR on failed reads.
00142      */
00143     qspi_status_t write(int address, const char *tx_buffer, size_t *tx_length);
00144 
00145     /** Read from QSPI peripheral using custom read instruction, alt values
00146      *
00147      *  @param instruction Instruction value to be used in instruction phase
00148      *  @param alt Alt value to be used in Alternate-byte phase. Use -1 for ignoring Alternate-byte phase
00149      *  @param address Address to be accessed in QSPI peripheral
00150      *  @param rx_buffer Buffer for data to be read from the peripheral
00151      *  @param rx_length Pointer to a variable containing the length of rx_buffer, and on return this variable will be updated with the actual number of bytes read
00152      *
00153      *  @returns
00154      *    Returns QSPI_STATUS_SUCCESS on successful reads and QSPI_STATUS_ERROR on failed reads.
00155      */
00156     qspi_status_t read(int instruction, int alt, int address, char *rx_buffer, size_t *rx_length);
00157 
00158     /** Write to QSPI peripheral using custom write instruction, alt values
00159      *
00160      *  @param instruction Instruction value to be used in instruction phase
00161      *  @param alt Alt value to be used in Alternate-byte phase. Use -1 for ignoring Alternate-byte phase
00162      *  @param address Address to be accessed in QSPI peripheral
00163      *  @param tx_buffer Buffer containing data to be sent to peripheral
00164      *  @param tx_length Pointer to a variable containing the length of data to be transmitted, and on return this variable will be updated with the actual number of bytes written
00165      *
00166      *  @returns
00167      *    Returns QSPI_STATUS_SUCCESS on successful reads and QSPI_STATUS_ERROR on failed reads.
00168      */
00169     qspi_status_t write(int instruction, int alt, int address, const char *tx_buffer, size_t *tx_length);
00170 
00171     /** Perform a transaction to write to an address(a control register) and get the status results
00172      *
00173      *  @param instruction Instruction value to be used in instruction phase
00174      *  @param address Some instruction might require address. Use -1 if no address
00175      *  @param tx_buffer Buffer containing data to be sent to peripheral
00176      *  @param tx_length Pointer to a variable containing the length of data to be transmitted, and on return this variable will be updated with the actual number of bytes written
00177      *  @param rx_buffer Buffer for data to be read from the peripheral
00178      *  @param rx_length Pointer to a variable containing the length of rx_buffer, and on return this variable will be updated with the actual number of bytes read
00179      *
00180      *  @returns
00181      *    Returns QSPI_STATUS_SUCCESS on successful reads and QSPI_STATUS_ERROR on failed reads.
00182      */
00183     qspi_status_t command_transfer(int instruction, int address, const char *tx_buffer, size_t tx_length, const char *rx_buffer, size_t rx_length);
00184 
00185 #if !defined(DOXYGEN_ONLY)
00186 protected:
00187     /** Acquire exclusive access to this SPI bus
00188      */
00189     virtual void lock(void);
00190 
00191     /** Release exclusive access to this SPI bus
00192      */
00193     virtual void unlock(void);
00194 
00195     qspi_t _qspi;
00196 
00197     bool acquire(void);
00198     static QSPI *_owner;
00199     static SingletonPtr<PlatformMutex>  _mutex;
00200     qspi_bus_width_t _inst_width; //Bus width for Instruction phase
00201     qspi_bus_width_t _address_width; //Bus width for Address phase
00202     qspi_address_size_t _address_size;
00203     qspi_bus_width_t _alt_width; //Bus width for Alt phase
00204     qspi_alt_size_t _alt_size;
00205     qspi_bus_width_t _data_width; //Bus width for Data phase
00206     qspi_command_t _qspi_command; //QSPI Hal command struct
00207     unsigned int _num_dummy_cycles; //Number of dummy cycles to be used
00208     int _hz; //Bus Frequency
00209     int _mode; //SPI mode
00210     bool _initialized;
00211     PinName _qspi_io0, _qspi_io1, _qspi_io2, _qspi_io3, _qspi_clk, _qspi_cs; //IO lines, clock and chip select
00212 
00213 private:
00214     /* Private acquire function without locking/unlocking
00215      * Implemented in order to avoid duplicate locking and boost performance
00216      */
00217     bool _acquire(void);
00218     bool _initialize();
00219 
00220     /*
00221      * This function builds the qspi command struct to be send to Hal
00222      */
00223     inline void _build_qspi_command(int instruction, int address, int alt);
00224 #endif
00225 };
00226 
00227 } // namespace mbed
00228 
00229 #endif
00230 
00231 #endif