Kenji Arai / Mbed 2 deprecated Check_new_LIS3DH_lib

Check program for LIS3DH bug fixed rev.

Dependencies:   LIS3DH mbed

I fixed bugs in my library LIS3DH and updated it as Rev.7. This is a check program for LIS3DH lib.

Followings are PC console output data.

003854,new,[m/s2],-0.1079,+0.1177,+9.3457,[mg],   -10,   +14,  +957
003855,new,[m/s2],-0.0588,+0.0686,+9.3555,[mg],    -9,   +11,  +956
003856,new,[m/s2],-0.0686,+0.0883,+9.3163,[mg],   -11,    +8,  +953
003857,new,[m/s2],-0.0981,+0.1275,+9.3752,[mg],    -9,   +13,  +953
003858,new,[m/s2],-0.0981,+0.0294,+9.3457,[mg],   -13,   +10,  +953

In addition, you can see reg. contents.

LIS3DH ultra low-power high performance 3-axes 'nano' accelerometer
 STATUS_AUX=0xff
 OUT_ADC1_L=0x00, OUT_ADC1_H=0x00
 OUT_ADC2_L=0x00, OUT_ADC2_H=0x00
 OUT_ADC3_L=0x00, OUT_ADC3_H=0x00
 INT_COUNTER_REG=0x00
 WHO_AM_I=0x33
 TEMP_CFG_REG=0x00
 CTRL_REG1=0x47, CTRL_REG2=0x00, CTRL_REG3=0x00
 CTRL_REG4=0x08, CTRL_REG5=0x00, CTRL_REG6=0x00
 REFERENCE=0x00
 STATUS_REG=0xff
 OUT_X_L=0xc0, OUT_X_H=0xff
 OUT_Y_L=0x10, OUT_Y_H=0x00
 OUT_Z_L=0x60, OUT_Z_H=0x3b
 FIFO_CTRL_REG=0x00, FIFO_SRC_REG=0x20
 INT1_CFG=0x00, INT1_SOURCE=0x00, INT1_THS=0x00, INT1_DURATION=0x00
 CLICK_CFG=0x00, CLICK_SRC=0x00, CLICK_THS=0x00
 TIME_LIMIT=0x00, TIME_LATENCY=0x00, TIME_WINDOW=0x00

Here is meaning of data.

<Setting condition>
 STATUS_AUX=0xff
-> new data are avairable but all data are over-run condition
 OUT_ADC1_L=0x00, OUT_ADC1_H=0x00
 OUT_ADC2_L=0x00, OUT_ADC2_H=0x00
 OUT_ADC3_L=0x00, OUT_ADC3_H=0x00
-> all ADC data are Zero
 INT_COUNTER_REG=0x00
-> ?
 WHO_AM_I=0x33
-> I'm LIS3DH
 TEMP_CFG_REG=0x00
-> ADC: disabled, Temperature sensor (T): disabled
 CTRL_REG1=0x47
-> Data rate selection: 50Hz, Low power mode: disabled, XYZ axes: all enabled
 CTRL_REG2=0x00
-> High pass filter mode selection: normal, Filtered data selection: internal filter bypassed
High pass filter: bypassed
 CTRL_REG3=0x00
-> All kinds of interrupt: disabled
 CTRL_REG4=0x08
-> Block data update:continuos update, Big/little endian data selection: Data LSB/lower address
Full scale selection. default value: +/-2G, High resolution output mode: disabled
 CTRL_REG5=0x00
-> FIFO disable
 CTRL_REG6=0x00
-> ?
 REFERENCE=0x00
-> Reference value for Interrupt generation=0
 STATUS_REG=0xff
-> new data are avairable but all data are over-run condition
 OUT_X_L=0xc0, OUT_X_H=0xff
-> 0xffc0 -> -64/16 -> -4 
 OUT_Y_L=0x10, OUT_Y_H=0x00
-> 0x0010 -> 16/16 -> 1
 OUT_Z_L=0x60, OUT_Z_H=0x3b
-> 0x3b60 -> 15200/16 ->950
 FIFO_CTRL_REG=0x00
-> FIFO mode selection: bypassed
 FIFO_SRC_REG=0x20
-> FIFO: empty
 INT1_CFG=0x00, INT1_SOURCE=0x00, INT1_THS=0x00, INT1_DURATION=0x00
-> Interrupt related reg's are not used
 CLICK_CFG=0x00, CLICK_SRC=0x00, CLICK_THS=0x00
-> Click action: not used
 TIME_LIMIT=0x00, TIME_LATENCY=0x00, TIME_WINDOW=0x00
-> Click related reg's are nit used

Files at this revision

API Documentation at this revision

Revision 0:117c3daca107, committed 2015-12-12

Comitter:
kenjiArai
Date:
Sat Dec 12 06:17:47 2015 +0000
Commit message:
Check program for LIS3DH bug fixed rev.

Changed in this revision

LIS3DH.lib Show annotated file Show diff for this revision Revisions of this file
main.cpp Show annotated file Show diff for this revision Revisions of this file
mbed.bld Show annotated file Show diff for this revision Revisions of this file 
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/LIS3DH.lib	Sat Dec 12 06:17:47 2015 +0000
@@ -0,0 +1,1 @@
+http://mbed.org/users/kenjiArai/code/LIS3DH/#50ac3372def2

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/main.cpp	Sat Dec 12 06:17:47 2015 +0000
@@ -0,0 +1,102 @@
+/*
+ * mbed Application program for the mbed
+ *      LIS3DH ultra low-power high performance 3-axes “nano” accelerometer
+ *
+ * Copyright (c) 2014 Kenji Arai / JH1PJL
+ *  http://www.page.sannet.ne.jp/kenjia/index.html
+ *  http://mbed.org/users/kenjiArai/
+ *      Created: November  29th, 2015
+ *      Revised: December  12th, 2015
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
+ * INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE
+ * AND NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM,
+ * DAMAGES OR OTHER  LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
+ * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+//  Include ---------------------------------------------------------------------------------------
+#include    "mbed.h"
+#include    "LIS3DH.h"
+
+//  Definition ------------------------------------------------------------------------------------
+
+//  Object ----------------------------------------------------------------------------------------
+// com
+Serial      pc(USBTX, USBRX);      // Communication with Host
+I2C         i2c(D14,D15);
+// Acc
+LIS3DH      acc(i2c, LIS3DH_V_CHIP_ADDR, LIS3DH_DR_NR_LP_50HZ, LIS3DH_FS_2G);
+
+//  RAM -------------------------------------------------------------------------------------------
+float fa[3];    // Acc  0:X, 1:Y, 2:Z
+uint32_t n;
+
+//  ROM / Constant data ---------------------------------------------------------------------------
+
+//  Function prototypes ---------------------------------------------------------------------------
+void display_reg(void);
+
+//-------------------------------------------------------------------------------------------------
+//  Control Program
+//-------------------------------------------------------------------------------------------------
+int main(void) {
+    n = 1;
+    while (true) {
+#if OLD_REV  // defined in LIS3DH.h
+        acc.read_data(fa);
+        pc.printf("%06d,old,[m/s2], %+7.4f,%+7.4f,%+7.4f,", n++, fa[0], fa[1], fa[2]);
+        acc.read_mg_data(fa);
+        pc.printf("[g],%+7.4f,%+7.4f,%+7.4f \r\n", fa[0], fa[1], fa[2]);
+#else
+        acc.read_data(fa);
+        pc.printf("%06d,new,[m/s2],%+06.4f,%+06.4f,%+06.4f,", n++, fa[0], fa[1], fa[2]);
+        acc.read_mg_data(fa);
+        pc.printf("[mg],%+6.0f,%+6.0f,%+6.0f \r\n", fa[0], fa[1], fa[2]);
+#endif
+        wait(0.5);
+        if (n%25 == 0){
+            display_reg();
+        }
+    }
+}
+
+void display_reg(void){
+    pc.printf("LIS3DH ultra low-power high performance 3-axes 'nano' accelerometer\r\n");
+    pc.printf(" STATUS_AUX=0x%02x\r\n", acc.read_reg(LIS3DH_STATUS_REG_AUX));
+    pc.printf(" OUT_ADC1_L=0x%02x,", acc.read_reg(LIS3DH_OUT_ADC1_L));
+    pc.printf(" OUT_ADC1_H=0x%02x\r\n", acc.read_reg(LIS3DH_OUT_ADC1_H));
+    pc.printf(" OUT_ADC2_L=0x%02x,", acc.read_reg(LIS3DH_OUT_ADC2_L));
+    pc.printf(" OUT_ADC2_H=0x%02x\r\n", acc.read_reg(LIS3DH_OUT_ADC2_H));
+    pc.printf(" OUT_ADC3_L=0x%02x,", acc.read_reg(LIS3DH_OUT_ADC3_L));
+    pc.printf(" OUT_ADC3_H=0x%02x\r\n", acc.read_reg(LIS3DH_OUT_ADC3_H));
+    pc.printf(" INT_COUNTER_REG=0x%02x\r\n", acc.read_reg(LIS3DH_INT_COUNTER_REG));
+    pc.printf(" WHO_AM_I=0x%02x\r\n", acc.read_reg(LIS3DH_WHO_AM_I));
+    pc.printf(" TEMP_CFG_REG=0x%02x\r\n", acc.read_reg(LIS3DH_TEMP_CFG_REG));
+    pc.printf(" CTRL_REG1=0x%02x,", acc.read_reg(LIS3DH_CTRL_REG1));
+    pc.printf(" CTRL_REG2=0x%02x,", acc.read_reg(LIS3DH_CTRL_REG2));
+    pc.printf(" CTRL_REG3=0x%02x\r\n", acc.read_reg(LIS3DH_CTRL_REG3));
+    pc.printf(" CTRL_REG4=0x%02x,", acc.read_reg(LIS3DH_CTRL_REG4));
+    pc.printf(" CTRL_REG5=0x%02x,", acc.read_reg(LIS3DH_CTRL_REG5));
+    pc.printf(" CTRL_REG6=0x%02x\r\n", acc.read_reg(LIS3DH_CTRL_REG6));
+    pc.printf(" REFERENCE=0x%02x\r\n", acc.read_reg(LIS3DH_REFERENCE));
+    pc.printf(" STATUS_REG=0x%02x\r\n", acc.read_reg(LIS3DH_STATUS_REG));
+    pc.printf(" OUT_X_L=0x%02x,", acc.read_reg(LIS3DH_OUT_X_L));
+    pc.printf(" OUT_X_H=0x%02x\r\n", acc.read_reg(LIS3DH_OUT_X_H));
+    pc.printf(" OUT_Y_L=0x%02x,", acc.read_reg(LIS3DH_OUT_Y_L));
+    pc.printf(" OUT_Y_H=0x%02x\r\n", acc.read_reg(LIS3DH_OUT_Y_H));
+    pc.printf(" OUT_Z_L=0x%02x,", acc.read_reg(LIS3DH_OUT_Z_L));
+    pc.printf(" OUT_Z_H=0x%02x\r\n", acc.read_reg(LIS3DH_OUT_Z_H));
+    pc.printf(" FIFO_CTRL_REG=0x%02x,", acc.read_reg(LIS3DH_FIFO_CTRL_REG));
+    pc.printf(" FIFO_SRC_REG=0x%02x\r\n", acc.read_reg(LIS3DH_FIFO_SRC_REG));
+    pc.printf(" INT1_CFG=0x%02x,", acc.read_reg(LIS3DH_INT1_CFG));
+    pc.printf(" INT1_SOURCE=0x%02x,", acc.read_reg(LIS3DH_INT1_SOURCE));
+    pc.printf(" INT1_THS=0x%02x,", acc.read_reg(LIS3DH_INT1_THS));
+    pc.printf(" INT1_DURATION=0x%02x\r\n", acc.read_reg(LIS3DH_INT1_DURATION));
+    pc.printf(" CLICK_CFG=0x%02x,", acc.read_reg(LIS3DH_CLICK_CFG));
+    pc.printf(" CLICK_SRC=0x%02x,", acc.read_reg(LIS3DH_CLICK_SRC));
+    pc.printf(" CLICK_THS=0x%02x\r\n", acc.read_reg(LIS3DH_CLICK_THS));
+    pc.printf(" TIME_LIMIT=0x%02x,", acc.read_reg(LIS3DH_TIME_LIMIT));
+    pc.printf(" TIME_LATENCY=0x%02x,", acc.read_reg(LIS3DH_TIME_LATENCY));
+    pc.printf(" TIME_WINDOW=0x%02x\r\n", acc.read_reg(LIS3DH_TIME_WINDOW));
+}

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed.bld	Sat Dec 12 06:17:47 2015 +0000
@@ -0,0 +1,1 @@
+http://mbed.org/users/mbed_official/code/mbed/builds/165afa46840b
\ No newline at end of file