Diff: main.cpp

Revision:

0:1441b10e38a6

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/main.cpp	Thu Jan 04 03:42:09 2018 +0000
@@ -0,0 +1,85 @@
+#include "board_config.h"
+#include "radio_sensor.h"
+#include "sensors.h" //Sesing
+#include "status_led.h" //Displys the atatus of the sensor through LED
+
+
+#define MDOT_TIME_SLEEP (180) // Sleep time in seconds
+
+
+DigitalIn button(PIN_INPUT_BUTTON);
+#ifdef DEBUG_SERIAL_ENABLED
+// Note: Apparently MTSLog is dependant on the initialization of the debug serial port.
+Serial debug_serial(PIN_OUTPUT_DEBUG_UART_TX, PIN_OUTPUT_DEBUG_UART_RX, DEBUG_UART_BAUD);
+#endif
+
+
+void print_sensor_data(struct sensor_data_raw data);
+
+
+int main(void)
+{
+    struct sensor_data_raw data;
+
+
+    status_led_blink(STATUS_LED_POWER_ON);
+
+
+    sensors_init(); //Initializes teh ADS1115, sets the devises switch and signals to 0
+    radio_sensor_init(mts::MTSLog::DEBUG_LEVEL); //???
+
+
+    status_led_blink(STATUS_LED_CONNECTED);
+
+
+    while (true) {
+        sensors_read(&data);
+        
+        
+        // Print the sensor data to be transmitted.
+        print_sensor_data(data);
+
+
+        // Transmit the sensor data.
+        if(radio_sensor_transmit(data) == 0) {
+            data.reading_number++;
+            status_led_blink(STATUS_LED_RADIO_ACTIVITY);
+            logInfo("Successfully transmited sensor data.");
+        } else {
+            logError("Failed to transmit sensor data.");
+        }
+
+
+        // Set the wakeup pin, save the configuration of the pins and then configure them for low power mode.
+        dot->setWakePin(PIN_INPUT_BUTTON);
+        sleep_save_io();
+        sleep_configure_io();
+
+        // Send the MDot to sleep.
+        dot->sleep(MDOT_TIME_SLEEP, mDot::RTC_ALARM_OR_INTERRUPT, false);
+
+        // Restore the save pin configuration.
+        sleep_restore_io();
+
+        if(button.read() == 1) {
+            logDebug("Button press.");
+            status_led_blink(STATUS_LED_CHECK);
+        }
+    }
+}
+
+void print_sensor_data(struct sensor_data_raw data)
+{
+    logInfo("reading #:   %7u", data.reading_number);
+    logInfo("battery:     %7u", data.voltage_battery);
+    logInfo("signal 1-1:  %7u", data.voltage_wire[0]);
+    logInfo("signal 1-2:  %7u", data.voltage_wire[1]);
+    logInfo("signal 1-3:  %7u", data.voltage_wire[2]);
+    logInfo("signal 2-1:  %7u", data.voltage_wire[3]);
+    logInfo("signal 2-2:  %7u", data.voltage_wire[4]);
+    logInfo("signal 2-3:  %7u", data.voltage_wire[5]);
+    logInfo("signal 3-1:  %7u", data.voltage_wire[6]);
+    logInfo("signal 3-2:  %7u", data.voltage_wire[7]);
+    logInfo("signal 3-3:  %7u", data.voltage_wire[8]);
+    logInfo("temperature: %7i", data.temperature);
+}
\ No newline at end of file