mbed library sources: Modified to operate FRDM-KL25Z at 48MHz from internal 32kHz oscillator (nothing else changed).

Fork of mbed-src by mbed official

The only file that changed is: mbed-src-FLL48/targets/cmsis/TARGET_Freescale/TARGET_KL25Z/system_MKL25Z4.h

Revision:
9:0ce32e54c9a7
Parent:
8:4e25b8576136
Child:
10:3bc89ef62ce7
--- a/cpp/Ethernet.h	Thu May 30 16:59:31 2013 +0100
+++ /dev/null	Thu Jan 01 00:00:00 1970 +0000
@@ -1,170 +0,0 @@
-/* mbed Microcontroller Library
- * Copyright (c) 2006-2013 ARM Limited
- *
- * Licensed under the Apache License, Version 2.0 (the "License");
- * you may not use this file except in compliance with the License.
- * You may obtain a copy of the License at
- *
- *     http://www.apache.org/licenses/LICENSE-2.0
- *
- * Unless required by applicable law or agreed to in writing, software
- * distributed under the License is distributed on an "AS IS" BASIS,
- * WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
- * See the License for the specific language governing permissions and
- * limitations under the License.
- */
-#ifndef MBED_ETHERNET_H
-#define MBED_ETHERNET_H
-
-#include "platform.h"
-
-#if DEVICE_ETHERNET
-
-namespace mbed {
-
-/** An ethernet interface, to use with the ethernet pins.
- *
- * Example:
- * @code
- * // Read destination and source from every ethernet packet
- *
- * #include "mbed.h"
- *
- * Ethernet eth;
- *
- * int main() {
- *     char buf[0x600];
- *
- *     while(1) {
- *         int size = eth.receive();
- *         if(size > 0) {
- *             eth.read(buf, size);
- *             printf("Destination:  %02X:%02X:%02X:%02X:%02X:%02X\n",
- *                     buf[0], buf[1], buf[2], buf[3], buf[4], buf[5]);
- *             printf("Source: %02X:%02X:%02X:%02X:%02X:%02X\n",
- *                     buf[6], buf[7], buf[8], buf[9], buf[10], buf[11]);
- *         }
- *
- *         wait(1);
- *     }
- * }
- * @endcode
- */
-class Ethernet {
-
-public:
-
-    /** Initialise the ethernet interface.
-     */
-    Ethernet();
-
-    /** Powers the hardware down.
-     */
-    virtual ~Ethernet();
-
-    enum Mode {
-        AutoNegotiate,
-        HalfDuplex10,
-        FullDuplex10,
-        HalfDuplex100,
-        FullDuplex100
-    };
-
-    /** Writes into an outgoing ethernet packet.
-     *
-     *  It will append size bytes of data to the previously written bytes.
-     *
-     *  @param data An array to write.
-     *  @param size The size of data.
-     *
-     *  @returns
-     *   The number of written bytes.
-     */
-    int write(const char *data, int size);
-
-    /** Send an outgoing ethernet packet.
-     *
-     *  After filling in the data in an ethernet packet it must be send.
-     *  Send will provide a new packet to write to.
-     *
-     *  @returns
-     *    0 if the sending was failed,
-     *    1 if the package is successfully sent.
-     */
-    int send();
-
-    /** Recevies an arrived ethernet packet.
-     *
-     *  Receiving an ethernet packet will drop the last received ethernet packet
-     *  and make a new ethernet packet ready to read.
-     *  If no ethernet packet is arrived it will return 0.
-     *
-     *  @returns
-     *    0 if no ethernet packet is arrived,
-     *    or the size of the arrived packet.
-     */
-    int receive();
-
-    /** Read from an recevied ethernet packet.
-     *
-     *  After receive returnd a number bigger than 0it is
-     *  possible to read bytes from this packet.
-     *  Read will write up to size bytes into data.
-     *
-     *  It is possible to use read multible times.
-     *  Each time read will start reading after the last read byte before.
-     *
-     *  @returns
-     *  The number of byte read.
-     */
-    int read(char *data, int size);
-
-    /** Gives the ethernet address of the mbed.
-     *
-     *  @param mac Must be a pointer to a 6 byte char array to copy the ethernet address in.
-     */
-    void address(char *mac);
-
-    /** Returns if an ethernet link is pressent or not. It takes a wile after Ethernet initializion to show up.
-     *
-     *  @returns
-     *   0 if no ethernet link is pressent,
-     *   1 if an ethernet link is pressent.
-     *
-     * Example:
-     * @code
-     * // Using the Ethernet link function
-     * #include "mbed.h"
-     *
-     * Ethernet eth;
-     *
-     * int main() {
-     *     wait(1); // Needed after startup.
-     *     if (eth.link()) {
-     *          printf("online\n");
-     *     } else {
-     *          printf("offline\n");
-     *     }
-     * }
-     * @endcode
-     */
-    int link();
-
-    /** Sets the speed and duplex parameters of an ethernet link
-     *
-     * - AutoNegotiate      Auto negotiate speed and duplex
-     * - HalfDuplex10       10 Mbit, half duplex
-     * - FullDuplex10       10 Mbit, full duplex
-     * - HalfDuplex100      100 Mbit, half duplex
-     * - FullDuplex100      100 Mbit, full duplex
-     *
-     *  @param mode the speed and duplex mode to set the link to:
-     */
-    void set_link(Mode mode);
-};
-
-} // namespace mbed
-
-#endif
-
-#endif