Herson Bagay

Activity

Reply to Mbed memory - looks like its an 8 bit bus with a bunch of control pins. should not …
Herson Bagay - 07 Apr 2012
Reply to Mbed memory - which NAND flash are you using? any datasheet we can look at?
Herson Bagay - 07 Apr 2012
Reply to PWM Triggered Interrupt - Use the built in PWM controller for application such as this so you're CPU is …
Herson Bagay - 05 Apr 2012
Reply to Interrupt pwm motor control to read ultrasonic distance - if your PWM is in hardware, then there should not be any interruption whatsoever.
Herson Bagay - 28 Mar 2012
Reply to Sensor data (AnalogIn) to PC, via Ethernet. (fast, low latency)? - You cannot because you did not include any IP header after the Ethertype bytes. You …
Herson Bagay - 25 Mar 2012
Reply to Sensor data (AnalogIn) to PC, via Ethernet. (fast, low latency)? - as long as it is not flooded, your server and your office switch should be …
Herson Bagay - 24 Mar 2012
Reply to Sensor data (AnalogIn) to PC, via Ethernet. (fast, low latency)? - well, if you changed the destination mac to an unknown MAC address (it doesn't exist …
Herson Bagay - 24 Mar 2012
Reply to Sensor data (AnalogIn) to PC, via Ethernet. (fast, low latency)? - just try to use the actual server MAC though because there's a tendency that it …
Herson Bagay - 24 Mar 2012
Reply to -
Herson Bagay - 24 Mar 2012
Reply to Mbed to Mbed Communication - fastest way is through Ethernet, assuming both mbeds are on the same LAN easiest way …
Herson Bagay - 24 Mar 2012
Reply to -
Herson Bagay - 24 Mar 2012
Reply to Sensor data (AnalogIn) to PC, via Ethernet. (fast, low latency)? - try this and scope it on wireshark #include "mbed.h" Ethernet eth; char eth_txs_buffer[1536]; uint16_t packet_length; …
Herson Bagay - 24 Mar 2012
Reply to Sensor data (AnalogIn) to PC, via Ethernet. (fast, low latency)? - are the server and mbed on the same broadcast domain (i.e VLAN)? did you write …
Herson Bagay - 24 Mar 2012
Reply to Multiple SPI buses with interrupts - SPI or SSP0 is on DIP11 to 14 SSP1 is at DIP5 to 8 look …
Herson Bagay - 23 Mar 2012
Reply to Interrupt driven spi? - try this out, SPI on P0.15, P0.16, P0.17, P0.18 (check your mbed schematics for the …
Herson Bagay - 23 Mar 2012
Reply to Programming mbed - here's an example LPC_SC->PCONP |= 1<<2; LPC_SC->PCLKSEL0 |= 3<<4; look at the lpc17xx.h file for …
Herson Bagay - 18 Mar 2012
Reply to Use UART to send char/msg to PC sercial - heres a code that enables UART1 on pin 25 and 26. The mbed runs at …
Herson Bagay - 08 Sep 2011
Reply to How many library's cab you rub - the raw ethernet driver works very well in the mbed, but the http client/server implementation …
Herson Bagay - 07 Sep 2011
Reply to S/PDIF passthrough - Slow I/O? Noise? - scratch that, i just found out the EINTx pins are not broken out on the …
Herson Bagay - 04 Sep 2011
Reply to S/PDIF passthrough - Slow I/O? Noise? - did you try using high priority interrupts? have your input pin trigger an interrupt on …
Herson Bagay - 04 Sep 2011