Diff: VL6180x.h

Revision:

0:4a5d4b4a40c4

Child:

1:3ebf8893b7e0

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/VL6180x.h	Sun May 10 07:43:39 2015 +0000
@@ -0,0 +1,188 @@
+/******************************************************************************
+ * SFE_VL6180X.h
+ * Library for VL6180x time of flight range finder.
+ * Casey Kuhns @ SparkFun Electronics
+ * 10/29/2014
+ * https://github.com/sparkfun/
+ * 
+ * The VL6180x by ST micro is a time of flight range finder that
+ * uses pulsed IR light to determine distances from object at close
+ * range.  The average range of a sensor is between 0-200mm
+ * 
+ * In this file are the function prototypes in the VL6180x class
+ * 
+ * Resources:
+ * This library uses the Arduino Wire.h to complete I2C transactions.
+ * 
+ * Development environment specifics:
+ *  IDE: Arduino 1.0.5
+ *  Hardware Platform: Arduino Pro 3.3V/8MHz
+ *  VL6180x Breakout Version: 1.0
+ * 
+ * Some settings and initial values come from code written by Kris Winer
+ * VL6180X_t3 Basic Example Code
+ * by: Kris Winer
+ * date: September 1, 2014
+ * license: Beerware - Use this code however you'd like. If you 
+ * find it useful you can buy me a beer some time.
+ * 
+ * This code is beerware. If you see me (or any other SparkFun employee) at the
+ * local pub, and you've found our code helpful, please buy us a round!
+ * 
+ * Distributed as-is; no warranty is given.
+ ******************************************************************************/
+#include "mbed.h"
+#ifndef VL6180x_h
+#define VL6180x_h
+
+#define VL6180x_FAILURE_RESET  -1
+
+#define VL6180X_IDENTIFICATION_MODEL_ID              0x0000
+#define VL6180X_IDENTIFICATION_MODEL_REV_MAJOR       0x0001
+#define VL6180X_IDENTIFICATION_MODEL_REV_MINOR       0x0002
+#define VL6180X_IDENTIFICATION_MODULE_REV_MAJOR      0x0003
+#define VL6180X_IDENTIFICATION_MODULE_REV_MINOR      0x0004
+#define VL6180X_IDENTIFICATION_DATE                  0x0006 //16bit value
+#define VL6180X_IDENTIFICATION_TIME                  0x0008 //16bit value
+
+#define VL6180X_SYSTEM_MODE_GPIO0                    0x0010
+#define VL6180X_SYSTEM_MODE_GPIO1                    0x0011
+#define VL6180X_SYSTEM_HISTORY_CTRL                  0x0012
+#define VL6180X_SYSTEM_INTERRUPT_CONFIG_GPIO         0x0014
+#define VL6180X_SYSTEM_INTERRUPT_CLEAR               0x0015
+#define VL6180X_SYSTEM_FRESH_OUT_OF_RESET            0x0016
+#define VL6180X_SYSTEM_GROUPED_PARAMETER_HOLD        0x0017
+
+#define VL6180X_SYSRANGE_START                       0x0018
+#define VL6180X_SYSRANGE_THRESH_HIGH                 0x0019
+#define VL6180X_SYSRANGE_THRESH_LOW                  0x001A
+#define VL6180X_SYSRANGE_INTERMEASUREMENT_PERIOD     0x001B
+#define VL6180X_SYSRANGE_MAX_CONVERGENCE_TIME        0x001C
+#define VL6180X_SYSRANGE_CROSSTALK_COMPENSATION_RATE 0x001E
+#define VL6180X_SYSRANGE_CROSSTALK_VALID_HEIGHT      0x0021
+#define VL6180X_SYSRANGE_EARLY_CONVERGENCE_ESTIMATE  0x0022
+#define VL6180X_SYSRANGE_PART_TO_PART_RANGE_OFFSET   0x0024
+#define VL6180X_SYSRANGE_RANGE_IGNORE_VALID_HEIGHT   0x0025
+#define VL6180X_SYSRANGE_RANGE_IGNORE_THRESHOLD      0x0026
+#define VL6180X_SYSRANGE_MAX_AMBIENT_LEVEL_MULT      0x002C
+#define VL6180X_SYSRANGE_RANGE_CHECK_ENABLES         0x002D
+#define VL6180X_SYSRANGE_VHV_RECALIBRATE             0x002E
+#define VL6180X_SYSRANGE_VHV_REPEAT_RATE             0x0031
+
+#define VL6180X_SYSALS_START                         0x0038
+#define VL6180X_SYSALS_THRESH_HIGH                   0x003A
+#define VL6180X_SYSALS_THRESH_LOW                    0x003C
+#define VL6180X_SYSALS_INTERMEASUREMENT_PERIOD       0x003E
+#define VL6180X_SYSALS_ANALOGUE_GAIN                 0x003F
+#define VL6180X_SYSALS_INTEGRATION_PERIOD            0x0040
+
+#define VL6180X_RESULT_RANGE_STATUS                  0x004D
+#define VL6180X_RESULT_ALS_STATUS                    0x004E
+#define VL6180X_RESULT_INTERRUPT_STATUS_GPIO         0x004F
+#define VL6180X_RESULT_ALS_VAL                       0x0050
+#define VL6180X_RESULT_HISTORY_BUFFER                0x0052 
+#define VL6180X_RESULT_RANGE_VAL                     0x0062
+#define VL6180X_RESULT_RANGE_RAW                     0x0064
+#define VL6180X_RESULT_RANGE_RETURN_RATE             0x0066
+#define VL6180X_RESULT_RANGE_REFERENCE_RATE          0x0068
+#define VL6180X_RESULT_RANGE_RETURN_SIGNAL_COUNT     0x006C
+#define VL6180X_RESULT_RANGE_REFERENCE_SIGNAL_COUNT  0x0070
+#define VL6180X_RESULT_RANGE_RETURN_AMB_COUNT        0x0074
+#define VL6180X_RESULT_RANGE_REFERENCE_AMB_COUNT     0x0078
+#define VL6180X_RESULT_RANGE_RETURN_CONV_TIME        0x007C
+#define VL6180X_RESULT_RANGE_REFERENCE_CONV_TIME     0x0080
+
+#define VL6180X_READOUT_AVERAGING_SAMPLE_PERIOD      0x010A
+#define VL6180X_FIRMWARE_BOOTUP                      0x0119
+#define VL6180X_FIRMWARE_RESULT_SCALER               0x0120
+#define VL6180X_I2C_SLAVE_DEVICE_ADDRESS             0x0212
+#define VL6180X_INTERLEAVED_MODE_ENABLE              0x02A3
+
+
+enum vl6180x_als_gain { //Data sheet shows gain values as binary list
+
+GAIN_20 = 0, // Actual ALS Gain of 20
+GAIN_10,     // Actual ALS Gain of 10.32
+GAIN_5,      // Actual ALS Gain of 5.21
+GAIN_2_5,    // Actual ALS Gain of 2.60
+GAIN_1_67,   // Actual ALS Gain of 1.72
+GAIN_1_25,   // Actual ALS Gain of 1.28
+GAIN_1 ,     // Actual ALS Gain of 1.01
+GAIN_40,     // Actual ALS Gain of 40
+
+};
+
+struct VL6180xIdentification
+{
+  uint8_t idModel;
+  uint8_t idModelRevMajor;
+  uint8_t idModelRevMinor;
+  uint8_t idModuleRevMajor;
+  uint8_t idModuleRevMinor;
+  uint16_t idDate;
+  uint16_t idTime;
+};
+
+class VL6180x
+{
+public: 
+  //Initalize library with default address
+  /**
+  * VL6180x constructor
+  *
+  * @param sda SDA pin
+  * @param sdl SCL pin
+  * @param addr addr of the I2C peripheral
+  */
+  VL6180x(PinName sda, PinName scl, uint8_t addr);
+  /**
+  * VL6180x destructor
+  */
+  ~VL6180x();
+  //Send mandatory settings as stated in ST datasheet.
+  // http://www.st.com/st-web-ui/static/active/en/resource/technical/document/application_note/DM00122600.pdf (Section 1.3)
+  uint8_t VL6180xInit(void);
+  // Use default settings from ST data sheet section 9.
+  // http://www.st.com/st-web-ui/static/active/en/resource/technical/document/application_note/DM00122600.pdf
+  void VL6180xDefautSettings(void);
+
+  // Get Range distance in (mm)
+  uint8_t getDistance();
+  // Get ALS level in Lux
+  float getAmbientLight(vl6180x_als_gain VL6180X_ALS_GAIN);
+
+  //Load structure provided by the user with identification info
+  //Structure example:
+  // struct VL6180xIdentification
+  //  {
+  //   uint8_t idModel;
+  //   uint8_t idModelRevMajor;
+  //   uint8_t idModelRevMinor;
+  //   uint8_t idModuleRevMajor;
+  //   uint8_t idModuleRevMinor;
+  //   uint16_t idDate;
+  //   uint16_t idTime;
+  //   };
+  void getIdentification(struct VL6180xIdentification *temp);
+
+  //Change the default address of the device to allow multiple
+  //sensors on the bus.  Can use up to 127 sensors. New address
+  //is saved in non-volatile device memory.
+  uint8_t changeAddress(uint8_t old_address, uint8_t new_address);
+
+
+private:
+  //Store address given when the class is initialized.
+  //This value can be changed by the changeAddress() function
+  I2C m_i2c;
+  int m_addr;
+  uint8_t VL6180x_getRegister(uint16_t registerAddr);
+  uint16_t VL6180x_getRegister16bit(uint16_t registerAddr);
+
+  void VL6180x_setRegister(uint16_t registerAddr, uint8_t data);
+  void VL6180x_setRegister16bit(uint16_t registerAddr, uint16_t data);
+
+
+};
+
+#endif