File content as of revision 0:bf7b9fba3924:

 ******************** (C) COPYRIGHT 2010 NXPSemiconductors *******************
 * @file    SPI\sc16is750_int\abstract.txt 
 * @author  NXP MCU SW Application Team
 * @version 2.0
 * @date    
 * @brief   Description of the SPI SC16IS750 Interrupt example.
 ******************************************************************************
 * Software that is described herein is for illustrative purposes only
 * which provides customers with programming information regarding the
 * products. This software is supplied "AS IS" without any warranties.
 * NXP Semiconductors assumes no responsibility or liability for the
 * use of the software, conveys no license or title under any patent,
 * copyright, or mask work right to the product. NXP Semiconductors
 * reserves the right to make changes in the software without
 * notification. NXP Semiconductors also make no representation or
 * warranty that such application will be suitable for the specified
 * use without further testing or modification.
 ******************************************************************************
  
@Example description:
	Purpose:
		This example describes how to use SPI in interrupt mode to communicate 
		with SC16IS750/760 Demo Board.
	Process:
		SPI configuration:
			- CPHA = 0: data is sampled on the first clock edge of SCK.
			- CPOL = 0: SCK is active high
			- Clock rate = 1MHz
			- LSBF = 0: SPI data is transferred MSB first 
			- BITS = 8: 8 bits per transfer
			- MSTR = 1: SPI operates in Master mode
		First, SPI send commands to reset, config direction SC16IS740 chip in interrupt mode.
		Start to use SPI polling mode to handle SC16IS740 board.
		On serial display:
		- Press 'r' to print menu
		- Press '1': send 0x00 value to IOStat register to turn on 8 LEDs on SC16IS740 board.
		- Press '2': send 0xFF value to IOStat register to turn off 8 LEDs on SC16IS740 board.
		
		(Pls see two pdf file:
			- SC16IS740_750_760_6.pdf
			- schematics.sc16is750.demo.board.pdf
		for more information about SC16IS740 board)

@Directory contents:
	\EWARM: includes EWARM (IAR) project and configuration files
	\Keil:	includes RVMDK (Keil)project and configuration files 
	
	lpc17xx_libcfg.h: Library configuration file - include needed driver library for this example 
	makefile: Example's makefile (to build with GNU toolchain)
	spi_interrupt_test.c: Main program
	SC16IS740_750_760_6.pdf: SC16IS740_750_760_6's datasheet file
	schematics.sc16is750.demo.board.pdf: SC16IS750 board's schematic file

@How to run:
	Hardware configuration:		
		This example was tested on:
			Keil MCB1700 with LPC1768 vers.1
				These jumpers must be configured as following:
				- VDDIO: ON
				- VDDREGS: ON 
				- VBUS: ON
				- Remain jumpers: OFF
			IAR LPC1768 KickStart vers.A
				These jumpers must be configured as following:
				- PWR_SEL: depend on power source
				- DBG_EN : ON
				- Remain jumpers: OFF
				
		SC16IS750 board:
			 	These jumpers must be configured as following:
			 	- JP2: 2-3 (SPI)
			 	- JP16: 2-3 (hard reset)
			 	- Remain jumper: OFF
			
		SPI connection:
			- P0.15 - SCK on eval board connects to SCLK on SC16IS750 board
	 		- P0.16 - SSEL on eval board connects to /CS on SC16IS750 board (used as GPIO)
	  		- P0.17 - MISO on eval board connects to MISO on SC16IS750 board
	  		- P0.18 - MOSI on eval board connects to MOSI on SC16IS750 board
			Common power source 3.3V and ground must be connected together between two board.
	  			
	Serial display configuration: (e.g: TeraTerm, Hyperterminal, Flash Magic...) 
		– 115200bps 
		– 8 data bit 
		– No parity 
		– 1 stop bit 
		– No flow control 
	
	Running mode:
		This example can run on RAM/ROM mode.
					
		Note: If want to burn hex file to board by using Flash Magic, these jumpers need
		to be connected:
			- MCB1700 with LPC1768 ver.1:
				+ RST: ON
				+ ISP: ON
			- IAR LPC1768 KickStart vers.A:
				+ RST_E: ON
				+ ISP_E: ON
		
		(Please reference "LPC1000 Software Development Toolchain" - chapter 4 "Creating and working with
		LPC1000CMSIS project" for more information)
	
	Step to run:
		- Step 1: Build example.
		- Step 2: Burn hex file into board (if run on ROM mode) 
		- Step 5: Connect UART0 on board to COM port on your computer
		- Step 6: Configure hardware, connect this board with SC16IS750 board as above instruction 
		- Step 7: Configure serial display as above instruction
		- Step 8: Run example and handle SPI transfer via serial display
				+ Press '1' to turn on 8 LEDs on SC16IS750 board
				+ Press '2' to turn off 8 LEDs on SC16IS750 board
				
		(Pls see "LPC17xx Example Description" document - chapter "Examples > SPI > sc16is750_int" 
		for more details)
		
@Tip:
	- Open \EWARM\*.eww project file to run example on IAR
	- Open \RVMDK\*.uvproj project file to run example on Keil