Diff: SSP/sc16is750_int/abstract.h

Revision:

0:bf7b9fba3924

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/SSP/sc16is750_int/abstract.h	Sun Mar 20 05:38:56 2011 +0000
@@ -0,0 +1,117 @@
+ ******************** (C) COPYRIGHT 2010 NXPSemiconductors *******************
+ * @file    SSP\sc16is750_int\abstract.txt 
+ * @author  NXP MCU SW Application Team
+ * @version 2.0
+ * @date    
+ * @brief   Description of the SSP SC16IS750 Interrupt example.
+ ******************************************************************************
+ * Software that is described herein is for illustrative purposes only
+ * which provides customers with programming information regarding the
+ * products. This software is supplied "AS IS" without any warranties.
+ * NXP Semiconductors assumes no responsibility or liability for the
+ * use of the software, conveys no license or title under any patent,
+ * copyright, or mask work right to the product. NXP Semiconductors
+ * reserves the right to make changes in the software without
+ * notification. NXP Semiconductors also make no representation or
+ * warranty that such application will be suitable for the specified
+ * use without further testing or modification.
+ ******************************************************************************
+  
+@Example description:
+	Purpose:
+		This example describes how to use SSP in interrupt mode to communicate 
+		with SC16IS750/760 Demo Board.
+	Process:
+		SSP configuration:
+			- CPHA = 0: data is sampled on the first clock edge of SCK.
+			- CPOL = 0: SCK is active high
+			- Clock rate = 1MHz
+			- DSS = 8: 8 bits per transfer
+			- MSTR = 1: SSP operates in Master mode
+			- FRF= 0: SPI Frame format
+		First, SSP send commands to reset, config direction SC16IS740 chip in interrupt mode.
+		Start to use SSP polling mode to handle SC16IS740 board.
+		On serial display:
+		- Press 'r' to print menu
+		- Press '1': send 0x00 value to IOStat register to turn on 8 LEDs on SC16IS740 board.
+		- Press '2': send 0xFF value to IOStat register to turn off 8 LEDs on SC16IS740 board.
+		
+		(Pls see two pdf file at SPI\sc16is750_int:
+			- SC16IS740_750_760_6.pdf
+			- schematics.sc16is750.demo.board.pdf
+		for more information about SC16IS740 board)
+
+@Directory contents:
+	\EWARM: includes EWARM (IAR) project and configuration files
+	\Keil:	includes RVMDK (Keil)project and configuration files 
+	
+	lpc17xx_libcfg.h: Library configuration file - include needed driver library for this example 
+	makefile: Example's makefile (to build with GNU toolchain)
+	sc16is750_int.c: Main program
+
+@How to run:
+	Hardware configuration:		
+		This example was tested on:
+			Keil MCB1700 with LPC1768 vers.1
+				These jumpers must be configured as following:
+				- VDDIO: ON
+				- VDDREGS: ON 
+				- VBUS: ON
+				- Remain jumpers: OFF
+			IAR LPC1768 KickStart vers.A
+				These jumpers must be configured as following:
+				- PWR_SEL: depend on power source
+				- DBG_EN : ON
+				- Remain jumpers: OFF
+		
+		SC16IS750 board:
+			 	These jumpers must be configured as following:
+			 	- JP2: 2-3 (SPI)
+			 	- JP16: 2-3 (hard reset)
+			 	- Remain jumper: OFF
+			
+		SPI connection:
+			- P0.15 - SCK on eval board connects to SCLK on SC16IS750 board
+	 		- P0.16 - SSEL on eval board connects to /CS on SC16IS750 board (used as GPIO)
+	  		- P0.17 - MISO on eval board connects to MISO on SC16IS750 board
+	  		- P0.18 - MOSI on eval board connects to MOSI on SC16IS750 board
+			Common power source 3.3V and ground must be connected together between two board.
+	  			
+	Serial display configuration: (e.g: TeraTerm, Hyperterminal, Flash Magic...) 
+		– 115200bps 
+		– 8 data bit 
+		– No parity 
+		– 1 stop bit 
+		– No flow control 
+	
+	Running mode:
+		This example can run on RAM/ROM mode.
+					
+		Note: If want to burn hex file to board by using Flash Magic, these jumpers need
+		to be connected:
+			- MCB1700 with LPC1768 ver.1:
+				+ RST: ON
+				+ ISP: ON
+			- IAR LPC1768 KickStart vers.A:
+				+ RST_E: ON
+				+ ISP_E: ON
+		
+		(Please reference "LPC1000 Software Development Toolchain" - chapter 4 "Creating and working with
+		LPC1000CMSIS project" for more information)
+	
+	Step to run:
+		- Step 1: Build example.
+		- Step 2: Burn hex file into board (if run on ROM mode) 
+		- Step 5: Connect UART0 on board to COM port on your computer
+		- Step 6: Configure hardware, connect this board with SC16IS750 board as above instruction 
+		- Step 7: Configure serial display as above instruction
+		- Step 8: Run example and handle SSP transfer via serial display
+				+ Press '1' to turn on 8 LEDs on SC16IS750 board
+				+ Press '2' to turn off 8 LEDs on SC16IS750 board
+				
+		(Pls see "LPC17xx Example Description" document - chapter "Examples > SSP > sc16is750_int" 
+		for more details)
+		
+@Tip:
+	- Open \EWARM\*.eww project file to run example on IAR
+	- Open \RVMDK\*.uvproj project file to run example on Keil
\ No newline at end of file