Diff: CAN/CAN_LedControl/abstract.h

Revision:

0:bf7b9fba3924

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/CAN/CAN_LedControl/abstract.h	Sun Mar 20 05:38:56 2011 +0000
@@ -0,0 +1,89 @@
+ ******************** (C) COPYRIGHT 2010 NXPSemiconductors *******************
+ * @file    CAN\CAN_LedControl\abstract.txt 
+ * @author  NXP MCU SW Application Team
+ * @version 2.0
+ * @date    
+ * @brief   Description of the CAN Led Control example.
+ ******************************************************************************
+ * Software that is described herein is for illustrative purposes only
+ * which provides customers with programming information regarding the
+ * products. This software is supplied "AS IS" without any warranties.
+ * NXP Semiconductors assumes no responsibility or liability for the
+ * use of the software, conveys no license or title under any patent,
+ * copyright, or mask work right to the product. NXP Semiconductors
+ * reserves the right to make changes in the software without
+ * notification. NXP Semiconductors also make no representation or
+ * warranty that such application will be suitable for the specified
+ * use without further testing or modification.
+ ******************************************************************************
+  
+@Example description:
+	Purpose:
+		This example describes how to use CAN frames to control LED display.
+	Process:
+		Using 2 CAN peripheral CAN1 and CAN2 to test CAN operation.
+		Two CAN used in bypass mode.
+		User will enter LED display value on serial display and this value will be saved
+		in TXMsg, this message will be sent from CAN1 to CAN2.
+		When CAN2 receive this message, it will display LEDs according to value in this 
+		message.
+			
+@Directory contents:
+	\EWARM: includes EWARM (IAR) project and configuration files
+	\Keil:	includes RVMDK (Keil)project and configuration files 
+	 
+	lpc17xx_libcfg.h: Library configuration file - include needed driver library for this example 
+	makefile: Example's makefile (to build with GNU toolchain)
+	can_ledcontrol.c: Main program
+
+@How to run:
+	Hardware configuration:		
+		This example was tested only on:
+			Keil MCB1700 with LPC1768 vers.1
+				These jumpers must be configured as following:
+				- VDDIO: ON
+				- VDDREGS: ON 
+				- VBUS: ON
+				- Remain jumpers: OFF
+				
+		CAN connection:
+			- CAN1-Pin2 connects to CAN2-Pin2 (CAN-L)
+			- CAN1-Pin7 connects to CAN2-Pin7 (CAN-H)
+				
+		Serial display configuration:(e.g: TeraTerm, Hyperterminal, Flash Magic...) 
+			– 115200bps 
+			– 8 data bit 
+			– No parity 
+			– 1 stop bit 
+			– No flow control 
+	
+	Running mode:
+		This example can run on RAM/ROM mode.
+					
+		Note: If want to burn hex file to board by using Flash Magic, these jumpers need
+		to be connected:
+			- MCB1700 with LPC1768 ver.1:
+				+ RST: ON
+				+ ISP: ON
+			- IAR LPC1768 KickStart vers.A:
+				+ RST_E: ON
+				+ ISP_E: ON
+		
+		(Please reference "LPC1000 Software Development Toolchain" - chapter 4 "Creating and working with
+		LPC1000CMSIS project" for more information)
+	
+	Step to run:
+		- Step 1: Build example.
+		- Step 2: Burn hex file into board (if run on ROM mode)
+		- Step 3: Connect UART0 on this board to COM port on your computer
+		- Step 4: Configure hardware and serial display as above instruction 
+		- Step 5: Run example:
+			- Press LED value on serial display. This value should be in range: 0x00 - 0xFF
+			- See LED displaying on board.
+			
+		(Pls see "LPC17xx Example Description" document - chapter "Examples > CAN > CAN_LedControl"
+		for more details)
+		
+@Tip:
+	- Open \EWARM\*.eww project file to run example on IAR
+	- Open \RVMDK\*.uvproj project file to run example on Keil
\ No newline at end of file