Revision 0:2a4e076aeefa, committed 2017-12-17

Comitter:

emcu

Date:

Sun Dec 17 22:35:50 2017 +0000

Commit message:

Simple test for RC motor.

Changed in this revision

diff -r 000000000000 -r 2a4e076aeefa main.cpp
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/main.cpp	Sun Dec 17 22:35:50 2017 +0000
@@ -0,0 +1,178 @@
+#include "mbed.h"
+
+/*
+ By www.emcu.eu
+ Date December 2018
+ Simple test for RC motor
+ Version 1.0
+ Tested on the NUCLEO-F411RE and MG996R RC motor
+ 
+ For make this example you must use a NUCLEO board (we tested this example on
+    NUCLEO-F411RE) and connect it the components below:
+ A potentiometer - Connect it to 3,3v and GND and the central pin of the 
+    potentiometer must connect to A5 (PA_10).
+ A RC motor - Connect the BLACK wire to GND, RED wire to 5v and 
+    ORANGE wire to D2 (PC_0).
+
+ For more info see here:
+ http://www.emcu.eu/test-board-for-rc-motors
+ 
+ For use this example turn the potentiometer all to right and you must see the motor that move to right and a LED that flash.
+ If you move the potentiometer all to left you must see the motor that move left.
+ If you move the potentiometer in the middle position the RC motor is in stop and the LED flash fast.
+ If the potentiometer is in the middle and you press Blue button you start an automatic sequence.
+ 
+ For see the message from the SW open TeraTerm (terminal emulation) and configure it to: 8N1
+ 
+ Tested on Servo Motor:
+ MG996R - http://www.electronicoscaldas.com/datasheet/MG996R_Tower-Pro.pdf
+ 
+ RED    - + Vcc from 4,5 to 7,2V
+ BLACK  - GND
+ ORANGE - PWM
+ 
+  Duty - example: 1.9 (mS)
+  \  / 
+   \/
+   __
+__|  |_____________
+     ... 20mS......
+     
+ For rotate to right use value 1 for Duty
+ For rotate to left use value 5 for Duty
+ 
+*/
+
+AnalogIn adc_chA5(PC_0);
+DigitalOut Drive(PA_10);  
+DigitalOut led(LED1);
+DigitalIn mybutton(USER_BUTTON);
+
+#define Right   1 // Move to Right -> DESTRA   or DX
+#define Left    5 // Move to LEFT  <- SINISTRA or SX
+
+void Move(double);
+void Seq1(int n);
+void Seq2(void);
+
+int main()
+{
+    float Pot = 0;
+    int Movimento = 1;
+    
+    printf("\n\r STM32 RC motor test ver.1.0\n\r");
+    
+    Pot=adc_chA5;
+    
+    while(1) 
+    {
+        led = !led;
+        wait(0.1);
+        
+        Pot = adc_chA5;
+        Pot = Pot * 3300; // Change the value to be in the 0 to 3300 range
+        Movimento = Pot/1000;
+        printf(" 1 - Val.Pot %.0f mV - Movimento %d \n\r",Pot,Movimento);
+        
+        if(Pot>=1000 & Pot<=2900)
+        {
+            printf("\n\r *** RC motor stopped - Press Blue button for automatic sequence ***\n\r");
+            led = 0;
+            if (mybutton == 0)
+                Seq2();
+        }
+        else
+        {
+            if (Movimento <= 1)
+                Movimento = 1;
+            else
+                Movimento = 5;
+            printf(" 2 - Val.Pot %.0f mV - Movimento %d \n\r",Pot,Movimento);
+            Seq1(Movimento);
+            wait(1);
+        }    
+        
+        wait(0.2);   
+    }
+}
+
+void Move(double ON)
+{ 
+Drive=1;
+wait_ms(ON);
+Drive=0;
+wait_ms(25);
+}
+
+
+
+void Seq1(int n)
+{
+    if (n<=1)
+    {
+        n=5;
+        printf("\n\rMove to RIGHT ->\n\r");
+    }
+    else
+    {
+        n=1;
+        printf("\n\rMove to LEFT  <-\n\r");     
+    }
+    Move(n);
+}
+
+void Seq2(void)
+{
+    int n=0;
+    
+    printf("\n\rSequ n.2\n\r");
+    led = 1;
+    
+    printf("Move to 20 times to <-\n\r");
+    for(n=0; n<20; n++)
+        Move(Left);
+    wait(0.3);
+    printf("Move to 20 times to ->\n\r");
+    for(n=0; n<20; n++)
+        Move(Right);    
+    wait(0.3);
+    
+    printf("Move to 8 times to <-\n\r");
+    for(n=0; n<8; n++)
+        Move(Left);
+    wait(0.3);    
+    printf("Move to 5 times to ->\n\r");
+    for(n=0; n<5; n++)
+        Move(Right);
+    wait(0.3);     
+
+    printf("Move to 3 times to <-\n\r");
+    for(n=0; n<3; n++)
+        Move(Left);
+    wait(0.3);    
+    printf("Move to 3 times to ->\n\r");
+    for(n=0; n<3; n++)
+        Move(Right);
+    wait(0.3);     
+    
+    printf("Move to 2 times to <-\n\r");
+    for(n=0; n<2; n++)
+        Move(Left);
+    wait(0.3);    
+    printf("Move to 2 times to ->\n\r");
+    for(n=0; n<2; n++)
+        Move(Right);
+    wait(0.3);     
+
+    printf("Move to 1 times to <-\n\r");
+    for(n=0; n<1; n++)
+        Move(Left);
+    wait(0.3);    
+    printf("Move to 1 times to ->\n\r");
+    for(n=0; n<1; n++)
+        Move(Right);
+    wait(0.3);     
+    
+    printf("END - Seq n.2\n\r");
+    led = 0;
+}

diff -r 000000000000 -r 2a4e076aeefa mbed.bld
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/mbed.bld	Sun Dec 17 22:35:50 2017 +0000
@@ -0,0 +1,1 @@
+http://mbed.org/users/mbed_official/code/mbed/builds/e7ca05fa8600
\ No newline at end of file