File content as of revision 8:b08ec94d9e9f:

#include "mbed.h"
#include <cctype>
#include <string>
#include "SerialBuffered.h"
#include "HTS221.h"
#include "config_me.h"
#include "wnc_control.h"
#include "sensors.h"

// comment out the following line if color is not supported on the terminal
#define USE_COLOR
#ifdef USE_COLOR
 #define BLK "\033[30m"
 #define RED "\033[31m"
 #define GRN "\033[32m"
 #define YEL "\033[33m"
 #define BLU "\033[34m"
 #define MAG "\033[35m"
 #define CYN "\033[36m"
 #define WHT "\033[37m"
 #define DEF "\033[39m"
#else
 #define BLK
 #define RED
 #define GRN
 #define YEL
 #define BLU
 #define MAG
 #define CYN
 #define WHT
 #define DEF
#endif

#define MDM_DBG_OFF                             0
#define MDM_DBG_AT_CMDS                         (1 << 0)
int mdm_dbgmask = MDM_DBG_OFF;

Serial         pc(USBTX, USBRX);
SerialBuffered mdm(PTD3, PTD2, 128);
DigitalOut     led_red(LED_RED);
DigitalOut     led_green(LED_GREEN);

DigitalOut  mdm_uart2_rx_boot_mode_sel(PTC17);  // on powerup, 0 = boot mode, 1 = normal boot
DigitalOut  mdm_power_on(PTB9);                 // 0 = turn modem on, 1 = turn modem off (should be held high for >5 seconds to cycle modem)
DigitalOut  mdm_wakeup_in(PTC2);                // 0 = let modem sleep, 1 = keep modem awake -- Note: pulled high on shield

DigitalOut  shield_3v3_1v8_sig_trans_ena(PTC4); // 0 = disabled (all signals high impedence, 1 = translation active
DigitalOut  mdm_uart1_cts(PTD0);

#define TOUPPER(a) (a) //toupper(a)

const char ok_str[] = "OK";
const char error_str[] = "ERROR";

#define MDM_OK                                  0
#define MDM_ERR_TIMEOUT                         -1

#define MAX_AT_RSP_LEN                          255

ssize_t mdm_getline(char *buff, size_t size, int timeout_ms) {
    int cin = -1;
    int cin_last;
    
    if (NULL == buff || size == 0) {
        return -1;
    }

    size_t len = 0;
    Timer timer;
    timer.start();
    while ((len < (size-1)) && (timer.read_ms() < timeout_ms)) {
        if (mdm.readable()) {
            cin_last = cin;
            cin = mdm.getc();
            if (isprint(cin)) {
                buff[len++] = (char)cin;
                continue;
            } else if (('\r' == cin_last) && ('\n' == cin)) {
                break;
            }
        }
        wait_ms(1);
    }
    buff[len] = (char)NULL;
    
    return len;
}

int mdm_sendAtCmd(const char *cmd, const char **rsp_list, int timeout_ms) {
    if (cmd && strlen(cmd) > 0) {
        if (mdm_dbgmask & MDM_DBG_AT_CMDS) {
            printf(MAG "ATCMD: " DEF "--> " GRN "%s" DEF "\n", cmd);
        }
        mdm.printf("%s\r\n", cmd);
    }
    
    if (rsp_list) {
        Timer   timer;
        char    rsp[MAX_AT_RSP_LEN+1];
        int     len;
        
        timer.start();
        while (timer.read_ms() < timeout_ms) {
            len = mdm_getline(rsp, sizeof(rsp), timeout_ms - timer.read_ms());
            
            if (len < 0)
                return MDM_ERR_TIMEOUT;

            if (len == 0)
                continue;
                
            if (mdm_dbgmask & MDM_DBG_AT_CMDS) {
                printf(MAG "ATRSP: " DEF "<-- " CYN "%s" DEF "\n", rsp);
            }
        
            if (rsp_list) {
                int rsp_idx = 0;
                while (rsp_list[rsp_idx]) {
                    if (strcasecmp(rsp, rsp_list[rsp_idx]) == 0) {
                        return rsp_idx;
                    }
                    rsp_idx++;
                }
            }
        }
        return MDM_ERR_TIMEOUT;
    }
    return MDM_OK;
}

int mdm_init(void) {
    // disable signal level translator
    shield_3v3_1v8_sig_trans_ena = 0;

    // power modem on //off
    mdm_power_on = 0; //1;
    
    // insure modem boots into normal operating mode
    // and does not go to sleep when powered on
    mdm_uart2_rx_boot_mode_sel = 1;
    mdm_wakeup_in = 1;
    
    // initialze comm with the modem
    mdm.baud(115200);
    // clear out potential garbage
    while (mdm.readable())
      mdm.getc();

    mdm_uart1_cts = 0;
    
    // enable the signal level translator to start
    // modem reset process (modem will be powered down)
    shield_3v3_1v8_sig_trans_ena = 1;
    
    // Give the modem 60 secons to start responding by
    // sending simple 'AT' commands to modem once per second.
    Timer timer;
    timer.start();
    while (timer.read() < 60) {
        const char * rsp_lst[] = { ok_str, error_str, NULL };
        int rc = mdm_sendAtCmd("AT", rsp_lst, 500);
        if (rc == 0)
            return timer.read();
        wait_ms(1000 - (timer.read_ms() % 1000));
        pc.printf("\r%d",timer.read_ms()/1000);
    }
    return false;       
}

int mdm_sendAtCmdRsp(const char *cmd, const char **rsp_list, int timeout_ms, string * rsp, int * len) {
    static char cmd_buf[3200];  // Need enough room for the WNC sockreads (over 3000 chars)
    size_t n = strlen(cmd);
    if (cmd && n > 0) {
        if (mdm_dbgmask & MDM_DBG_AT_CMDS) {
            printf(MAG "ATCMD: " DEF "--> " GRN "%s" DEF "\n", cmd);
        }
        while (n--) {
            mdm.putc(*cmd++);
            wait_ms(1);
        };
        mdm.putc('\r');
        wait_ms(1);
        mdm.putc('\n');
        wait_ms(1);
    }

    if (rsp_list) {
        rsp->erase(); // Clean up from prior cmd response
        *len = 0;
        Timer   timer;
        timer.start();
        while (timer.read_ms() < timeout_ms) {
            int lenCmd = mdm_getline(cmd_buf, sizeof(cmd_buf), timeout_ms - timer.read_ms());

            if (lenCmd == 0)
                continue;

            if (lenCmd < 0)
                return MDM_ERR_TIMEOUT;
            else {
                *len += lenCmd;
                *rsp += cmd_buf;
            }

            if (mdm_dbgmask & MDM_DBG_AT_CMDS) {
                printf(MAG "ATRSP: " DEF "<-- " CYN "%s" DEF "\n", cmd_buf);
            }

            int rsp_idx = 0;
            while (rsp_list[rsp_idx]) {
                if (strcasecmp(cmd_buf, rsp_list[rsp_idx]) == 0) {
                    return rsp_idx;
                }
                rsp_idx++;
            }
        }
        return MDM_ERR_TIMEOUT;
    }
    pc.printf("D %s",rsp);
    return MDM_OK;
}

void reinitialize_mdm(void)
{
    // Initialize the modem
    printf(GRN "Modem RE-initializing..." DEF "\r\n");
    if (!mdm_init()) {
        printf(RED "\n\rModem RE-initialization failed!" DEF "\n");
    }
    printf("\r\n");
}
// These are built on the fly
string MyServerIpAddress;
string MySocketData;

// These are to be built on the fly
string my_temp;
string my_humidity;

#define CTOF(x)  ((x)*1.8+32)

#include "Flow_parameters.h"
//********************************************************************************************************************************************
//* Create string that can be sent to flow as an HTTP get
//********************************************************************************************************************************************
static Flow_datapoint_t  FLOW_DATAPOINT =
{
    .URL_start     = FLOW_CALLBACK_URL_START,
    .URL_end       = FLOW_CALLBACK_URL_END
};
void GenerateModemString(char * modem_string)
{
    //sprintf(modem_string, "%s?deviceID=%s&temp=%s&humidity=%s %s", FLOW_DATAPOINT.URL_start, FLOW_DATAPOINT.Device_ID, SENSOR_DATA.Temperature, SENSOR_DATA.Humidity, FLOW_DATAPOINT.URL_end);
    sprintf(modem_string, "%s?serial=vstarterkit001&temp=%s&humidity=%s %s", FLOW_DATAPOINT.URL_start, SENSOR_DATA.Temperature, SENSOR_DATA.Humidity, FLOW_DATAPOINT.URL_end);
} //GenerateModemString        
            
            
//Periodic timer
Ticker OneMsTicker;
volatile bool bTimerExpiredFlag = false;
int OneMsTicks = 0;
int iTimer1Interval_ms = 1000;
//********************************************************************************************************************************************
//* Periodic 1ms timer tick
//********************************************************************************************************************************************
void OneMsFunction() 
{
    OneMsTicks++;
    if ((OneMsTicks % iTimer1Interval_ms) == 0)
    {
        bTimerExpiredFlag = true;
    }            
} //OneMsFunction()

int main() {
    int i;
    HTS221 hts221;
    pc.baud(115200);
    
    void hts221_init(void);

    pc.printf(BLU "Hello World from AT&T Shape!\r\n\n\r");
    pc.printf(GRN "Initialize the HTS221\n\r");

    i = hts221.begin();  
    if( i ) 
        pc.printf(BLU "HTS221 Detected! (0x%02X)\n\r",i);
    else
        pc.printf(RED "HTS221 NOT DETECTED!!\n\r");

    printf("Temp  is: %0.2f F \n\r",CTOF(hts221.readTemperature()));
    printf("Humid is: %02d %%\n\r",hts221.readHumidity());
    
    // Initialize the modem
    printf(GRN "Modem initializing... will take up to 60 seconds" DEF "\r\n");
    i=mdm_init();
    if (!i) {
        pc.printf(RED "Modem initialization failed!" DEF "\n");
        while (1);
    }
    
    //Software init
    software_init_mdm();
    
    // Resolve URL to IP address to connect to
    resolve_mdm();

    sensors_init();
    //Create a 1ms timer tick function:
    OneMsTicker.attach(OneMsFunction, 0.001f) ;
    iTimer1Interval_ms = 5000; //5 seconds

    // Send and receive data perpetually
    while(1) {
        if  (bTimerExpiredFlag)
        {
            bTimerExpiredFlag = false;
            sprintf(SENSOR_DATA.Temperature, "%0.2f", CTOF(hts221.readTemperature()));
            sprintf(SENSOR_DATA.Humidity, "%02d", hts221.readHumidity());
            read_sensors(); //read available external sensors from a PMOD and the on-board motion sensor
            sockopen_mdm();
            char modem_string[512];
            GenerateModemString(&modem_string[0]);
            printf(DEF "Sending to modem : %s\n", modem_string); 
            //sockwrite_mdm("GET \r\n/f653d97537235/a31c2684a02c/d35e42196968fd6/in/flow/climate?deviceID=foo&temp=41.0&humidity=87.33\r\n HTTP/1.1\r\nHost: run-east.att.io:80\r\nAccept: */*\r\n\r\n");
            sockwrite_mdm(modem_string);
            sockread_mdm(&MySocketData, 1024, 20);
            sockclose_mdm();
        } //bTimerExpiredFlag
    } //forever loop

    string * pStr;
    while (1)
    {
       send_wnc_cmd("AT", &pStr, WNC_TIMEOUT_MS);
    }
}