David Rimer
Port of RadioHead version 1.48 to mbed. It is a little messy and only works for SPI at this time.
Diff: radio_config_Si4460.h
- Revision:
- 0:ab4e012489ef
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/radio_config_Si4460.h Thu Oct 15 01:27:00 2015 +0000
@@ -0,0 +1,606 @@
+/*! @file radio_config.h
+ * @brief This file contains the automatically generated
+ * configurations.
+ *
+ * @n WDS GUI Version: 3.2.6.0
+ * @n Device: Si4460 Rev.: B1
+ *
+ * @b COPYRIGHT
+ * @n Silicon Laboratories Confidential
+ * @n Copyright 2013 Silicon Laboratories, Inc.
+ * @n http://www.silabs.com
+ */
+
+#ifndef RADIO_CONFIG_H_
+#define RADIO_CONFIG_H_
+
+// USER DEFINED PARAMETERS
+// Define your own parameters here
+
+// INPUT DATA
+/*
+// Crys_freq(Hz): 30000000 Crys_tol(ppm): 20 IF_mode: 2 High_perf_Ch_Fil: 1 OSRtune: 0 Ch_Fil_Bw_AFC: 0 ANT_DIV: 0 PM_pattern: 0
+// MOD_type: 3 Rsymb(sps): 50000 Fdev(Hz): 100000 RXBW(Hz): 150000 Manchester: 0 AFC_en: 0 Rsymb_error: 0.0 Chip-Version: 2
+// RF Freq.(MHz): 434 API_TC: 31 fhst: 250000 inputBW: 0 BERT: 0 RAW_dout: 0 D_source: 0 Hi_pfm_div: 1
+//
+// # WB filter 2 (BW = 274.83 kHz); NB-filter 2 (BW = 274.83 kHz)
+//
+// Modulation index: 4
+*/
+
+
+// CONFIGURATION PARAMETERS
+#define RADIO_CONFIGURATION_DATA_RADIO_XO_FREQ {30000000L}
+#define RADIO_CONFIGURATION_DATA_CHANNEL_NUMBER {0x00}
+#define RADIO_CONFIGURATION_DATA_RADIO_PACKET_LENGTH {0x07}
+#define RADIO_CONFIGURATION_DATA_RADIO_STATE_AFTER_POWER_UP {0x03}
+#define RADIO_CONFIGURATION_DATA_RADIO_DELAY_CNT_AFTER_RESET {0xF000}
+#define RADIO_CONFIGURATION_DATA_CUSTOM_PAYLOAD {0xC5, 0xC5, 0xC5, 0xC5, 0xC5, 0xC5, 0xC5}
+
+
+// CONFIGURATION COMMANDS
+
+/*
+// Command: RF_POWER_UP
+// Description: Command to power-up the device and select the operational mode and functionality.
+*/
+#define RF_POWER_UP 0x02, 0x01, 0x00, 0x01, 0xC9, 0xC3, 0x80
+
+/*
+// Command: RF_GPIO_PIN_CFG
+// Description: Configures the GPIO pins.
+*/
+#define RF_GPIO_PIN_CFG 0x13, 0x04, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
+
+/*
+// Set properties: RF_GLOBAL_XO_TUNE_1
+// Number of properties: 1
+// Group ID: 0x00
+// Start ID: 0x00
+// Default values: 0x40,
+// Descriptions:
+// GLOBAL_XO_TUNE - Configure the internal capacitor frequency tuning bank for the crystal oscillator.
+*/
+#define RF_GLOBAL_XO_TUNE_1 0x11, 0x00, 0x01, 0x00, 0x52
+
+/*
+// Set properties: RF_GLOBAL_CONFIG_1
+// Number of properties: 1
+// Group ID: 0x00
+// Start ID: 0x03
+// Default values: 0x20,
+// Descriptions:
+// GLOBAL_CONFIG - Global configuration settings.
+*/
+#define RF_GLOBAL_CONFIG_1 0x11, 0x00, 0x01, 0x03, 0x60
+
+/*
+// Set properties: RF_INT_CTL_ENABLE_2
+// Number of properties: 2
+// Group ID: 0x01
+// Start ID: 0x00
+// Default values: 0x04, 0x00,
+// Descriptions:
+// INT_CTL_ENABLE - This property provides for global enabling of the three interrupt groups (Chip, Modem and Packet Handler) in order to generate HW interrupts at the NIRQ pin.
+// INT_CTL_PH_ENABLE - Enable individual interrupt sources within the Packet Handler Interrupt Group to generate a HW interrupt on the NIRQ output pin.
+*/
+#define RF_INT_CTL_ENABLE_2 0x11, 0x01, 0x02, 0x00, 0x01, 0x38
+
+/*
+// Set properties: RF_FRR_CTL_A_MODE_4
+// Number of properties: 4
+// Group ID: 0x02
+// Start ID: 0x00
+// Default values: 0x01, 0x02, 0x09, 0x00,
+// Descriptions:
+// FRR_CTL_A_MODE - Fast Response Register A Configuration.
+// FRR_CTL_B_MODE - Fast Response Register B Configuration.
+// FRR_CTL_C_MODE - Fast Response Register C Configuration.
+// FRR_CTL_D_MODE - Fast Response Register D Configuration.
+*/
+#define RF_FRR_CTL_A_MODE_4 0x11, 0x02, 0x04, 0x00, 0x00, 0x00, 0x00, 0x00
+
+/*
+// Set properties: RF_PREAMBLE_TX_LENGTH_9
+// Number of properties: 9
+// Group ID: 0x10
+// Start ID: 0x00
+// Default values: 0x08, 0x14, 0x00, 0x0F, 0x21, 0x00, 0x00, 0x00, 0x00,
+// Descriptions:
+// PREAMBLE_TX_LENGTH - Configure length of TX Preamble.
+// PREAMBLE_CONFIG_STD_1 - Configuration of reception of a packet with a Standard Preamble pattern.
+// PREAMBLE_CONFIG_NSTD - Configuration of transmission/reception of a packet with a Non-Standard Preamble pattern.
+// PREAMBLE_CONFIG_STD_2 - Configuration of timeout periods during reception of a packet with Standard Preamble pattern.
+// PREAMBLE_CONFIG - General configuration bits for the Preamble field.
+// PREAMBLE_PATTERN_31_24 - Configuration of the bit values describing a Non-Standard Preamble pattern.
+// PREAMBLE_PATTERN_23_16 - Configuration of the bit values describing a Non-Standard Preamble pattern.
+// PREAMBLE_PATTERN_15_8 - Configuration of the bit values describing a Non-Standard Preamble pattern.
+// PREAMBLE_PATTERN_7_0 - Configuration of the bit values describing a Non-Standard Preamble pattern.
+*/
+#define RF_PREAMBLE_TX_LENGTH_9 0x11, 0x10, 0x09, 0x00, 0x08, 0x14, 0x00, 0x0F, 0x31, 0x00, 0x00, 0x00, 0x00
+
+/*
+// Set properties: RF_SYNC_CONFIG_5
+// Number of properties: 5
+// Group ID: 0x11
+// Start ID: 0x00
+// Default values: 0x01, 0x2D, 0xD4, 0x2D, 0xD4,
+// Descriptions:
+// SYNC_CONFIG - Sync Word configuration bits.
+// SYNC_BITS_31_24 - Sync word.
+// SYNC_BITS_23_16 - Sync word.
+// SYNC_BITS_15_8 - Sync word.
+// SYNC_BITS_7_0 - Sync word.
+*/
+#define RF_SYNC_CONFIG_5 0x11, 0x11, 0x05, 0x00, 0x01, 0xB4, 0x2B, 0x00, 0x00
+
+/*
+// Set properties: RF_PKT_CRC_CONFIG_1
+// Number of properties: 1
+// Group ID: 0x12
+// Start ID: 0x00
+// Default values: 0x00,
+// Descriptions:
+// PKT_CRC_CONFIG - Select a CRC polynomial and seed.
+*/
+#define RF_PKT_CRC_CONFIG_1 0x11, 0x12, 0x01, 0x00, 0x80
+
+/*
+// Set properties: RF_PKT_WHT_SEED_15_8_4
+// Number of properties: 4
+// Group ID: 0x12
+// Start ID: 0x03
+// Default values: 0xFF, 0xFF, 0x00, 0x00,
+// Descriptions:
+// PKT_WHT_SEED_15_8 - 16-bit seed value for the PN Generator (e.g., for Data Whitening)
+// PKT_WHT_SEED_7_0 - 16-bit seed value for the PN Generator (e.g., for Data Whitening)
+// PKT_WHT_BIT_NUM - Selects which bit of the LFSR (used to generate the PN / data whitening sequence) is used as the output bit for data scrambling.
+// PKT_CONFIG1 - General configuration bits for transmission or reception of a packet.
+*/
+#define RF_PKT_WHT_SEED_15_8_4 0x11, 0x12, 0x04, 0x03, 0xFF, 0xFF, 0x00, 0x02
+
+/*
+// Set properties: RF_PKT_LEN_12
+// Number of properties: 12
+// Group ID: 0x12
+// Start ID: 0x08
+// Default values: 0x00, 0x00, 0x00, 0x30, 0x30, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+// Descriptions:
+// PKT_LEN - Configuration bits for reception of a variable length packet.
+// PKT_LEN_FIELD_SOURCE - Field number containing the received packet length byte(s).
+// PKT_LEN_ADJUST - Provides for adjustment/offset of the received packet length value (in order to accommodate a variety of methods of defining total packet length).
+// PKT_TX_THRESHOLD - TX FIFO almost empty threshold.
+// PKT_RX_THRESHOLD - RX FIFO Almost Full threshold.
+// PKT_FIELD_1_LENGTH_12_8 - Unsigned 13-bit Field 1 length value.
+// PKT_FIELD_1_LENGTH_7_0 - Unsigned 13-bit Field 1 length value.
+// PKT_FIELD_1_CONFIG - General data processing and packet configuration bits for Field 1.
+// PKT_FIELD_1_CRC_CONFIG - Configuration of CRC control bits across Field 1.
+// PKT_FIELD_2_LENGTH_12_8 - Unsigned 13-bit Field 2 length value.
+// PKT_FIELD_2_LENGTH_7_0 - Unsigned 13-bit Field 2 length value.
+// PKT_FIELD_2_CONFIG - General data processing and packet configuration bits for Field 2.
+*/
+#define RF_PKT_LEN_12 0x11, 0x12, 0x0C, 0x08, 0x00, 0x00, 0x00, 0x30, 0x30, 0x00, 0x07, 0x04, 0x00, 0x00, 0x00, 0x00
+
+/*
+// Set properties: RF_PKT_FIELD_2_CRC_CONFIG_12
+// Number of properties: 12
+// Group ID: 0x12
+// Start ID: 0x14
+// Default values: 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+// Descriptions:
+// PKT_FIELD_2_CRC_CONFIG - Configuration of CRC control bits across Field 2.
+// PKT_FIELD_3_LENGTH_12_8 - Unsigned 13-bit Field 3 length value.
+// PKT_FIELD_3_LENGTH_7_0 - Unsigned 13-bit Field 3 length value.
+// PKT_FIELD_3_CONFIG - General data processing and packet configuration bits for Field 3.
+// PKT_FIELD_3_CRC_CONFIG - Configuration of CRC control bits across Field 3.
+// PKT_FIELD_4_LENGTH_12_8 - Unsigned 13-bit Field 4 length value.
+// PKT_FIELD_4_LENGTH_7_0 - Unsigned 13-bit Field 4 length value.
+// PKT_FIELD_4_CONFIG - General data processing and packet configuration bits for Field 4.
+// PKT_FIELD_4_CRC_CONFIG - Configuration of CRC control bits across Field 4.
+// PKT_FIELD_5_LENGTH_12_8 - Unsigned 13-bit Field 5 length value.
+// PKT_FIELD_5_LENGTH_7_0 - Unsigned 13-bit Field 5 length value.
+// PKT_FIELD_5_CONFIG - General data processing and packet configuration bits for Field 5.
+*/
+#define RF_PKT_FIELD_2_CRC_CONFIG_12 0x11, 0x12, 0x0C, 0x14, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
+
+/*
+// Set properties: RF_PKT_FIELD_5_CRC_CONFIG_1
+// Number of properties: 1
+// Group ID: 0x12
+// Start ID: 0x20
+// Default values: 0x00,
+// Descriptions:
+// PKT_FIELD_5_CRC_CONFIG - Configuration of CRC control bits across Field 5.
+*/
+#define RF_PKT_FIELD_5_CRC_CONFIG_1 0x11, 0x12, 0x01, 0x20, 0x00
+
+/*
+// Set properties: RF_MODEM_MOD_TYPE_12
+// Number of properties: 12
+// Group ID: 0x20
+// Start ID: 0x00
+// Default values: 0x02, 0x80, 0x07, 0x0F, 0x42, 0x40, 0x01, 0xC9, 0xC3, 0x80, 0x00, 0x06,
+// Descriptions:
+// MODEM_MOD_TYPE - Selects the type of modulation. In TX mode, additionally selects the source of the modulation.
+// MODEM_MAP_CONTROL - Controls polarity and mapping of transmit and receive bits.
+// MODEM_DSM_CTRL - Miscellaneous control bits for the Delta-Sigma Modulator (DSM) in the PLL Synthesizer.
+// MODEM_DATA_RATE_2 - Unsigned 24-bit value used to determine the TX data rate
+// MODEM_DATA_RATE_1 - Unsigned 24-bit value used to determine the TX data rate
+// MODEM_DATA_RATE_0 - Unsigned 24-bit value used to determine the TX data rate
+// MODEM_TX_NCO_MODE_3 - TX Gaussian filter oversampling ratio and Byte 3 of unsigned 26-bit TX Numerically Controlled Oscillator (NCO) modulus.
+// MODEM_TX_NCO_MODE_2 - TX Gaussian filter oversampling ratio and Byte 3 of unsigned 26-bit TX Numerically Controlled Oscillator (NCO) modulus.
+// MODEM_TX_NCO_MODE_1 - TX Gaussian filter oversampling ratio and Byte 3 of unsigned 26-bit TX Numerically Controlled Oscillator (NCO) modulus.
+// MODEM_TX_NCO_MODE_0 - TX Gaussian filter oversampling ratio and Byte 3 of unsigned 26-bit TX Numerically Controlled Oscillator (NCO) modulus.
+// MODEM_FREQ_DEV_2 - 17-bit unsigned TX frequency deviation word.
+// MODEM_FREQ_DEV_1 - 17-bit unsigned TX frequency deviation word.
+*/
+#define RF_MODEM_MOD_TYPE_12 0x11, 0x20, 0x0C, 0x00, 0x03, 0x00, 0x07, 0x0F, 0x42, 0x40, 0x09, 0xC9, 0xC3, 0x80, 0x00, 0x1B
+
+/*
+// Set properties: RF_MODEM_FREQ_DEV_0_1
+// Number of properties: 1
+// Group ID: 0x20
+// Start ID: 0x0C
+// Default values: 0xD3,
+// Descriptions:
+// MODEM_FREQ_DEV_0 - 17-bit unsigned TX frequency deviation word.
+*/
+#define RF_MODEM_FREQ_DEV_0_1 0x11, 0x20, 0x01, 0x0C, 0x4F
+
+/*
+// Set properties: RF_MODEM_TX_RAMP_DELAY_8
+// Number of properties: 8
+// Group ID: 0x20
+// Start ID: 0x18
+// Default values: 0x01, 0x00, 0x08, 0x03, 0xC0, 0x00, 0x10, 0x20,
+// Descriptions:
+// MODEM_TX_RAMP_DELAY - TX ramp-down delay setting.
+// MODEM_MDM_CTRL - MDM control.
+// MODEM_IF_CONTROL - Selects Fixed-IF, Scaled-IF, or Zero-IF mode of RX Modem operation.
+// MODEM_IF_FREQ_2 - the IF frequency setting (an 18-bit signed number).
+// MODEM_IF_FREQ_1 - the IF frequency setting (an 18-bit signed number).
+// MODEM_IF_FREQ_0 - the IF frequency setting (an 18-bit signed number).
+// MODEM_DECIMATION_CFG1 - Specifies three decimator ratios for the Cascaded Integrator Comb (CIC) filter.
+// MODEM_DECIMATION_CFG0 - Specifies miscellaneous parameters and decimator ratios for the Cascaded Integrator Comb (CIC) filter.
+*/
+#define RF_MODEM_TX_RAMP_DELAY_8 0x11, 0x20, 0x08, 0x18, 0x01, 0x80, 0x08, 0x03, 0x80, 0x00, 0x00, 0x10
+
+/*
+// Set properties: RF_MODEM_BCR_OSR_1_9
+// Number of properties: 9
+// Group ID: 0x20
+// Start ID: 0x22
+// Default values: 0x00, 0x4B, 0x06, 0xD3, 0xA0, 0x06, 0xD3, 0x02, 0xC0,
+// Descriptions:
+// MODEM_BCR_OSR_1 - RX BCR/Slicer oversampling rate (12-bit unsigned number).
+// MODEM_BCR_OSR_0 - RX BCR/Slicer oversampling rate (12-bit unsigned number).
+// MODEM_BCR_NCO_OFFSET_2 - RX BCR NCO offset value (an unsigned 22-bit number).
+// MODEM_BCR_NCO_OFFSET_1 - RX BCR NCO offset value (an unsigned 22-bit number).
+// MODEM_BCR_NCO_OFFSET_0 - RX BCR NCO offset value (an unsigned 22-bit number).
+// MODEM_BCR_GAIN_1 - The unsigned 11-bit RX BCR loop gain value.
+// MODEM_BCR_GAIN_0 - The unsigned 11-bit RX BCR loop gain value.
+// MODEM_BCR_GEAR - RX BCR loop gear control.
+// MODEM_BCR_MISC1 - Miscellaneous control bits for the RX BCR loop.
+*/
+#define RF_MODEM_BCR_OSR_1_9 0x11, 0x20, 0x09, 0x22, 0x00, 0xC8, 0x02, 0x8F, 0x5C, 0x01, 0x48, 0x02, 0xC2
+
+/*
+// Set properties: RF_MODEM_AFC_GEAR_7
+// Number of properties: 7
+// Group ID: 0x20
+// Start ID: 0x2C
+// Default values: 0x00, 0x23, 0x83, 0x69, 0x00, 0x40, 0xA0,
+// Descriptions:
+// MODEM_AFC_GEAR - RX AFC loop gear control.
+// MODEM_AFC_WAIT - RX AFC loop wait time control.
+// MODEM_AFC_GAIN_1 - Sets the gain of the PLL-based AFC acquisition loop, and provides miscellaneous control bits for AFC functionality.
+// MODEM_AFC_GAIN_0 - Sets the gain of the PLL-based AFC acquisition loop, and provides miscellaneous control bits for AFC functionality.
+// MODEM_AFC_LIMITER_1 - Set the AFC limiter value.
+// MODEM_AFC_LIMITER_0 - Set the AFC limiter value.
+// MODEM_AFC_MISC - Specifies miscellaneous AFC control bits.
+*/
+#define RF_MODEM_AFC_GEAR_7 0x11, 0x20, 0x07, 0x2C, 0x04, 0x36, 0x80, 0x92, 0x0A, 0x46, 0x80
+
+/*
+// Set properties: RF_MODEM_AGC_CONTROL_1
+// Number of properties: 1
+// Group ID: 0x20
+// Start ID: 0x35
+// Default values: 0xE0,
+// Descriptions:
+// MODEM_AGC_CONTROL - Miscellaneous control bits for the Automatic Gain Control (AGC) function in the RX Chain.
+*/
+#define RF_MODEM_AGC_CONTROL_1 0x11, 0x20, 0x01, 0x35, 0xE2
+
+/*
+// Set properties: RF_MODEM_AGC_WINDOW_SIZE_9
+// Number of properties: 9
+// Group ID: 0x20
+// Start ID: 0x38
+// Default values: 0x11, 0x10, 0x10, 0x0B, 0x1C, 0x40, 0x00, 0x00, 0x2B,
+// Descriptions:
+// MODEM_AGC_WINDOW_SIZE - Specifies the size of the measurement and settling windows for the AGC algorithm.
+// MODEM_AGC_RFPD_DECAY - Sets the decay time of the RF peak detectors.
+// MODEM_AGC_IFPD_DECAY - Sets the decay time of the IF peak detectors.
+// MODEM_FSK4_GAIN1 - Specifies the gain factor of the secondary branch in 4(G)FSK ISI-suppression.
+// MODEM_FSK4_GAIN0 - Specifies the gain factor of the primary branch in 4(G)FSK ISI-suppression.
+// MODEM_FSK4_TH1 - 16 bit 4(G)FSK slicer threshold.
+// MODEM_FSK4_TH0 - 16 bit 4(G)FSK slicer threshold.
+// MODEM_FSK4_MAP - 4(G)FSK symbol mapping code.
+// MODEM_OOK_PDTC - Configures the attack and decay times of the OOK Peak Detector.
+*/
+#define RF_MODEM_AGC_WINDOW_SIZE_9 0x11, 0x20, 0x09, 0x38, 0x11, 0x2C, 0x2C, 0x00, 0x1A, 0xFF, 0xFF, 0x00, 0x29
+
+/*
+// Set properties: RF_MODEM_OOK_CNT1_11
+// Number of properties: 11
+// Group ID: 0x20
+// Start ID: 0x42
+// Default values: 0xA4, 0x03, 0x56, 0x02, 0x00, 0xA3, 0x02, 0x80, 0xFF, 0x0C, 0x01,
+// Descriptions:
+// MODEM_OOK_CNT1 - OOK control.
+// MODEM_OOK_MISC - Selects the detector(s) used for demodulation of an OOK signal, or for demodulation of a (G)FSK signal when using the asynchronous demodulator.
+// MODEM_RAW_SEARCH - Defines and controls the search period length for the Moving Average and Min-Max detectors.
+// MODEM_RAW_CONTROL - Defines gain and enable controls for raw / nonstandard mode.
+// MODEM_RAW_EYE_1 - 11 bit eye-open detector threshold.
+// MODEM_RAW_EYE_0 - 11 bit eye-open detector threshold.
+// MODEM_ANT_DIV_MODE - Antenna diversity mode settings.
+// MODEM_ANT_DIV_CONTROL - Specifies controls for the Antenna Diversity algorithm.
+// MODEM_RSSI_THRESH - Configures the RSSI threshold.
+// MODEM_RSSI_JUMP_THRESH - Configures the RSSI Jump Detection threshold.
+// MODEM_RSSI_CONTROL - Control of the averaging modes and latching time for reporting RSSI value(s).
+*/
+#define RF_MODEM_OOK_CNT1_11 0x11, 0x20, 0x0B, 0x42, 0xA4, 0x02, 0xD6, 0x83, 0x01, 0x7F, 0x01, 0x80, 0xFF, 0x0C, 0x02
+
+/*
+// Set properties: RF_MODEM_RSSI_COMP_1
+// Number of properties: 1
+// Group ID: 0x20
+// Start ID: 0x4E
+// Default values: 0x40,
+// Descriptions:
+// MODEM_RSSI_COMP - RSSI compensation value.
+*/
+#define RF_MODEM_RSSI_COMP_1 0x11, 0x20, 0x01, 0x4E, 0x40
+
+/*
+// Set properties: RF_MODEM_CLKGEN_BAND_1
+// Number of properties: 1
+// Group ID: 0x20
+// Start ID: 0x51
+// Default values: 0x08,
+// Descriptions:
+// MODEM_CLKGEN_BAND - Select PLL Synthesizer output divider ratio as a function of frequency band.
+*/
+#define RF_MODEM_CLKGEN_BAND_1 0x11, 0x20, 0x01, 0x51, 0x0A
+
+/*
+// Set properties: RF_MODEM_CHFLT_RX1_CHFLT_COE13_7_0_12
+// Number of properties: 12
+// Group ID: 0x21
+// Start ID: 0x00
+// Default values: 0xFF, 0xBA, 0x0F, 0x51, 0xCF, 0xA9, 0xC9, 0xFC, 0x1B, 0x1E, 0x0F, 0x01,
+// Descriptions:
+// MODEM_CHFLT_RX1_CHFLT_COE13_7_0 - Filter coefficients for the first set of RX filter coefficients.
+// MODEM_CHFLT_RX1_CHFLT_COE12_7_0 - Filter coefficients for the first set of RX filter coefficients.
+// MODEM_CHFLT_RX1_CHFLT_COE11_7_0 - Filter coefficients for the first set of RX filter coefficients.
+// MODEM_CHFLT_RX1_CHFLT_COE10_7_0 - Filter coefficients for the first set of RX filter coefficients.
+// MODEM_CHFLT_RX1_CHFLT_COE9_7_0 - Filter coefficients for the first set of RX filter coefficients.
+// MODEM_CHFLT_RX1_CHFLT_COE8_7_0 - Filter coefficients for the first set of RX filter coefficients.
+// MODEM_CHFLT_RX1_CHFLT_COE7_7_0 - Filter coefficients for the first set of RX filter coefficients.
+// MODEM_CHFLT_RX1_CHFLT_COE6_7_0 - Filter coefficients for the first set of RX filter coefficients.
+// MODEM_CHFLT_RX1_CHFLT_COE5_7_0 - Filter coefficients for the first set of RX filter coefficients.
+// MODEM_CHFLT_RX1_CHFLT_COE4_7_0 - Filter coefficients for the first set of RX filter coefficients.
+// MODEM_CHFLT_RX1_CHFLT_COE3_7_0 - Filter coefficients for the first set of RX filter coefficients.
+// MODEM_CHFLT_RX1_CHFLT_COE2_7_0 - Filter coefficients for the first set of RX filter coefficients.
+*/
+#define RF_MODEM_CHFLT_RX1_CHFLT_COE13_7_0_12 0x11, 0x21, 0x0C, 0x00, 0xFF, 0xC4, 0x30, 0x7F, 0xF5, 0xB5, 0xB8, 0xDE, 0x05, 0x17, 0x16, 0x0C
+
+/*
+// Set properties: RF_MODEM_CHFLT_RX1_CHFLT_COE1_7_0_12
+// Number of properties: 12
+// Group ID: 0x21
+// Start ID: 0x0C
+// Default values: 0xFC, 0xFD, 0x15, 0xFF, 0x00, 0x0F, 0xFF, 0xC4, 0x30, 0x7F, 0xF5, 0xB5,
+// Descriptions:
+// MODEM_CHFLT_RX1_CHFLT_COE1_7_0 - Filter coefficients for the first set of RX filter coefficients.
+// MODEM_CHFLT_RX1_CHFLT_COE0_7_0 - Filter coefficients for the first set of RX filter coefficients.
+// MODEM_CHFLT_RX1_CHFLT_COEM0 - Filter coefficients for the first set of RX filter coefficients.
+// MODEM_CHFLT_RX1_CHFLT_COEM1 - Filter coefficients for the first set of RX filter coefficients.
+// MODEM_CHFLT_RX1_CHFLT_COEM2 - Filter coefficients for the first set of RX filter coefficients.
+// MODEM_CHFLT_RX1_CHFLT_COEM3 - Filter coefficients for the first set of RX filter coefficients.
+// MODEM_CHFLT_RX2_CHFLT_COE13_7_0 - Filter coefficients for the second set of RX filter coefficients.
+// MODEM_CHFLT_RX2_CHFLT_COE12_7_0 - Filter coefficients for the second set of RX filter coefficients.
+// MODEM_CHFLT_RX2_CHFLT_COE11_7_0 - Filter coefficients for the second set of RX filter coefficients.
+// MODEM_CHFLT_RX2_CHFLT_COE10_7_0 - Filter coefficients for the second set of RX filter coefficients.
+// MODEM_CHFLT_RX2_CHFLT_COE9_7_0 - Filter coefficients for the second set of RX filter coefficients.
+// MODEM_CHFLT_RX2_CHFLT_COE8_7_0 - Filter coefficients for the second set of RX filter coefficients.
+*/
+#define RF_MODEM_CHFLT_RX1_CHFLT_COE1_7_0_12 0x11, 0x21, 0x0C, 0x0C, 0x03, 0x00, 0x15, 0xFF, 0x00, 0x00, 0xFF, 0xC4, 0x30, 0x7F, 0xF5, 0xB5
+
+/*
+// Set properties: RF_MODEM_CHFLT_RX2_CHFLT_COE7_7_0_12
+// Number of properties: 12
+// Group ID: 0x21
+// Start ID: 0x18
+// Default values: 0xB8, 0xDE, 0x05, 0x17, 0x16, 0x0C, 0x03, 0x00, 0x15, 0xFF, 0x00, 0x00,
+// Descriptions:
+// MODEM_CHFLT_RX2_CHFLT_COE7_7_0 - Filter coefficients for the second set of RX filter coefficients.
+// MODEM_CHFLT_RX2_CHFLT_COE6_7_0 - Filter coefficients for the second set of RX filter coefficients.
+// MODEM_CHFLT_RX2_CHFLT_COE5_7_0 - Filter coefficients for the second set of RX filter coefficients.
+// MODEM_CHFLT_RX2_CHFLT_COE4_7_0 - Filter coefficients for the second set of RX filter coefficients.
+// MODEM_CHFLT_RX2_CHFLT_COE3_7_0 - Filter coefficients for the second set of RX filter coefficients.
+// MODEM_CHFLT_RX2_CHFLT_COE2_7_0 - Filter coefficients for the second set of RX filter coefficients.
+// MODEM_CHFLT_RX2_CHFLT_COE1_7_0 - Filter coefficients for the second set of RX filter coefficients.
+// MODEM_CHFLT_RX2_CHFLT_COE0_7_0 - Filter coefficients for the second set of RX filter coefficients.
+// MODEM_CHFLT_RX2_CHFLT_COEM0 - Filter coefficients for the second set of RX filter coefficients.
+// MODEM_CHFLT_RX2_CHFLT_COEM1 - Filter coefficients for the second set of RX filter coefficients.
+// MODEM_CHFLT_RX2_CHFLT_COEM2 - Filter coefficients for the second set of RX filter coefficients.
+// MODEM_CHFLT_RX2_CHFLT_COEM3 - Filter coefficients for the second set of RX filter coefficients.
+*/
+#define RF_MODEM_CHFLT_RX2_CHFLT_COE7_7_0_12 0x11, 0x21, 0x0C, 0x18, 0xB8, 0xDE, 0x05, 0x17, 0x16, 0x0C, 0x03, 0x00, 0x15, 0xFF, 0x00, 0x00
+
+/*
+// Set properties: RF_PA_MODE_4
+// Number of properties: 4
+// Group ID: 0x22
+// Start ID: 0x00
+// Default values: 0x08, 0x7F, 0x00, 0x5D,
+// Descriptions:
+// PA_MODE - Selects the PA operating mode, and selects resolution of PA power adjustment (i.e., step size).
+// PA_PWR_LVL - Configuration of PA output power level.
+// PA_BIAS_CLKDUTY - Configuration of the PA Bias and duty cycle of the TX clock source.
+// PA_TC - Configuration of PA ramping parameters.
+*/
+#define RF_PA_MODE_4 0x11, 0x22, 0x04, 0x00, 0x18, 0x01, 0xC0, 0x3F
+
+/*
+// Set properties: RF_SYNTH_PFDCP_CPFF_7
+// Number of properties: 7
+// Group ID: 0x23
+// Start ID: 0x00
+// Default values: 0x2C, 0x0E, 0x0B, 0x04, 0x0C, 0x73, 0x03,
+// Descriptions:
+// SYNTH_PFDCP_CPFF - Feed forward charge pump current selection.
+// SYNTH_PFDCP_CPINT - Integration charge pump current selection.
+// SYNTH_VCO_KV - Gain scaling factors (Kv) for the VCO tuning varactors on both the integrated-path and feed forward path.
+// SYNTH_LPFILT3 - Value of resistor R2 in feed-forward path of loop filter.
+// SYNTH_LPFILT2 - Value of capacitor C2 in feed-forward path of loop filter.
+// SYNTH_LPFILT1 - Value of capacitors C1 and C3 in feed-forward path of loop filter.
+// SYNTH_LPFILT0 - Bias current of the active amplifier in the feed-forward loop filter.
+*/
+#define RF_SYNTH_PFDCP_CPFF_7 0x11, 0x23, 0x07, 0x00, 0x2C, 0x0E, 0x0B, 0x04, 0x0C, 0x73, 0x03
+
+/*
+// Set properties: RF_MATCH_VALUE_1_12
+// Number of properties: 12
+// Group ID: 0x30
+// Start ID: 0x00
+// Default values: 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+// Descriptions:
+// MATCH_VALUE_1 - Match value to be compared with the result of logically AND-ing (bit-wise) the Mask 1 value with the received Match 1 byte.
+// MATCH_MASK_1 - Mask value to be logically AND-ed (bit-wise) with the Match 1 byte.
+// MATCH_CTRL_1 - Enable for Packet Match functionality, and configuration of Match Byte 1.
+// MATCH_VALUE_2 - Match value to be compared with the result of logically AND-ing (bit-wise) the Mask 2 value with the received Match 2 byte.
+// MATCH_MASK_2 - Mask value to be logically AND-ed (bit-wise) with the Match 2 byte.
+// MATCH_CTRL_2 - Configuration of Match Byte 2.
+// MATCH_VALUE_3 - Match value to be compared with the result of logically AND-ing (bit-wise) the Mask 3 value with the received Match 3 byte.
+// MATCH_MASK_3 - Mask value to be logically AND-ed (bit-wise) with the Match 3 byte.
+// MATCH_CTRL_3 - Configuration of Match Byte 3.
+// MATCH_VALUE_4 - Match value to be compared with the result of logically AND-ing (bit-wise) the Mask 4 value with the received Match 4 byte.
+// MATCH_MASK_4 - Mask value to be logically AND-ed (bit-wise) with the Match 4 byte.
+// MATCH_CTRL_4 - Configuration of Match Byte 4.
+*/
+#define RF_MATCH_VALUE_1_12 0x11, 0x30, 0x0C, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00
+
+/*
+// Set properties: RF_FREQ_CONTROL_INTE_8
+// Number of properties: 8
+// Group ID: 0x40
+// Start ID: 0x00
+// Default values: 0x3C, 0x08, 0x00, 0x00, 0x00, 0x00, 0x20, 0xFF,
+// Descriptions:
+// FREQ_CONTROL_INTE - Frac-N PLL Synthesizer integer divide number.
+// FREQ_CONTROL_FRAC_2 - Frac-N PLL fraction number.
+// FREQ_CONTROL_FRAC_1 - Frac-N PLL fraction number.
+// FREQ_CONTROL_FRAC_0 - Frac-N PLL fraction number.
+// FREQ_CONTROL_CHANNEL_STEP_SIZE_1 - EZ Frequency Programming channel step size.
+// FREQ_CONTROL_CHANNEL_STEP_SIZE_0 - EZ Frequency Programming channel step size.
+// FREQ_CONTROL_W_SIZE - Set window gating period (in number of crystal reference clock cycles) for counting VCO frequency during calibration.
+// FREQ_CONTROL_VCOCNT_RX_ADJ - Adjust target count for VCO calibration in RX mode.
+*/
+#define RF_FREQ_CONTROL_INTE_8 0x11, 0x40, 0x08, 0x00, 0x38, 0x0E, 0xEE, 0xEE, 0x44, 0x44, 0x20, 0xFE
+
+
+// AUTOMATICALLY GENERATED CODE!
+// DO NOT EDIT/MODIFY BELOW THIS LINE!
+// --------------------------------------------
+
+#ifndef FIRMWARE_LOAD_COMPILE
+#define RADIO_CONFIGURATION_DATA_ARRAY { \
+ 0x07, RF_POWER_UP, \
+ 0x08, RF_GPIO_PIN_CFG, \
+ 0x05, RF_GLOBAL_XO_TUNE_1, \
+ 0x05, RF_GLOBAL_CONFIG_1, \
+ 0x06, RF_INT_CTL_ENABLE_2, \
+ 0x08, RF_FRR_CTL_A_MODE_4, \
+ 0x0D, RF_PREAMBLE_TX_LENGTH_9, \
+ 0x09, RF_SYNC_CONFIG_5, \
+ 0x05, RF_PKT_CRC_CONFIG_1, \
+ 0x08, RF_PKT_WHT_SEED_15_8_4, \
+ 0x10, RF_PKT_LEN_12, \
+ 0x10, RF_PKT_FIELD_2_CRC_CONFIG_12, \
+ 0x05, RF_PKT_FIELD_5_CRC_CONFIG_1, \
+ 0x10, RF_MODEM_MOD_TYPE_12, \
+ 0x05, RF_MODEM_FREQ_DEV_0_1, \
+ 0x0C, RF_MODEM_TX_RAMP_DELAY_8, \
+ 0x0D, RF_MODEM_BCR_OSR_1_9, \
+ 0x0B, RF_MODEM_AFC_GEAR_7, \
+ 0x05, RF_MODEM_AGC_CONTROL_1, \
+ 0x0D, RF_MODEM_AGC_WINDOW_SIZE_9, \
+ 0x0F, RF_MODEM_OOK_CNT1_11, \
+ 0x05, RF_MODEM_RSSI_COMP_1, \
+ 0x05, RF_MODEM_CLKGEN_BAND_1, \
+ 0x10, RF_MODEM_CHFLT_RX1_CHFLT_COE13_7_0_12, \
+ 0x10, RF_MODEM_CHFLT_RX1_CHFLT_COE1_7_0_12, \
+ 0x10, RF_MODEM_CHFLT_RX2_CHFLT_COE7_7_0_12, \
+ 0x08, RF_PA_MODE_4, \
+ 0x0B, RF_SYNTH_PFDCP_CPFF_7, \
+ 0x10, RF_MATCH_VALUE_1_12, \
+ 0x0C, RF_FREQ_CONTROL_INTE_8, \
+ 0x00 \
+ }
+#else
+#define RADIO_CONFIGURATION_DATA_ARRAY { 0 }
+#endif
+
+// DEFAULT VALUES FOR CONFIGURATION PARAMETERS
+#define RADIO_CONFIGURATION_DATA_RADIO_XO_FREQ_DEFAULT 30000000L
+#define RADIO_CONFIGURATION_DATA_CHANNEL_NUMBER_DEFAULT 0x00
+#define RADIO_CONFIGURATION_DATA_RADIO_PACKET_LENGTH_DEFAULT 0x10
+#define RADIO_CONFIGURATION_DATA_RADIO_STATE_AFTER_POWER_UP_DEFAULT 0x01
+#define RADIO_CONFIGURATION_DATA_RADIO_DELAY_CNT_AFTER_RESET_DEFAULT 0x1000
+#define RADIO_CONFIGURATION_DATA_CUSTOM_PAYLOAD_DEFAULT 0x42, 0x55, 0x54, 0x54, 0x4F, 0x4E, 0x31 // BUTTON1
+
+#define RADIO_CONFIGURATION_DATA_RADIO_PATCH_INCLUDED 0x00
+#define RADIO_CONFIGURATION_DATA_RADIO_PATCH_SIZE 0x00
+#define RADIO_CONFIGURATION_DATA_RADIO_PATCH { }
+
+#ifndef RADIO_CONFIGURATION_DATA_ARRAY
+#error "This property must be defined!"
+#endif
+
+#ifndef RADIO_CONFIGURATION_DATA_RADIO_XO_FREQ
+#define RADIO_CONFIGURATION_DATA_RADIO_XO_FREQ { RADIO_CONFIGURATION_DATA_RADIO_XO_FREQ_DEFAULT }
+#endif
+
+#ifndef RADIO_CONFIGURATION_DATA_CHANNEL_NUMBER
+#define RADIO_CONFIGURATION_DATA_CHANNEL_NUMBER { RADIO_CONFIGURATION_DATA_CHANNEL_NUMBER_DEFAULT }
+#endif
+
+#ifndef RADIO_CONFIGURATION_DATA_RADIO_PACKET_LENGTH
+#define RADIO_CONFIGURATION_DATA_RADIO_PACKET_LENGTH { RADIO_CONFIGURATION_DATA_RADIO_PACKET_LENGTH_DEFAULT }
+#endif
+
+#ifndef RADIO_CONFIGURATION_DATA_RADIO_STATE_AFTER_POWER_UP
+#define RADIO_CONFIGURATION_DATA_RADIO_STATE_AFTER_POWER_UP { RADIO_CONFIGURATION_DATA_RADIO_STATE_AFTER_POWER_UP_DEFAULT }
+#endif
+
+#ifndef RADIO_CONFIGURATION_DATA_RADIO_DELAY_CNT_AFTER_RESET
+#define RADIO_CONFIGURATION_DATA_RADIO_DELAY_CNT_AFTER_RESET { RADIO_CONFIGURATION_DATA_RADIO_DELAY_CNT_AFTER_RESET_DEFAULT }
+#endif
+
+#ifndef RADIO_CONFIGURATION_DATA_CUSTOM_PAYLOAD
+#define RADIO_CONFIGURATION_DATA_CUSTOM_PAYLOAD { RADIO_CONFIGURATION_DATA_CUSTOM_PAYLOAD_DEFAULT }
+#endif
+
+#define RADIO_CONFIGURATION_DATA { \
+ Radio_Configuration_Data_Array, \
+ RADIO_CONFIGURATION_DATA_CHANNEL_NUMBER, \
+ RADIO_CONFIGURATION_DATA_RADIO_PACKET_LENGTH, \
+ RADIO_CONFIGURATION_DATA_RADIO_STATE_AFTER_POWER_UP, \
+ RADIO_CONFIGURATION_DATA_RADIO_DELAY_CNT_AFTER_RESET, \
+ RADIO_CONFIGURATION_DATA_CUSTOM_PAYLOAD \
+ }
+
+#endif /* RADIO_CONFIG_H_ */