demo1
Dependencies: SHT30-DIS-B WakeUp mbed
Fork of M1DK_Skywire_Demo by
main.cpp
- Committer:
- kylerodgers
- Date:
- 2017-10-24
- Revision:
- 13:f827f384f0a1
- Parent:
- 11:78a28ca6409f
- Child:
- 14:44eb72d9995e
File content as of revision 13:f827f384f0a1:
/* main.cpp */ /* Copyright (C) 2017 nimbelink.com, MIT License * * Permission is hereby granted, free of charge, to any person obtaining a copy of this software * and associated documentation files (the "Software"), to deal in the Software without restriction, * including without limitation the rights to use, copy, modify, merge, publish, distribute, * sublicense, and/or sell copies of the Software, and to permit persons to whom the Software is * furnished to do so, subject to the following conditions: * * The above copyright notice and this permission notice shall be included in all copies or * substantial portions of the Software. * * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING * BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, * DAMAGES OR OTHER LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM, * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN THE SOFTWARE. */ /* * DESCRIPTION * This code sends sensor data to Dweet.io on the NL-M1DK. */ /* * INSTRUCTIONS FOR USING THIS CODE * 1. Change the "DeviceID" to a unique identifier for your Nucleo board. One recommendation * would be to use the MEID/IMEI of your Skywire Modem. */ #include "mbed.h" // mbed Library #include "pinmap.h" // pinmap needed for hardware flow control #include "SHT30DISB.h" // --CHANGE THIS FOR YOUR SETUP-- #define DeviceID "<your Thingname here>" //DweetIO unique ID // --CHANGE THIS FOR YOUR SETUP (IF APPLICABLE)-- const char *APN = "NIMBLINK.GW12.VZWENTP"; DigitalOut myled(LED1); // Main LED DigitalOut skywire_rts(PB_5); // Skywire Send DigitalOut green_LED(D7); // Green LED DigitalOut red_LED(D10); // Red LED DigitalOut nRESET(PB_4); // Skywire Reset line AnalogIn photo_trans(A3); // Photo Transistor DigitalOut photo_trans_nEN(D11); // Photo Transistor Enable DigitalIn button1(PA_5); // Button 1 Serial skywire(PA_9,PA_10); // Serial comms to Skywire Serial debug_pc(USBTX, USBRX); // USB connection to PC I2C i2c(PB_9,PB_8); // Setup I2C bus for sensors // SHT30 Sensor Setup SHT30DISB SHT30(i2c); // variable to switch state bool sw1; // char array for reading from Skywire char str[255]; // Variables for checking CSQ char csq[3]="99"; int csq_val = 99; // Variables for UART comms volatile int rx_in=0; volatile int rx_out=0; const int buffer_size = 600; char rx_buffer[buffer_size+1]; char rx_line[buffer_size]; // Interrupt for the Skywire void Skywire_Rx_interrupt() { // Loop just in case more than one character is in UART's receive FIFO buffer // Stop if buffer full while ((skywire.readable()) && (((rx_in + 1) % buffer_size) != rx_out)) { rx_buffer[rx_in] = skywire.getc(); rx_in = (rx_in + 1) % buffer_size; } return; } // Read line from the UART void read_line() { int i; i = 0; // Start Critical Section - don't interrupt while changing global buffer variables __disable_irq(); // Loop reading rx buffer characters until end of line character while ((i==0) || (rx_line[i-1] != '\n')) { // Wait if buffer empty if (rx_in == rx_out) { // End Critical Section - need to allow rx interrupt to get new characters for buffer __enable_irq(); while (rx_in == rx_out) { } // Start Critical Section - don't interrupt while changing global buffer variables __disable_irq(); } rx_line[i] = rx_buffer[rx_out]; i++; rx_out = (rx_out + 1) % buffer_size; } // End Critical Section __enable_irq(); rx_line[i-1] = 0; return; } // Wait for specific response int WaitForResponse(const char *response) { debug_pc.printf("Command sent. Waiting for: %s\r\n", response); do { read_line(); // If we get ERROR, return with 1 if (strncmp(rx_line, "ERROR", strlen("ERROR")) == 0) { debug_pc.printf("ERROR\r\n"); return 1; } debug_pc.printf("Waiting for: %s, Recieved: %s\r\n", response, rx_line); } while (strncmp(rx_line, response, strlen(response))); return 0; } // Send AT+CSQ until we get a good signal int GetCSQResponse() { do { skywire.printf("AT+CSQ\r"); WaitForResponse("OK"); csq[0]=rx_line[6]; csq[1]=rx_line[7]; csq_val=atoi(csq); } while (!strncmp(rx_line, "CSQ: 99,", 8)); return csq_val; } int main() { red_LED = 1; float temp; float humi; float photo; // Setup serial comms with Skywire and PC debug_pc.baud(115200); skywire.baud(921600); skywire_rts = 0; debug_pc.printf("SystemCoreClock = %d Hz\r\n", SystemCoreClock); debug_pc.printf("Attaching interrupt...\r\n"); skywire.attach(&Skywire_Rx_interrupt, Serial::RxIrq); debug_pc.printf("Interrupt attached...\r\n"); // Reset the Skywire to get AT commands, and recover from any previous state debug_pc.printf("Resetting Skywire...\r\n"); nRESET = 1; wait_ms(100); nRESET = 0; wait(3); debug_pc.printf("Resetting baud...\r\n"); skywire.printf("\rAT+IPR=115200\r"); wait_ms(100); skywire.baud(115200); wait_ms(100); debug_pc.printf("Baud reset!\r\n"); myled=0; debug_pc.printf("Starting Demo...\r\n"); debug_pc.printf("Waiting for Skywire to Boot...\r\n"); green_LED = !green_LED; myled=1; wait_ms(100); debug_pc.printf("Sending AT\r\n"); skywire.printf("\rAT\r"); WaitForResponse("OK"); WaitForResponse("+CEREG: 1"); // Check CSQ debug_pc.printf("Getting CSQ...\r\n"); GetCSQResponse(); green_LED = !green_LED; while(csq_val==99 || csq_val==0) { debug_pc.printf("CSQ Value: %i\r\n",csq_val); debug_pc.printf("No network sginal detected. \r\n"); debug_pc.printf("Waiting for device to connect to the network. \r\n"); debug_pc.printf("Please check antenna connections if network is not found after 30 seconds. \r\n"); wait(1); //add elapsed time debug_pc.printf("Checking network connectrion. \r\n"); GetCSQResponse(); red_LED = !red_LED; } debug_pc.printf("Network detected. Checking authorization...\r\n"); skywire.printf("AT+CEREG?\r"); WaitForResponse("OK"); //debug_pc.printf("Connecting to Network...\r\n"); debug_pc.printf("Setting up socket...\r\n"); skywire.printf("AT+SQNSCFG=3,3,300,90,600,50\r"); WaitForResponse("OK"); red_LED = 1; green_LED = 0; while(1) { // Green on to indicate code position // Start of loop. Either entered loop for the first time or just sent to dweet.io red_LED = 0; green_LED = 1; int retries = 0; while (retries < 5) { skywire.printf("AT+SQNSD=3,0,80,\"dweet.io\"\r"); if (WaitForResponse("CONNECT") == 1) { retries += 1; wait(1); } else break; } //get temp and humi temp=SHT30.cTemp(); humi=SHT30.humidity(); photo_trans_nEN=0; photo=photo_trans*200; wait(1); // Check buttons for presses if (button1 == 0) sw1 = 1; else sw1 = 0; // Green on to indicate code position: // Sensors updated, have not sent to dweet.io red_LED = 1; green_LED = 0; if (retries != 5) { debug_pc.printf("Sending information...\r\n"); // Report the sensor data to dweet.io skywire.printf("POST /dweet/for/%s?temp=%.3f&sw1=%d&photo=%.3f&humidity=%.3f HTTP/1.0\r\n\r\n", DeviceID, temp, sw1, photo, humi); WaitForResponse("NO CARRIER"); } // } debug_pc.printf("Closing socket...\r\n"); skywire.printf("AT+SQNSH=3\r"); WaitForResponse("OK"); skywire.printf("AT+CGATT=0\r"); WaitForResponse("OK"); skywire.printf("AT+CGATT=1\r"); WaitForResponse("+CEREG: 1"); red_LED = 0; green_LED = 1; } }