ceri clatworthy

Activity

Reply to -
ceri clatworthy - 24 Mar 2012
Reply to LED recommendation - You are very close to the max output current of MBED. (pin) If you only …
ceri clatworthy - 24 Mar 2012
Reply to Can I sink 12V @ 15mA through an mbed pin? - Please do not do that ! You need a transistor and probably a fly-back diode. …
ceri clatworthy - 24 Mar 2012
Reply to Can I sink 12V @ 15mA through an mbed pin? - No
ceri clatworthy - 24 Mar 2012
Reply to Can I sink 12V @ 15mA through an mbed pin? - A simple transistor, at most 25p, MBED £40, No comparison Ceri
ceri clatworthy - 23 Mar 2012
Reply to macro to switch between LPC11U24 and LPC1768 - This does work: char Chip; #ifdef TARGET_LPC11U24 Chip = 0x10; #endif #ifdef TARGET_LPC1768 Chip = …
ceri clatworthy - 22 Mar 2012
Reply to Ethernet PHY - MBED lpc1768MBED 2368My LPC1768'J' - PHYleaded PHY p1.8 - crsp1.8 - crsp1.8crs/dv led cfgcrs/dv led …
ceri clatworthy - 22 Mar 2012
Reply to Ethernet PHY - Just done a comparison betwwen the conections of LPC1768/LPC2368 MBED's and the respective PHY chips, …
ceri clatworthy - 22 Mar 2012
Reply to Ethernet PHY - How much was the license ? Cheers Ceri.
ceri clatworthy - 21 Mar 2012
Reply to Ethernet PHY - just copied it to KEIL, TOO BIG to compile ?
ceri clatworthy - 21 Mar 2012
Reply to Ethernet PHY - When i get back thisafternoon, will patch out RJ45 connector to my coolcomponents board, forgot …
ceri clatworthy - 21 Mar 2012
Reply to Ethernet PHY - the code ran on both boards, the IVV part came back with an error message …
ceri clatworthy - 21 Mar 2012
Reply to Ethernet PHY - Thanks for code, but I tryed it, and still frozen. My version, has the same …
ceri clatworthy - 21 Mar 2012
Reply to Ethernet PHY - AAAAARRRRRRRRRRRRRRRRGGGGGGGGGGGGGGGGGGGGGGGGG !!!!!!!!!!!!! What did you do to make that work ?? on the board with …
ceri clatworthy - 21 Mar 2012
Reply to Ethernet PHY - Thanks, Giuseppe Zangari wrote: That board is amazing for prototyping! I aim to please :) …
ceri clatworthy - 20 Mar 2012
Reply to Ethernet PHY - Finaly got the IVV part, solderd it down, added the 3 'missing' resistors, Flashed the …
ceri clatworthy - 20 Mar 2012
Reply to User defined Code Formatting - Me 2 { Me 2, } What about brace matching ? I think code folding …
ceri clatworthy - 19 Mar 2012
Reply to Serial comms to PC using Serial tx/rx - if you power the MAX232 from 3V3, then I/O lines will be 3V3, so no …
ceri clatworthy - 19 Mar 2012
Reply to LED recommendation - The formulae is simple: V drop for LED = 3.3 - LED Voltage. R = …
ceri clatworthy - 18 Mar 2012
Reply to LED recommendation - The brightness is in MCD Milli Candella or lumins. Try searching for hyper bright. I …
ceri clatworthy - 18 Mar 2012