Diff: examples/UdpClient/UdpClient.ino

Revision:

0:e3fb1267e3c3

Child:

6:f092f8b320ae

diff -r 000000000000 -r e3fb1267e3c3 examples/UdpClient/UdpClient.ino
--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/examples/UdpClient/UdpClient.ino	Wed Dec 21 16:58:10 2016 +0100
@@ -0,0 +1,108 @@
+/*
+ * UIPEthernet UdpClient example.
+ *
+ * UIPEthernet is a TCP/IP stack that can be used with a enc28j60 based
+ * Ethernet-shield.
+ *
+ * UIPEthernet uses the fine uIP stack by Adam Dunkels <adam@sics.se>
+ *
+ *      -----------------
+ *
+ * This UdpClient example tries to send a packet via udp to 192.168.0.1
+ * on port 5000 every 5 seconds. After successfully sending the packet it
+ * waits for up to 5 seconds for a response on the local port that has been
+ * implicitly opened when sending the packet.
+ *
+ * Copyright (C) 2013 by Norbert Truchsess (norbert.truchsess@t-online.de)
+ */
+
+#include <UIPEthernet.h>
+#include "utility/logging.h"
+
+EthernetUDP udp;
+unsigned long next;
+
+void setup() {
+
+  #if ACTLOGLEVEL>LOG_NONE
+    LogObject.begin(9600);
+  #endif
+
+  uint8_t mac[6] = {0x00,0x01,0x02,0x03,0x04,0x05};
+
+  Ethernet.begin(mac,IPAddress(192,168,0,6));
+
+  next = millis()+5000;
+}
+
+void loop() {
+
+  int success;
+  int len = 0;
+
+  if (((signed long)(millis()-next))>0)
+    {
+      do
+        {
+          success = udp.beginPacket(IPAddress(192,168,0,1),5000);
+          #if ACTLOGLEVEL>=LOG_INFO
+            LogObject.uart_send_str(F("beginPacket: "));
+            LogObject.uart_send_strln(success ? "success" : "failed");
+          #endif
+          //beginPacket fails if remote ethaddr is unknown. In this case an
+          //arp-request is send out first and beginPacket succeeds as soon
+          //the arp-response is received.
+        }
+      while (!success && ((signed long)(millis()-next))<0);
+      if (!success )
+        goto stop;
+
+      success = udp.write("hello world from arduino");
+
+      #if ACTLOGLEVEL>=LOG_INFO
+        LogObject.uart_send_str(F("bytes written: "));
+        LogObject.uart_send_decln(success);
+      #endif
+
+      success = udp.endPacket();
+
+      #if ACTLOGLEVEL>=LOG_INFO
+        LogObject.uart_send_str(F("endPacket: "));
+        LogObject.uart_send_strln(success ? "success" : "failed");
+      #endif
+
+      do
+        {
+          //check for new udp-packet:
+          success = udp.parsePacket();
+        }
+      while (!success && ((signed long)(millis()-next))<0);
+      if (!success )
+        goto stop;
+
+      #if ACTLOGLEVEL>=LOG_INFO
+        LogObject.uart_send_str(F("received: '"));
+      #endif
+      do
+        {
+          int c = udp.read();
+          #if ACTLOGLEVEL>=LOG_INFO
+            LogObject.write(c);
+          #endif
+          len++;
+        }
+      while ((success = udp.available())>0);
+      #if ACTLOGLEVEL>=LOG_INFO
+        LogObject.uart_send_str(F("', "));
+        LogObject.uart_send_dec(len);
+        LogObject.uart_send_strln(F(" bytes"));
+      #endif
+
+      //finish reading this packet:
+      udp.flush();
+
+      stop:
+      udp.stop();
+      next = millis()+5000;
+    }
+}