File content as of revision 0:78ca29b4c49e:

#include "mbed.h"
#include "math.h"
//------------------------------------------
#define PI 3.1415927f
//------------------------------------------
#include "EncoderCounter.h"
#include "DiffCounter.h"
#include "IIR_filter.h"
#include "LinearCharacteristics.h"
#include "PI_Cntrl.h"
/* Cuboid balance on one edge on Nucleo F446RE

 **** IMPORTANT: use ..\Labormodelle\RT-MOD054 - Würfel\Escon_Parameter_4nucleo.edc 
                 settings for Maxon ESCON controller (upload via ESCON Studio) ****
hardware Connections:
 
 CN7                    CN10
  :                         :
  :                         :
 ..                        ..
 ..                        ..                  15.
 ..    AOUT i_des on (PA_5)o.
 ..                        ..
 ..                        ..
 ..               ENC CH A o.
 o. GND                    ..                  10.
 o. ENC CH B               ..
 ..                        ..
 ..                        ..
 .o AIN acx (PA_0)         ..
 .o AIN acy (PA_1)         ..                  5.
 .o AIN Gyro(PA_4)         .o Analog GND
 ..                        ..
 ..                        ..
 ..                        ..                  1.
 ----------------------------
 CN7               CN10
 */
Serial pc(SERIAL_TX, SERIAL_RX);        // serial connection via USB - programmer
InterruptIn button(USER_BUTTON);        // User Button, short presses: reduce speed, long presses: increase speed
AnalogIn ax(PA_0);                      // Analog IN (acc x) on PA_0
AnalogIn ay(PA_1);                      // Analog IN (acc y) on PA_1
AnalogIn gz(PA_4);                      // Analog IN (gyr z) on PA_4
AnalogOut out(PA_5);                    // Analog OUT on PA_5   1.6 V -> 0A 3.2A -> 2A (see ESCON)
float out_value = 1.6f;                 // set voltage on 1.6 V (0 A current)
float w_soll = 10.0f;                   // desired velocity
//------------------------------------------
// ... here define variables like gains etc.
//------------------------------------------

//------------------------------------------
Ticker  ControllerLoopTimer;            // interrupt for control loop
EncoderCounter counter1(PB_6, PB_7);    // initialize counter on PB_6 and PB_7
DiffCounter diff(0.01,Ts);              // discrete differentiate, based on encoder data
//------------------------------------------
// ... here define instantiate classes
//------------------------------------------

// ... define some linear characteristics -----------------------------------------

// ----- User defined functions -----------
void updateControllers(void);   // speed controller loop (via interrupt)
// ------ END User defined functions ------

//******************************************************************************
//---------- main loop -------------
//******************************************************************************
int main()
{
    //attach controller loop to timer interrupt
    pc.baud(2000000);   // for serial comm.
    counter1.reset();   // encoder reset
    diff.reset(0.0f,0.0f);
    ControllerLoopTimer.attach(&updateControllers, Ts); //Assume Fs = ...;
}
//******************************************************************************
//---------- control loop (called via interrupt) -------------
//******************************************************************************
void updateControllers(void){
    short counts = counter1;            // get counts from Encoder
    float vel = diff(counts);           // motor velocity 
    
    // ... your code 
    
    if(++k >= 199){
        k = 0;
        pc.printf("omega_soll=%3.2f omega=%3.2f \r\n",w_soll,vel);
    }
}
//******************************************************************************
//********** User functions like buttens handle etc. **************
//******************************************************************************
// pressed button
//******************************************************************************

//...