Vybhav Kadaba / Mbed OS EV-PRO-MW1001_Development_v11570

Mbed FW update

inc/admw1001/admw1001_config.h@61:0f16a2e3b58b, 2020-03-31 (annotated)

Committer:
Vkadaba
Date:
Tue Mar 31 04:50:37 2020 +0000
Revision:
61:0f16a2e3b58b
Parent:
50:d84305e5e1c0 
removed crc support for LUT

Who changed what in which revision?

UserRevisionLine numberNew contents of line
Vkadaba 5:0728bde67bdb 1 /*
Vkadaba 6:9d393a9677f4 2 Copyright 2019 (c) Analog Devices, Inc.
Vkadaba 5:0728bde67bdb 3
Vkadaba 5:0728bde67bdb 4 All rights reserved.
Vkadaba 5:0728bde67bdb 5
Vkadaba 5:0728bde67bdb 6 Redistribution and use in source and binary forms, with or without
Vkadaba 5:0728bde67bdb 7 modification, are permitted provided that the following conditions are met:
Vkadaba 5:0728bde67bdb 8 - Redistributions of source code must retain the above copyright
Vkadaba 5:0728bde67bdb 9 notice, this list of conditions and the following disclaimer.
Vkadaba 5:0728bde67bdb 10 - Redistributions in binary form must reproduce the above copyright
Vkadaba 5:0728bde67bdb 11 notice, this list of conditions and the following disclaimer in
Vkadaba 5:0728bde67bdb 12 the documentation and/or other materials provided with the
Vkadaba 5:0728bde67bdb 13 distribution.
Vkadaba 5:0728bde67bdb 14 - Neither the name of Analog Devices, Inc. nor the names of its
Vkadaba 5:0728bde67bdb 15 contributors may be used to endorse or promote products derived
Vkadaba 5:0728bde67bdb 16 from this software without specific prior written permission.
Vkadaba 5:0728bde67bdb 17 - The use of this software may or may not infringe the patent rights
Vkadaba 5:0728bde67bdb 18 of one or more patent holders. This license does not release you
Vkadaba 5:0728bde67bdb 19 from the requirement that you obtain separate licenses from these
Vkadaba 5:0728bde67bdb 20 patent holders to use this software.
Vkadaba 5:0728bde67bdb 21 - Use of the software either in source or binary form, must be run
Vkadaba 5:0728bde67bdb 22 on or directly connected to an Analog Devices Inc. component.
Vkadaba 5:0728bde67bdb 23
Vkadaba 5:0728bde67bdb 24 THIS SOFTWARE IS PROVIDED BY ANALOG DEVICES "AS IS" AND ANY EXPRESS OR
Vkadaba 5:0728bde67bdb 25 IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, NON-INFRINGEMENT,
Vkadaba 5:0728bde67bdb 26 MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
Vkadaba 5:0728bde67bdb 27 IN NO EVENT SHALL ANALOG DEVICES BE LIABLE FOR ANY DIRECT, INDIRECT,
Vkadaba 5:0728bde67bdb 28 INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
Vkadaba 5:0728bde67bdb 29 LIMITED TO, INTELLECTUAL PROPERTY RIGHTS, PROCUREMENT OF SUBSTITUTE GOODS OR
Vkadaba 5:0728bde67bdb 30 SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
Vkadaba 5:0728bde67bdb 31 CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
Vkadaba 5:0728bde67bdb 32 OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
Vkadaba 5:0728bde67bdb 33 OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
Vkadaba 5:0728bde67bdb 34 */
Vkadaba 5:0728bde67bdb 35
Vkadaba 5:0728bde67bdb 36 /*!
Vkadaba 5:0728bde67bdb 37 ******************************************************************************
Vkadaba 5:0728bde67bdb 38 * @file: admw1001_config.h
Vkadaba 5:0728bde67bdb 39 * @brief: Configuration type definitions for ADMW1001.
Vkadaba 5:0728bde67bdb 40 *-----------------------------------------------------------------------------
Vkadaba 5:0728bde67bdb 41 */
Vkadaba 5:0728bde67bdb 42
Vkadaba 5:0728bde67bdb 43 #ifndef __ADMW1001_CONFIG_H__
Vkadaba 5:0728bde67bdb 44 #define __ADMW1001_CONFIG_H__
Vkadaba 5:0728bde67bdb 45
Vkadaba 5:0728bde67bdb 46 #include "admw_platform.h"
Vkadaba 5:0728bde67bdb 47 #include "admw1001_sensor_types.h"
Vkadaba 5:0728bde67bdb 48
Vkadaba 5:0728bde67bdb 49 /*! @addtogroup ADMW1001_Api
Vkadaba 5:0728bde67bdb 50 * @{
Vkadaba 5:0728bde67bdb 51 */
Vkadaba 5:0728bde67bdb 52
Vkadaba 5:0728bde67bdb 53 #ifdef __cplusplus
Vkadaba 5:0728bde67bdb 54 extern "C" {
Vkadaba 5:0728bde67bdb 55 #endif
Vkadaba 5:0728bde67bdb 56
Vkadaba 5:0728bde67bdb 57 /*! Maximum length allowed for a digital sensor command */
Vkadaba 5:0728bde67bdb 58 #define ADMW1001_SENSOR_COMMAND_MAX_LENGTH 7
Vkadaba 5:0728bde67bdb 59
Vkadaba 5:0728bde67bdb 60 /*! ADMW1001 channel priority options */
Vkadaba 45:f5f553b8c0d5 61 typedef enum
Vkadaba 45:f5f553b8c0d5 62 {
Vkadaba 5:0728bde67bdb 63 ADMW1001_CHANNEL_PRIORITY_0 = 0,
Vkadaba 5:0728bde67bdb 64 ADMW1001_CHANNEL_PRIORITY_1,
Vkadaba 5:0728bde67bdb 65 ADMW1001_CHANNEL_PRIORITY_2,
Vkadaba 5:0728bde67bdb 66 ADMW1001_CHANNEL_PRIORITY_3,
Vkadaba 5:0728bde67bdb 67 ADMW1001_CHANNEL_PRIORITY_4,
Vkadaba 5:0728bde67bdb 68 ADMW1001_CHANNEL_PRIORITY_5,
Vkadaba 5:0728bde67bdb 69 ADMW1001_CHANNEL_PRIORITY_6,
Vkadaba 5:0728bde67bdb 70 ADMW1001_CHANNEL_PRIORITY_7,
Vkadaba 5:0728bde67bdb 71 ADMW1001_CHANNEL_PRIORITY_8,
Vkadaba 5:0728bde67bdb 72 ADMW1001_CHANNEL_PRIORITY_9,
Vkadaba 5:0728bde67bdb 73 ADMW1001_CHANNEL_PRIORITY_10,
Vkadaba 5:0728bde67bdb 74 ADMW1001_CHANNEL_PRIORITY_11,
Vkadaba 5:0728bde67bdb 75 ADMW1001_CHANNEL_PRIORITY_12,
Vkadaba 5:0728bde67bdb 76
Vkadaba 5:0728bde67bdb 77 ADMW1001_CHANNEL_PRIORITY_HIGHEST = ADMW1001_CHANNEL_PRIORITY_0,
Vkadaba 8:2f2775c34640 78 ADMW1001_CHANNEL_PRIORITY_LOWEST = ADMW1001_CHANNEL_PRIORITY_12,
Vkadaba 8:2f2775c34640 79
Vkadaba 8:2f2775c34640 80 } ADMW1001_CHANNEL_PRIORITY;
Vkadaba 5:0728bde67bdb 81
Vkadaba 5:0728bde67bdb 82 /*! ADMW1001 operating mode options */
Vkadaba 45:f5f553b8c0d5 83 typedef enum
Vkadaba 45:f5f553b8c0d5 84 {
Vkadaba 5:0728bde67bdb 85 ADMW1001_OPERATING_MODE_SINGLECYCLE = 0,
Vkadaba 5:0728bde67bdb 86 /*!< Executes a single measurement cycle and stops */
Vkadaba 5:0728bde67bdb 87 ADMW1001_OPERATING_MODE_CONTINUOUS,
Vkadaba 5:0728bde67bdb 88 /*!< Continuously executes measurement cycles */
Vkadaba 5:0728bde67bdb 89 ADMW1001_OPERATING_MODE_MULTICYCLE,
Vkadaba 5:0728bde67bdb 90 /*!< Executes a burst of measurement cycles, repeated at defined intervals */
Vkadaba 8:2f2775c34640 91
Vkadaba 8:2f2775c34640 92 } ADMW1001_OPERATING_MODE;
Vkadaba 5:0728bde67bdb 93
Vkadaba 5:0728bde67bdb 94 /*! ADMW1001 data ready mode options */
Vkadaba 45:f5f553b8c0d5 95 typedef enum
Vkadaba 45:f5f553b8c0d5 96 {
Vkadaba 5:0728bde67bdb 97 ADMW1001_DATAREADY_PER_CONVERSION = 0,
Vkadaba 5:0728bde67bdb 98 /*!< The DATAREADY signal is asserted after completion of each conversion
Vkadaba 5:0728bde67bdb 99 * - a single data sample only from the latest completed conversion is
Vkadaba 5:0728bde67bdb 100 * stored in this mode
Vkadaba 5:0728bde67bdb 101 */
Vkadaba 5:0728bde67bdb 102 ADMW1001_DATAREADY_PER_CYCLE,
Vkadaba 5:0728bde67bdb 103 /*!< The DATAREADY signal is asserted after completion of each measurement
Vkadaba 5:0728bde67bdb 104 * cycle
Vkadaba 5:0728bde67bdb 105 * - data samples only from the lastest completed measurement cycle are
Vkadaba 5:0728bde67bdb 106 * stored in this mode
Vkadaba 5:0728bde67bdb 107 */
Vkadaba 8:2f2775c34640 108 ADMW1001_DATAREADY_PER_FIFO_FILL,
Vkadaba 8:2f2775c34640 109 /*!< The DATAREADY signal is asserted after each fill of the data FIFO
Vkadaba 8:2f2775c34640 110 * - applicable only when @ref ADMW1001_OPERATING_MODE_CONTINUOUS or
Vkadaba 8:2f2775c34640 111 * @ref ADMW1001_OPERATING_MODE_MULTICYCLE is also selected
Vkadaba 5:0728bde67bdb 112 */
Vkadaba 8:2f2775c34640 113
Vkadaba 8:2f2775c34640 114 } ADMW1001_DATAREADY_MODE;
Vkadaba 5:0728bde67bdb 115
Vkadaba 5:0728bde67bdb 116 /*! ADMW1001 power mode options */
Vkadaba 45:f5f553b8c0d5 117 typedef enum
Vkadaba 45:f5f553b8c0d5 118 {
Vkadaba 50:d84305e5e1c0 119 ADMW1001_POWER_MODE_ACTIVE = 0,
Vkadaba 50:d84305e5e1c0 120 /*!< Part is fully powered up and either cycling through a sequence or awaiting a configuration */
Vkadaba 50:d84305e5e1c0 121 ADMW1001_POWER_MODE_HIBERNATION,
Vkadaba 6:9d393a9677f4 122 /*!< module has entede hibernation mode. All analog circuitry is disabled. All peripherals disabled apart from the Wake-up pin functionality. */
Vkadaba 5:0728bde67bdb 123
Vkadaba 8:2f2775c34640 124 } ADMW1001_POWER_MODE;
Vkadaba 8:2f2775c34640 125
Vkadaba 5:0728bde67bdb 126 /*! ADMW1001 measurement analog filter settling options */
Vkadaba 45:f5f553b8c0d5 127 typedef enum
Vkadaba 45:f5f553b8c0d5 128 {
Vkadaba 5:0728bde67bdb 129 ADMW1001_FILTER_SETTLING_ALWAYS = 0,
Vkadaba 5:0728bde67bdb 130 /*!< Allow full settling time to elapse between every measurement from an analog sensor */
Vkadaba 6:9d393a9677f4 131 ADMW1001_FILTER_SETTLING_FAST,
Vkadaba 5:0728bde67bdb 132 /*!< Skip settling time between consecutive measurements from an analog sensor */
Vkadaba 8:2f2775c34640 133
Vkadaba 8:2f2775c34640 134 } ADMW1001_FILTER_SETTLING;
Vkadaba 5:0728bde67bdb 135
Vkadaba 5:0728bde67bdb 136 /*! ADMW1001 measurement unit options
Vkadaba 5:0728bde67bdb 137 *
Vkadaba 5:0728bde67bdb 138 * Optionally select a measurement unit for final conversion results.
Vkadaba 5:0728bde67bdb 139 * Currently applicable only to specific temperature sensor types.
Vkadaba 5:0728bde67bdb 140 */
Vkadaba 45:f5f553b8c0d5 141 typedef enum
Vkadaba 45:f5f553b8c0d5 142 {
Vkadaba 5:0728bde67bdb 143 ADMW1001_MEASUREMENT_UNIT_UNSPECIFIED = 0,
Vkadaba 5:0728bde67bdb 144 /*!< No measurement unit specified */
Vkadaba 5:0728bde67bdb 145 ADMW1001_MEASUREMENT_UNIT_CELSIUS,
Vkadaba 5:0728bde67bdb 146 /*!< Celsius temperature unit - applicable to temperature sensors only */
Vkadaba 5:0728bde67bdb 147 ADMW1001_MEASUREMENT_UNIT_FAHRENHEIT,
Vkadaba 5:0728bde67bdb 148 /*!< Fahrenheit temperature unit - applicable to temperature sensors only */
Vkadaba 8:2f2775c34640 149
Vkadaba 8:2f2775c34640 150 } ADMW1001_MEASUREMENT_UNIT;
Vkadaba 5:0728bde67bdb 151
Vkadaba 45:f5f553b8c0d5 152 typedef enum
Vkadaba 45:f5f553b8c0d5 153 {
Vkadaba 33:df7a00f1b8e1 154 ADMW1001_BUFFER_BYPASSS_DISABLED = 0,
Vkadaba 33:df7a00f1b8e1 155 /*!< Buffer Bypass Disabled */
Vkadaba 33:df7a00f1b8e1 156 ADMW1001_BUFFER_BYPASSS_ENABLED,
Vkadaba 33:df7a00f1b8e1 157 /*!< Buffer Bypass Enabled */
Vkadaba 34:b60ee1e0af2b 158
Vkadaba 33:df7a00f1b8e1 159 } ADMW1001_BUFFER_BYPASSS;
Vkadaba 33:df7a00f1b8e1 160
Vkadaba 5:0728bde67bdb 161 /*! ADMW1001 analog input signal amplification gain options
Vkadaba 5:0728bde67bdb 162 *
Vkadaba 5:0728bde67bdb 163 * @note applicable only to ADC analog sensor channels
Vkadaba 5:0728bde67bdb 164 */
Vkadaba 45:f5f553b8c0d5 165 typedef enum
Vkadaba 45:f5f553b8c0d5 166 {
Vkadaba 6:9d393a9677f4 167 ADMW1001_ADC_RTD_CURVE_EUROPEAN = 0,
Vkadaba 6:9d393a9677f4 168 /*!< EUROPEAN RTD curve used. */
Vkadaba 6:9d393a9677f4 169 ADMW1001_ADC_RTD_CURVE_AMERICAN,
Vkadaba 6:9d393a9677f4 170 /*!< AMERICAN RTD curve used. */
Vkadaba 6:9d393a9677f4 171 ADMW1001_ADC_RTD_CURVE_JAPANESE,
Vkadaba 6:9d393a9677f4 172 /*!< JAPANESE RTD curve used. */
Vkadaba 6:9d393a9677f4 173 ADMW1001_ADC_RTD_CURVE_ITS90,
Vkadaba 6:9d393a9677f4 174 /*!< ITS90 RTD curve used. */
Vkadaba 8:2f2775c34640 175
Vkadaba 8:2f2775c34640 176 } ADMW1001_ADC_RTD_CURVE;
Vkadaba 6:9d393a9677f4 177 /*! ADMW1001 analog input signal amplification gain options
Vkadaba 6:9d393a9677f4 178 *
Vkadaba 6:9d393a9677f4 179 * @note applicable only to ADC analog sensor channels
Vkadaba 6:9d393a9677f4 180 */
Vkadaba 45:f5f553b8c0d5 181 typedef enum
Vkadaba 45:f5f553b8c0d5 182 {
Vkadaba 5:0728bde67bdb 183 ADMW1001_ADC_GAIN_1X = 0,
Vkadaba 5:0728bde67bdb 184 /*!< no amplification gain */
Vkadaba 5:0728bde67bdb 185 ADMW1001_ADC_GAIN_2X,
Vkadaba 5:0728bde67bdb 186 /*!< x2 amplification gain */
Vkadaba 5:0728bde67bdb 187 ADMW1001_ADC_GAIN_4X,
Vkadaba 5:0728bde67bdb 188 /*!< x4 amplification gain */
Vkadaba 5:0728bde67bdb 189 ADMW1001_ADC_GAIN_8X,
Vkadaba 5:0728bde67bdb 190 /*!< x8 amplification gain */
Vkadaba 5:0728bde67bdb 191 ADMW1001_ADC_GAIN_16X,
Vkadaba 5:0728bde67bdb 192 /*!< x16 amplification gain */
Vkadaba 5:0728bde67bdb 193 ADMW1001_ADC_GAIN_32X,
Vkadaba 5:0728bde67bdb 194 /*!< x32 amplification gain */
Vkadaba 5:0728bde67bdb 195 ADMW1001_ADC_GAIN_64X,
Vkadaba 5:0728bde67bdb 196 /*!< x64 amplification gain */
Vkadaba 5:0728bde67bdb 197 ADMW1001_ADC_GAIN_128X,
Vkadaba 5:0728bde67bdb 198 /*!< x128 amplification gain */
Vkadaba 8:2f2775c34640 199
Vkadaba 8:2f2775c34640 200 } ADMW1001_ADC_GAIN;
Vkadaba 5:0728bde67bdb 201
Vkadaba 6:9d393a9677f4 202 /*! ADMW1001 analog sensor excitation state options
Vkadaba 6:9d393a9677f4 203 *
Vkadaba 6:9d393a9677f4 204 * @note applicable only to ADC analog sensor channels, and
Vkadaba 6:9d393a9677f4 205 * specific sensor types
Vkadaba 6:9d393a9677f4 206 */
Vkadaba 45:f5f553b8c0d5 207 typedef enum
Vkadaba 45:f5f553b8c0d5 208 {
Vkadaba 45:f5f553b8c0d5 209 ADMW1001_ADC_EXC_STATE_CYCLE_POWER = 0,
Vkadaba 33:df7a00f1b8e1 210 /*!< Excitation for measurement is active only during measurement */
Vkadaba 6:9d393a9677f4 211 ADMW1001_ADC_EXC_STATE_ALWAYS_ON,
Vkadaba 6:9d393a9677f4 212 /*!< Excitation for measurement is always on */
Vkadaba 45:f5f553b8c0d5 213
Vkadaba 8:2f2775c34640 214 } ADMW1001_ADC_EXC_STATE;
Vkadaba 6:9d393a9677f4 215
Vkadaba 5:0728bde67bdb 216 /*! ADMW1001 analog sensor excitation current output level options
Vkadaba 5:0728bde67bdb 217 *
Vkadaba 5:0728bde67bdb 218 * @note applicable only to ADC analog sensor channels, and
Vkadaba 5:0728bde67bdb 219 * specific sensor types
Vkadaba 5:0728bde67bdb 220 */
Vkadaba 45:f5f553b8c0d5 221 typedef enum
Vkadaba 45:f5f553b8c0d5 222 {
Vkadaba 18:cbf514cce921 223 ADMW1001_ADC_NO_EXTERNAL_EXC_CURRENT = -1,
Vkadaba 34:b60ee1e0af2b 224 /*!< NO External excitation is provided */
Vkadaba 6:9d393a9677f4 225 ADMW1001_ADC_EXC_CURRENT_EXTERNAL = 0,
Vkadaba 34:b60ee1e0af2b 226 /*!< External excitation is provided */
Vkadaba 5:0728bde67bdb 227 ADMW1001_ADC_EXC_CURRENT_50uA,
Vkadaba 5:0728bde67bdb 228 /*!< 50uA excitation current enabled */
Vkadaba 5:0728bde67bdb 229 ADMW1001_ADC_EXC_CURRENT_100uA,
Vkadaba 5:0728bde67bdb 230 /*!< 100uA excitation current */
Vkadaba 5:0728bde67bdb 231 ADMW1001_ADC_EXC_CURRENT_250uA,
Vkadaba 5:0728bde67bdb 232 /*!< 250uA excitation current enabled */
Vkadaba 5:0728bde67bdb 233 ADMW1001_ADC_EXC_CURRENT_500uA,
Vkadaba 5:0728bde67bdb 234 /*!< 500uA excitation current enabled */
Vkadaba 5:0728bde67bdb 235 ADMW1001_ADC_EXC_CURRENT_1000uA,
Vkadaba 5:0728bde67bdb 236 /*!< 1mA excitation current enabled */
Vkadaba 8:2f2775c34640 237
Vkadaba 8:2f2775c34640 238 } ADMW1001_ADC_EXC_CURRENT;
Vkadaba 5:0728bde67bdb 239
Vkadaba 5:0728bde67bdb 240 /*! ADMW1001 analog sensor excitation current ratios used for diode sensor
Vkadaba 5:0728bde67bdb 241 *
Vkadaba 5:0728bde67bdb 242 * @note applicable only to a diode sensor
Vkadaba 5:0728bde67bdb 243 */
Vkadaba 45:f5f553b8c0d5 244 typedef enum
Vkadaba 45:f5f553b8c0d5 245 {
Vkadaba 34:b60ee1e0af2b 246 ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_10UA_100UA = 0,
Vkadaba 6:9d393a9677f4 247 /**< 2 Current measurement 10uA 100uA */
Vkadaba 34:b60ee1e0af2b 248 ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_20UA_160UA,
Vkadaba 6:9d393a9677f4 249 /**< 2 Current measurement 20uA 160uA */
Vkadaba 34:b60ee1e0af2b 250 ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_50UA_300UA,
Vkadaba 6:9d393a9677f4 251 /**< 2 Current measurement 50uA 300uA */
Vkadaba 34:b60ee1e0af2b 252 ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_100UA_600UA,
Vkadaba 6:9d393a9677f4 253 /**< 2 Current measurement 100uA 600uA */
Vkadaba 34:b60ee1e0af2b 254 ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_10UA_50UA_100UA,
Vkadaba 6:9d393a9677f4 255 /**< 3 current measuremetn 10uA 50uA 100uA */
Vkadaba 34:b60ee1e0af2b 256 ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_20UA_100UA_160UA,
Vkadaba 6:9d393a9677f4 257 /**< 3 current measuremetn 20uA 100uA 160uA */
Vkadaba 34:b60ee1e0af2b 258 ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_50UA_150UA_300UA,
Vkadaba 6:9d393a9677f4 259 /**< 3 current measuremetn 50uA 150uA 300uA */
Vkadaba 6:9d393a9677f4 260 ADMW1001_ADC_EXC_CURRENT_IOUT_DIODE_100UA_300UA_600UA,
Vkadaba 6:9d393a9677f4 261 /**< 3 current measuremetn 100uA 300uA 600uA */
Vkadaba 8:2f2775c34640 262
Vkadaba 8:2f2775c34640 263 } ADMW1001_ADC_EXC_CURRENT_DIODE_RATIO;
Vkadaba 5:0728bde67bdb 264
Vkadaba 5:0728bde67bdb 265 /*! ADMW1001 analog reference selection options
Vkadaba 5:0728bde67bdb 266 *
Vkadaba 5:0728bde67bdb 267 * @note applicable only to ADC analog sensor channels, and
Vkadaba 5:0728bde67bdb 268 * specific sensor types
Vkadaba 5:0728bde67bdb 269 */
Vkadaba 45:f5f553b8c0d5 270 typedef enum
Vkadaba 45:f5f553b8c0d5 271 {
Vkadaba 8:2f2775c34640 272 ADMW1001_ADC_REFERENCE_VOLTAGE_INTERNAL = 0,
Vkadaba 8:2f2775c34640 273 /*!< Internal VRef - 1.2V */
Vkadaba 61:0f16a2e3b58b 274 ADMW1001_ADC_REFERENCE_VOLTAGE_EXTERNAL_1 = 1,
Vkadaba 8:2f2775c34640 275 /*!< External reference voltage #1 */
Vkadaba 61:0f16a2e3b58b 276 ADMW1001_ADC_REFERENCE_VOLTAGE_AVDD = 3,
Vkadaba 61:0f16a2e3b58b 277 /*!< Analog Supply Voltage AVDD reference (typically 3.3V) is selected */
Vkadaba 5:0728bde67bdb 278
Vkadaba 8:2f2775c34640 279 } ADMW1001_ADC_REFERENCE_TYPE;
Vkadaba 5:0728bde67bdb 280
Vkadaba 6:9d393a9677f4 281 /*! ADMW1001 ADC Reference configuration
Vkadaba 6:9d393a9677f4 282 *
Vkadaba 6:9d393a9677f4 283 * @note applicable only to ADC analog sensor channels
Vkadaba 6:9d393a9677f4 284 */
Vkadaba 45:f5f553b8c0d5 285 typedef enum
Vkadaba 45:f5f553b8c0d5 286 {
Vkadaba 6:9d393a9677f4 287 ADMW1001_ADC_GND_SW_OPEN = 0,
Vkadaba 6:9d393a9677f4 288 /*!< Ground switch not enabled for measurement. */
Vkadaba 6:9d393a9677f4 289 ADMW1001_ADC_GND_SW_CLOSED,
Vkadaba 8:2f2775c34640 290 /*!< Ground switch enabled for measurement. */
Vkadaba 8:2f2775c34640 291
Vkadaba 8:2f2775c34640 292 } ADMW1001_ADC_GND_SW;
Vkadaba 8:2f2775c34640 293
Vkadaba 8:2f2775c34640 294 /*! ADMW1001 analog filter chop mode
Vkadaba 8:2f2775c34640 295 *
Vkadaba 8:2f2775c34640 296 * @note applicable only to ADC analog sensor channels
Vkadaba 8:2f2775c34640 297 */
Vkadaba 45:f5f553b8c0d5 298 typedef enum
Vkadaba 45:f5f553b8c0d5 299 {
Vkadaba 8:2f2775c34640 300 ADMW1001_CHOP_MD_NONE = 0,
Vkadaba 8:2f2775c34640 301 /*!< No chop performed. */
Vkadaba 8:2f2775c34640 302 ADMW1001_CHOP_MD_HW,
Vkadaba 8:2f2775c34640 303 /*!< Hardware only chop performed. */
Vkadaba 8:2f2775c34640 304 ADMW1001_CHOP_MD_SW,
Vkadaba 8:2f2775c34640 305 /*!< Software only chop performed. */
Vkadaba 8:2f2775c34640 306 ADMW1001_CHOP_MD_HWSW,
Vkadaba 8:2f2775c34640 307 /*!< Hardware and software chop performed. */
Vkadaba 34:b60ee1e0af2b 308
Vkadaba 8:2f2775c34640 309 } ADMW1001_CHOP_MD;
Vkadaba 6:9d393a9677f4 310
Vkadaba 5:0728bde67bdb 311 /*! ADMW1001 analog filter selection options
Vkadaba 5:0728bde67bdb 312 *
Vkadaba 5:0728bde67bdb 313 * @note applicable only to ADC analog sensor channels
Vkadaba 5:0728bde67bdb 314 */
Vkadaba 45:f5f553b8c0d5 315 typedef enum
Vkadaba 45:f5f553b8c0d5 316 {
Vkadaba 6:9d393a9677f4 317 ADMW1001_ADC_FILTER_SINC4 = 0,
Vkadaba 8:2f2775c34640 318 /*!< SINC4 - 4th order sinc response filter */
Vkadaba 6:9d393a9677f4 319 ADMW1001_ADC_FILTER_SINC3,
Vkadaba 8:2f2775c34640 320 /*!< SINC3 - 3rd order sinc response filter */
Vkadaba 8:2f2775c34640 321
Vkadaba 8:2f2775c34640 322 } ADMW1001_ADC_FILTER_TYPE;
Vkadaba 8:2f2775c34640 323
Vkadaba 8:2f2775c34640 324 /*! ADMW1001 Sinc Filter range (SF)
Vkadaba 8:2f2775c34640 325 *
Vkadaba 8:2f2775c34640 326 * @note applicable only to ADC analog sensor channels
Vkadaba 34:b60ee1e0af2b 327 * @note SF must be set in conjunction with chop mode
Vkadaba 8:2f2775c34640 328 * and sinc filter type to achieve the desired sampling rate.
Vkadaba 8:2f2775c34640 329 */
Vkadaba 45:f5f553b8c0d5 330 typedef enum
Vkadaba 45:f5f553b8c0d5 331 {
Vkadaba 8:2f2775c34640 332 ADMW1001_SF_976HZ = 0,
Vkadaba 8:2f2775c34640 333 /*!< SF setting for 976Hz sample rate. */
Vkadaba 8:2f2775c34640 334 ADMW1001_SF_488HZ = 1,
Vkadaba 8:2f2775c34640 335 /*!< SF setting for 488Hz sample rate. */
Vkadaba 8:2f2775c34640 336 ADMW1001_SF_244HZ = 3,
Vkadaba 8:2f2775c34640 337 /*!< SF setting for 244Hz sample rate. */
Vkadaba 8:2f2775c34640 338 ADMW1001_SF_122HZ = 7,
Vkadaba 8:2f2775c34640 339 /*!< SF setting for 122Hz sample rate. */
Vkadaba 8:2f2775c34640 340 ADMW1001_SF_61HZ = 31,
Vkadaba 8:2f2775c34640 341 /*!< SF setting for 61Hz sample rate. */
Vkadaba 8:2f2775c34640 342 ADMW1001_SF_30P5HZ = 51,
Vkadaba 8:2f2775c34640 343 /*!< SF setting for 61Hz sample rate. */
Vkadaba 8:2f2775c34640 344 ADMW1001_SF_10HZ = 124,
Vkadaba 8:2f2775c34640 345 /*!< SF setting for 10Hz sample rate. */
Vkadaba 8:2f2775c34640 346 ADMW1001_SF_8P24HZ = 125,
Vkadaba 8:2f2775c34640 347 /*!< SF setting for 8.24Hz sample rate. */
Vkadaba 8:2f2775c34640 348 ADMW1001_SF_5HZ = 127,
Vkadaba 8:2f2775c34640 349 /*!< SF setting for 5Hz sample rate. */
Vkadaba 8:2f2775c34640 350
Vkadaba 8:2f2775c34640 351 } ADMW1001_SINC_FILTER_RANGE;
Vkadaba 5:0728bde67bdb 352
Vkadaba 5:0728bde67bdb 353 /*! ADMW1001 I2C clock speed options
Vkadaba 5:0728bde67bdb 354 *
Vkadaba 5:0728bde67bdb 355 * @note applicable only for I2C sensors
Vkadaba 5:0728bde67bdb 356 */
Vkadaba 45:f5f553b8c0d5 357 typedef enum
Vkadaba 45:f5f553b8c0d5 358 {
Vkadaba 8:2f2775c34640 359 ADMW1001_DIGITAL_SENSOR_COMMS_I2C_CLOCK_SPEED_100K = 0,
Vkadaba 5:0728bde67bdb 360 /*!< 100kHz I2C clock speed */
Vkadaba 8:2f2775c34640 361 ADMW1001_DIGITAL_SENSOR_COMMS_I2C_CLOCK_SPEED_400K,
Vkadaba 5:0728bde67bdb 362 /*!< 400kHz I2C clock speed */
Vkadaba 8:2f2775c34640 363
Vkadaba 8:2f2775c34640 364 } ADMW1001_DIGITAL_SENSOR_COMMS_I2C_CLOCK_SPEED;
Vkadaba 5:0728bde67bdb 365
Vkadaba 5:0728bde67bdb 366 /*! ADMW1001 SPI mode options
Vkadaba 5:0728bde67bdb 367 *
Vkadaba 5:0728bde67bdb 368 * @note applicable only for SPI sensors
Vkadaba 5:0728bde67bdb 369 */
Vkadaba 45:f5f553b8c0d5 370 typedef enum
Vkadaba 45:f5f553b8c0d5 371 {
Vkadaba 8:2f2775c34640 372 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_MODE_0 = 0,
Vkadaba 5:0728bde67bdb 373 /*!< SPI mode 0 Clock Polarity = 0 Clock Phase = 0 */
Vkadaba 8:2f2775c34640 374 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_MODE_1,
Vkadaba 5:0728bde67bdb 375 /*!< SPI mode 0 Clock Polarity = 0 Clock Phase = 1 */
Vkadaba 8:2f2775c34640 376 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_MODE_2,
Vkadaba 5:0728bde67bdb 377 /*!< SPI mode 0 Clock Polarity = 1 Clock Phase = 0 */
Vkadaba 8:2f2775c34640 378 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_MODE_3,
Vkadaba 5:0728bde67bdb 379 /*!< SPI mode 0 Clock Polarity = 1 Clock Phase = 1 */
Vkadaba 8:2f2775c34640 380
Vkadaba 8:2f2775c34640 381 } ADMW1001_DIGITAL_SENSOR_COMMS_SPI_MODE;
Vkadaba 5:0728bde67bdb 382
Vkadaba 5:0728bde67bdb 383 /*! ADMW1001 SPI clock speed options
Vkadaba 5:0728bde67bdb 384 *
Vkadaba 5:0728bde67bdb 385 * @note applicable only for SPI sensors
Vkadaba 5:0728bde67bdb 386 */
Vkadaba 45:f5f553b8c0d5 387 typedef enum
Vkadaba 45:f5f553b8c0d5 388 {
Vkadaba 8:2f2775c34640 389 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_8MHZ = 0,
Vkadaba 8:2f2775c34640 390 /*!< SPI Clock Speed configured to 8MHz */
Vkadaba 8:2f2775c34640 391 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_4MHZ,
Vkadaba 8:2f2775c34640 392 /*!< SPI Clock Speed configured to 4MHz */
Vkadaba 8:2f2775c34640 393 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_2MHZ,
Vkadaba 8:2f2775c34640 394 /*!< SPI Clock Speed configured to 2MHz */
Vkadaba 8:2f2775c34640 395 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_1MHZ,
Vkadaba 8:2f2775c34640 396 /*!< SPI Clock Speed configured to 1MHz */
Vkadaba 8:2f2775c34640 397 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_500KHZ,
Vkadaba 8:2f2775c34640 398 /*!< SPI Clock Speed configured to 500kHz */
Vkadaba 8:2f2775c34640 399 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_250KHZ,
Vkadaba 8:2f2775c34640 400 /*!< SPI Clock Speed configured to 250kHz */
Vkadaba 8:2f2775c34640 401 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_125KHZ,
Vkadaba 8:2f2775c34640 402 /*!< SPI Clock Speed configured to 125kHz */
Vkadaba 8:2f2775c34640 403 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_62P5KHZ,
Vkadaba 8:2f2775c34640 404 /*!< SPI Clock Speed configured to 62.5kHz */
Vkadaba 8:2f2775c34640 405 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_31P3KHZ,
Vkadaba 8:2f2775c34640 406 /*!< SPI Clock Speed configured to 31.3kHz */
Vkadaba 8:2f2775c34640 407 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_15P6KHZ,
Vkadaba 8:2f2775c34640 408 /*!< SPI Clock Speed configured to 15.6kHz */
Vkadaba 8:2f2775c34640 409 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_7P8KHZ,
Vkadaba 8:2f2775c34640 410 /*!< SPI Clock Speed configured to 7.8kHz */
Vkadaba 8:2f2775c34640 411 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_3P9KHZ,
Vkadaba 8:2f2775c34640 412 /*!< SPI Clock Speed configured to 3.9kHz */
Vkadaba 8:2f2775c34640 413 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_1P9KHZ,
Vkadaba 8:2f2775c34640 414 /*!< SPI Clock Speed configured to 1.9kHz */
Vkadaba 8:2f2775c34640 415 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_977HZ,
Vkadaba 8:2f2775c34640 416 /*!< SPI Clock Speed configured to 977Hz */
Vkadaba 8:2f2775c34640 417 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_488HZ,
Vkadaba 8:2f2775c34640 418 /*!< SPI Clock Speed configured to 488Hz */
Vkadaba 8:2f2775c34640 419 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK_244HZ,
Vkadaba 8:2f2775c34640 420 /*!< SPI Clock Speed configured to 244Hz */
Vkadaba 8:2f2775c34640 421
Vkadaba 8:2f2775c34640 422 } ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK;
Vkadaba 5:0728bde67bdb 423
Vkadaba 5:0728bde67bdb 424 /*! ADMW1001 Power Configuration options */
Vkadaba 45:f5f553b8c0d5 425 typedef struct
Vkadaba 45:f5f553b8c0d5 426 {
Vkadaba 5:0728bde67bdb 427 ADMW1001_POWER_MODE powerMode;
Vkadaba 5:0728bde67bdb 428 /*!< Power mode selection */
Vkadaba 8:2f2775c34640 429
Vkadaba 8:2f2775c34640 430 } ADMW1001_POWER_CONFIG;
Vkadaba 5:0728bde67bdb 431
Vkadaba 5:0728bde67bdb 432 /*! ADMW1001 Multi-Cycle Configuration options
Vkadaba 5:0728bde67bdb 433 *
Vkadaba 5:0728bde67bdb 434 * @note required only when ADMW1001_OPERATING_MODE_MULTICYCLE is selected
Vkadaba 5:0728bde67bdb 435 * as the operatingMode (@ref ADMW1001_MEASUREMENT_CONFIG)
Vkadaba 5:0728bde67bdb 436 */
Vkadaba 45:f5f553b8c0d5 437 typedef struct
Vkadaba 45:f5f553b8c0d5 438 {
Vkadaba 8:2f2775c34640 439 uint32_t cyclesPerBurst;
Vkadaba 5:0728bde67bdb 440 /*!< Number of cycles to complete for a single burst */
Vkadaba 8:2f2775c34640 441 uint32_t burstInterval;
Vkadaba 5:0728bde67bdb 442 /*!< Interval, in seconds, between each successive burst of cycles */
Vkadaba 8:2f2775c34640 443
Vkadaba 8:2f2775c34640 444 } ADMW1001_MULTICYCLE_CONFIG;
Vkadaba 5:0728bde67bdb 445
Vkadaba 5:0728bde67bdb 446 /*! ADMW1001 Measurement Configuration options */
Vkadaba 45:f5f553b8c0d5 447 typedef struct
Vkadaba 45:f5f553b8c0d5 448 {
Vkadaba 5:0728bde67bdb 449 ADMW1001_OPERATING_MODE operatingMode;
Vkadaba 5:0728bde67bdb 450 /*!< Operating mode - specifies how measurement cycles are scheduled */
Vkadaba 5:0728bde67bdb 451 ADMW1001_DATAREADY_MODE dataReadyMode;
Vkadaba 5:0728bde67bdb 452 /*!< Data read mode - specifies how output samples are stored for reading */
Vkadaba 5:0728bde67bdb 453 ADMW1001_MULTICYCLE_CONFIG multiCycleConfig;
Vkadaba 5:0728bde67bdb 454 /*!< Multi-Cycle configuration - specifies how bursts of measurement cycles
Vkadaba 5:0728bde67bdb 455 * are scheduled. Applicable only when operatingMode is
Vkadaba 5:0728bde67bdb 456 * ADMW1001_OPERATING_MODE_MULTICYCLE
Vkadaba 5:0728bde67bdb 457 */
Vkadaba 5:0728bde67bdb 458 ADMW1001_FILTER_SETTLING filterSettling;
Vkadaba 5:0728bde67bdb 459 /*!< Analog filter settling - specifies the policy for settling time
Vkadaba 5:0728bde67bdb 460 * between consecutive measurements from an analog channel in a multi-
Vkadaba 5:0728bde67bdb 461 * channel configuration. Note that, in single analog channel
Vkadaba 5:0728bde67bdb 462 * configurations, settling time is always skipped between consecutive
Vkadaba 5:0728bde67bdb 463 * measurements in a measurement cycle.
Vkadaba 5:0728bde67bdb 464 */
Vkadaba 45:f5f553b8c0d5 465 uint8_t excitationState;
Vkadaba 43:e1789b7214cf 466 /*!< Excitation current state */
Vkadaba 45:f5f553b8c0d5 467 uint8_t groundSwitch;
Vkadaba 45:f5f553b8c0d5 468 /*!< Option to open or close sensor ground switch */
Vkadaba 50:d84305e5e1c0 469 uint8_t fifoNumCycles;
Vkadaba 50:d84305e5e1c0 470 /*!< Specifies the number of cycles to fill a FIFO buffer
Vkadaba 50:d84305e5e1c0 471 * Applicable only when operatingMode is ADMW1001_OPERATING_MODE_CONTINUOUS
Vkadaba 34:b60ee1e0af2b 472 */
Vkadaba 8:2f2775c34640 473 uint32_t cycleInterval;
Vkadaba 8:2f2775c34640 474 /*!< Cycle interval - specifies the time interval between the start of each
Vkadaba 8:2f2775c34640 475 * successive measurement cycle. Applicable only when operatingMode is
Vkadaba 8:2f2775c34640 476 * not ADMW1001_OPERATING_MODE_SINGLECYCLE
Vkadaba 8:2f2775c34640 477 */
Vkadaba 8:2f2775c34640 478 bool vBiasEnable;
Vkadaba 8:2f2775c34640 479 /*!< Enable voltage Bias output of ADC
Vkadaba 8:2f2775c34640 480 */
Vkadaba 8:2f2775c34640 481 float32_t externalRef1Value;
Vkadaba 8:2f2775c34640 482 /*!< Voltage value connected to external reference input #1.
Vkadaba 5:0728bde67bdb 483 * Applicable only if the selected reference type is
Vkadaba 8:2f2775c34640 484 * voltage.
Vkadaba 5:0728bde67bdb 485 * (see @ref ADMW1001_ADC_REFERENCE_TYPE)
Vkadaba 34:b60ee1e0af2b 486 */
Vkadaba 33:df7a00f1b8e1 487 float32_t RSenseValue;
Vkadaba 34:b60ee1e0af2b 488 /*!< Sense resistor value in Ohms. */
Vkadaba 34:b60ee1e0af2b 489 float32_t externalRefVoltage;
Vkadaba 34:b60ee1e0af2b 490 /*!< External Reference Voltage.
Vkadaba 34:b60ee1e0af2b 491 */
Vkadaba 45:f5f553b8c0d5 492 float32_t AVDDVoltage;
Vkadaba 45:f5f553b8c0d5 493 /*!< AVDD Voltage.
Vkadaba 45:f5f553b8c0d5 494 */
Vkadaba 45:f5f553b8c0d5 495 uint32_t reserved1[1];
Vkadaba 45:f5f553b8c0d5 496 /*!< Reserved for future use and ensure word alignment.
Vkadaba 45:f5f553b8c0d5 497 */
Vkadaba 8:2f2775c34640 498
Vkadaba 8:2f2775c34640 499 } ADMW1001_MEASUREMENT_CONFIG;
Vkadaba 5:0728bde67bdb 500
Vkadaba 5:0728bde67bdb 501 /*! ADMW1001 ADC Excitation Current output configuration
Vkadaba 5:0728bde67bdb 502 *
Vkadaba 5:0728bde67bdb 503 * @note applicable only to ADC analog sensor channels, and
Vkadaba 5:0728bde67bdb 504 * specific sensor types
Vkadaba 5:0728bde67bdb 505 */
Vkadaba 45:f5f553b8c0d5 506 typedef struct
Vkadaba 45:f5f553b8c0d5 507 {
Vkadaba 5:0728bde67bdb 508 ADMW1001_ADC_EXC_CURRENT outputLevel;
Vkadaba 5:0728bde67bdb 509 /*!< Excitation current output level */
Vkadaba 5:0728bde67bdb 510 ADMW1001_ADC_EXC_CURRENT_DIODE_RATIO diodeRatio;
Vkadaba 5:0728bde67bdb 511 /*!< Excitation current output diode ratio */
Vkadaba 45:f5f553b8c0d5 512 float32_t idealityRatio;
Vkadaba 8:2f2775c34640 513
Vkadaba 8:2f2775c34640 514 } ADMW1001_ADC_EXC_CURRENT_CONFIG;
Vkadaba 5:0728bde67bdb 515
Vkadaba 5:0728bde67bdb 516 /*! ADMW1001 ADC Filter configuration
Vkadaba 5:0728bde67bdb 517 *
Vkadaba 5:0728bde67bdb 518 * @note applicable only to ADC analog sensor channels
Vkadaba 5:0728bde67bdb 519 */
Vkadaba 45:f5f553b8c0d5 520 typedef struct
Vkadaba 45:f5f553b8c0d5 521 {
Vkadaba 8:2f2775c34640 522 ADMW1001_ADC_FILTER_TYPE type;
Vkadaba 5:0728bde67bdb 523 /*!< Filter type selection */
Vkadaba 8:2f2775c34640 524 ADMW1001_SINC_FILTER_RANGE sf;
Vkadaba 8:2f2775c34640 525 /*!< SF value used along with filter type and chop mode to determine speed */
Vkadaba 17:2f0028880874 526 ADMW1001_CHOP_MD chopMode;
Vkadaba 6:9d393a9677f4 527 /*!< Enable filter chop */
Vkadaba 8:2f2775c34640 528 bool notch1p2;
Vkadaba 6:9d393a9677f4 529 /*!< Enable Notch 2 Filter Mode */
Vkadaba 45:f5f553b8c0d5 530
Vkadaba 8:2f2775c34640 531 } ADMW1001_ADC_FILTER_CONFIG;
Vkadaba 5:0728bde67bdb 532
Vkadaba 5:0728bde67bdb 533 /*! ADMW1001 ADC analog channel configuration details
Vkadaba 5:0728bde67bdb 534 *
Vkadaba 5:0728bde67bdb 535 * @note applicable only to ADC analog sensor channels
Vkadaba 5:0728bde67bdb 536 */
Vkadaba 45:f5f553b8c0d5 537 typedef struct
Vkadaba 45:f5f553b8c0d5 538 {
Vkadaba 5:0728bde67bdb 539 ADMW1001_ADC_SENSOR_TYPE sensor;
Vkadaba 5:0728bde67bdb 540 /*!< Sensor type selection */
Vkadaba 6:9d393a9677f4 541 ADMW1001_ADC_RTD_CURVE rtdCurve;
Vkadaba 6:9d393a9677f4 542 /*!< Rtd curve selection */
Vkadaba 5:0728bde67bdb 543 ADMW1001_ADC_GAIN gain;
Vkadaba 5:0728bde67bdb 544 /*!< ADC Gain selection */
Vkadaba 5:0728bde67bdb 545 ADMW1001_ADC_EXC_CURRENT_CONFIG current;
Vkadaba 5:0728bde67bdb 546 /*!< ADC Excitation Current configuration */
Vkadaba 5:0728bde67bdb 547 ADMW1001_ADC_FILTER_CONFIG filter;
Vkadaba 5:0728bde67bdb 548 /*!< ADC Filter configuration */
Vkadaba 8:2f2775c34640 549 ADMW1001_ADC_REFERENCE_TYPE reference;
Vkadaba 5:0728bde67bdb 550 /*!< ADC Reference configuration */
Vkadaba 33:df7a00f1b8e1 551 uint8_t bufferBypass;
Vkadaba 45:f5f553b8c0d5 552 /*!< Buffer Bypass configuration */
Vkadaba 33:df7a00f1b8e1 553 uint8_t reserved0[2];
Vkadaba 8:2f2775c34640 554 /*!< Reserved for future use and ensure word alignment. */
Vkadaba 8:2f2775c34640 555 uint32_t reserved1[6];
Vkadaba 8:2f2775c34640 556 /*!< Reserved for future use and ensure word alignment. */
Vkadaba 8:2f2775c34640 557
Vkadaba 8:2f2775c34640 558 } ADMW1001_ADC_CHANNEL_CONFIG;
Vkadaba 8:2f2775c34640 559
Vkadaba 8:2f2775c34640 560 /*! ADMW1001 look-up table selection
Vkadaba 8:2f2775c34640 561 * Select table used to linearise the measurement.
Vkadaba 8:2f2775c34640 562 */
Vkadaba 45:f5f553b8c0d5 563 typedef enum
Vkadaba 45:f5f553b8c0d5 564 {
Vkadaba 8:2f2775c34640 565 ADMW1001_LUT_DEFAULT = 0,
Vkadaba 8:2f2775c34640 566 /*!< Default LUT */
Vkadaba 45:f5f553b8c0d5 567 ADMW1001_LUT_CUSTOM = 1,
Vkadaba 8:2f2775c34640 568 /*!< User defined custom LUT */
Vkadaba 45:f5f553b8c0d5 569 ADMW1001_LUT_RESERVED = 2,
Vkadaba 8:2f2775c34640 570 /*!< Reserved for future use */
Vkadaba 34:b60ee1e0af2b 571
Vkadaba 8:2f2775c34640 572 } ADMW1001_LUT_SELECT;
Vkadaba 5:0728bde67bdb 573
Vkadaba 5:0728bde67bdb 574 /*! ADMW1001 digital sensor data encoding
Vkadaba 5:0728bde67bdb 575 *
Vkadaba 5:0728bde67bdb 576 * @note applicable only to SPI and I2C digital sensor channels
Vkadaba 5:0728bde67bdb 577 */
Vkadaba 45:f5f553b8c0d5 578 typedef enum
Vkadaba 45:f5f553b8c0d5 579 {
Vkadaba 8:2f2775c34640 580 ADMW1001_DIGITAL_SENSOR_DATA_CODING_NONE = 0,
Vkadaba 5:0728bde67bdb 581 /**< None/Invalid - data format is ignored if coding is set to this value */
Vkadaba 5:0728bde67bdb 582 ADMW1001_DIGITAL_SENSOR_DATA_CODING_UNIPOLAR,
Vkadaba 5:0728bde67bdb 583 /**< Unipolar - unsigned integer values */
Vkadaba 5:0728bde67bdb 584 ADMW1001_DIGITAL_SENSOR_DATA_CODING_TWOS_COMPLEMENT,
Vkadaba 5:0728bde67bdb 585 /**< Twos-complement - signed integer values */
Vkadaba 5:0728bde67bdb 586 ADMW1001_DIGITAL_SENSOR_DATA_CODING_OFFSET_BINARY,
Vkadaba 5:0728bde67bdb 587 /**< Offset Binary - used to represent signed values with unsigned integers,
Vkadaba 5:0728bde67bdb 588 * with the mid-range value representing 0 */
Vkadaba 8:2f2775c34640 589
Vkadaba 8:2f2775c34640 590 } ADMW1001_DIGITAL_SENSOR_DATA_CODING;
Vkadaba 5:0728bde67bdb 591
Vkadaba 5:0728bde67bdb 592 /*! ADMW1001 digital sensor data format configuration
Vkadaba 5:0728bde67bdb 593 *
Vkadaba 5:0728bde67bdb 594 * @note applicable only to SPI and I2C digital sensor channels
Vkadaba 5:0728bde67bdb 595 */
Vkadaba 45:f5f553b8c0d5 596 typedef struct
Vkadaba 45:f5f553b8c0d5 597 {
Vkadaba 5:0728bde67bdb 598 ADMW1001_DIGITAL_SENSOR_DATA_CODING coding;
Vkadaba 5:0728bde67bdb 599 /**< Data Encoding of Sensor Result */
Vkadaba 5:0728bde67bdb 600 bool littleEndian;
Vkadaba 5:0728bde67bdb 601 /**< Set as true if data format is little-endian, false otherwise */
Vkadaba 5:0728bde67bdb 602 bool leftJustified;
Vkadaba 5:0728bde67bdb 603 /**< Set as true if data is left-justified in the data frame, false otherwise */
Vkadaba 5:0728bde67bdb 604 uint8_t frameLength;
Vkadaba 5:0728bde67bdb 605 /**< Data frame length (number of bytes to read from the sensor) */
Vkadaba 5:0728bde67bdb 606 uint8_t numDataBits;
Vkadaba 5:0728bde67bdb 607 /**< Number of relevant data bits to extract from the data frame */
Vkadaba 5:0728bde67bdb 608 uint8_t bitOffset;
Vkadaba 5:0728bde67bdb 609 /**< Data bit offset, relative to data alignment within the data frame */
Vkadaba 8:2f2775c34640 610 uint8_t reserved[2];
Vkadaba 8:2f2775c34640 611 /*!< Reserved for future use and ensure word alignment. */
Vkadaba 8:2f2775c34640 612
Vkadaba 8:2f2775c34640 613 } ADMW1001_DIGITAL_SENSOR_DATA_FORMAT;
Vkadaba 5:0728bde67bdb 614
Vkadaba 5:0728bde67bdb 615 /*! ADMW1001 digital sensor command
Vkadaba 5:0728bde67bdb 616 *
Vkadaba 5:0728bde67bdb 617 * @note applicable only to SPI and I2C digital sensor channels
Vkadaba 5:0728bde67bdb 618 */
Vkadaba 45:f5f553b8c0d5 619 typedef struct
Vkadaba 45:f5f553b8c0d5 620 {
Vkadaba 5:0728bde67bdb 621 uint8_t command[ADMW1001_SENSOR_COMMAND_MAX_LENGTH];
Vkadaba 5:0728bde67bdb 622 /*!< Optional command bytes to send to the device */
Vkadaba 5:0728bde67bdb 623 uint8_t commandLength;
Vkadaba 5:0728bde67bdb 624 /*!< Number of valid command bytes. Set to 0 if unused */
Vkadaba 8:2f2775c34640 625
Vkadaba 8:2f2775c34640 626 } ADMW1001_DIGITAL_SENSOR_COMMAND;
Vkadaba 5:0728bde67bdb 627
Vkadaba 5:0728bde67bdb 628 /*! ADMW1001 digital sensor calibration param
Vkadaba 5:0728bde67bdb 629 *
Vkadaba 5:0728bde67bdb 630 * @note applicable only to digital sensor channels
Vkadaba 5:0728bde67bdb 631 */
Vkadaba 45:f5f553b8c0d5 632 typedef struct
Vkadaba 45:f5f553b8c0d5 633 {
Vkadaba 5:0728bde67bdb 634 uint32_t calibrationParam;
Vkadaba 5:0728bde67bdb 635 /*!< Independently established environmental variable used during calibration
Vkadaba 5:0728bde67bdb 636 * of a digital sensor. Used only if the sensor supports calibration
Vkadaba 5:0728bde67bdb 637 * and expects an environmental parameter
Vkadaba 5:0728bde67bdb 638 */
Vkadaba 5:0728bde67bdb 639 bool enableCalibrationParam;
Vkadaba 5:0728bde67bdb 640 /*!< Allow Calibration_Parameter to be used during calibration of any digital sensor */
Vkadaba 8:2f2775c34640 641 uint8_t reserved[3];
Vkadaba 8:2f2775c34640 642 /*!< Reserved for future use and ensure word alignment. */
Vkadaba 8:2f2775c34640 643
Vkadaba 8:2f2775c34640 644 } ADMW1001_DIGITAL_CALIBRATION_COMMAND;
Vkadaba 5:0728bde67bdb 645
Vkadaba 5:0728bde67bdb 646 /*! ADMW1001 digital sensor communication config
Vkadaba 5:0728bde67bdb 647 *
Vkadaba 5:0728bde67bdb 648 * @note applicable only to digital sensor channels
Vkadaba 5:0728bde67bdb 649 */
Vkadaba 45:f5f553b8c0d5 650 typedef struct
Vkadaba 45:f5f553b8c0d5 651 {
Vkadaba 8:2f2775c34640 652 bool useCustomCommsConfig;
Vkadaba 5:0728bde67bdb 653 /*!< Optional parameter to enable user digital communication settings */
Vkadaba 8:2f2775c34640 654 ADMW1001_DIGITAL_SENSOR_COMMS_I2C_CLOCK_SPEED i2cClockSpeed;
Vkadaba 5:0728bde67bdb 655 /*!< Optional parameter to configure specific i2c speed for i2c sensor */
Vkadaba 8:2f2775c34640 656 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_MODE spiMode;
Vkadaba 5:0728bde67bdb 657 /*!< Optional parameter to configure specific spi mode for spi sensor */
Vkadaba 8:2f2775c34640 658 ADMW1001_DIGITAL_SENSOR_COMMS_SPI_CLOCK spiClock;
Vkadaba 5:0728bde67bdb 659 /*!< Optional parameter to configure specific spi clock for spi sensor */
Vkadaba 8:2f2775c34640 660
Vkadaba 8:2f2775c34640 661 } ADMW1001_DIGITAL_SENSOR_COMMS;
Vkadaba 5:0728bde67bdb 662
Vkadaba 5:0728bde67bdb 663 /*! ADMW1001 I2C digital channel configuration details
Vkadaba 5:0728bde67bdb 664 *
Vkadaba 5:0728bde67bdb 665 * @note applicable only to I2C digital sensor channels
Vkadaba 5:0728bde67bdb 666 */
Vkadaba 45:f5f553b8c0d5 667 typedef struct
Vkadaba 45:f5f553b8c0d5 668 {
Vkadaba 8:2f2775c34640 669 ADMW1001_I2C_SENSOR_TYPE sensor;
Vkadaba 5:0728bde67bdb 670 /*!< Sensor type selection */
Vkadaba 8:2f2775c34640 671 uint8_t deviceAddress;
Vkadaba 5:0728bde67bdb 672 /*!< I2C device address (7-bit) */
Vkadaba 8:2f2775c34640 673 uint8_t reserved;
Vkadaba 8:2f2775c34640 674 /*!< Reserved for future use and ensure word alignment. */
Vkadaba 8:2f2775c34640 675 ADMW1001_DIGITAL_SENSOR_COMMAND configurationCommand;
Vkadaba 5:0728bde67bdb 676 /*!< Optional configuration command to send to the device at start-up.
Vkadaba 5:0728bde67bdb 677 * A default configuration command will be used if this is not specified.
Vkadaba 5:0728bde67bdb 678 * Applicable only to specific I2C sensor types.
Vkadaba 5:0728bde67bdb 679 */
Vkadaba 8:2f2775c34640 680 ADMW1001_DIGITAL_SENSOR_COMMAND dataRequestCommand;
Vkadaba 5:0728bde67bdb 681 /*!< Optional data request command to send to the device for each sample.
Vkadaba 5:0728bde67bdb 682 * A default data request command will be used if this is not specified.
Vkadaba 5:0728bde67bdb 683 * Applicable only to specific I2C sensor types.
Vkadaba 5:0728bde67bdb 684 */
Vkadaba 8:2f2775c34640 685 ADMW1001_DIGITAL_SENSOR_DATA_FORMAT dataFormat;
Vkadaba 5:0728bde67bdb 686 /*!< Optional data format configuration to parse/extract data from the device.
Vkadaba 5:0728bde67bdb 687 * A default data format will be used if this is not specified.
Vkadaba 5:0728bde67bdb 688 * Applicable only to specific I2C sensor types
Vkadaba 5:0728bde67bdb 689 */
Vkadaba 8:2f2775c34640 690 ADMW1001_DIGITAL_CALIBRATION_COMMAND digitalCalibrationParam;
Vkadaba 5:0728bde67bdb 691 /*!< This is used to supply an independently established environmental variable
Vkadaba 5:0728bde67bdb 692 * that must be used during calibration of a [digital] sensor which a)
Vkadaba 5:0728bde67bdb 693 * supports calibration and b) expects an environmental parameter.
Vkadaba 5:0728bde67bdb 694 * An example is a CO2 sensor, which may require the CO2 concentration level
Vkadaba 5:0728bde67bdb 695 * when performing a calibration
Vkadaba 5:0728bde67bdb 696 */
Vkadaba 8:2f2775c34640 697 ADMW1001_DIGITAL_SENSOR_COMMS configureComms;
Vkadaba 5:0728bde67bdb 698 /*!< Optional configuration to setup a user communication config.
Vkadaba 5:0728bde67bdb 699 * A default configuration will be used if this is not specified.
Vkadaba 5:0728bde67bdb 700 * Applicable only to specific I2C sensor types.
Vkadaba 5:0728bde67bdb 701 */
Vkadaba 8:2f2775c34640 702
Vkadaba 8:2f2775c34640 703 } ADMW1001_I2C_CHANNEL_CONFIG;
Vkadaba 5:0728bde67bdb 704
Vkadaba 5:0728bde67bdb 705 /*! ADMW1001 SPI digital channel configuration details
Vkadaba 5:0728bde67bdb 706 *
Vkadaba 5:0728bde67bdb 707 * @note applicable only to SPI digital sensor channels
Vkadaba 5:0728bde67bdb 708 */
Vkadaba 45:f5f553b8c0d5 709 typedef struct
Vkadaba 45:f5f553b8c0d5 710 {
Vkadaba 5:0728bde67bdb 711 ADMW1001_SPI_SENSOR_TYPE sensor;
Vkadaba 5:0728bde67bdb 712 /*!< Sensor type selection */
Vkadaba 8:2f2775c34640 713 uint8_t reserved[2];
Vkadaba 34:b60ee1e0af2b 714 /*!< Reserved for future use and ensure word alignment. */
Vkadaba 5:0728bde67bdb 715 ADMW1001_DIGITAL_SENSOR_COMMAND configurationCommand;
Vkadaba 5:0728bde67bdb 716 /*!< Optional configuration command to send to the device at start-up.
Vkadaba 5:0728bde67bdb 717 * A default configuration command will be used if this is not specified.
Vkadaba 5:0728bde67bdb 718 * Applicable only to specific SPI sensor types.
Vkadaba 5:0728bde67bdb 719 */
Vkadaba 5:0728bde67bdb 720 ADMW1001_DIGITAL_SENSOR_COMMAND dataRequestCommand;
Vkadaba 5:0728bde67bdb 721 /*!< Optional data request command to send to the device for each sample.
Vkadaba 5:0728bde67bdb 722 * A default data request command will be used if this is not specified.
Vkadaba 5:0728bde67bdb 723 * Applicable only to specific SPI sensor types.
Vkadaba 5:0728bde67bdb 724 */
Vkadaba 5:0728bde67bdb 725 ADMW1001_DIGITAL_SENSOR_DATA_FORMAT dataFormat;
Vkadaba 5:0728bde67bdb 726 /*!< Optional data format configuration to parse/extract data from the device.
Vkadaba 5:0728bde67bdb 727 * A default data format will be used if this is not specified.
Vkadaba 5:0728bde67bdb 728 * Applicable only to specific SPI sensor types
Vkadaba 5:0728bde67bdb 729 */
Vkadaba 5:0728bde67bdb 730 ADMW1001_DIGITAL_CALIBRATION_COMMAND digitalCalibrationParam;
Vkadaba 5:0728bde67bdb 731 /*!< This is used to supply an independently established environmental variable
Vkadaba 5:0728bde67bdb 732 * that must be used during calibration of a [digital] sensor which a)
Vkadaba 5:0728bde67bdb 733 * supports calibration and b) expects an environmental parameter.
Vkadaba 5:0728bde67bdb 734 * An example is a CO2 sensor, which may require the CO2 concentration level
Vkadaba 5:0728bde67bdb 735 * when performing a calibration
Vkadaba 5:0728bde67bdb 736 */
Vkadaba 8:2f2775c34640 737 ADMW1001_DIGITAL_SENSOR_COMMS configureComms;
Vkadaba 5:0728bde67bdb 738 /*!< Optional configuration to setup a user communication config.
Vkadaba 5:0728bde67bdb 739 * A default configuration will be used if this is not specified.
Vkadaba 5:0728bde67bdb 740 * Applicable only to specific SPI sensor types.
Vkadaba 5:0728bde67bdb 741 */
Vkadaba 5:0728bde67bdb 742
Vkadaba 8:2f2775c34640 743 } ADMW1001_SPI_CHANNEL_CONFIG;
Vkadaba 5:0728bde67bdb 744
Vkadaba 5:0728bde67bdb 745 /*! ADMW1001 Measurement Channel configuration details */
Vkadaba 45:f5f553b8c0d5 746 typedef struct
Vkadaba 45:f5f553b8c0d5 747 {
Vkadaba 8:2f2775c34640 748 bool enableChannel;
Vkadaba 5:0728bde67bdb 749 /*!< Option to include this channel in normal measurement cycles */
Vkadaba 8:2f2775c34640 750 bool disablePublishing;
Vkadaba 5:0728bde67bdb 751 /*!< Option to disable publishing of data samples from this channel. The
Vkadaba 5:0728bde67bdb 752 * channel may still be included in measurement cycles, but data samples
Vkadaba 5:0728bde67bdb 753 * obtained from this channel will not be published. This is typically
Vkadaba 5:0728bde67bdb 754 * used for channels which are required only as a compensation reference
Vkadaba 5:0728bde67bdb 755 * for another channel (e.g. Cold-Junction Compensation channels).
Vkadaba 5:0728bde67bdb 756 */
Vkadaba 8:2f2775c34640 757 ADMW1001_CH_ID compensationChannel;
Vkadaba 8:2f2775c34640 758 /*!< Optional compensation channel. Set to ADMW1001_CH_ID_NONE if not
Vkadaba 5:0728bde67bdb 759 * required. Typically used for thermocouple sensors that require a
Vkadaba 5:0728bde67bdb 760 * separate measurement of the "cold-junction" temperature, which can be
Vkadaba 5:0728bde67bdb 761 * be provided by an RTD temperature sensor connected on a separate
Vkadaba 5:0728bde67bdb 762 * "compensation channel" */
Vkadaba 8:2f2775c34640 763 ADMW1001_LUT_SELECT lutSelect;
Vkadaba 8:2f2775c34640 764 /*!<Select Look Up Table LUT for calculations, this implies that the
Vkadaba 5:0728bde67bdb 765 * fundamental measurement for the sensor (typically mV or Ohms)
Vkadaba 8:2f2775c34640 766 * 0 = default, 1= unity, 2 = custom
Vkadaba 5:0728bde67bdb 767 */
Vkadaba 8:2f2775c34640 768 ADMW1001_MEASUREMENT_UNIT measurementUnit;
Vkadaba 5:0728bde67bdb 769 /*!< Optional measurement unit selection for conversion results. Applicable
Vkadaba 5:0728bde67bdb 770 * only for certain sensor types. Set to
Vkadaba 5:0728bde67bdb 771 * ADMW1001_MEASUREMENT_UNIT_DEFAULT if not applicable.
Vkadaba 5:0728bde67bdb 772 */
Vkadaba 8:2f2775c34640 773 float32_t lowThreshold;
Vkadaba 5:0728bde67bdb 774 /*!< Optional minimum threshold value for each processed sample, to be
Vkadaba 5:0728bde67bdb 775 * checked prior to publishing. A channel ALERT condition is raised
Vkadaba 5:0728bde67bdb 776 * if the processed value is lower than this threshold. Set to NaN
Vkadaba 5:0728bde67bdb 777 * if not required.
Vkadaba 5:0728bde67bdb 778 */
Vkadaba 8:2f2775c34640 779 float32_t highThreshold;
Vkadaba 5:0728bde67bdb 780 /*!< Optional maximum threshold value for each processed sample, to be
Vkadaba 5:0728bde67bdb 781 * checked prior to publishing. A channel ALERT condition is raised
Vkadaba 5:0728bde67bdb 782 * if the processed value is higher than this threshold. Set to NaN
Vkadaba 5:0728bde67bdb 783 * if not required.
Vkadaba 5:0728bde67bdb 784 */
Vkadaba 8:2f2775c34640 785 float32_t offsetAdjustment;
Vkadaba 5:0728bde67bdb 786 /*!< Optional offset adjustment value applied to each processed sample.
Vkadaba 5:0728bde67bdb 787 * Set to NaN or 0.0 if not required.
Vkadaba 5:0728bde67bdb 788 */
Vkadaba 8:2f2775c34640 789 float32_t gainAdjustment;
Vkadaba 5:0728bde67bdb 790 /*!< Optional gain adjustment value applied to each processed sample.
Vkadaba 5:0728bde67bdb 791 * Set to NaN or 1.0 if not required.
Vkadaba 5:0728bde67bdb 792 */
Vkadaba 8:2f2775c34640 793 float32_t sensorParameter;
Vkadaba 5:0728bde67bdb 794 /*!< Optional sensor parameter adjustment.
Vkadaba 5:0728bde67bdb 795 * Set to NaN or 0 if not required.
Vkadaba 5:0728bde67bdb 796 */
Vkadaba 8:2f2775c34640 797 uint32_t measurementsPerCycle;
Vkadaba 5:0728bde67bdb 798 /*!< The number of measurements to obtain from this channel within each
Vkadaba 5:0728bde67bdb 799 * cycle. Each enabled channel is measured in turn, until the number of
Vkadaba 5:0728bde67bdb 800 * measurements requested for the channel has been reached. A different
Vkadaba 5:0728bde67bdb 801 * number of measurements-per-cycle may be specified for each channel.
Vkadaba 5:0728bde67bdb 802 */
Vkadaba 8:2f2775c34640 803 uint32_t cycleSkipCount;
Vkadaba 5:0728bde67bdb 804 /*!< Optional number of cycles to skip, such that this channel is included
Vkadaba 5:0728bde67bdb 805 * in the sequence in only one of every (cycleSkipCount + 1) cycles that
Vkadaba 5:0728bde67bdb 806 * occur. If set to 0 (default), this channel is included in every cycle;
Vkadaba 5:0728bde67bdb 807 * if set to 1, this channel is included in every 2nd cycle; if set to 2,
Vkadaba 5:0728bde67bdb 808 * this channel is included in every 3rd cycle, and so on.
Vkadaba 5:0728bde67bdb 809 */
Vkadaba 8:2f2775c34640 810 uint32_t extraSettlingTime;
Vkadaba 5:0728bde67bdb 811 /*!< A minimum settling time is applied internally for each channel, based
Vkadaba 45:f5f553b8c0d5 812 * on the sensor type. However, additional settling time (milliseconds)
Vkadaba 5:0728bde67bdb 813 * can optionally be specified. Set to 0 if not required.
Vkadaba 5:0728bde67bdb 814 */
Vkadaba 8:2f2775c34640 815 ADMW1001_CHANNEL_PRIORITY priority;
Vkadaba 5:0728bde67bdb 816 /*!< By default, channels are arranged in the measurement sequence based on
Vkadaba 5:0728bde67bdb 817 * ascending order of channel ID. However, a priority-level may be
Vkadaba 5:0728bde67bdb 818 * specified per channel to force a different ordering of the channels,
Vkadaba 5:0728bde67bdb 819 * with higher-priority channels appearing before lower-priority channels.
Vkadaba 5:0728bde67bdb 820 * Channels with equal priority are ordered by ascending order of channel
Vkadaba 5:0728bde67bdb 821 * ID. Lower numbers indicate higher priority, with 0 being the highest.
Vkadaba 5:0728bde67bdb 822 * Set to 0 if not required.
Vkadaba 5:0728bde67bdb 823 */
Vkadaba 45:f5f553b8c0d5 824 union
Vkadaba 45:f5f553b8c0d5 825 {
Vkadaba 8:2f2775c34640 826 ADMW1001_ADC_CHANNEL_CONFIG adcChannelConfig;
Vkadaba 5:0728bde67bdb 827 /*!< ADC channel configuration - applicable only to ADC channels */
Vkadaba 8:2f2775c34640 828 ADMW1001_I2C_CHANNEL_CONFIG i2cChannelConfig;
Vkadaba 5:0728bde67bdb 829 /*!< I2C channel configuration - applicable only to I2C channels */
Vkadaba 8:2f2775c34640 830 ADMW1001_SPI_CHANNEL_CONFIG spiChannelConfig;
Vkadaba 5:0728bde67bdb 831 /*!< SPI channel configuration - applicable only to SPI channels */
Vkadaba 5:0728bde67bdb 832 };
Vkadaba 6:9d393a9677f4 833 /*!< Only one of adcChannelConfig, i2cChannelConfig, spiChannelConfig
Vkadaba 6:9d393a9677f4 834 * is required, depending on the channel designation
Vkadaba 6:9d393a9677f4 835 * (analog, I2C, SPI)
Vkadaba 5:0728bde67bdb 836 */
Vkadaba 8:2f2775c34640 837
Vkadaba 8:2f2775c34640 838 } ADMW1001_CHANNEL_CONFIG;
Vkadaba 5:0728bde67bdb 839
Vkadaba 5:0728bde67bdb 840 /*! ADMW1001 Diagnostics configuration details */
Vkadaba 45:f5f553b8c0d5 841 typedef struct
Vkadaba 45:f5f553b8c0d5 842 {
Vkadaba 8:2f2775c34640 843 bool disableGlobalDiag;
Vkadaba 5:0728bde67bdb 844 /*!< Option to disable the following diagnostic checks on the ADC:
Vkadaba 5:0728bde67bdb 845 * - Reference Detection errors
Vkadaba 5:0728bde67bdb 846 * - Input under-/over-voltage errors
Vkadaba 5:0728bde67bdb 847 * - Calibration, Conversion and Saturation errors
Vkadaba 5:0728bde67bdb 848 */
Vkadaba 8:2f2775c34640 849 bool disableMeasurementDiag;
Vkadaba 5:0728bde67bdb 850 /*!< Option to disable additional checks per measurement channel:
Vkadaba 5:0728bde67bdb 851 * - High/low threshold limit violation
Vkadaba 5:0728bde67bdb 852 */
Vkadaba 8:2f2775c34640 853
Vkadaba 8:2f2775c34640 854 bool disableCriticalTempAbort;
Vkadaba 5:0728bde67bdb 855 /*!< Option to disable abort of measurement cycle if the operating
Vkadaba 5:0728bde67bdb 856 * temperature of the ADMW1001 has exceeded critical limits
Vkadaba 5:0728bde67bdb 857 */
Vkadaba 8:2f2775c34640 858
Vkadaba 45:f5f553b8c0d5 859 uint8_t osdFrequency;
Vkadaba 5:0728bde67bdb 860 /*!< Option to enable Open-Circuit Detection at a selected cycle interval */
Vkadaba 5:0728bde67bdb 861
Vkadaba 8:2f2775c34640 862 } ADMW1001_DIAGNOSTICS_CONFIG;
Vkadaba 8:2f2775c34640 863
Vkadaba 5:0728bde67bdb 864 typedef uint16_t ADMW1001_ADVANCED_ACCESS_KEY;
Vkadaba 5:0728bde67bdb 865
Vkadaba 5:0728bde67bdb 866 /*! ADMW1001 Device configuration details */
Vkadaba 45:f5f553b8c0d5 867 typedef struct
Vkadaba 45:f5f553b8c0d5 868 {
Vkadaba 5:0728bde67bdb 869 ADMW1001_POWER_CONFIG power;
Vkadaba 5:0728bde67bdb 870 /*!< Power configuration details */
Vkadaba 5:0728bde67bdb 871 ADMW1001_MEASUREMENT_CONFIG measurement;
Vkadaba 5:0728bde67bdb 872 /*!< Measurement configuration details */
Vkadaba 5:0728bde67bdb 873 ADMW1001_DIAGNOSTICS_CONFIG diagnostics;
Vkadaba 5:0728bde67bdb 874 /*!< FFT configuration details */
Vkadaba 5:0728bde67bdb 875 ADMW1001_CHANNEL_CONFIG channels[ADMW1001_MAX_CHANNELS];
Vkadaba 5:0728bde67bdb 876 /*!< Channel-specific configuration details */
Vkadaba 5:0728bde67bdb 877 ADMW1001_ADVANCED_ACCESS_KEY advancedAccessKey;
Vkadaba 5:0728bde67bdb 878 /*!< Key to enable access to advanced sensor configuration options */
Vkadaba 8:2f2775c34640 879
Vkadaba 8:2f2775c34640 880 } ADMW1001_CONFIG;
Vkadaba 5:0728bde67bdb 881
Vkadaba 5:0728bde67bdb 882 #ifdef __cplusplus
Vkadaba 5:0728bde67bdb 883 }
Vkadaba 5:0728bde67bdb 884 #endif
Vkadaba 5:0728bde67bdb 885
Vkadaba 5:0728bde67bdb 886 /*!
Vkadaba 5:0728bde67bdb 887 * @}
Vkadaba 5:0728bde67bdb 888 */
Vkadaba 5:0728bde67bdb 889
Vkadaba 5:0728bde67bdb 890 #endif /* __ADMW1001_CONFIG_H__ */