TextLCD_Config.h

00001 /* mbed TextLCD Library, for LCDs based on HD44780 controllers
00002  * Copyright (c) 2014, WH
00003  *               2014, v01: WH, Extracted from TextLCD.h as of v14
00004  *               2014, v02: WH, Added AC780 support, added I2C expander modules, fixed setBacklight() for inverted logic modules. Fixed bug in LCD_SPI_N define
00005  *               2014, v03: WH, Added LCD_SPI_N_3_8 define for ST7070
00006  *               2015, v04: WH, Added support for alternative fonttables (eg PCF21XX)
00007  *               2015, v05: WH, Clean up low-level _writeCommand() and _writeData(), Added support for alt fonttables (eg PCF21XX), Added ST7066_ACM for ACM1602 module, fixed contrast for ST7032 
00008  *
00009  * Permission is hereby granted, free of charge, to any person obtaining a copy
00010  * of this software and associated documentation files (the "Software"), to deal
00011  * in the Software without restriction, including without limitation the rights
00012  * to use, copy, modify, merge, publish, distribute, sublicense, and/or sell
00013  * copies of the Software, and to permit persons to whom the Software is
00014  * furnished to do so, subject to the following conditions:
00015  *
00016  * The above copyright notice and this permission notice shall be included in
00017  * all copies or substantial portions of the Software.
00018  *
00019  * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, EXPRESS OR
00020  * IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES OF MERCHANTABILITY,
00021  * FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT. IN NO EVENT SHALL THE
00022  * AUTHORS OR COPYRIGHT HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER
00023  * LIABILITY, WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING FROM,
00024  * OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR OTHER DEALINGS IN
00025  * THE SOFTWARE.
00026  */
00027 #ifndef MBED_TEXTLCDCONFIG_H
00028 #define MBED_TEXTLCDCONFIG_H
00029 
00030 //Select hardware interface options to reduce memory footprint (multiple options allowed)
00031 #define LCD_I2C        1           /* I2C Expander PCF8574/MCP23008 */
00032 #define LCD_SPI        1           /* SPI Expander SN74595          */
00033 #define LCD_I2C_N      1           /* Native I2C bus     */
00034 #define LCD_SPI_N      1           /* Native SPI bus     */
00035 #define LCD_SPI_N_3_8  1           /* Native SPI bus     */
00036 #define LCD_SPI_N_3_9  1           /* Native SPI bus     */
00037 #define LCD_SPI_N_3_10 1           /* Native SPI bus     */
00038 #define LCD_SPI_N_3_16 1           /* Native SPI bus     */
00039 #define LCD_SPI_N_3_24 1           /* Native SPI bus     */
00040 
00041 //Select options to reduce memory footprint (multiple options allowed)
00042 #define LCD_UDC        1           /* Enable predefined UDC example*/                
00043 #define LCD_PRINTF     1           /* Enable Stream implementation */                
00044 
00045 //Select option to activate default fonttable or alternatively use conversion for specific controller versions (eg PCF2119C)
00046 #define LCD_DEFAULT_FONT 1      
00047 
00048 //Pin Defines for I2C PCF8574/PCF8574A or MCP23008 and SPI 74595 bus expander interfaces
00049 //Different commercially available LCD portexpanders use different wiring conventions.
00050 //LCD and serial portexpanders should be wired according to the tables below.
00051 //
00052 //Select Serial Port Expander Hardware module (one option only)
00053 #define DEFAULT        0
00054 #define ADAFRUIT       0
00055 #define DFROBOT        0
00056 #define YWROBOT        1
00057 #define GYLCD          0
00058 #define SYDZ           0
00059 
00060 #if (DEFAULT==1)
00061 //Definitions for default (WH) mapping between serial port expander pins and LCD controller
00062 //This hardware supports the I2C bus expander (PCF8574/PCF8574A or MCP23008) and SPI bus expander (74595) interfaces
00063 //See https://mbed.org/cookbook/Text-LCD-Enhanced
00064 //
00065 //Note: LCD RW pin must be connected to GND
00066 //      E2 is used for LCD40x4 (second controller)
00067 //      BL may be used to control backlight
00068 #define D_LCD_PIN_D4   0
00069 #define D_LCD_PIN_D5   1
00070 #define D_LCD_PIN_D6   2
00071 #define D_LCD_PIN_D7   3
00072 #define D_LCD_PIN_RS   4
00073 #define D_LCD_PIN_E    5
00074 #define D_LCD_PIN_E2   6
00075 #define D_LCD_PIN_BL   7
00076 
00077 #define D_LCD_PIN_RW   D_LCD_PIN_E2
00078 
00079 //Select I2C Portexpander type (one option only)
00080 #define PCF8574        1
00081 #define MCP23008       0
00082 
00083 //Inverted Backlight control
00084 #define BACKLIGHT_INV  0
00085 #endif
00086 
00087 #if (ADAFRUIT==1)
00088 //Definitions for Adafruit i2cspilcdbackpack mapping between serial port expander pins and LCD controller
00089 //This hardware supports both an I2C expander (MCP23008) and an SPI expander (74595) selectable by a jumper.
00090 //Slaveaddress may be set by solderbridges (default 0x40). SDA/SCL has pullup Resistors onboard.
00091 //See http://www.ladyada.net/products/i2cspilcdbackpack
00092 //
00093 //Note: LCD RW pin must be kept LOW
00094 //      E2 is not available on this hardware and so it does not support LCD40x4 (second controller)
00095 //      BL is used to control backlight
00096 #define D_LCD_PIN_0    0
00097 #define D_LCD_PIN_RS   1
00098 #define D_LCD_PIN_E    2
00099 #define D_LCD_PIN_D4   3
00100 #define D_LCD_PIN_D5   4
00101 #define D_LCD_PIN_D6   5
00102 #define D_LCD_PIN_D7   6
00103 #define D_LCD_PIN_BL   7
00104 
00105 #define D_LCD_PIN_E2   D_LCD_PIN_0
00106 
00107 //Force I2C portexpander type
00108 #define PCF8574        0
00109 #define MCP23008       1
00110 
00111 //Inverted Backlight control
00112 #define BACKLIGHT_INV  0
00113 #endif
00114 
00115 #if (DFROBOT==1)
00116 //Definitions for DFROBOT LCD2004 Module mapping between serial port expander pins and LCD controller
00117 //This hardware uses PCF8574 and is different from earlier/different Arduino I2C LCD displays
00118 //Slaveaddress hardwired to 0x4E. SDA/SCL has pullup Resistors onboard.
00119 //See http://arduino-info.wikispaces.com/LCD-Blue-I2C
00120 //
00121 //Definitions for DFROBOT V1.1 
00122 //This hardware uses PCF8574. Slaveaddress may be set by jumpers (default 0x40).
00123 //SDA/SCL has pullup Resistors onboard and features a voltage level converter 3V3 <-> 5V.
00124 //See http://www.dfrobot.com/index.php?route=product/product&product_id=135
00125 //
00126 //
00127 //Note: LCD RW pin must be kept LOW
00128 //      E2 is not available on default Arduino hardware and so it does not support LCD40x4 (second controller)
00129 //      BL is used to control backlight
00130 #define D_LCD_PIN_RS   0
00131 #define D_LCD_PIN_RW   1
00132 #define D_LCD_PIN_E    2
00133 #define D_LCD_PIN_BL   3
00134 #define D_LCD_PIN_D4   4
00135 #define D_LCD_PIN_D5   5
00136 #define D_LCD_PIN_D6   6
00137 #define D_LCD_PIN_D7   7
00138 
00139 #define D_LCD_PIN_E2   D_LCD_PIN_RW
00140 
00141 //Force I2C portexpander type
00142 #define PCF8574        1
00143 #define MCP23008       0
00144 
00145 //Inverted Backlight control
00146 #define BACKLIGHT_INV  0
00147 #endif
00148 
00149 #if (YWROBOT==1)
00150 //Definitions for YWROBOT LCM1602 V1 Module mapping between serial port expander pins and LCD controller. 
00151 //Very similar to DFROBOT. This hardware uses PCF8574.
00152 //Slaveaddress may be set by solderbridges (default 0x4E). SDA/SCL has no pullup Resistors onboard.
00153 //See http://arduino-info.wikispaces.com/LCD-Blue-I2C
00154 //
00155 //Note: LCD RW pin must be kept LOW
00156 //      E2 is not available on default hardware and so it does not support LCD40x4 (second controller)
00157 //      BL is used to control backlight, reverse logic: Low turns on Backlight. This is handled in setBacklight()
00158 #define D_LCD_PIN_RS   0
00159 #define D_LCD_PIN_RW   1
00160 #define D_LCD_PIN_E    2
00161 #define D_LCD_PIN_BL   3
00162 #define D_LCD_PIN_D4   4
00163 #define D_LCD_PIN_D5   5
00164 #define D_LCD_PIN_D6   6
00165 #define D_LCD_PIN_D7   7
00166 
00167 #define D_LCD_PIN_E2   D_LCD_PIN_RW
00168 
00169 //Force I2C portexpander type
00170 #define PCF8574        1
00171 #define MCP23008       0
00172 
00173 //Inverted Backlight control
00174 #define BACKLIGHT_INV  0
00175 #endif
00176 
00177 #if (GYLCD==1)
00178 //Definitions for Arduino-IIC-LCD GY-LCD-V1 Module mapping between serial port expander pins and LCD controller. 
00179 //Very similar to DFROBOT. This hardware uses PCF8574.
00180 //Slaveaddress may be set by solderbridges (default 0x4E). SDA/SCL has pullup Resistors onboard.
00181 //See http://arduino-info.wikispaces.com/LCD-Blue-I2C
00182 //
00183 //Note: LCD RW pin must be kept LOW
00184 //      E2 is not available on default hardware and so it does not support LCD40x4 (second controller)
00185 //      BL is used to control backlight, reverse logic: Low turns on Backlight. This is handled in setBacklight()
00186 #define D_LCD_PIN_D4   0
00187 #define D_LCD_PIN_D5   1
00188 #define D_LCD_PIN_D6   2
00189 #define D_LCD_PIN_D7   3
00190 #define D_LCD_PIN_EN   4
00191 #define D_LCD_PIN_RW   5
00192 #define D_LCD_PIN_RS   6
00193 #define D_LCD_PIN_BL   7
00194 
00195 #define D_LCD_PIN_E2   D_LCD_PIN_RW
00196 
00197 //Force I2C portexpander type
00198 #define PCF8574        1
00199 #define MCP23008       0
00200 
00201 //Force Inverted Backlight control
00202 #define BACKLIGHT_INV  1
00203 #endif
00204 
00205 #if (SYDZ==1)
00206 //Definitions for SYDZ Module mapping between serial port expander pins and LCD controller. 
00207 //Very similar to DFROBOT. This hardware uses PCF8574A and uses inverted Backlight control
00208 //Slaveaddress may be set by switches (default 0x40). SDA/SCL has pullup Resistors onboard.
00209 //See ebay
00210 //
00211 //Note: LCD RW pin must be kept LOW
00212 //      E2 is not available on default hardware and so it does not support LCD40x4 (second controller)
00213 //      BL is used to control backlight, reverse logic: Low turns on Backlight. This is handled in setBacklight()
00214 #define D_LCD_PIN_RS   0
00215 #define D_LCD_PIN_RW   1
00216 #define D_LCD_PIN_E    2
00217 #define D_LCD_PIN_BL   3
00218 #define D_LCD_PIN_D4   4
00219 #define D_LCD_PIN_D5   5
00220 #define D_LCD_PIN_D6   6
00221 #define D_LCD_PIN_D7   7
00222 
00223 #define D_LCD_PIN_E2   D_LCD_PIN_RW
00224 
00225 //Force I2C portexpander type
00226 #define PCF8574        1
00227 #define MCP23008       0
00228 
00229 //Force Inverted Backlight control
00230 #define BACKLIGHT_INV  1
00231 #endif
00232 
00233 //Bitpattern Defines for I2C PCF8574/PCF8574A, MCP23008 and SPI 74595 Bus expanders
00234 //Don't change!
00235 //
00236 #define D_LCD_D4       (1<<D_LCD_PIN_D4)
00237 #define D_LCD_D5       (1<<D_LCD_PIN_D5)
00238 #define D_LCD_D6       (1<<D_LCD_PIN_D6)
00239 #define D_LCD_D7       (1<<D_LCD_PIN_D7)
00240 #define D_LCD_RS       (1<<D_LCD_PIN_RS)
00241 #define D_LCD_E        (1<<D_LCD_PIN_E)
00242 #define D_LCD_E2       (1<<D_LCD_PIN_E2)
00243 #define D_LCD_BL       (1<<D_LCD_PIN_BL)
00244 //#define D_LCD_RW       (1<<D_LCD_PIN_RW)
00245 
00246 #define D_LCD_BUS_MSK  (D_LCD_D4 | D_LCD_D5 | D_LCD_D6 | D_LCD_D7)
00247 #define D_LCD_BUS_DEF  0x00
00248 
00249 /* PCF8574/PCF8574A I2C portexpander slave address */
00250 #define PCF8574_SA0    0x40
00251 #define PCF8574_SA1    0x42
00252 #define PCF8574_SA2    0x44
00253 #define PCF8574_SA3    0x46
00254 #define PCF8574_SA4    0x48
00255 #define PCF8574_SA5    0x4A
00256 #define PCF8574_SA6    0x4C
00257 #define PCF8574_SA7    0x4E
00258 
00259 #define PCF8574A_SA0   0x70
00260 #define PCF8574A_SA1   0x72
00261 #define PCF8574A_SA2   0x74
00262 #define PCF8574A_SA3   0x76
00263 #define PCF8574A_SA4   0x78
00264 #define PCF8574A_SA5   0x7A
00265 #define PCF8574A_SA6   0x7C
00266 #define PCF8574A_SA7   0x7E
00267 
00268 /* MCP23008 I2C portexpander slave address */
00269 #define MCP23008_SA0   0x40
00270 #define MCP23008_SA1   0x42
00271 #define MCP23008_SA2   0x44
00272 #define MCP23008_SA3   0x46
00273 #define MCP23008_SA4   0x48
00274 #define MCP23008_SA5   0x4A
00275 #define MCP23008_SA6   0x4C
00276 #define MCP23008_SA7   0x4E
00277 
00278 /* MCP23008 I2C portexpander internal registers */
00279 #define IODIR          0x00
00280 #define IPOL           0x01
00281 #define GPINTEN        0x02
00282 #define DEFVAL         0x03
00283 #define INTCON         0x04
00284 #define IOCON          0x05
00285 #define GPPU           0x06
00286 #define INTF           0x07
00287 #define INTCAP         0x08
00288 #define GPIO           0x09
00289 #define OLAT           0x0A
00290 
00291 /* ST7032i I2C slave address */
00292 #define ST7032_SA      0x7C
00293 
00294 /* ST7036i I2C slave address */
00295 #define ST7036_SA0     0x78
00296 #define ST7036_SA1     0x7A
00297 #define ST7036_SA2     0x7C
00298 #define ST7036_SA3     0x7E
00299 
00300 /* ST7066_ACM I2C slave address, Added for ACM1602 module  */
00301 #define ST7066_SA0     0xA0
00302 
00303 /* PCF21XX I2C slave address */
00304 #define PCF21XX_SA0    0x74
00305 #define PCF21XX_SA1    0x76
00306 
00307 /* AIP31068 I2C slave address */
00308 #define AIP31068_SA    0x7C
00309 
00310 /* SSD1803 I2C slave address */
00311 #define SSD1803_SA0    0x78
00312 #define SSD1803_SA1    0x7A
00313 
00314 /* US2066/SSD1311 I2C slave address */
00315 #define US2066_SA0     0x78
00316 #define US2066_SA1     0x7A
00317 
00318 /* AC780 I2C slave address */
00319 #define AC780_SA0      0x78
00320 #define AC780_SA1      0x7A
00321 #define AC780_SA2      0x7C
00322 #define AC780_SA3      0x7E
00323 
00324 //Some native I2C controllers dont support ACK. Set define to '0' to allow code to proceed even without ACK
00325 //#define LCD_I2C_ACK    0
00326 #define LCD_I2C_ACK    1
00327 
00328 
00329 // Contrast setting, 6 significant bits (only supported for controllers with extended features)
00330 // Voltage Multiplier setting, 2 or 3 significant bits (only supported for controllers with extended features)
00331 #define LCD_DEF_CONTRAST    0x20
00332 
00333 //ST7032 EastRising ERC1602FS-4 display
00334 //Contrast setting 6 significant bits
00335 //Voltage Multiplier setting 3 significant bits
00336 #define LCD_ST7032_CONTRAST 0x28 
00337 #define LCD_ST7032_RAB      0x04
00338 
00339 //ST7036 EA DOGM1603 display
00340 //Contrast setting 6 significant bits
00341 //Voltage Multiplier setting 3 significant bits
00342 #define LCD_ST7036_CONTRAST 0x28
00343 #define LCD_ST7036_RAB      0x04
00344 
00345 //SSD1803 EA DOGM204 display
00346 //Contrast setting 6 significant bits
00347 //Voltage Multiplier setting 3 significant bits
00348 #define LCD_SSD1_CONTRAST   0x28
00349 #define LCD_SSD1_RAB        0x06
00350 
00351 //US2066/SSD1311 EastRising ER-OLEDM2002-4 display
00352 //Contrast setting 8 significant bits, use 6 for compatibility
00353 #define LCD_US20_CONTRAST   0x3F
00354 //#define LCD_US20_CONTRAST   0x1F
00355 
00356 //PCF2113, PCF2119 display
00357 //Contrast setting 6 significant bits
00358 //Voltage Multiplier setting 2 significant bits
00359 #define LCD_PCF2_CONTRAST   0x20
00360 #define LCD_PCF2_S12        0x02
00361 
00362 //PT6314 VFD display
00363 //Contrast setting 2 significant bits, use 6 for compatibility
00364 #define LCD_PT63_CONTRAST   0x3F
00365 
00366 
00367 #endif //MBED_TEXTLCDCONFIG_H