config.h

00001 #ifndef CONFIG
00002 #define CONFIG
00003 
00004 
00005 #define     DEBUG
00006 
00007 //========== device selection ==========================
00008 #define     GLD_DEVICE
00009 //#define   OID_DEVICE
00010 //#define   OID_RF_DEVICE
00011 //======================================================
00012 #define COMMAND_DEBUG
00013 
00014 #if defined(GLD_DEVICE)
00015 #define     FIRMWARE_VER        0xD // 9.13 - firmware version
00016 #define     NEW_THERMO_ADC
00017 #define     CONFIG_HFO_REG
00018 //  #define     DELTA_SF_DELAY
00019 #define     CONFIG_PLC_SINUS
00020 //  #define     CONFIG_HW_PLC
00021 //#define       CONFIG_SIMUL_HW_PLC // simulation of part of PLC regulator in FPGA
00022 #define     CONFIG_PLC_LIDEM        // PLC reg. works with demodulated LI signal (demodulation in analog IC)
00023 //  #define     CONFIG_PLC_LIM          // PLC reg. works with modulated LI signal (demodulation inside FPGA)
00024 #define     WP_TRANSITION_ENA       //e. allow the linear transition process for PLC reset //r. разрешен линейный переходной процесс при обнулении СРП
00025 
00026 #define     CONFIG_HFO_MOV_AVER_FILTER
00027 
00028 #define     CONFIG_SIX_THERMO_SENSORS
00029 
00030 #define     DEBUG_EXT_LAT_CNTR
00031 
00032 //#warning "=== GLD_DEVICE configuration selected ==="
00033 
00034 #elif defined(OID_DEVICE)
00035 #define     FIRMWARE_VER        0x1C    // 1.12 - firmware version
00036 
00037 #define     CONFIG_CURRENT_REG
00038 //  #define     CONFIG_IA_STABILIZING
00039 #define     CONFIG_LI_STABILIZING
00040 //  #define     CONFIG_IB_EQUAL_IA
00041 #define     CONFIG_IB_IA_BALANCE
00042 
00043 #define     CONFIG_HW_PLC
00044 //  #define     CONFIG_PLC_LIDEM        // PLC reg. works with demodulated LI signal (demodulation in analog IC)
00045 #define     CONFIG_PLC_LIM          // PLC reg. works with modulated LI signal (demodulation inside FPGA)
00046 //#define       CONFIG_SIMUL_HW_PLC // simulation of part of PLC regulator in FPGA
00047 #define     WP_TRANSITION_ENA       //e. allow the linear transition process for PLC reset //r. разрешен линейный переходной процесс при обнулении СРП
00048 
00049 //#warning "=== OID_DEVICE configuration selected ==="
00050 
00051 #elif defined(OID_RF_DEVICE)
00052 #define     FIRMWARE_VER        0x1C    // 1.12 - firmware version
00053 
00054 #define     CONFIG_HFO_REG
00055 
00056 #define     CONFIG_HW_PLC
00057 //  #define     CONFIG_PLC_LIDEM        // PLC reg. works with demodulated LI signal (demodulation in analog IC)
00058 #define     CONFIG_PLC_LIM          // PLC reg. works with modulated LI signal (demodulation inside FPGA)
00059 
00060 //#warning "=== OID_RF_DEVICE configuration selected ==="
00061 
00062 #else
00063 #error "Not defined Device type"
00064 #endif
00065 
00066 // -------- conditional compiles errors messages ---------------------------
00067 #if !(defined(GLD_DEVICE) ^ defined(OID_DEVICE) ^ defined(OID_RF_DEVICE))
00068 #error "Should be defined only one device, not several"
00069 #endif
00070 
00071 #if defined(CONFIG_PLC_LIDEM) & defined(CONFIG_PLC_LIM)
00072 #error "Should be defined CONFIG_PLC_LIDEM or CONFIG_PLC_LIM, not both"
00073 #endif
00074 
00075 #if !( defined(CONFIG_PLC_LIDEM) | defined(CONFIG_PLC_LIM) )
00076 #error "Not defined PLC mode: modulated / demodulated"
00077 #endif
00078 
00079 #if defined(OID_DEVICE)
00080 #if defined(CONFIG_IA_STABILIZING) & defined(CONFIG_LI_STABILIZING)
00081 #error "Should be defined CONFIG_IA_STABILIZING or CONFIG_LI_STABILIZING, not both"
00082 #endif
00083 
00084 #if !( defined(CONFIG_IA_STABILIZING) | defined(CONFIG_LI_STABILIZING) )
00085 #error "Not defined IA regulator mode: select CONFIG_IA_STABILIZING or CONFIG_LI_STABILIZING"
00086 #endif
00087 
00088 #if defined(CONFIG_IB_EQUAL_IA) & defined(CONFIG_IB_IA_BALANCE)
00089 #error "Should be defined CONFIG_IB_EQUAL_IA or CONFIG_IB_IA_BALANCE, not both"
00090 #endif
00091 
00092 #if !( defined(CONFIG_IB_EQUAL_IA) | defined(CONFIG_IB_IA_BALANCE) )
00093 #error "Not defined IB regulator mode: select CONFIG_IB_EQUAL_IA or CONFIG_IB_IA_BALANCE"
00094 #endif
00095 #endif // OID_DEVICE
00096 
00097 #endif