File content as of revision 34:9d5afa33df5d:

#include <stdlib.h>

#include "utils.h"
#include "inc/adi_sense_log.h"

void utils_printStatus(
    ADI_SENSE_STATUS *pStatus)
{
    ADI_SENSE_LOG_INFO("Status Summary:");

    if (pStatus->deviceStatus == 0)
    {
        ADI_SENSE_LOG_INFO("\tNo errors detected");
    }
    else
    {
        if (pStatus->deviceStatus & ADI_SENSE_DEVICE_STATUS_BUSY)
            ADI_SENSE_LOG_INFO("\tCommand running");
        if (pStatus->deviceStatus & ADI_SENSE_DEVICE_STATUS_DATAREADY)
            ADI_SENSE_LOG_INFO("\tData ready");
        if (pStatus->deviceStatus & ADI_SENSE_DEVICE_STATUS_ERROR)
            ADI_SENSE_LOG_INFO("\tActive Errors - RESET REQUIRED");
        if (pStatus->deviceStatus & ADI_SENSE_DEVICE_STATUS_FIFO_ERROR)
            ADI_SENSE_LOG_INFO("\tActive FIFO Errors - ATTENTION REQUIRED");
        if (pStatus->deviceStatus & ADI_SENSE_DEVICE_STATUS_CONFIG_ERROR)
            ADI_SENSE_LOG_INFO("\tActive Configuration Errors - ATTENTION REQUIRED");
        if (pStatus->deviceStatus & ADI_SENSE_DEVICE_STATUS_LUT_ERROR)
            ADI_SENSE_LOG_INFO("\tActive Look-Up Table Errors - ATTENTION REQUIRED");
        if (pStatus->deviceStatus & ADI_SENSE_DEVICE_STATUS_EXT_FLASH_ERROR)
            ADI_SENSE_LOG_INFO("\tActive External Flash Errors - ATTENTION REQUIRED");

        if (pStatus->deviceStatus & ADI_SENSE_DEVICE_STATUS_ERROR)
        {
            ADI_SENSE_LOG_INFO("\tActive Errors - ATTENTION REQUIRED");
            ADI_SENSE_LOG_INFO("\t\tLast Error Code: %u (0x%X)",
                               pStatus->errorCode, pStatus->errorCode);

            if (pStatus->diagnosticsStatus == 0)
            {
                ADI_SENSE_LOG_INFO("\t\tNo diagnostics faults detected");
            }
            else
            {
                ADI_SENSE_LOG_INFO("\t\tActive diagnostics faults:");

                if (pStatus->diagnosticsStatus & ADI_SENSE_DIAGNOSTICS_STATUS_CHECKSUM_ERROR)
                    ADI_SENSE_LOG_INFO("\t\t\tInternal Checksum fault detected");
                if (pStatus->diagnosticsStatus & ADI_SENSE_DIAGNOSTICS_STATUS_COMMS_ERROR)
                    ADI_SENSE_LOG_INFO("\t\t\tInternal Communications fault detected");
                if (pStatus->diagnosticsStatus & ADI_SENSE_DIAGNOSTICS_STATUS_SUPPLY_MONITOR_ERROR)
                    ADI_SENSE_LOG_INFO("\t\t\tSupply Monitor fault detected");
                if (pStatus->diagnosticsStatus & ADI_SENSE_DIAGNOSTICS_STATUS_SUPPLY_CAP_ERROR)
                    ADI_SENSE_LOG_INFO("\t\t\tSupply Regulator Capacitor fault detected");
                if (pStatus->diagnosticsStatus & ADI_SENSE_DIAGNOSTICS_STATUS_CONVERSION_ERROR)
                    ADI_SENSE_LOG_INFO("\t\t\tInternal ADC Conversions fault detected");
                if (pStatus->diagnosticsStatus & ADI_SENSE_DIAGNOSTICS_STATUS_CALIBRATION_ERROR)
                    ADI_SENSE_LOG_INFO("\t\t\tInternal Device Calibrations fault detected");
            }
        }

        if (pStatus->deviceStatus & ADI_SENSE_DEVICE_STATUS_ALERT)
        {
            ADI_SENSE_LOG_INFO("\tActive Alerts - ATTENTION REQUIRED:");
            ADI_SENSE_LOG_INFO("\t\tLast Alert Code: %u (0x%X)",
                               pStatus->alertCode, pStatus->alertCode);

            for (unsigned i = 0; i < ADI_SENSE_1000_MAX_CHANNELS; i++)
            {
                if (pStatus->channelAlerts[i] == 0)
                    continue;

                ADI_SENSE_LOG_INFO("\t\tChannel #%u:", i);
                ADI_SENSE_LOG_INFO("\t\t\tLast Alert Code: %u (0x%X)",
                                   pStatus->channelAlertCodes[i],
                                   pStatus->channelAlertCodes[i]);
                if (pStatus->channelAlerts[i] & ADI_SENSE_CHANNEL_ALERT_TIMEOUT)
                    ADI_SENSE_LOG_INFO("\t\t\tTimeout alert detected");
                if (pStatus->channelAlerts[i] & ADI_SENSE_CHANNEL_ALERT_UNDER_RANGE)
                    ADI_SENSE_LOG_INFO("\t\t\tUnder Range alert detected");
                if (pStatus->channelAlerts[i] & ADI_SENSE_CHANNEL_ALERT_OVER_RANGE)
                    ADI_SENSE_LOG_INFO("\t\t\tOver Range alert detected");
                if (pStatus->channelAlerts[i] & ADI_SENSE_CHANNEL_ALERT_LOW_LIMIT)
                    ADI_SENSE_LOG_INFO("\t\t\tLow limit alert detected");
                if (pStatus->channelAlerts[i] & ADI_SENSE_CHANNEL_ALERT_HIGH_LIMIT)
                    ADI_SENSE_LOG_INFO("\t\t\tHigh Limit alert detected");
                if (pStatus->channelAlerts[i] & ADI_SENSE_CHANNEL_ALERT_SENSOR_OPEN)
                    ADI_SENSE_LOG_INFO("\t\t\tSensor Fault alert detected");
                if (pStatus->channelAlerts[i] & ADI_SENSE_CHANNEL_ALERT_REF_DETECT)
                    ADI_SENSE_LOG_INFO("\t\t\tReference Detection alert detected");
                if (pStatus->channelAlerts[i] & ADI_SENSE_CHANNEL_ALERT_CONFIG_ERR)
                    ADI_SENSE_LOG_INFO("\t\t\tConfiguration Error alert detected");
                if (pStatus->channelAlerts[i] & ADI_SENSE_CHANNEL_ALERT_LUT_ERR)
                    ADI_SENSE_LOG_INFO("\t\t\tLook-Up Table Error alert detected");
                if (pStatus->channelAlerts[i] & ADI_SENSE_CHANNEL_ALERT_SENSOR_NOT_READY)
                    ADI_SENSE_LOG_INFO("\t\t\tSensor Not Ready alert detected");
                if (pStatus->channelAlerts[i] & ADI_SENSE_CHANNEL_ALERT_COMP_NOT_READY)
                    ADI_SENSE_LOG_INFO("\t\t\tCompensation Channel Not Ready alert detected");
                if (pStatus->channelAlerts[i] & ADI_SENSE_CHANNEL_ALERT_LUT_UNDER_RANGE)
                    ADI_SENSE_LOG_INFO("\t\t\tUnder Look-Up Table Range alert detected");
                if (pStatus->channelAlerts[i] & ADI_SENSE_CHANNEL_ALERT_LUT_OVER_RANGE)
                    ADI_SENSE_LOG_INFO("\t\t\tOver Look-Up Table Range alert detected");
            }
        }
    }
}

void utils_printSamples(
    ADI_SENSE_DATA_SAMPLE *pSampleBuffer,
    uint32_t nNumSamples,
    ADI_SENSE_MEASUREMENT_MODE eMeasurementMode)
{
    bool fftMode = (eMeasurementMode == ADI_SENSE_MEASUREMENT_MODE_FFT);

    for (uint32_t i = 0; i < nNumSamples; i++)
    {
        if (fftMode)
        {
            ADI_SENSE_LOG_INFO("Sample # %2d Channel # %2d :: Bin/Raw %8d  :: Magnitude %e :: flags:%s%s",
                               i+1,
                               pSampleBuffer[i].channelId,
                               pSampleBuffer[i].rawValue,
                               pSampleBuffer[i].processedValue,
                               pSampleBuffer[i].status & ADI_SENSE_DEVICE_STATUS_ERROR ? " ERROR" : "",
                               pSampleBuffer[i].status & ADI_SENSE_DEVICE_STATUS_ALERT ? " ALERT" : "");
        }
        else
        {
            ADI_SENSE_LOG_INFO("Sample # %2d Channel # %2d :: Raw %8d  :: Processed %f :: flags:%s%s",
                               i+1,
                               pSampleBuffer[i].channelId,
                               pSampleBuffer[i].rawValue,
                               pSampleBuffer[i].processedValue,
                               pSampleBuffer[i].status & ADI_SENSE_DEVICE_STATUS_ERROR ? " ERROR" : "",
                               pSampleBuffer[i].status & ADI_SENSE_DEVICE_STATUS_ALERT ? " ALERT" : "");
        }
    }
}

static void gpioCallbackFn(ADI_SENSE_GPIO_PIN ePinId, void * pArg)
{
    volatile bool_t *pbFlag = (volatile bool_t *)pArg;
    *pbFlag = true;
}

ADI_SENSE_RESULT utils_registerCallbacks(
    ADI_SENSE_DEVICE_HANDLE hDevice,
    volatile bool_t *pbDataReady,
    volatile bool_t *pbError,
    volatile bool_t *pbAlert)
{
    ADI_SENSE_RESULT res;

    res = adi_sense_RegisterGpioCallback(hDevice, ADI_SENSE_GPIO_PIN_DATAREADY,
                                         gpioCallbackFn, (void *)pbDataReady);
    if (res != ADI_SENSE_SUCCESS)
    {
        ADI_SENSE_LOG_ERROR("Failed to register DATAREADY callback");
        return res;
    }

    res = adi_sense_RegisterGpioCallback(hDevice, ADI_SENSE_GPIO_PIN_ERROR,
                                         gpioCallbackFn, (void *)pbError);
    if (res != ADI_SENSE_SUCCESS)
    {
        ADI_SENSE_LOG_ERROR("Failed to register ERROR callback");
        return res;
    }

    res = adi_sense_RegisterGpioCallback(hDevice, ADI_SENSE_GPIO_PIN_ALERT,
                                         gpioCallbackFn, (void *)pbAlert);
    if (res != ADI_SENSE_SUCCESS)
    {
        ADI_SENSE_LOG_ERROR("Failed to register ALERT callback");
        return res;
    }

    return ADI_SENSE_SUCCESS;
}

ADI_SENSE_RESULT utils_deregisterCallbacks(
    ADI_SENSE_DEVICE_HANDLE hDevice)
{
    ADI_SENSE_RESULT res;

    res = adi_sense_RegisterGpioCallback(hDevice, ADI_SENSE_GPIO_PIN_DATAREADY,
                                         NULL, NULL);
    if (res != ADI_SENSE_SUCCESS)
    {
        ADI_SENSE_LOG_ERROR("Failed to deregister DATAREADY callback");
        return res;
    }

    res = adi_sense_RegisterGpioCallback(hDevice, ADI_SENSE_GPIO_PIN_ERROR,
                                         NULL, NULL);
    if (res != ADI_SENSE_SUCCESS)
    {
        ADI_SENSE_LOG_ERROR("Failed to deregister ERROR callback");
        return res;
    }

    res = adi_sense_RegisterGpioCallback(hDevice, ADI_SENSE_GPIO_PIN_ALERT,
                                         NULL, NULL);
    if (res != ADI_SENSE_SUCCESS)
    {
        ADI_SENSE_LOG_INFO("Failed to deregister ALERT callback");
        return res;
    }

    return ADI_SENSE_SUCCESS;
}

ADI_SENSE_RESULT utils_runMeasurement(
    ADI_SENSE_DEVICE_HANDLE hDevice,
    ADI_SENSE_MEASUREMENT_MODE eMeasurementMode)
{
    ADI_SENSE_RESULT res;

    volatile bool_t bDataReady = false;
    volatile bool_t bError = false;
    volatile bool_t bAlert = false;
    res = utils_registerCallbacks(hDevice, &bDataReady, &bError, &bAlert);
    if (res != ADI_SENSE_SUCCESS)
        return res;

    /*
     * Retrieve the number of samples per cycle, per DATAREADY pulse, etc. for
     * this configuration.
     */
    ADI_SENSE_1000_OPERATING_MODE eOperatingMode;
    ADI_SENSE_1000_DATAREADY_MODE eDataReadyMode;
    uint32_t nSamplesPerDataready;
    uint32_t nSamplesPerCycle;
    uint8_t nBytesPerSample;
    res = adi_sense_1000_GetDataReadyModeInfo(hDevice,
                                              eMeasurementMode,
                                              &eOperatingMode,
                                              &eDataReadyMode,
                                              &nSamplesPerDataready,
                                              &nSamplesPerCycle,
                                              &nBytesPerSample);
    if (res != ADI_SENSE_SUCCESS)
        return res;

    /*
     * Allocate a buffer to store the samples retrieved on each DATAREADY pulse
     */
    ADI_SENSE_DATA_SAMPLE *pSampleBuffer;
    pSampleBuffer = malloc(sizeof(ADI_SENSE_DATA_SAMPLE) *
                           nSamplesPerDataready);
    if (pSampleBuffer == NULL)
    {
        ADI_SENSE_LOG_ERROR("Failed to allocate sample buffer");
        return ADI_SENSE_NO_MEM;
    }

    /*
     * Kick off the measurement cycle(s) here
     */
    res = adi_sense_StartMeasurement(hDevice, eMeasurementMode);
    if (res != ADI_SENSE_SUCCESS)
    {
        ADI_SENSE_LOG_ERROR("Failed to start measurement");
        return res;
    }

    /*
     * Loop continuously unless operating mode is single-cycle
     */
    uint32_t nSampleCount = 0;
    while (true)
    {
        ADI_SENSE_STATUS status;
        uint32_t nReturned;

        /*
         * Wait until the next batch of 1 or more samples is ready, continuously
         * checking DATAREADY until it is asserted
         */
        while (! (bDataReady || bError))
            ;

        if (!bError)
        {
            /*
             * Get data samples from the measurement cycle, if no error has occurred
             */
            bDataReady = false;
            res = adi_sense_GetData(hDevice, eMeasurementMode, pSampleBuffer,
                                    nBytesPerSample, nSamplesPerDataready,
                                    &nReturned);
            if (res != ADI_SENSE_SUCCESS)
            {
                if (res == ADI_SENSE_INCOMPLETE)
                {
                    /*
                     * This is expected in cases where cycleSkipCount may
                     * be non-zero for some channels, resulting in
                     * variable-length sequences
                     */
                    ADI_SENSE_LOG_DEBUG("Retrieved %u of %u requested data samples",
                                        nReturned, nSamplesPerDataready);
                }
                else
                {
                    ADI_SENSE_LOG_WARN("Failed to get data samples from device");
                    return res;
                }
            }

            /*
             * Display the data samples.
             *
             * NOTE: this requires a sufficient idle time between subsequent
             * DATAREADY pulses to allow printing to occur.  Otherwise,
             * subsequent samples may be missed if not retrieved promptly when
             * the next DATAREADY assertion occurs.
             */
            utils_printSamples(pSampleBuffer, nReturned, eMeasurementMode);
            nSampleCount += nReturned;
        }

        /*
         * Check and print device status if errors/alerts have been triggered
         */
        if (bError || bAlert)
        {
            res = adi_sense_GetStatus(hDevice, &status);
            if (res != ADI_SENSE_SUCCESS)
            {
                ADI_SENSE_LOG_ERROR("Failed to retrieve device status");
                return res;
            }

            if (status.deviceStatus &
                (ADI_SENSE_DEVICE_STATUS_ERROR | ADI_SENSE_DEVICE_STATUS_ALERT))
            {
                utils_printStatus(&status);

                /* Break out of the loop if any errors are raised */
                if (bError)
                    break;
            }
        }

        if (eOperatingMode == ADI_SENSE_1000_OPERATING_MODE_SINGLECYCLE)
        {
            /*
             * In this mode, break out of the loop when the measurement command
             * has completed.
             *
             * One option is to check for the expected number of samples to be
             * returned for the cycle.  However, cycles may have variable-length
             * sequences if the cycleSkipCount option is non-zero for any of the
             * channels.
             *
             * So, instead, we check for the command-running status, which
             * will de-assert in this mode when the measurement command has
             * completed a single cycle.
             */
            bool_t bCommandRunning;
            res = adi_sense_GetCommandRunningState(hDevice, &bCommandRunning);
            if (res != ADI_SENSE_SUCCESS)
            {
                ADI_SENSE_LOG_ERROR("Failed to get command-running status");
                return res;
            }

            if (!bCommandRunning && !bDataReady)
                break;
        }
    }

    res = adi_sense_StopMeasurement(hDevice);
    if (res != ADI_SENSE_SUCCESS)
    {
        ADI_SENSE_LOG_ERROR("Failed to send stop measurement");
        return res;
    }

    free(pSampleBuffer);

    res = utils_deregisterCallbacks(hDevice);
    if (res != ADI_SENSE_SUCCESS)
        return res;

    return ADI_SENSE_SUCCESS;
}