Diff: targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F437xG/TARGET_UBLOX_C030/system_clock.c

Revision:

168:9672193075cf

Child:

171:89b338f31ef1

--- /dev/null	Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/TARGET_STM/TARGET_STM32F4/TARGET_STM32F437xG/TARGET_UBLOX_C030/system_clock.c	Thu Jul 06 15:42:05 2017 +0100
@@ -0,0 +1,183 @@
+/* mbed Microcontroller Library
+* Copyright (c) 2006-2017 ARM Limited
+*
+* Licensed under the Apache License, Version 2.0 (the "License");
+* you may not use this file except in compliance with the License.
+* You may obtain a copy of the License at
+*
+*     http://www.apache.org/licenses/LICENSE-2.0
+*
+* Unless required by applicable law or agreed to in writing, software
+* distributed under the License is distributed on an "AS IS" BASIS,
+* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
+* See the License for the specific language governing permissions and
+* limitations under the License.
+*/
+
+/**
+  * This file configures the system clock as follows:
+  *----------------------------------------------------------------------------------------------------------------------------------------
+  * System clock source                | PLL_HSE_XTAL           | PLL_HSE_XTAL           | PLL_HSE_XTAL           | PLL_HSE_XTAL
+  *                                    | (external 8 MHz clock) | (external 8 MHz clock) | (external 12 MHz clock)| (external 12 MHz clock)
+  *----------------------------------------------------------------------------------------------------------------------------------------
+  * SYSCLK(MHz)                        | 168                    | 84                     | 168                    | 84
+  *----------------------------------------------------------------------------------------------------------------------------------------
+  * AHBCLK (MHz)                       | 168                    | 84                     | 168                    | 84
+  *----------------------------------------------------------------------------------------------------------------------------------------
+  * APB1CLK (MHz)                      | 42                     | 42                     | 42                     | 42
+  *----------------------------------------------------------------------------------------------------------------------------------------
+  * APB2CLK (MHz)                      | 84                     | 84                     | 84                     | 84
+  *----------------------------------------------------------------------------------------------------------------------------------------
+  * USB capable (48 MHz precise clock) | YES                    | YES                    | YES                    | YES
+  *----------------------------------------------------------------------------------------------------------------------------------------
+**/
+
+#include "ublox_low_level_api.h"
+#include "stm32f4xx.h"
+
+/*!< Uncomment the following line if you need to relocate your vector Table in
+     Internal SRAM. */
+/* #define VECT_TAB_SRAM */
+#define VECT_TAB_OFFSET  0x00 /*!< Vector Table base offset field.
+                                   This value must be a multiple of 0x200. */
+
+
+/* Select the SYSCLOCK  to start with (0=OFF, 1=ON) */
+#define USE_SYSCLOCK_168 (1) /* Use external 8MHz or 12 MHz xtal and sets SYSCLK to 168MHz */
+#define USE_SYSCLOCK_84 (0) /* Use external 8MHz or 12 MHz xtal and sets SYSCLK to 84MHz */
+
+
+void SetSysClock(void);
+
+/**
+  * @brief  Setup the microcontroller system
+  *         Initialize the FPU setting, vector table location and External memory
+  *         configuration.
+  * @param  None
+  * @retval None
+  */
+void SystemInit(void)
+{
+    /* FPU settings ------------------------------------------------------------*/
+#if (__FPU_PRESENT == 1) && (__FPU_USED == 1)
+    SCB->CPACR |= ((3UL << 10*2)|(3UL << 11*2));  /* set CP10 and CP11 Full Access */
+#endif
+    /* Reset the RCC clock configuration to the default reset state ------------*/
+    /* Set HSION bit */
+    RCC->CR |= (uint32_t)0x00000001;
+
+    /* Reset CFGR register */
+    RCC->CFGR = 0x00000000;
+
+    /* Reset HSEON, CSSON and PLLON bits */
+    RCC->CR &= (uint32_t)0xFEF6FFFF;
+
+    /* Reset PLLCFGR register */
+    RCC->PLLCFGR = 0x24003010;
+
+    /* Reset HSEBYP bit */
+    RCC->CR &= (uint32_t)0xFFFBFFFF;
+
+    /* Disable all interrupts */
+    RCC->CIR = 0x00000000;
+
+#if defined (DATA_IN_ExtSRAM) || defined (DATA_IN_ExtSDRAM)
+    SystemInit_ExtMemCtl();
+#endif /* DATA_IN_ExtSRAM || DATA_IN_ExtSDRAM */
+
+    /* Configure the Vector Table location add offset address ------------------*/
+#ifdef VECT_TAB_SRAM
+    SCB->VTOR = SRAM_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal SRAM */
+#else
+    SCB->VTOR = FLASH_BASE | VECT_TAB_OFFSET; /* Vector Table Relocation in Internal FLASH */
+#endif
+
+    ublox_board_init();
+}
+
+
+
+/** System Clock Configuration
+*/
+#if USE_SYSCLOCK_168 != 0
+/*
+ * Set SYSCLK=168MHZ
+ */
+void SetSysClock(void)
+{
+
+    RCC_OscInitTypeDef RCC_OscInitStruct;
+    RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+    __HAL_RCC_PWR_CLK_ENABLE();
+
+    __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
+
+    RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+    RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+    RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+    RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+#ifdef USE_DEBUG_8MHz_XTAL
+    RCC_OscInitStruct.PLL.PLLM = 8;
+#else
+    RCC_OscInitStruct.PLL.PLLM = 12;
+#endif
+    RCC_OscInitStruct.PLL.PLLN = 336;
+    RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
+    RCC_OscInitStruct.PLL.PLLQ = 7;
+    HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+    RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
+                                  |RCC_CLOCKTYPE_PCLK2;
+    RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+    RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+    RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
+    RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
+    HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_5);
+
+    // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
+
+
+}
+
+#elif USE_SYSCLOCK_84 != 0
+/*
+Set SYSCLK=84MHZ
+ */
+void SetSysClock(void)
+{
+
+    RCC_OscInitTypeDef RCC_OscInitStruct;
+    RCC_ClkInitTypeDef RCC_ClkInitStruct;
+
+    __HAL_RCC_PWR_CLK_ENABLE();
+
+    __HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE3);
+
+    RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+    RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+    RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
+    RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
+#ifdef USE_DEBUG_8MHz_XTAL
+    RCC_OscInitStruct.PLL.PLLM = 8;
+#else
+    RCC_OscInitStruct.PLL.PLLM = 12;
+#endif
+    RCC_OscInitStruct.PLL.PLLN = 336;
+    RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV4;
+    RCC_OscInitStruct.PLL.PLLQ = 7;
+    HAL_RCC_OscConfig(&RCC_OscInitStruct);
+
+
+    RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_SYSCLK|RCC_CLOCKTYPE_PCLK1
+                                  |RCC_CLOCKTYPE_PCLK2;
+    RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
+    RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
+    RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;
+    RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
+    HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2);
+
+    // HAL_RCC_MCOConfig(RCC_MCO2, RCC_MCO2SOURCE_SYSCLK, RCC_MCODIV_3);
+
+}
+#endif