Renesas
The "GR-PEACH_Audio_Playback_7InchLCD_Sample" is a sample code that can provides high-resolution audio playback of FLAC format files. It also allows the user to audio-playback control functions such as play, pause, and stop by manipulating key switches.
Dependencies: GR-PEACH_video R_BSP TLV320_RBSP USBHost_custom
Fork of
GR-PEACH_Audio_Playback_Sample
by 
Renesas
Note
For a sample program of without LCD Board, please refer to GR-PEACH_Audio_Playback_Sample.
Introduction
The "GR-PEACH_Audio_Playback_7InchLCD_Sample" is a sample code that can provides high-resolution audio playback of FLAC format files. It also allows the user to audio-playback control functions such as play, pause, and stop by manipulating key switches.
1. Overview of the Sample Code
1.1 Software Block Diagram
Figure 1.1 shows the software block diagram.
1.2 Pin Definitions
Table 1.1 shows the pins used in this sample code.
2. Sample Code Operating Environment
In order to operate this sample code, GR-PEACH, Audio Camera Shield and 7.1 inch LCD Shield must be needed. For details on Audio Camera Shield and 7.1 inch LCD Shield, please refer to the following links, respectively:
- Audio Camera Shield
https://developer.mbed.org/teams/Renesas/wiki/Audio_Camera-shield - 7.1 inch LCD Shield
https://developer.mbed.org/teams/Renesas/wiki/LCD-shield
In this section, it is described that how board is configured and to control audio playback via command line and touch screen.
2.1 Operating Environment
Figure 2.1 shows the overview of the operating environment for this sample code.
Figure 2.2 and 2.3 show how to configure GR-PEACH, Audio Camera Shield and 7.1 inch LCD shield when using USB0 and USB1, respectively.
Table 2.1 lists the overview of Graphical User Interface (GUI) of this sample code.
2.2 List of User Operations
Table 2.2 shows the relationship among Audio Playback, Command Line and Onboard Switch.
3. Function Outline
Table 3.1, 3.2 and 3.3 shows the overview of functions implemented in this sample code.
3.1 Playback Control
This sample program supports the operation "play", "pause", "stop", "play next song" and "play previous song".
3.2 Trick Play Control
In order to enable/disable Repeat Mode, user need to type "repeat" on command line or click the corresponding icon shown in Table 2.2. By derault, Repeat Mode is enabled. When Repeat Mode is enabled, the first song is played back after the playback of the last song is finished. Otherwise, the playback is shopped when finishing to play back the last song.
3.3 How to see Song Information
The information of the song being played back can be seen by typing playinfo on command line. Table 3.4 lists the items user can see on the terminal.
3.4 How to analyze the folder structure in USB stick
In this sample code, the folder structure in USB stick is analyzed in the breadth-first order. Table 3.5 shows how the files in USB stick are numbered.
4.Others
4.1 Serial Communication Setting
With respect to the default serial communication related setting on mbed, please refer to the follwing link:
https://developer.mbed.org/teams/Renesas/wiki/GR-PEACH-Getting-Started#install-the-usb-serial-communication
Please set up the terminal software you would like to use on your PC in consideration of the above. For example, 9600 should be specified for the baud rate on the terminal in order to control this sample via command line.
4.2 Necessary modification when using GCC ARM Embedded
If you would like to use GCC ARM Embedded, you must revise the following linker script incorporated in mbed OS 5 package as follows:
- Linker Script to be modified
$(PROJECT_ROOT)/mbed-os/targets/TARGET_RENESAS/TARGET_RZ_A1H/device/TOOLCHAIN_GCC_ARM/RZA1H.ld
Please note that $(PROJECT_ROOT) in the above denotes the root directory of this sample code
- Before Modification
RZA1H.ld
/* Linker script for mbed RZ_A1H */
/* Linker script to configure memory regions. */
MEMORY
{
ROM (rx) : ORIGIN = 0x00000000, LENGTH = 0x02000000
BOOT_LOADER (rx) : ORIGIN = 0x18000000, LENGTH = 0x00004000
SFLASH (rx) : ORIGIN = 0x18004000, LENGTH = 0x07FFC000
L_TTB (rw) : ORIGIN = 0x20000000, LENGTH = 0x00004000
RAM (rwx) : ORIGIN = 0x20020000, LENGTH = 0x00700000
RAM_NC (rwx) : ORIGIN = 0x20900000, LENGTH = 0x00100000
}
(snip)
- After Modification
RZA1H.ld
/* Linker script for mbed RZ_A1H */
/* Linker script to configure memory regions. */
MEMORY
{
ROM (rx) : ORIGIN = 0x00000000, LENGTH = 0x02000000
BOOT_LOADER (rx) : ORIGIN = 0x18000000, LENGTH = 0x00004000
SFLASH (rx) : ORIGIN = 0x18004000, LENGTH = 0x07FFC000
L_TTB (rw) : ORIGIN = 0x20000000, LENGTH = 0x00004000
RAM (rwx) : ORIGIN = 0x20020000, LENGTH = 0x00180000
RAM_NC (rwx) : ORIGIN = 0x20200000, LENGTH = 0x00680000
}
(snip)
Diff: main/system.cpp
- Revision:
- 4:2672de88a46b
- Parent:
- 2:d9fca8cd7f03
- Child:
- 5:25de5b925302
--- a/main/system.cpp Mon Dec 07 05:08:45 2015 +0000
+++ b/main/system.cpp Mon Jan 25 02:41:36 2016 +0000
@@ -112,6 +112,7 @@
SYS_EV_KEY_PLAYINFO, /* "PLAYINFO" key */
SYS_EV_KEY_REPEAT, /* "REPEAT" key */
SYS_EV_KEY_HELP, /* "HELP" key */
+ SYS_EV_KEY_MODE, /* "MODE" key */
/* Notification of decoder process */
SYS_EV_DEC_OPEN_COMP, /* Finished the opening process */
SYS_EV_DEC_OPEN_COMP_ERR, /* Finished the opening process (An error occured)*/
@@ -142,6 +143,7 @@
uint32_t total_time; /* Total playback time */
uint32_t sample_rate; /* Sampling rate in Hz of FLAC file */
uint32_t channel_num; /* Number of channel */
+ uint32_t disp_mode; /* Display mode */
} play_info_t;
/* Control data of main thread */
@@ -202,6 +204,8 @@
static void print_file_name(const play_info_t * const p_info,
const fid_scan_folder_t * const p_data);
static void print_help_info(void);
+static void print_play_status(const play_info_t * const p_info);
+static void change_display_mode(play_info_t * const p_info);
static uint32_t convert_track_id(const uint32_t trk_id);
static bool send_mail(const SYS_MAIL_ID mail_id, const uint32_t param0,
const uint32_t param1, const uint32_t param2);
@@ -228,6 +232,8 @@
/* Initializes the control data of main thread. */
init_ctrl_data(&sys_ctrl);
+ /* Notifies the default display mode. */
+ (void) dsp_notify_disp_mode(sys_ctrl.play_info.disp_mode);
sys_stat = SYS_ST_WAIT_USB_CONNECT;
while (1) {
sys_ev = check_usb_event(sys_stat, &sys_ctrl.usb_ctrl, &msd);
@@ -305,6 +311,7 @@
p_ctrl->play_info.total_time = 0u;
p_ctrl->play_info.sample_rate = 0u;
p_ctrl->play_info.channel_num = 0u;
+ p_ctrl->play_info.disp_mode = DSP_DISPMODE_1;
}
}
@@ -349,6 +356,9 @@
case SYS_KEYCODE_HELP:
ret = SYS_EV_KEY_HELP;
break;
+ case SYS_KEYCODE_MODE:
+ ret = SYS_EV_KEY_MODE;
+ break;
default:
/* Unexpected cases : This is fail-safe processing. */
ret = SYS_EV_NON;
@@ -519,6 +529,8 @@
next_stat = SYS_ST_STOP;
} else if (event == SYS_EV_KEY_HELP) {
print_help_info();
+ } else if (event == SYS_EV_KEY_MODE) {
+ change_display_mode(&p_ctrl->play_info);
} else {
/* DO NOTHING */
}
@@ -555,6 +567,9 @@
case SYS_EV_KEY_HELP:
print_help_info();
break;
+ case SYS_EV_KEY_MODE:
+ change_display_mode(&p_ctrl->play_info);
+ break;
case SYS_EV_USB_DISCONNECT:
p_ctrl->usb_ctrl.usb_flag_detach = true;
next_stat = SYS_ST_WAIT_USB_CONNECT;
@@ -606,6 +621,9 @@
case SYS_EV_KEY_HELP:
print_help_info();
break;
+ case SYS_EV_KEY_MODE:
+ change_display_mode(&p_ctrl->play_info);
+ break;
case SYS_EV_DEC_OPEN_COMP:
result = is_track_changed(&p_ctrl->play_info);
if (result == true) {
@@ -616,6 +634,7 @@
next_stat = SYS_ST_STOP_PREPARE_REQ;
} else {
/* Unexpected cases : This is fail-safe processing. */
+ print_play_status(&p_ctrl->play_info);
exe_end_proc(&p_ctrl->play_info);
next_stat = SYS_ST_STOP;
}
@@ -630,6 +649,7 @@
next_stat = SYS_ST_STOP_PREPARE;
} else {
/* Unexpected cases : This is fail-safe processing. */
+ print_play_status(&p_ctrl->play_info);
exe_end_proc(&p_ctrl->play_info);
next_stat = SYS_ST_STOP;
}
@@ -638,6 +658,7 @@
break;
case SYS_EV_DEC_OPEN_COMP_ERR:
/* Output error message to PC */
+ print_play_status(&p_ctrl->play_info);
(void) dsp_notify_print_string(PRINT_MSG_DECODE_ERR);
exe_end_proc(&p_ctrl->play_info);
next_stat = SYS_ST_STOP;
@@ -677,6 +698,9 @@
case SYS_EV_KEY_HELP:
print_help_info();
break;
+ case SYS_EV_KEY_MODE:
+ change_display_mode(&p_ctrl->play_info);
+ break;
case SYS_EV_DEC_OPEN_COMP:
print_play_time(&p_ctrl->play_info);
result = exe_close_proc();
@@ -684,6 +708,7 @@
next_stat = SYS_ST_STOP_PREPARE;
} else {
/* Unexpected cases : This is fail-safe processing. */
+ print_play_status(&p_ctrl->play_info);
exe_end_proc(&p_ctrl->play_info);
if (p_ctrl->usb_ctrl.usb_flag_detach == true) {
next_stat = SYS_ST_WAIT_USB_CONNECT;
@@ -694,6 +719,7 @@
break;
case SYS_EV_DEC_OPEN_COMP_ERR:
/* Output error message to PC */
+ print_play_status(&p_ctrl->play_info);
(void) dsp_notify_print_string(PRINT_MSG_DECODE_ERR);
exe_end_proc(&p_ctrl->play_info);
if (p_ctrl->usb_ctrl.usb_flag_detach == true) {
@@ -768,6 +794,9 @@
case SYS_EV_KEY_HELP:
print_help_info();
break;
+ case SYS_EV_KEY_MODE:
+ change_display_mode(&p_ctrl->play_info);
+ break;
case SYS_EV_STAT_STOP:
print_play_time(&p_ctrl->play_info);
result = exe_close_proc();
@@ -838,7 +867,11 @@
case SYS_EV_KEY_HELP:
print_help_info();
break;
+ case SYS_EV_KEY_MODE:
+ change_display_mode(&p_ctrl->play_info);
+ break;
case SYS_EV_DEC_CLOSE_COMP:
+ print_play_status(&p_ctrl->play_info);
exe_end_proc(&p_ctrl->play_info);
if (p_ctrl->usb_ctrl.usb_flag_detach == true) {
next_stat = SYS_ST_WAIT_USB_CONNECT;
@@ -850,6 +883,7 @@
result = exe_close_proc();
if (result != true) {
/* Unexpected cases : This is fail-safe processing. */
+ print_play_status(&p_ctrl->play_info);
exe_end_proc(&p_ctrl->play_info);
if (p_ctrl->usb_ctrl.usb_flag_detach == true) {
next_stat = SYS_ST_WAIT_USB_CONNECT;
@@ -911,6 +945,9 @@
case SYS_EV_KEY_HELP:
print_help_info();
break;
+ case SYS_EV_KEY_MODE:
+ change_display_mode(&p_ctrl->play_info);
+ break;
case SYS_EV_DEC_CLOSE_COMP:
exe_end_proc(&p_ctrl->play_info);
print_file_name(&p_ctrl->play_info, &p_ctrl->scan_data);
@@ -918,6 +955,7 @@
if (result == true) {
next_stat = SYS_ST_PLAY_PREPARE;
} else {
+ print_play_status(&p_ctrl->play_info);
next_stat = SYS_ST_STOP;
}
break;
@@ -925,6 +963,7 @@
result = exe_close_proc();
if (result != true) {
/* Unexpected cases : This is fail-safe processing. */
+ print_play_status(&p_ctrl->play_info);
exe_end_proc(&p_ctrl->play_info);
next_stat = SYS_ST_STOP;
}
@@ -1260,6 +1299,36 @@
(void) dsp_req_help();
}
+/** Prints the information of the playback status
+ *
+ * @param p_info Pointer to the playback information of the playback file
+ */
+static void print_play_status(const play_info_t * const p_info)
+{
+ if (p_info != NULL) {
+ (void) dsp_notify_play_status(p_info->play_stat);
+ }
+}
+
+/** Changes the display mode of the TFT display.
+ *
+ * @param disp_mode Display mode before the change
+ *
+ * @returns
+ * Display mode after changing
+ */
+static void change_display_mode(play_info_t * const p_info)
+{
+ if (p_info != NULL) {
+ if (p_info->disp_mode < DSP_DISPMODE_3) {
+ p_info->disp_mode++;
+ } else {
+ p_info->disp_mode = DSP_DISPMODE_1;
+ }
+ (void) dsp_notify_disp_mode(p_info->disp_mode);
+ }
+}
+
/** Converts the track ID of main thread into the track ID of display thread
*
* @param trk_id Track ID of main thread