teralytic
mbed library sources. Supersedes mbed-src.
Diff: targets/cmsis/TARGET_STM/TARGET_STM32L4/stm32l4xx_hal_rcc.h
- Revision:
- 0:9b334a45a8ff
- Child:
- 34:bb6061527455
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/targets/cmsis/TARGET_STM/TARGET_STM32L4/stm32l4xx_hal_rcc.h Thu Oct 01 15:25:22 2015 +0300
@@ -0,0 +1,3050 @@
+/**
+ ******************************************************************************
+ * @file stm32l4xx_hal_rcc.h
+ * @author MCD Application Team
+ * @version V1.0.0
+ * @date 26-June-2015
+ * @brief Header file of RCC HAL module.
+ ******************************************************************************
+ * @attention
+ *
+ * <h2><center>© COPYRIGHT(c) 2015 STMicroelectronics</center></h2>
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted provided that the following conditions are met:
+ * 1. Redistributions of source code must retain the above copyright notice,
+ * this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright notice,
+ * this list of conditions and the following disclaimer in the documentation
+ * and/or other materials provided with the distribution.
+ * 3. Neither the name of STMicroelectronics nor the names of its contributors
+ * may be used to endorse or promote products derived from this software
+ * without specific prior written permission.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE
+ * FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
+ * DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
+ * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER
+ * CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY,
+ * OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+ * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ *
+ ******************************************************************************
+ */
+
+/* Define to prevent recursive inclusion -------------------------------------*/
+#ifndef __STM32L4xx_HAL_RCC_H
+#define __STM32L4xx_HAL_RCC_H
+
+#ifdef __cplusplus
+ extern "C" {
+#endif
+
+/* Includes ------------------------------------------------------------------*/
+#include "stm32l4xx_hal_def.h"
+
+/** @addtogroup STM32L4xx_HAL_Driver
+ * @{
+ */
+
+/** @addtogroup RCC
+ * @{
+ */
+
+/* Exported types ------------------------------------------------------------*/
+/** @defgroup RCC_Exported_Types RCC Exported Types
+ * @{
+ */
+
+/**
+ * @brief RCC PLL configuration structure definition
+ */
+typedef struct
+{
+ uint32_t PLLState; /*!< The new state of the PLL.
+ This parameter can be a value of @ref RCC_PLL_Config */
+
+ uint32_t PLLSource; /*!< RCC_PLLSource: PLL entry clock source.
+ This parameter must be a value of @ref RCC_PLL_Clock_Source */
+
+ uint32_t PLLM; /*!< PLLM: Division factor for PLL VCO input clock.
+ This parameter must be a number between Min_Data = 0 and Max_Data = 8 */
+
+ uint32_t PLLN; /*!< PLLN: Multiplication factor for PLL VCO output clock.
+ This parameter must be a number between Min_Data = 8 and Max_Data = 86 */
+
+ uint32_t PLLP; /*!< PLLP: Division factor for SAI clock.
+ This parameter must be a value of @ref RCC_PLLP_Clock_Divider */
+
+ uint32_t PLLQ; /*!< PLLQ: Division factor for SDMMC1, RNG and USB clocks.
+ This parameter must be a value of @ref RCC_PLLQ_Clock_Divider */
+
+ uint32_t PLLR; /*!< PLLR: Division for the main system clock.
+ User have to set the PLLR parameter correctly to not exceed max frequency 80MHZ.
+ This parameter must be a value of @ref RCC_PLLR_Clock_Divider */
+
+}RCC_PLLInitTypeDef;
+
+/**
+ * @brief RCC Internal/External Oscillator (HSE, HSI, MSI, LSE and LSI) configuration structure definition
+ */
+typedef struct
+{
+ uint32_t OscillatorType; /*!< The oscillators to be configured.
+ This parameter can be a value of @ref RCC_Oscillator_Type */
+
+ uint32_t HSEState; /*!< The new state of the HSE.
+ This parameter can be a value of @ref RCC_HSE_Config */
+
+ uint32_t LSEState; /*!< The new state of the LSE.
+ This parameter can be a value of @ref RCC_LSE_Config */
+
+ uint32_t HSIState; /*!< The new state of the HSI.
+ This parameter can be a value of @ref RCC_HSI_Config */
+
+ uint32_t HSICalibrationValue; /*!< The calibration trimming value (default is RCC_HSICALIBRATION_DEFAULT).
+ This parameter must be a number between Min_Data = 0x00 and Max_Data = 0x1F */
+
+ uint32_t LSIState; /*!< The new state of the LSI.
+ This parameter can be a value of @ref RCC_LSI_Config */
+
+ uint32_t MSIState; /*!< The new state of the MSI.
+ This parameter can be a value of @ref RCC_MSI_Config */
+
+ uint32_t MSICalibrationValue; /*!< The calibration trimming value (default is RCC_MSICALIBRATION_DEFAULT).
+ This parameter must be a number between Min_Data = 0x00 and Max_Data = 0xFF */
+
+ uint32_t MSIClockRange; /*!< The MSI frequency range.
+ This parameter can be a value of @ref RCC_MSI_Clock_Range */
+
+ RCC_PLLInitTypeDef PLL; /*!< Main PLL structure parameters */
+
+}RCC_OscInitTypeDef;
+
+/**
+ * @brief RCC System, AHB and APB busses clock configuration structure definition
+ */
+typedef struct
+{
+ uint32_t ClockType; /*!< The clock to be configured.
+ This parameter can be a value of @ref RCC_System_Clock_Type */
+
+ uint32_t SYSCLKSource; /*!< The clock source used as system clock (SYSCLK).
+ This parameter can be a value of @ref RCC_System_Clock_Source */
+
+ uint32_t AHBCLKDivider; /*!< The AHB clock (HCLK) divider. This clock is derived from the system clock (SYSCLK).
+ This parameter can be a value of @ref RCC_AHB_Clock_Source */
+
+ uint32_t APB1CLKDivider; /*!< The APB1 clock (PCLK1) divider. This clock is derived from the AHB clock (HCLK).
+ This parameter can be a value of @ref RCC_APB1_APB2_Clock_Source */
+
+ uint32_t APB2CLKDivider; /*!< The APB2 clock (PCLK2) divider. This clock is derived from the AHB clock (HCLK).
+ This parameter can be a value of @ref RCC_APB1_APB2_Clock_Source */
+
+}RCC_ClkInitTypeDef;
+
+/**
+ * @}
+ */
+
+/* Exported constants --------------------------------------------------------*/
+/** @defgroup RCC_Exported_Constants RCC Exported Constants
+ * @{
+ */
+
+/** @defgroup RCC_Timeout_Value Timeout Values
+ * @{
+ */
+#define RCC_DBP_TIMEOUT_VALUE ((uint32_t)100)
+#define RCC_LSE_TIMEOUT_VALUE ((uint32_t)5000)
+/**
+ * @}
+ */
+
+/** @defgroup RCC_Oscillator_Type Oscillator Type
+ * @{
+ */
+#define RCC_OSCILLATORTYPE_NONE ((uint32_t)0x00000000) /*!< Oscillator configuration unchanged */
+#define RCC_OSCILLATORTYPE_HSE ((uint32_t)0x00000001) /*!< HSE to configure */
+#define RCC_OSCILLATORTYPE_HSI ((uint32_t)0x00000002) /*!< HSI to configure */
+#define RCC_OSCILLATORTYPE_LSE ((uint32_t)0x00000004) /*!< LSE to configure */
+#define RCC_OSCILLATORTYPE_LSI ((uint32_t)0x00000008) /*!< LSI to configure */
+#define RCC_OSCILLATORTYPE_MSI ((uint32_t)0x00000010) /*!< MSI to configure */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_HSE_Config HSE Config
+ * @{
+ */
+#define RCC_HSE_OFF ((uint32_t)0x00000000) /*!< HSE clock deactivation */
+#define RCC_HSE_ON RCC_CR_HSEON /*!< HSE clock activation */
+#define RCC_HSE_BYPASS ((uint32_t)(RCC_CR_HSEBYP | RCC_CR_HSEON)) /*!< External clock source for HSE clock */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_LSE_Config LSE Config
+ * @{
+ */
+#define RCC_LSE_OFF ((uint32_t)0x00000000) /*!< LSE clock deactivation */
+#define RCC_LSE_ON RCC_BDCR_LSEON /*!< LSE clock activation */
+#define RCC_LSE_BYPASS ((uint32_t)(RCC_BDCR_LSEBYP | RCC_BDCR_LSEON)) /*!< External clock source for LSE clock */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_HSI_Config HSI Config
+ * @{
+ */
+#define RCC_HSI_OFF ((uint32_t)0x00000000) /*!< HSI clock deactivation */
+#define RCC_HSI_ON RCC_CR_HSION /*!< HSI clock activation */
+
+#define RCC_HSICALIBRATION_DEFAULT ((uint32_t)16) /*!< Default HSI calibration trimming value */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_LSI_Config LSI Config
+ * @{
+ */
+#define RCC_LSI_OFF ((uint32_t)0x00000000) /*!< LSI clock deactivation */
+#define RCC_LSI_ON RCC_CSR_LSION /*!< LSI clock activation */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_MSI_Config MSI Config
+ * @{
+ */
+#define RCC_MSI_OFF ((uint32_t)0x00000000) /*!< MSI clock deactivation */
+#define RCC_MSI_ON RCC_CR_MSION /*!< MSI clock activation */
+
+#define RCC_MSICALIBRATION_DEFAULT ((uint32_t)0) /*!< Default MSI calibration trimming value */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_PLL_Config PLL Config
+ * @{
+ */
+#define RCC_PLL_NONE ((uint32_t)0x00000000) /*!< PLL configuration unchanged */
+#define RCC_PLL_OFF ((uint32_t)0x00000001) /*!< PLL deactivation */
+#define RCC_PLL_ON ((uint32_t)0x00000002) /*!< PLL activation */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_PLLP_Clock_Divider PLLP Clock Divider
+ * @{
+ */
+#define RCC_PLLP_DIV7 ((uint32_t)0x00000007) /*!< PLLP division factor = 7 */
+#define RCC_PLLP_DIV17 ((uint32_t)0x00000011) /*!< PLLP division factor = 17 */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_PLLQ_Clock_Divider PLLQ Clock Divider
+ * @{
+ */
+#define RCC_PLLQ_DIV2 ((uint32_t)0x00000002) /*!< PLLQ division factor = 2 */
+#define RCC_PLLQ_DIV4 ((uint32_t)0x00000004) /*!< PLLQ division factor = 4 */
+#define RCC_PLLQ_DIV6 ((uint32_t)0x00000006) /*!< PLLQ division factor = 6 */
+#define RCC_PLLQ_DIV8 ((uint32_t)0x00000008) /*!< PLLQ division factor = 8 */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_PLLR_Clock_Divider PLLR Clock Divider
+ * @{
+ */
+#define RCC_PLLR_DIV2 ((uint32_t)0x00000002) /*!< PLLR division factor = 2 */
+#define RCC_PLLR_DIV4 ((uint32_t)0x00000004) /*!< PLLR division factor = 4 */
+#define RCC_PLLR_DIV6 ((uint32_t)0x00000006) /*!< PLLR division factor = 6 */
+#define RCC_PLLR_DIV8 ((uint32_t)0x00000008) /*!< PLLR division factor = 8 */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_PLL_Clock_Source PLL Clock Source
+ * @{
+ */
+#define RCC_PLLSOURCE_NONE ((uint32_t)0x00000000) /*!< No clock selected as PLL entry clock source */
+#define RCC_PLLSOURCE_MSI RCC_PLLCFGR_PLLSRC_MSI /*!< MSI clock selected as PLL entry clock source */
+#define RCC_PLLSOURCE_HSI RCC_PLLCFGR_PLLSRC_HSI /*!< HSI clock selected as PLL entry clock source */
+#define RCC_PLLSOURCE_HSE RCC_PLLCFGR_PLLSRC_HSE /*!< HSE clock selected as PLL entry clock source */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_PLL_Clock_Output PLL Clock Output
+ * @{
+ */
+#define RCC_PLL_SAI3CLK RCC_PLLCFGR_PLLPEN /*!< PLLSAI3CLK selection from main PLL */
+#define RCC_PLL_48M1CLK RCC_PLLCFGR_PLLQEN /*!< PLL48M1CLK selection from main PLL */
+#define RCC_PLL_SYSCLK RCC_PLLCFGR_PLLREN /*!< PLLCLK selection from main PLL */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_PLLSAI1_Clock_Output PLLSAI1 Clock Output
+ * @{
+ */
+#define RCC_PLLSAI1_SAI1CLK RCC_PLLSAI1CFGR_PLLSAI1PEN /*!< PLLSAI1CLK selection from PLLSAI1 */
+#define RCC_PLLSAI1_48M2CLK RCC_PLLSAI1CFGR_PLLSAI1QEN /*!< PLL48M2CLK selection from PLLSAI1 */
+#define RCC_PLLSAI1_ADC1CLK RCC_PLLSAI1CFGR_PLLSAI1REN /*!< PLLADC1CLK selection from PLLSAI1 */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_PLLSAI2_Clock_Output PLLSAI2 Clock Output
+ * @{
+ */
+#define RCC_PLLSAI2_SAI2CLK RCC_PLLSAI2CFGR_PLLSAI2PEN /*!< PLLSAI2CLK selection from PLLSAI2 */
+#define RCC_PLLSAI2_ADC2CLK RCC_PLLSAI2CFGR_PLLSAI2REN /*!< PLLADC2CLK selection from PLLSAI2 */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_MSI_Clock_Range MSI Clock Range
+ * @{
+ */
+#define RCC_MSIRANGE_0 RCC_CR_MSIRANGE_0 /*!< MSI = 100 KHz */
+#define RCC_MSIRANGE_1 RCC_CR_MSIRANGE_1 /*!< MSI = 200 KHz */
+#define RCC_MSIRANGE_2 RCC_CR_MSIRANGE_2 /*!< MSI = 400 KHz */
+#define RCC_MSIRANGE_3 RCC_CR_MSIRANGE_3 /*!< MSI = 800 KHz */
+#define RCC_MSIRANGE_4 RCC_CR_MSIRANGE_4 /*!< MSI = 1 MHz */
+#define RCC_MSIRANGE_5 RCC_CR_MSIRANGE_5 /*!< MSI = 2 MHz */
+#define RCC_MSIRANGE_6 RCC_CR_MSIRANGE_6 /*!< MSI = 4 MHz */
+#define RCC_MSIRANGE_7 RCC_CR_MSIRANGE_7 /*!< MSI = 8 MHz */
+#define RCC_MSIRANGE_8 RCC_CR_MSIRANGE_8 /*!< MSI = 16 MHz */
+#define RCC_MSIRANGE_9 RCC_CR_MSIRANGE_9 /*!< MSI = 24 MHz */
+#define RCC_MSIRANGE_10 RCC_CR_MSIRANGE_10 /*!< MSI = 32 MHz */
+#define RCC_MSIRANGE_11 RCC_CR_MSIRANGE_11 /*!< MSI = 48 MHz */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_System_Clock_Type System Clock Type
+ * @{
+ */
+#define RCC_CLOCKTYPE_SYSCLK ((uint32_t)0x00000001) /*!< SYSCLK to configure */
+#define RCC_CLOCKTYPE_HCLK ((uint32_t)0x00000002) /*!< HCLK to configure */
+#define RCC_CLOCKTYPE_PCLK1 ((uint32_t)0x00000004) /*!< PCLK1 to configure */
+#define RCC_CLOCKTYPE_PCLK2 ((uint32_t)0x00000008) /*!< PCLK2 to configure */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_System_Clock_Source System Clock Source
+ * @{
+ */
+#define RCC_SYSCLKSOURCE_MSI RCC_CFGR_SW_MSI /*!< MSI selection as system clock */
+#define RCC_SYSCLKSOURCE_HSI RCC_CFGR_SW_HSI /*!< HSI selection as system clock */
+#define RCC_SYSCLKSOURCE_HSE RCC_CFGR_SW_HSE /*!< HSE selection as system clock */
+#define RCC_SYSCLKSOURCE_PLLCLK RCC_CFGR_SW_PLL /*!< PLL selection as system clock */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_System_Clock_Source_Status System Clock Source Status
+ * @{
+ */
+#define RCC_SYSCLKSOURCE_STATUS_MSI RCC_CFGR_SWS_MSI /*!< MSI used as system clock */
+#define RCC_SYSCLKSOURCE_STATUS_HSI RCC_CFGR_SWS_HSI /*!< HSI used as system clock */
+#define RCC_SYSCLKSOURCE_STATUS_HSE RCC_CFGR_SWS_HSE /*!< HSE used as system clock */
+#define RCC_SYSCLKSOURCE_STATUS_PLLCLK RCC_CFGR_SWS_PLL /*!< PLL used as system clock */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_AHB_Clock_Source AHB Clock Source
+ * @{
+ */
+#define RCC_SYSCLK_DIV1 RCC_CFGR_HPRE_DIV1 /*!< SYSCLK not divided */
+#define RCC_SYSCLK_DIV2 RCC_CFGR_HPRE_DIV2 /*!< SYSCLK divided by 2 */
+#define RCC_SYSCLK_DIV4 RCC_CFGR_HPRE_DIV4 /*!< SYSCLK divided by 4 */
+#define RCC_SYSCLK_DIV8 RCC_CFGR_HPRE_DIV8 /*!< SYSCLK divided by 8 */
+#define RCC_SYSCLK_DIV16 RCC_CFGR_HPRE_DIV16 /*!< SYSCLK divided by 16 */
+#define RCC_SYSCLK_DIV64 RCC_CFGR_HPRE_DIV64 /*!< SYSCLK divided by 64 */
+#define RCC_SYSCLK_DIV128 RCC_CFGR_HPRE_DIV128 /*!< SYSCLK divided by 128 */
+#define RCC_SYSCLK_DIV256 RCC_CFGR_HPRE_DIV256 /*!< SYSCLK divided by 256 */
+#define RCC_SYSCLK_DIV512 RCC_CFGR_HPRE_DIV512 /*!< SYSCLK divided by 512 */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_APB1_APB2_Clock_Source APB1 APB2 Clock Source
+ * @{
+ */
+#define RCC_HCLK_DIV1 RCC_CFGR_PPRE1_DIV1 /*!< HCLK not divided */
+#define RCC_HCLK_DIV2 RCC_CFGR_PPRE1_DIV2 /*!< HCLK divided by 2 */
+#define RCC_HCLK_DIV4 RCC_CFGR_PPRE1_DIV4 /*!< HCLK divided by 4 */
+#define RCC_HCLK_DIV8 RCC_CFGR_PPRE1_DIV8 /*!< HCLK divided by 8 */
+#define RCC_HCLK_DIV16 RCC_CFGR_PPRE1_DIV16 /*!< HCLK divided by 16 */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_RTC_Clock_Source RTC Clock Source
+ * @{
+ */
+#define RCC_RTCCLKSOURCE_LSE RCC_BDCR_RTCSEL_0 /*!< LSE oscillator clock used as RTC clock */
+#define RCC_RTCCLKSOURCE_LSI RCC_BDCR_RTCSEL_1 /*!< LSI oscillator clock used as RTC clock */
+#define RCC_RTCCLKSOURCE_HSE_DIV32 RCC_BDCR_RTCSEL /*!< HSE oscillator clock divided by 32 used as RTC clock */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_MCO_Index MCO Index
+ * @{
+ */
+#define RCC_MCO1 ((uint32_t)0x00000000)
+#define RCC_MCO RCC_MCO1 /*!< MCO1 to be compliant with other families with 2 MCOs*/
+/**
+ * @}
+ */
+
+/** @defgroup RCC_MCO1_Clock_Source MCO1 Clock Source
+ * @{
+ */
+#define RCC_MCO1SOURCE_SYSCLK RCC_CFGR_MCOSEL_0 /*!< SYSCLK selection as MCO1 source */
+#define RCC_MCO1SOURCE_MSI RCC_CFGR_MCOSEL_1 /*!< MSI selection as MCO1 source */
+#define RCC_MCO1SOURCE_HSI (RCC_CFGR_MCOSEL_0| RCC_CFGR_MCOSEL_1) /*!< HSI selection as MCO1 source */
+#define RCC_MCO1SOURCE_HSE RCC_CFGR_MCOSEL_2 /*!< HSE selection as MCO1 source */
+#define RCC_MCO1SOURCE_PLLCLK (RCC_CFGR_MCOSEL_0|RCC_CFGR_MCOSEL_2) /*!< PLLCLK selection as MCO1 source */
+#define RCC_MCO1SOURCE_LSI (RCC_CFGR_MCOSEL_1|RCC_CFGR_MCOSEL_2) /*!< LSI selection as MCO1 source */
+#define RCC_MCO1SOURCE_LSE RCC_CFGR_MCOSEL /*!< LSE selection as MCO1 source */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_MCOx_Clock_Prescaler MCO1 Clock Prescaler
+ * @{
+ */
+#define RCC_MCODIV_1 RCC_CFGR_MCO_PRE_1 /*!< MCO not divided */
+#define RCC_MCODIV_2 RCC_CFGR_MCO_PRE_2 /*!< MCO divided by 2 */
+#define RCC_MCODIV_4 RCC_CFGR_MCO_PRE_4 /*!< MCO divided by 4 */
+#define RCC_MCODIV_8 RCC_CFGR_MCO_PRE_8 /*!< MCO divided by 8 */
+#define RCC_MCODIV_16 RCC_CFGR_MCO_PRE_16 /*!< MCO divided by 16 */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_Interrupt Interrupts
+ * @{
+ */
+#define RCC_IT_LSIRDY ((uint32_t)0x00000001) /*!< LSI Ready Interrupt flag */
+#define RCC_IT_LSERDY ((uint32_t)0x00000002) /*!< LSE Ready Interrupt flag */
+#define RCC_IT_MSIRDY ((uint32_t)0x00000004) /*!< MSI Ready Interrupt flag */
+#define RCC_IT_HSIRDY ((uint32_t)0x00000008) /*!< HSI Ready Interrupt flag */
+#define RCC_IT_HSERDY ((uint32_t)0x00000010) /*!< HSE Ready Interrupt flag */
+#define RCC_IT_PLLRDY ((uint32_t)0x00000020) /*!< PLL Ready Interrupt flag */
+#define RCC_IT_PLLSAI1RDY ((uint32_t)0x00000040) /*!< PLLSAI1 Ready Interrupt flag */
+#define RCC_IT_PLLSAI2RDY ((uint32_t)0x00000080) /*!< PLLSAI2 Ready Interrupt flag */
+#define RCC_IT_CSS ((uint32_t)0x00000100) /*!< Clock Security System Interrupt flag */
+#define RCC_IT_LSECSS ((uint32_t)0x00000200) /*!< LSE Clock Security System Interrupt flag */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_Flag Flags
+ * Elements values convention: 0XXYYYYYb
+ * - YYYYY : Flag position in the register
+ * - 0XX : Register index
+ * - 01: CR register
+ * - 10: BDCR register
+ * - 11: CSR register
+ * @{
+ */
+/* Flags in the CR register */
+#define RCC_FLAG_MSIRDY ((uint8_t)((CR_REG_INDEX << 5) | POSITION_VAL(RCC_CR_MSIRDY))) /*!< MSI Ready flag */
+#define RCC_FLAG_HSIRDY ((uint8_t)((CR_REG_INDEX << 5) | POSITION_VAL(RCC_CR_HSIRDY))) /*!< HSI Ready flag */
+#define RCC_FLAG_HSERDY ((uint8_t)((CR_REG_INDEX << 5) | POSITION_VAL(RCC_CR_HSERDY))) /*!< HSE Ready flag */
+#define RCC_FLAG_PLLRDY ((uint8_t)((CR_REG_INDEX << 5) | POSITION_VAL(RCC_CR_PLLRDY))) /*!< PLL Ready flag */
+#define RCC_FLAG_PLLSAI1RDY ((uint8_t)((CR_REG_INDEX << 5) | POSITION_VAL(RCC_CR_PLLSAI1RDY))) /*!< PLLSAI1 Ready flag */
+#define RCC_FLAG_PLLSAI2RDY ((uint8_t)((CR_REG_INDEX << 5) | POSITION_VAL(RCC_CR_PLLSAI2RDY))) /*!< PLLSAI2 Ready flag */
+
+/* Flags in the BDCR register */
+#define RCC_FLAG_LSERDY ((uint8_t)((BDCR_REG_INDEX << 5) | POSITION_VAL(RCC_BDCR_LSERDY))) /*!< LSE Ready flag */
+#define RCC_FLAG_LSECSSD ((uint8_t)((BDCR_REG_INDEX << 5) | POSITION_VAL(RCC_BDCR_LSECSSD))) /*!< LSE Clock Security System Interrupt flag */
+
+/* Flags in the CSR register */
+#define RCC_FLAG_LSIRDY ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_LSIRDY))) /*!< LSI Ready flag */
+#define RCC_FLAG_RMVF ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_RMVF))) /*!< Remove reset flag */
+#define RCC_FLAG_FWRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_FWRSTF))) /*!< Firewall reset flag */
+#define RCC_FLAG_OBLRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_OBLRSTF))) /*!< Option Byte Loader reset flag */
+#define RCC_FLAG_PINRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_PINRSTF))) /*!< PIN reset flag */
+#define RCC_FLAG_BORRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_BORRSTF))) /*!< BOR reset flag */
+#define RCC_FLAG_SFTRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_SFTRSTF))) /*!< Software Reset flag */
+#define RCC_FLAG_IWDGRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_IWDGRSTF))) /*!< Independent Watchdog reset flag */
+#define RCC_FLAG_WWDGRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_WWDGRSTF))) /*!< Window watchdog reset flag */
+#define RCC_FLAG_LPWRRST ((uint8_t)((CSR_REG_INDEX << 5) | POSITION_VAL(RCC_CSR_LPWRRSTF))) /*!< Low-Power reset flag */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_LSEDrive_Config LSE Drive Config
+ * @{
+ */
+#define RCC_LSEDRIVE_LOW ((uint32_t)0x00000000) /*!< LSE low drive capability */
+#define RCC_LSEDRIVE_MEDIUMLOW RCC_BDCR_LSEDRV_1 /*!< LSE medium low drive capability */
+ /* Workaround implementation on medium low */
+#define RCC_LSEDRIVE_MEDIUMHIGH RCC_BDCR_LSEDRV_0 /*!< LSE medium high drive capability */
+ /* Workaround implementation on medium high */
+#define RCC_LSEDRIVE_HIGH RCC_BDCR_LSEDRV /*!< LSE high drive capability */
+/**
+ * @}
+ */
+
+/** @defgroup RCC_Stop_WakeUpClock Wake-Up from STOP Clock
+ * @{
+ */
+#define RCC_STOP_WAKEUPCLOCK_MSI ((uint32_t)0x00000000) /*!< MSI selection after wake-up from STOP */
+#define RCC_STOP_WAKEUPCLOCK_HSI RCC_CFGR_STOPWUCK /*!< HSI selection after wake-up from STOP */
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/* Exported macros -----------------------------------------------------------*/
+
+/** @defgroup RCC_Exported_Macros RCC Exported Macros
+ * @{
+ */
+
+/** @defgroup RCC_AHB1_Peripheral_Clock_Enable_Disable AHB1 Peripheral Clock Enable Disable
+ * @brief Enable or disable the AHB1 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+
+#define __HAL_RCC_DMA1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA1EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA1EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_DMA2_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA2EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA2EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_FLASH_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_FLASHEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_FLASHEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_CRC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_TSC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB1ENR, RCC_AHB1ENR_TSCEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_TSCEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_DMA1_CLK_DISABLE() CLEAR_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA1EN)
+
+#define __HAL_RCC_DMA2_CLK_DISABLE() CLEAR_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA2EN)
+
+#define __HAL_RCC_FLASH_CLK_DISABLE() CLEAR_BIT(RCC->AHB1ENR, RCC_AHB1ENR_FLASHEN)
+
+#define __HAL_RCC_CRC_CLK_DISABLE() CLEAR_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN)
+
+#define __HAL_RCC_TSC_CLK_DISABLE() CLEAR_BIT(RCC->AHB1ENR, RCC_AHB1ENR_TSCEN)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_AHB2_Clock_Enable_Disable AHB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+
+#define __HAL_RCC_GPIOA_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOAEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOAEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_GPIOB_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOBEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOBEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_GPIOC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOCEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOCEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_GPIOD_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIODEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIODEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_GPIOE_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOEEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOEEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_GPIOF_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOFEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOFEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_GPIOG_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOGEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOGEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_GPIOH_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOHEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOHEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_ADC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_ADCEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_ADCEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_RNG_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_GPIOA_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOAEN)
+
+#define __HAL_RCC_GPIOB_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOBEN)
+
+#define __HAL_RCC_GPIOC_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOCEN)
+
+#define __HAL_RCC_GPIOD_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIODEN)
+
+#define __HAL_RCC_GPIOE_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOEEN)
+
+#define __HAL_RCC_GPIOF_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOFEN)
+
+#define __HAL_RCC_GPIOG_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOGEN)
+
+#define __HAL_RCC_GPIOH_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOHEN)
+
+#define __HAL_RCC_ADC_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_ADCEN)
+
+#define __HAL_RCC_RNG_CLK_DISABLE() CLEAR_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_AHB3_Clock_Enable_Disable AHB3 Peripheral Clock Enable Disable
+ * @brief Enable or disable the AHB3 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+
+#define __HAL_RCC_FMC_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_QSPI_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_FMC_CLK_DISABLE() CLEAR_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN)
+
+#define __HAL_RCC_QSPI_CLK_DISABLE() CLEAR_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_APB1_Clock_Enable_Disable APB1 Peripheral Clock Enable Disable
+ * @brief Enable or disable the APB1 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+
+#define __HAL_RCC_TIM2_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM2EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM2EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_TIM3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM3EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM3EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_TIM4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM4EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM4EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_TIM5_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM5EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM5EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_TIM6_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM6EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM6EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_TIM7_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM7EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM7EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_WWDG_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_WWDGEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_WWDGEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_SPI2_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI2EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI2EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_SPI3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI3EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI3EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_USART2_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART2EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART2EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_USART3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART3EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART3EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_UART4_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART4EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART4EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_UART5_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART5EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART5EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_I2C1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C1EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C1EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_I2C2_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C2EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C2EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_I2C3_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C3EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C3EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_CAN1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_CAN1EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_CAN1EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_PWR_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_PWREN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_PWREN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_DAC1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_DAC1EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_DAC1EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_OPAMP_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_OPAMPEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_OPAMPEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_LPTIM1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LPTIM1EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LPTIM1EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_LPUART1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPUART1EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPUART1EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_SWPMI1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR2, RCC_APB1ENR2_SWPMI1EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_SWPMI1EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_LPTIM2_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPTIM2EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPTIM2EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_TIM2_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM2EN)
+
+#define __HAL_RCC_TIM3_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM3EN)
+
+#define __HAL_RCC_TIM4_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM4EN)
+
+#define __HAL_RCC_TIM5_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM5EN)
+
+#define __HAL_RCC_TIM6_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM6EN)
+
+#define __HAL_RCC_TIM7_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM7EN)
+
+#define __HAL_RCC_WWDG_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_WWDGEN)
+
+#define __HAL_RCC_SPI2_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI2EN)
+
+#define __HAL_RCC_SPI3_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI3EN)
+
+#define __HAL_RCC_USART2_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART2EN)
+
+#define __HAL_RCC_USART3_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART3EN)
+
+#define __HAL_RCC_UART4_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART4EN)
+
+#define __HAL_RCC_UART5_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART5EN)
+
+#define __HAL_RCC_I2C1_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C1EN)
+
+#define __HAL_RCC_I2C2_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C2EN)
+
+#define __HAL_RCC_I2C3_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C3EN)
+
+#define __HAL_RCC_CAN1_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_CAN1EN)
+
+#define __HAL_RCC_PWR_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_PWREN)
+
+#define __HAL_RCC_DAC1_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_DAC1EN)
+
+#define __HAL_RCC_OPAMP_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_OPAMPEN)
+
+#define __HAL_RCC_LPTIM1_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LPTIM1EN)
+
+#define __HAL_RCC_LPUART1_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPUART1EN)
+
+#define __HAL_RCC_SWPMI1_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR2, RCC_APB1ENR2_SWPMI1EN)
+
+#define __HAL_RCC_LPTIM2_CLK_DISABLE() CLEAR_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPTIM2EN)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_APB2_Clock_Enable_Disable APB2 Peripheral Clock Enable Disable
+ * @brief Enable or disable the APB2 peripheral clock.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+
+#define __HAL_RCC_SYSCFG_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_FIREWALL_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_FWEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_FWEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_SDMMC1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SDMMC1EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDMMC1EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_TIM1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_SPI1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_TIM8_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_USART1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+
+#define __HAL_RCC_TIM15_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM15EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM15EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_TIM16_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM16EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM16EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_TIM17_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM17EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM17EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_SAI1_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI1EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI1EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_SAI2_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI2EN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI2EN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_DFSDM_CLK_ENABLE() do { \
+ __IO uint32_t tmpreg; \
+ SET_BIT(RCC->APB2ENR, RCC_APB2ENR_DFSDMEN); \
+ /* Delay after an RCC peripheral clock enabling */ \
+ tmpreg = READ_BIT(RCC->APB2ENR, RCC_APB2ENR_DFSDMEN); \
+ UNUSED(tmpreg); \
+ } while(0)
+
+#define __HAL_RCC_SYSCFG_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN)
+
+#define __HAL_RCC_SDMMC1_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_SDMMC1EN)
+
+#define __HAL_RCC_TIM1_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN)
+
+#define __HAL_RCC_SPI1_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN)
+
+#define __HAL_RCC_TIM8_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN)
+
+#define __HAL_RCC_USART1_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN)
+
+#define __HAL_RCC_TIM15_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM15EN)
+
+#define __HAL_RCC_TIM16_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM16EN)
+
+#define __HAL_RCC_TIM17_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM17EN)
+
+#define __HAL_RCC_SAI1_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI1EN)
+
+#define __HAL_RCC_SAI2_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI2EN)
+
+#define __HAL_RCC_DFSDM_CLK_DISABLE() CLEAR_BIT(RCC->APB2ENR, RCC_APB2ENR_DFSDMEN)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_AHB1_Peripheral_Clock_Enable_Disable_Status AHB1 Peripheral Clock Enabled or Disabled Status
+ * @brief Check whether the AHB1 peripheral clock is enabled or not.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+
+#define __HAL_RCC_DMA1_IS_CLK_ENABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA1EN) != RESET)
+
+#define __HAL_RCC_DMA2_IS_CLK_ENABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA2EN) != RESET)
+
+#define __HAL_RCC_FLASH_IS_CLK_ENABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_FLASHEN) != RESET)
+
+#define __HAL_RCC_CRC_IS_CLK_ENABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN) != RESET)
+
+#define __HAL_RCC_TSC_IS_CLK_ENABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_TSCEN) != RESET)
+
+#define __HAL_RCC_DMA1_IS_CLK_DISABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA1EN) == RESET)
+
+#define __HAL_RCC_DMA2_IS_CLK_DISABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_DMA2EN) == RESET)
+
+#define __HAL_RCC_FLASH_IS_CLK_DISABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_FLASHEN) == RESET)
+
+#define __HAL_RCC_CRC_IS_CLK_DISABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_CRCEN) == RESET)
+
+#define __HAL_RCC_TSC_IS_CLK_DISABLED() (READ_BIT(RCC->AHB1ENR, RCC_AHB1ENR_TSCEN) == RESET)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_AHB2_Clock_Enable_Disable_Status AHB2 Peripheral Clock Enabled or Disabled Status
+ * @brief Check whether the AHB2 peripheral clock is enabled or not.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+
+#define __HAL_RCC_GPIOA_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOAEN) != RESET)
+
+#define __HAL_RCC_GPIOB_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOCEN) != RESET)
+
+#define __HAL_RCC_GPIOC_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOCEN) != RESET)
+
+#define __HAL_RCC_GPIOD_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIODEN) != RESET)
+
+#define __HAL_RCC_GPIOE_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOEEN) != RESET)
+
+#define __HAL_RCC_GPIOF_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOFEN) != RESET)
+
+#define __HAL_RCC_GPIOG_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOGEN) != RESET)
+
+#define __HAL_RCC_GPIOH_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOHEN) != RESET)
+
+#define __HAL_RCC_ADC_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_ADCEN) != RESET)
+
+#define __HAL_RCC_RNG_IS_CLK_ENABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN) != RESET)
+
+#define __HAL_RCC_GPIOA_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOAEN) == RESET)
+
+#define __HAL_RCC_GPIOB_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOBEN) == RESET)
+
+#define __HAL_RCC_GPIOC_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOCEN) == RESET)
+
+#define __HAL_RCC_GPIOD_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIODEN) == RESET)
+
+#define __HAL_RCC_GPIOE_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOEEN) == RESET)
+
+#define __HAL_RCC_GPIOF_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOFEN) == RESET)
+
+#define __HAL_RCC_GPIOG_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOGEN) == RESET)
+
+#define __HAL_RCC_GPIOH_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_GPIOHEN) == RESET)
+
+#define __HAL_RCC_ADC_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_ADCEN) == RESET)
+
+#define __HAL_RCC_RNG_IS_CLK_DISABLED() (READ_BIT(RCC->AHB2ENR, RCC_AHB2ENR_RNGEN) == RESET)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_AHB3_Clock_Enable_Disable_Status AHB3 Peripheral Clock Enabled or Disabled Status
+ * @brief Check whether the AHB3 peripheral clock is enabled or not.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+
+#define __HAL_RCC_FMC_IS_CLK_ENABLED() (READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN) != RESET)
+
+#define __HAL_RCC_QSPI_IS_CLK_ENABLED() (READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN) != RESET)
+
+#define __HAL_RCC_FMC_IS_CLK_DISABLED() (READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_FMCEN) == RESET)
+
+#define __HAL_RCC_QSPI_IS_CLK_DISABLED() (READ_BIT(RCC->AHB3ENR, RCC_AHB3ENR_QSPIEN) == RESET)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_APB1_Clock_Enable_Disable_Status APB1 Peripheral Clock Enabled or Disabled Status
+ * @brief Check whether the APB1 peripheral clock is enabled or not.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+
+#define __HAL_RCC_TIM2_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM2EN) != RESET)
+
+#define __HAL_RCC_TIM3_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM3EN) != RESET)
+
+#define __HAL_RCC_TIM4_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM4EN) != RESET)
+
+#define __HAL_RCC_TIM5_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM5EN) != RESET)
+
+#define __HAL_RCC_TIM6_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM6EN) != RESET)
+
+#define __HAL_RCC_TIM7_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM7EN) != RESET)
+
+#define __HAL_RCC_WWDG_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_WWDGEN) != RESET)
+
+#define __HAL_RCC_SPI2_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI2EN) != RESET)
+
+#define __HAL_RCC_SPI3_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI3EN) != RESET)
+
+#define __HAL_RCC_USART2_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART2EN) != RESET)
+
+#define __HAL_RCC_USART3_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART3EN) != RESET)
+
+#define __HAL_RCC_UART4_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART4EN) != RESET)
+
+#define __HAL_RCC_UART5_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART5EN) != RESET)
+
+#define __HAL_RCC_I2C1_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C1EN) != RESET)
+
+#define __HAL_RCC_I2C2_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C2EN) != RESET)
+
+#define __HAL_RCC_I2C3_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C3EN) != RESET)
+
+#define __HAL_RCC_CAN1_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_CAN1EN) != RESET)
+
+#define __HAL_RCC_PWR_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_PWREN) != RESET)
+
+#define __HAL_RCC_DAC1_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_DAC1EN) != RESET)
+
+#define __HAL_RCC_OPAMP_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_OPAMPEN) != RESET)
+
+#define __HAL_RCC_LPTIM1_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LPTIM1EN) != RESET)
+
+#define __HAL_RCC_LPUART1_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPUART1EN) != RESET)
+
+#define __HAL_RCC_SWPMI1_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_SWPMI1EN) != RESET)
+
+#define __HAL_RCC_LPTIM2_IS_CLK_ENABLED() (READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPTIM2EN) != RESET)
+
+#define __HAL_RCC_TIM2_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM2EN) == RESET)
+
+#define __HAL_RCC_TIM3_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM3EN) == RESET)
+
+#define __HAL_RCC_TIM4_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM4EN) == RESET)
+
+#define __HAL_RCC_TIM5_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM5EN) == RESET)
+
+#define __HAL_RCC_TIM6_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM6EN) == RESET)
+
+#define __HAL_RCC_TIM7_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_TIM7EN) == RESET)
+
+#define __HAL_RCC_WWDG_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_WWDGEN) == RESET)
+
+#define __HAL_RCC_SPI2_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI2EN) == RESET)
+
+#define __HAL_RCC_SPI3_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_SPI3EN) == RESET)
+
+#define __HAL_RCC_USART2_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART2EN) == RESET)
+
+#define __HAL_RCC_USART3_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_USART3EN) == RESET)
+
+#define __HAL_RCC_UART4_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART4EN) == RESET)
+
+#define __HAL_RCC_UART5_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_UART5EN) == RESET)
+
+#define __HAL_RCC_I2C1_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C1EN) == RESET)
+
+#define __HAL_RCC_I2C2_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C2EN) == RESET)
+
+#define __HAL_RCC_I2C3_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_I2C3EN) == RESET)
+
+#define __HAL_RCC_CAN1_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_CAN1EN) == RESET)
+
+#define __HAL_RCC_PWR_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_PWREN) == RESET)
+
+#define __HAL_RCC_DAC1_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_DAC1EN) == RESET)
+
+#define __HAL_RCC_OPAMP_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_OPAMPEN) == RESET)
+
+#define __HAL_RCC_LPTIM1_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR1, RCC_APB1ENR1_LPTIM1EN) == RESET)
+
+#define __HAL_RCC_LPUART1_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPUART1EN) == RESET)
+
+#define __HAL_RCC_SWPMI1_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_SWPMI1EN) == RESET)
+
+#define __HAL_RCC_LPTIM2_IS_CLK_DISABLED() (READ_BIT(RCC->APB1ENR2, RCC_APB1ENR2_LPTIM2EN) == RESET)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_APB2_Clock_Enable_Disable_Status APB2 Peripheral Clock Enabled or Disabled Status
+ * @brief Check whether the APB2 peripheral clock is enabled or not.
+ * @note After reset, the peripheral clock (used for registers read/write access)
+ * is disabled and the application software has to enable this clock before
+ * using it.
+ * @{
+ */
+
+#define __HAL_RCC_SYSCFG_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN) != RESET)
+
+#define __HAL_RCC_FIREWALL_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_FWEN) != RESET)
+
+#define __HAL_RCC_SDMMC1_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDMMC1EN) != RESET)
+
+#define __HAL_RCC_TIM1_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN) != RESET)
+
+#define __HAL_RCC_SPI1_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN) != RESET)
+
+#define __HAL_RCC_TIM8_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN) != RESET)
+
+#define __HAL_RCC_USART1_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN) != RESET)
+
+#define __HAL_RCC_TIM15_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM15EN) != RESET)
+
+#define __HAL_RCC_TIM16_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM16EN) != RESET)
+
+#define __HAL_RCC_TIM17_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM17EN) != RESET)
+
+#define __HAL_RCC_SAI1_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI1EN) != RESET)
+
+#define __HAL_RCC_SAI2_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI2EN) != RESET)
+
+#define __HAL_RCC_DFSDM_IS_CLK_ENABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_DFSDMEN) != RESET)
+
+#define __HAL_RCC_SYSCFG_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SYSCFGEN) == RESET)
+
+#define __HAL_RCC_SDMMC1_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SDMMC1EN) == RESET)
+
+#define __HAL_RCC_TIM1_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM1EN) == RESET)
+
+#define __HAL_RCC_SPI1_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SPI1EN) == RESET)
+
+#define __HAL_RCC_TIM8_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM8EN) == RESET)
+
+#define __HAL_RCC_USART1_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_USART1EN) == RESET)
+
+#define __HAL_RCC_TIM15_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM15EN) == RESET)
+
+#define __HAL_RCC_TIM16_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM16EN) == RESET)
+
+#define __HAL_RCC_TIM17_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_TIM17EN) == RESET)
+
+#define __HAL_RCC_SAI1_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI1EN) == RESET)
+
+#define __HAL_RCC_SAI2_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_SAI2EN) == RESET)
+
+#define __HAL_RCC_DFSDM_IS_CLK_DISABLED() (READ_BIT(RCC->APB2ENR, RCC_APB2ENR_DFSDMEN) == RESET)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_AHB1_Force_Release_Reset AHB1 Peripheral Force Release Reset
+ * @brief Force or release AHB1 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB1_FORCE_RESET() WRITE_REG(RCC->AHB1RSTR, 0xFFFFFFFF)
+
+#define __HAL_RCC_DMA1_FORCE_RESET() SET_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_DMA1RST)
+
+#define __HAL_RCC_DMA2_FORCE_RESET() SET_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_DMA2RST)
+
+#define __HAL_RCC_FLASH_FORCE_RESET() SET_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_FLASHRST)
+
+#define __HAL_RCC_CRC_FORCE_RESET() SET_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_CRCRST)
+
+#define __HAL_RCC_TSC_FORCE_RESET() SET_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_TSCRST)
+
+#define __HAL_RCC_AHB1_RELEASE_RESET() WRITE_REG(RCC->AHB1RSTR, 0x00000000)
+
+#define __HAL_RCC_DMA1_RELEASE_RESET() CLEAR_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_DMA1RST)
+
+#define __HAL_RCC_DMA2_RELEASE_RESET() CLEAR_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_DMA2RST)
+
+#define __HAL_RCC_FLASH_RELEASE_RESET() CLEAR_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_FLASHRST)
+
+#define __HAL_RCC_CRC_RELEASE_RESET() CLEAR_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_CRCRST)
+
+#define __HAL_RCC_TSC_RELEASE_RESET() CLEAR_BIT(RCC->AHB1RSTR, RCC_AHB1RSTR_TSCRST)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_AHB2_Force_Release_Reset AHB2 Peripheral Force Release Reset
+ * @brief Force or release AHB2 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB2_FORCE_RESET() WRITE_REG(RCC->AHB2RSTR, 0xFFFFFFFF)
+
+#define __HAL_RCC_GPIOA_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOARST)
+
+#define __HAL_RCC_GPIOB_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOBRST)
+
+#define __HAL_RCC_GPIOC_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOCRST)
+
+#define __HAL_RCC_GPIOD_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIODRST)
+
+#define __HAL_RCC_GPIOE_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOERST)
+
+#define __HAL_RCC_GPIOF_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOFRST)
+
+#define __HAL_RCC_GPIOG_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOGRST)
+
+#define __HAL_RCC_GPIOH_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOHRST)
+
+#define __HAL_RCC_ADC_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_ADCRST)
+
+#define __HAL_RCC_RNG_FORCE_RESET() SET_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_RNGRST)
+
+#define __HAL_RCC_AHB2_RELEASE_RESET() WRITE_REG(RCC->AHB2RSTR, 0x00000000)
+
+#define __HAL_RCC_GPIOA_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOARST)
+
+#define __HAL_RCC_GPIOB_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOBRST)
+
+#define __HAL_RCC_GPIOC_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOCRST)
+
+#define __HAL_RCC_GPIOD_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIODRST)
+
+#define __HAL_RCC_GPIOE_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOERST)
+
+#define __HAL_RCC_GPIOF_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOFRST)
+
+#define __HAL_RCC_GPIOG_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOGRST)
+
+#define __HAL_RCC_GPIOH_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_GPIOHRST)
+
+#define __HAL_RCC_ADC_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_ADCRST)
+
+#define __HAL_RCC_RNG_RELEASE_RESET() CLEAR_BIT(RCC->AHB2RSTR, RCC_AHB2RSTR_RNGRST)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_AHB3_Force_Release_Reset AHB3 Peripheral Force Release Reset
+ * @brief Force or release AHB3 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_AHB3_FORCE_RESET() WRITE_REG(RCC->AHB3RSTR, 0xFFFFFFFF)
+
+#define __HAL_RCC_FMC_FORCE_RESET() SET_BIT(RCC->AHB3RSTR, RCC_AHB3RSTR_FMCRST)
+
+#define __HAL_RCC_QSPI_FORCE_RESET() SET_BIT(RCC->AHB3RSTR, RCC_AHB3RSTR_QSPIRST)
+
+#define __HAL_RCC_AHB3_RELEASE_RESET() WRITE_REG(RCC->AHB3RSTR, 0x00000000)
+
+#define __HAL_RCC_FMC_RELEASE_RESET() CLEAR_BIT(RCC->AHB3RSTR, RCC_AHB3RSTR_FMCRST)
+
+#define __HAL_RCC_QSPI_RELEASE_RESET() CLEAR_BIT(RCC->AHB3RSTR, RCC_AHB3RSTR_QSPIRST)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_APB1_Force_Release_Reset APB1 Peripheral Force Release Reset
+ * @brief Force or release APB1 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_APB1_FORCE_RESET() WRITE_REG(RCC->APB1RSTR1, 0xFFFFFFFF)
+
+#define __HAL_RCC_TIM2_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM2RST)
+
+#define __HAL_RCC_TIM3_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM3RST)
+
+#define __HAL_RCC_TIM4_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM4RST)
+
+#define __HAL_RCC_TIM5_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM5RST)
+
+#define __HAL_RCC_TIM6_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM6RST)
+
+#define __HAL_RCC_TIM7_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM7RST)
+
+#define __HAL_RCC_SPI2_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_SPI2RST)
+
+#define __HAL_RCC_SPI3_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_SPI3RST)
+
+#define __HAL_RCC_USART2_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_USART2RST)
+
+#define __HAL_RCC_USART3_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_USART3RST)
+
+#define __HAL_RCC_UART4_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_UART4RST)
+
+#define __HAL_RCC_UART5_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_UART5RST)
+
+#define __HAL_RCC_I2C1_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_I2C1RST)
+
+#define __HAL_RCC_I2C2_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_I2C2RST)
+
+#define __HAL_RCC_I2C3_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_I2C3RST)
+
+#define __HAL_RCC_CAN1_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_CAN1RST)
+
+#define __HAL_RCC_PWR_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_PWRRST)
+
+#define __HAL_RCC_DAC1_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_DAC1RST)
+
+#define __HAL_RCC_OPAMP_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_OPAMPRST)
+
+#define __HAL_RCC_LPTIM1_FORCE_RESET() SET_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_LPTIM1RST)
+
+#define __HAL_RCC_LPUART1_FORCE_RESET() SET_BIT(RCC->APB1RSTR2, RCC_APB1RSTR2_LPUART1RST)
+
+#define __HAL_RCC_SWPMI1_FORCE_RESET() SET_BIT(RCC->APB1RSTR2, RCC_APB1RSTR2_SWPMI1RST)
+
+#define __HAL_RCC_LPTIM2_FORCE_RESET() SET_BIT(RCC->APB1RSTR2, RCC_APB1RSTR2_LPTIM2RST)
+
+#define __HAL_RCC_APB1_RELEASE_RESET() WRITE_REG(RCC->APB1RSTR1, 0x00000000)
+
+#define __HAL_RCC_TIM2_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM2RST)
+
+#define __HAL_RCC_TIM3_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM3RST)
+
+#define __HAL_RCC_TIM4_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM4RST)
+
+#define __HAL_RCC_TIM5_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM5RST)
+
+#define __HAL_RCC_TIM6_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM6RST)
+
+#define __HAL_RCC_TIM7_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_TIM7RST)
+
+#define __HAL_RCC_SPI2_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_SPI2RST)
+
+#define __HAL_RCC_SPI3_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_SPI3RST)
+
+#define __HAL_RCC_USART2_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_USART2RST)
+
+#define __HAL_RCC_USART3_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_USART3RST)
+
+#define __HAL_RCC_UART4_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_UART4RST)
+
+#define __HAL_RCC_UART5_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_UART5RST)
+
+#define __HAL_RCC_I2C1_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_I2C1RST)
+
+#define __HAL_RCC_I2C2_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_I2C2RST)
+
+#define __HAL_RCC_I2C3_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_I2C3RST)
+
+#define __HAL_RCC_CAN1_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_CAN1RST)
+
+#define __HAL_RCC_PWR_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_PWRRST)
+
+#define __HAL_RCC_DAC1_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_DAC1RST)
+
+#define __HAL_RCC_OPAMP_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_OPAMPRST)
+
+#define __HAL_RCC_LPTIM1_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR1, RCC_APB1RSTR1_LPTIM1RST)
+
+#define __HAL_RCC_LPUART1_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR2, RCC_APB1RSTR2_LPUART1RST)
+
+#define __HAL_RCC_SWPMI1_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR2, RCC_APB1RSTR2_SWPMI1RST)
+
+#define __HAL_RCC_LPTIM2_RELEASE_RESET() CLEAR_BIT(RCC->APB1RSTR2, RCC_APB1RSTR2_LPTIM2RST)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_APB2_Force_Release_Reset APB2 Peripheral Force Release Reset
+ * @brief Force or release APB2 peripheral reset.
+ * @{
+ */
+#define __HAL_RCC_APB2_FORCE_RESET() WRITE_REG(RCC->APB2RSTR, 0xFFFFFFFF)
+
+#define __HAL_RCC_SYSCFG_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SYSCFGRST)
+
+#define __HAL_RCC_SDMMC1_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SDMMC1RST)
+
+#define __HAL_RCC_TIM1_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM1RST)
+
+#define __HAL_RCC_SPI1_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SPI1RST)
+
+#define __HAL_RCC_TIM8_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM8RST)
+
+#define __HAL_RCC_USART1_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_USART1RST)
+
+#define __HAL_RCC_TIM15_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM15RST)
+
+#define __HAL_RCC_TIM16_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM16RST)
+
+#define __HAL_RCC_TIM17_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM17RST)
+
+#define __HAL_RCC_SAI1_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SAI1RST)
+
+#define __HAL_RCC_SAI2_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SAI2RST)
+
+#define __HAL_RCC_DFSDM_FORCE_RESET() SET_BIT(RCC->APB2RSTR, RCC_APB2RSTR_DFSDMRST)
+
+#define __HAL_RCC_APB2_RELEASE_RESET() WRITE_REG(RCC->APB2RSTR, 0x00000000)
+
+#define __HAL_RCC_SYSCFG_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SYSCFGRST)
+
+#define __HAL_RCC_SDMMC1_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SDMMC1RST)
+
+#define __HAL_RCC_TIM1_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM1RST)
+
+#define __HAL_RCC_SPI1_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SPI1RST)
+
+#define __HAL_RCC_TIM8_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM8RST)
+
+#define __HAL_RCC_USART1_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_USART1RST)
+
+#define __HAL_RCC_TIM15_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM15RST)
+
+#define __HAL_RCC_TIM16_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM16RST)
+
+#define __HAL_RCC_TIM17_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_TIM17RST)
+
+#define __HAL_RCC_SAI1_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SAI1RST)
+
+#define __HAL_RCC_SAI2_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_SAI2RST)
+
+#define __HAL_RCC_DFSDM_RELEASE_RESET() CLEAR_BIT(RCC->APB2RSTR, RCC_APB2RSTR_DFSDMRST)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_AHB1_Clock_Sleep_Enable_Disable AHB1 Peripheral Clock Sleep Enable Disable
+ * @brief Enable or disable the AHB1 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+
+#define __HAL_RCC_DMA1_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA1SMEN)
+
+#define __HAL_RCC_DMA2_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA2SMEN)
+
+#define __HAL_RCC_FLASH_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_FLASHSMEN)
+
+#define __HAL_RCC_SRAM1_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_SRAM1SMEN)
+
+#define __HAL_RCC_CRC_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_CRCSMEN)
+
+#define __HAL_RCC_TSC_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_TSCSMEN)
+
+#define __HAL_RCC_DMA1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA1SMEN)
+
+#define __HAL_RCC_DMA2_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA2SMEN)
+
+#define __HAL_RCC_FLASH_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_FLASHSMEN)
+
+#define __HAL_RCC_SRAM1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_SRAM1SMEN)
+
+#define __HAL_RCC_CRC_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_CRCSMEN)
+
+#define __HAL_RCC_TSC_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_TSCSMEN)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_AHB2_Clock_Sleep_Enable_Disable AHB2 Peripheral Clock Sleep Enable Disable
+ * @brief Enable or disable the AHB2 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+
+#define __HAL_RCC_GPIOA_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOASMEN)
+
+#define __HAL_RCC_GPIOB_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOBSMEN)
+
+#define __HAL_RCC_GPIOC_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOCSMEN)
+
+#define __HAL_RCC_GPIOD_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIODSMEN)
+
+#define __HAL_RCC_GPIOE_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOESMEN)
+
+#define __HAL_RCC_GPIOF_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOFSMEN)
+
+#define __HAL_RCC_GPIOG_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOGSMEN)
+
+#define __HAL_RCC_GPIOH_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOHSMEN)
+
+#define __HAL_RCC_SRAM2_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_SRAM2SMEN)
+
+#define __HAL_RCC_ADC_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_ADCSMEN)
+
+#define __HAL_RCC_RNG_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_RNGSMEN)
+
+#define __HAL_RCC_GPIOA_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOASMEN)
+
+#define __HAL_RCC_GPIOB_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOBSMEN)
+
+#define __HAL_RCC_GPIOC_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOCSMEN)
+
+#define __HAL_RCC_GPIOD_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIODSMEN)
+
+#define __HAL_RCC_GPIOE_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOESMEN)
+
+#define __HAL_RCC_GPIOF_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOFSMEN)
+
+#define __HAL_RCC_GPIOG_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOGSMEN)
+
+#define __HAL_RCC_GPIOH_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOHSMEN)
+
+#define __HAL_RCC_ADC_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_ADCSMEN)
+
+#define __HAL_RCC_SRAM2_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_SRAM2SMEN)
+
+#define __HAL_RCC_RNG_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_RNGSMEN)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_AHB3_Clock_Sleep_Enable_Disable AHB3 Peripheral Clock Sleep Enable Disable
+ * @brief Enable or disable the AHB3 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+
+#define __HAL_RCC_QSPI_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_QSPISMEN)
+
+#define __HAL_RCC_FMC_CLK_SLEEP_ENABLE() SET_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_FMCSMEN)
+
+#define __HAL_RCC_QSPI_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_QSPISMEN)
+
+#define __HAL_RCC_FMC_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_FMCSMEN)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_APB1_Clock_Sleep_Enable_Disable APB1 Peripheral Clock Sleep Enable Disable
+ * @brief Enable or disable the APB1 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+
+#define __HAL_RCC_TIM2_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM2SMEN)
+
+#define __HAL_RCC_TIM3_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM3SMEN)
+
+#define __HAL_RCC_TIM4_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM4SMEN)
+
+#define __HAL_RCC_TIM5_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM5SMEN)
+
+#define __HAL_RCC_TIM6_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM6SMEN)
+
+#define __HAL_RCC_TIM7_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM7SMEN)
+
+#define __HAL_RCC_WWDG_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_WWDGSMEN)
+
+#define __HAL_RCC_SPI2_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_SPI2SMEN)
+
+#define __HAL_RCC_SPI3_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_SPI3SMEN)
+
+#define __HAL_RCC_USART2_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USART2SMEN)
+
+#define __HAL_RCC_USART3_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USART3SMEN)
+
+#define __HAL_RCC_UART4_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_UART4SMEN)
+
+#define __HAL_RCC_UART5_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_UART5SMEN)
+
+#define __HAL_RCC_I2C1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C1SMEN)
+
+#define __HAL_RCC_I2C2_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C2SMEN)
+
+#define __HAL_RCC_I2C3_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C3SMEN)
+
+#define __HAL_RCC_CAN1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_CAN1SMEN)
+
+#define __HAL_RCC_PWR_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_PWRSMEN)
+
+#define __HAL_RCC_DAC1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_DAC1SMEN)
+
+#define __HAL_RCC_OPAMP_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_OPAMPSMEN)
+
+#define __HAL_RCC_LPTIM1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LPTIM1SMEN)
+
+#define __HAL_RCC_LPUART1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPUART1SMEN)
+
+#define __HAL_RCC_SWPMI1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_SWPMI1SMEN)
+
+#define __HAL_RCC_LPTIM2_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPTIM2SMEN)
+
+#define __HAL_RCC_TIM2_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM2SMEN)
+
+#define __HAL_RCC_TIM3_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM3SMEN)
+
+#define __HAL_RCC_TIM4_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM4SMEN)
+
+#define __HAL_RCC_TIM5_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM5SMEN)
+
+#define __HAL_RCC_TIM6_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM6SMEN)
+
+#define __HAL_RCC_TIM7_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM7SMEN)
+
+#define __HAL_RCC_WWDG_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_WWDGSMEN)
+
+#define __HAL_RCC_SPI2_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_SPI2SMEN)
+
+#define __HAL_RCC_SPI3_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_SPI3SMEN)
+
+#define __HAL_RCC_USART2_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USART2SMEN)
+
+#define __HAL_RCC_USART3_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USART3SMEN)
+
+#define __HAL_RCC_UART4_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_UART4SMEN)
+
+#define __HAL_RCC_UART5_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_UART5SMEN)
+
+#define __HAL_RCC_I2C1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C1SMEN)
+
+#define __HAL_RCC_I2C2_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C2SMEN)
+
+#define __HAL_RCC_I2C3_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C3SMEN)
+
+#define __HAL_RCC_CAN1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_CAN1SMEN)
+
+#define __HAL_RCC_PWR_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_PWRSMEN)
+
+#define __HAL_RCC_DAC1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_DAC1SMEN)
+
+#define __HAL_RCC_OPAMP_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_OPAMPSMEN)
+
+#define __HAL_RCC_LPTIM1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LPTIM1SMEN)
+
+#define __HAL_RCC_LPUART1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPUART1SMEN)
+
+#define __HAL_RCC_SWPMI1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_SWPMI1SMEN)
+
+#define __HAL_RCC_LPTIM2_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPTIM2SMEN)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_APB2_Clock_Sleep_Enable_Disable APB2 Peripheral Clock Sleep Enable Disable
+ * @brief Enable or disable the APB2 peripheral clock during Low Power (Sleep) mode.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+
+#define __HAL_RCC_SYSCFG_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SYSCFGSMEN)
+
+#define __HAL_RCC_SDMMC1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SDMMC1SMEN)
+
+#define __HAL_RCC_TIM1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM1SMEN)
+
+#define __HAL_RCC_SPI1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SPI1SMEN)
+
+#define __HAL_RCC_TIM8_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM8SMEN)
+
+#define __HAL_RCC_USART1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_USART1SMEN)
+
+#define __HAL_RCC_TIM15_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM15SMEN)
+
+#define __HAL_RCC_TIM16_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM16SMEN)
+
+#define __HAL_RCC_TIM17_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM17SMEN)
+
+#define __HAL_RCC_SAI1_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SAI1SMEN)
+
+#define __HAL_RCC_SAI2_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SAI2SMEN)
+
+#define __HAL_RCC_DFSDM_CLK_SLEEP_ENABLE() SET_BIT(RCC->APB2SMENR, RCC_APB2SMENR_DFSDMSMEN)
+
+#define __HAL_RCC_SYSCFG_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SYSCFGSMEN)
+
+#define __HAL_RCC_SDMMC1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SDMMC1SMEN)
+
+#define __HAL_RCC_TIM1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM1SMEN)
+
+#define __HAL_RCC_SPI1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SPI1SMEN)
+
+#define __HAL_RCC_TIM8_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM8SMEN)
+
+#define __HAL_RCC_USART1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_USART1SMEN)
+
+#define __HAL_RCC_TIM15_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM15SMEN)
+
+#define __HAL_RCC_TIM16_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM16SMEN)
+
+#define __HAL_RCC_TIM17_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM17SMEN)
+
+#define __HAL_RCC_SAI1_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SAI1SMEN)
+
+#define __HAL_RCC_SAI2_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SAI2SMEN)
+
+#define __HAL_RCC_DFSDM_CLK_SLEEP_DISABLE() CLEAR_BIT(RCC->APB2SMENR, RCC_APB2SMENR_DFSDMSMEN)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_AHB1_Clock_Sleep_Enable_Disable_Status AHB1 Peripheral Clock Sleep Enabled or Disabled Status
+ * @brief Check whether the AHB1 peripheral clock during Low Power (Sleep) mode is enabled or not.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+
+#define __HAL_RCC_DMA1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA1SMEN) != RESET)
+
+#define __HAL_RCC_DMA2_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA2SMEN) != RESET)
+
+#define __HAL_RCC_FLASH_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_FLASHSMEN) != RESET)
+
+#define __HAL_RCC_SRAM1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_SRAM1SMEN) != RESET)
+
+#define __HAL_RCC_CRC_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_CRCSMEN) != RESET)
+
+#define __HAL_RCC_TSC_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_TSCSMEN) != RESET)
+
+#define __HAL_RCC_DMA1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA1SMEN) == RESET)
+
+#define __HAL_RCC_DMA2_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_DMA2SMEN) == RESET)
+
+#define __HAL_RCC_FLASH_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_FLASHSMEN) == RESET)
+
+#define __HAL_RCC_SRAM1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_SRAM1SMEN) == RESET)
+
+#define __HAL_RCC_CRC_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_CRCSMEN) == RESET)
+
+#define __HAL_RCC_TSC_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB1SMENR, RCC_AHB1SMENR_TSCSMEN) == RESET)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_AHB2_Clock_Sleep_Enable_Disable_Status AHB2 Peripheral Clock Sleep Enabled or Disabled Status
+ * @brief Check whether the AHB2 peripheral clock during Low Power (Sleep) mode is enabled or not.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+
+#define __HAL_RCC_GPIOA_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOASMEN) != RESET)
+
+#define __HAL_RCC_GPIOB_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOBSMEN) != RESET)
+
+#define __HAL_RCC_GPIOC_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOCSMEN) != RESET)
+
+#define __HAL_RCC_GPIOD_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIODSMEN) != RESET)
+
+#define __HAL_RCC_GPIOE_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOESMEN) != RESET)
+
+#define __HAL_RCC_GPIOF_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOFSMEN) != RESET)
+
+#define __HAL_RCC_GPIOG_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOGSMEN) != RESET)
+
+#define __HAL_RCC_GPIOH_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOHSMEN) != RESET)
+
+#define __HAL_RCC_SRAM2_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_SRAM2SMEN) != RESET)
+
+#define __HAL_RCC_ADC_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_ADCSMEN) != RESET)
+
+#define __HAL_RCC_RNG_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_RNGSMEN) != RESET)
+
+#define __HAL_RCC_GPIOA_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOASMEN) == RESET)
+
+#define __HAL_RCC_GPIOB_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOBSMEN) == RESET)
+
+#define __HAL_RCC_GPIOC_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOCSMEN) == RESET)
+
+#define __HAL_RCC_GPIOD_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIODSMEN) == RESET)
+
+#define __HAL_RCC_GPIOE_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOESMEN) == RESET)
+
+#define __HAL_RCC_GPIOF_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOFSMEN) == RESET)
+
+#define __HAL_RCC_GPIOG_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOGSMEN) == RESET)
+
+#define __HAL_RCC_GPIOH_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_GPIOHSMEN) == RESET)
+
+#define __HAL_RCC_ADC_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_ADCSMEN) == RESET)
+
+#define __HAL_RCC_SRAM2_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_SRAM2SMEN) == RESET)
+
+#define __HAL_RCC_RNG_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB2SMENR, RCC_AHB2SMENR_RNGSMEN) == RESET)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_AHB3_Clock_Sleep_Enable_Disable_Status AHB3 Peripheral Clock Sleep Enabled or Disabled Status
+ * @brief Check whether the AHB3 peripheral clock during Low Power (Sleep) mode is enabled or not.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+
+#define __HAL_RCC_QSPI_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_QSPISMEN) != RESET)
+
+#define __HAL_RCC_FMC_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_FMCSMEN) != RESET)
+
+#define __HAL_RCC_QSPI_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_QSPISMEN) == RESET)
+
+#define __HAL_RCC_FMC_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->AHB3SMENR, RCC_AHB3SMENR_FMCSMEN) == RESET)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_APB1_Clock_Sleep_Enable_Disable_Status APB1 Peripheral Clock Sleep Enabled or Disabled Status
+ * @brief Check whether the APB1 peripheral clock during Low Power (Sleep) mode is enabled or not.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+
+#define __HAL_RCC_TIM2_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM2SMEN) != RESET)
+
+#define __HAL_RCC_TIM3_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM3SMEN) != RESET)
+
+#define __HAL_RCC_TIM4_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM4SMEN) != RESET)
+
+#define __HAL_RCC_TIM5_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM5SMEN) != RESET)
+
+#define __HAL_RCC_TIM6_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM6SMEN) != RESET)
+
+#define __HAL_RCC_TIM7_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM7SMEN) != RESET)
+
+#define __HAL_RCC_WWDG_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_WWDGSMEN) != RESET)
+
+#define __HAL_RCC_SPI2_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_SPI2SMEN) != RESET)
+
+#define __HAL_RCC_SPI3_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_SPI3SMEN) != RESET)
+
+#define __HAL_RCC_USART2_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USART2SMEN) != RESET)
+
+#define __HAL_RCC_USART3_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USART3SMEN) != RESET)
+
+#define __HAL_RCC_UART4_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_UART4SMEN) != RESET)
+
+#define __HAL_RCC_UART5_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_UART5SMEN) != RESET)
+
+#define __HAL_RCC_I2C1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C1SMEN) != RESET)
+
+#define __HAL_RCC_I2C2_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C2SMEN) != RESET)
+
+#define __HAL_RCC_I2C3_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C3SMEN) != RESET)
+
+#define __HAL_RCC_CAN1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_CAN1SMEN) != RESET)
+
+#define __HAL_RCC_PWR_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_PWRSMEN) != RESET)
+
+#define __HAL_RCC_DAC1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_DAC1SMEN) != RESET)
+
+#define __HAL_RCC_OPAMP_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_OPAMPSMEN) != RESET)
+
+#define __HAL_RCC_LPTIM1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LPTIM1SMEN) != RESET)
+
+#define __HAL_RCC_LPUART1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPUART1SMEN) != RESET)
+
+#define __HAL_RCC_SWPMI1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_SWPMI1SMEN) != RESET)
+
+#define __HAL_RCC_LPTIM2_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPTIM2SMEN) != RESET)
+
+#define __HAL_RCC_TIM2_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM2SMEN) == RESET)
+
+#define __HAL_RCC_TIM3_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM3SMEN) == RESET)
+
+#define __HAL_RCC_TIM4_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM4SMEN) == RESET)
+
+#define __HAL_RCC_TIM5_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM5SMEN) == RESET)
+
+#define __HAL_RCC_TIM6_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM6SMEN) == RESET)
+
+#define __HAL_RCC_TIM7_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_TIM7SMEN) == RESET)
+
+#define __HAL_RCC_WWDG_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_WWDGSMEN) == RESET)
+
+#define __HAL_RCC_SPI2_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_SPI2SMEN) == RESET)
+
+#define __HAL_RCC_SPI3_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_SPI3SMEN) == RESET)
+
+#define __HAL_RCC_USART2_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USART2SMEN) == RESET)
+
+#define __HAL_RCC_USART3_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_USART3SMEN) == RESET)
+
+#define __HAL_RCC_UART4_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_UART4SMEN) == RESET)
+
+#define __HAL_RCC_UART5_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_UART5SMEN) == RESET)
+
+#define __HAL_RCC_I2C1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C1SMEN) == RESET)
+
+#define __HAL_RCC_I2C2_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C2SMEN) == RESET)
+
+#define __HAL_RCC_I2C3_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_I2C3SMEN) == RESET)
+
+#define __HAL_RCC_CAN1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_CAN1SMEN) == RESET)
+
+#define __HAL_RCC_PWR_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_PWRSMEN) == RESET)
+
+#define __HAL_RCC_DAC1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_DAC1SMEN) == RESET)
+
+#define __HAL_RCC_OPAMP_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_OPAMPSMEN) == RESET)
+
+#define __HAL_RCC_LPTIM1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR1, RCC_APB1SMENR1_LPTIM1SMEN) == RESET)
+
+#define __HAL_RCC_LPUART1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPUART1SMEN) == RESET)
+
+#define __HAL_RCC_SWPMI1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_SWPMI1SMEN) == RESET)
+
+#define __HAL_RCC_LPTIM2_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB1SMENR2, RCC_APB1SMENR2_LPTIM2SMEN) == RESET)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_APB2_Clock_Sleep_Enable_Disable_Status APB2 Peripheral Clock Sleep Enabled or Disabled Status
+ * @brief Check whether the APB2 peripheral clock during Low Power (Sleep) mode is enabled or not.
+ * @note Peripheral clock gating in SLEEP mode can be used to further reduce
+ * power consumption.
+ * @note After wakeup from SLEEP mode, the peripheral clock is enabled again.
+ * @note By default, all peripheral clocks are enabled during SLEEP mode.
+ * @{
+ */
+
+#define __HAL_RCC_SYSCFG_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SYSCFGSMEN) != RESET)
+
+#define __HAL_RCC_SDMMC1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SDMMC1SMEN) != RESET)
+
+#define __HAL_RCC_TIM1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM1SMEN) != RESET)
+
+#define __HAL_RCC_SPI1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SPI1SMEN) != RESET)
+
+#define __HAL_RCC_TIM8_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM8SMEN) != RESET)
+
+#define __HAL_RCC_USART1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_USART1SMEN) != RESET)
+
+#define __HAL_RCC_TIM15_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM15SMEN) != RESET)
+
+#define __HAL_RCC_TIM16_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM16SMEN) != RESET)
+
+#define __HAL_RCC_TIM17_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM17SMEN) != RESET)
+
+#define __HAL_RCC_SAI1_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SAI1SMEN) != RESET)
+
+#define __HAL_RCC_SAI2_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SAI2SMEN) != RESET)
+
+#define __HAL_RCC_DFSDM_IS_CLK_SLEEP_ENABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_DFSDMSMEN) != RESET)
+
+#define __HAL_RCC_SYSCFG_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SYSCFGSMEN) == RESET)
+
+#define __HAL_RCC_SDMMC1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SDMMC1SMEN) == RESET)
+
+#define __HAL_RCC_TIM1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM1SMEN) == RESET)
+
+#define __HAL_RCC_SPI1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SPI1SMEN) == RESET)
+
+#define __HAL_RCC_TIM8_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM8SMEN) == RESET)
+
+#define __HAL_RCC_USART1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_USART1SMEN) == RESET)
+
+#define __HAL_RCC_TIM15_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM15SMEN) == RESET)
+
+#define __HAL_RCC_TIM16_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM16SMEN) == RESET)
+
+#define __HAL_RCC_TIM17_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_TIM17SMEN) == RESET)
+
+#define __HAL_RCC_SAI1_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SAI1SMEN) == RESET)
+
+#define __HAL_RCC_SAI2_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_SAI2SMEN) == RESET)
+
+#define __HAL_RCC_DFSDM_IS_CLK_SLEEP_DISABLED() (READ_BIT(RCC->APB2SMENR, RCC_APB2SMENR_DFSDMSMEN) == RESET)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_Backup_Domain_Reset RCC Backup Domain Reset
+ * @{
+ */
+
+/** @brief Macros to force or release the Backup domain reset.
+ * @note This function resets the RTC peripheral (including the backup registers)
+ * and the RTC clock source selection in RCC_CSR register.
+ * @note The BKPSRAM is not affected by this reset.
+ * @retval None
+ */
+#define __HAL_RCC_BACKUPRESET_FORCE() SET_BIT(RCC->BDCR, RCC_BDCR_BDRST)
+
+#define __HAL_RCC_BACKUPRESET_RELEASE() CLEAR_BIT(RCC->BDCR, RCC_BDCR_BDRST)
+
+/**
+ * @}
+ */
+
+/** @defgroup RCC_RTC_Clock_Configuration RCC RTC Clock Configuration
+ * @{
+ */
+
+/** @brief Macros to enable or disable the RTC clock.
+ * @note As the RTC is in the Backup domain and write access is denied to
+ * this domain after reset, you have to enable write access using
+ * HAL_PWR_EnableBkUpAccess() function before to configure the RTC
+ * (to be done once after reset).
+ * @note These macros must be used after the RTC clock source was selected.
+ * @retval None
+ */
+#define __HAL_RCC_RTC_ENABLE() SET_BIT(RCC->BDCR, RCC_BDCR_RTCEN)
+
+#define __HAL_RCC_RTC_DISABLE() CLEAR_BIT(RCC->BDCR, RCC_BDCR_RTCEN)
+
+/**
+ * @}
+ */
+
+/** @brief Macros to enable or disable the Internal High Speed oscillator (HSI).
+ * @note The HSI is stopped by hardware when entering STOP and STANDBY modes.
+ * It is used (enabled by hardware) as system clock source after startup
+ * from Reset, wakeup from STOP and STANDBY mode, or in case of failure
+ * of the HSE used directly or indirectly as system clock (if the Clock
+ * Security System CSS is enabled).
+ * @note HSI can not be stopped if it is used as system clock source. In this case,
+ * you have to select another source of the system clock then stop the HSI.
+ * @note After enabling the HSI, the application software should wait on HSIRDY
+ * flag to be set indicating that HSI clock is stable and can be used as
+ * system clock source.
+ * This parameter can be: ENABLE or DISABLE.
+ * @note When the HSI is stopped, HSIRDY flag goes low after 6 HSI oscillator
+ * clock cycles.
+ * @retval None
+ */
+#define __HAL_RCC_HSI_ENABLE() SET_BIT(RCC->CR, RCC_CR_HSION)
+
+#define __HAL_RCC_HSI_DISABLE() CLEAR_BIT(RCC->CR, RCC_CR_HSION)
+
+/** @brief Macro to adjust the Internal High Speed oscillator (HSI) calibration value.
+ * @note The calibration is used to compensate for the variations in voltage
+ * and temperature that influence the frequency of the internal HSI RC.
+ * @param __HSICALIBRATIONVALUE__: specifies the calibration trimming value
+ * (default is RCC_HSICALIBRATION_DEFAULT).
+ * This parameter must be a number between 0 and 31.
+ * @retval None
+ */
+#define __HAL_RCC_HSI_CALIBRATIONVALUE_ADJUST(__HSICALIBRATIONVALUE__) \
+ MODIFY_REG(RCC->ICSCR, RCC_ICSCR_HSITRIM, (uint32_t)(__HSICALIBRATIONVALUE__) << POSITION_VAL(RCC_ICSCR_HSITRIM))
+
+/**
+ * @brief Macros to enable or disable the wakeup the Internal High Speed oscillator (HSI)
+ * in parallel to the Internal Multi Speed oscillator (MSI) used at system wakeup.
+ * @note The enable of this function has not effect on the HSION bit.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+#define __HAL_RCC_HSIAUTOMATIC_START_ENABLE() SET_BIT(RCC->CR, RCC_CR_HSIASFS)
+
+#define __HAL_RCC_HSIAUTOMATIC_START_DISABLE() CLEAR_BIT(RCC->CR, RCC_CR_HSIASFS)
+
+/**
+ * @brief Macros to enable or disable the force of the Internal High Speed oscillator (HSI)
+ * in STOP mode to be quickly available as kernel clock for USARTs and I2Cs.
+ * @note Keeping the HSI ON in STOP mode allows to avoid slowing down the communication
+ * speed because of the HSI startup time.
+ * @note The enable of this function has not effect on the HSION bit.
+ * This parameter can be: ENABLE or DISABLE.
+ * @retval None
+ */
+#define __HAL_RCC_HSISTOP_ENABLE() SET_BIT(RCC->CR, RCC_CR_HSIKERON)
+
+#define __HAL_RCC_HSISTOP_DISABLE() CLEAR_BIT(RCC->CR, RCC_CR_HSIKERON)
+
+/**
+ * @brief Macros to enable or disable the Internal Multi Speed oscillator (MSI).
+ * @note The MSI is stopped by hardware when entering STOP and STANDBY modes.
+ * It is used (enabled by hardware) as system clock source after
+ * startup from Reset, wakeup from STOP and STANDBY mode, or in case
+ * of failure of the HSE used directly or indirectly as system clock
+ * (if the Clock Security System CSS is enabled).
+ * @note MSI can not be stopped if it is used as system clock source.
+ * In this case, you have to select another source of the system
+ * clock then stop the MSI.
+ * @note After enabling the MSI, the application software should wait on
+ * MSIRDY flag to be set indicating that MSI clock is stable and can
+ * be used as system clock source.
+ * @note When the MSI is stopped, MSIRDY flag goes low after 6 MSI oscillator
+ * clock cycles.
+ * @retval None
+ */
+#define __HAL_RCC_MSI_ENABLE() SET_BIT(RCC->CR, RCC_CR_MSION)
+
+#define __HAL_RCC_MSI_DISABLE() CLEAR_BIT(RCC->CR, RCC_CR_MSION)
+
+/** @brief Macro Adjusts the Internal Multi Speed oscillator (MSI) calibration value.
+ * @note The calibration is used to compensate for the variations in voltage
+ * and temperature that influence the frequency of the internal MSI RC.
+ * Refer to the Application Note AN3300 for more details on how to
+ * calibrate the MSI.
+ * @param __MSICALIBRATIONVALUE__: specifies the calibration trimming value
+ * (default is RCC_MSICALIBRATION_DEFAULT).
+ * This parameter must be a number between 0 and 255.
+ * @retval None
+ */
+#define __HAL_RCC_MSI_CALIBRATIONVALUE_ADJUST(__MSICALIBRATIONVALUE__) \
+ MODIFY_REG(RCC->ICSCR, RCC_ICSCR_MSITRIM, (uint32_t)(__MSICALIBRATIONVALUE__) << 8)
+
+/**
+ * @brief Macro configures the Internal Multi Speed oscillator (MSI) clock range in run mode
+ * @note After restart from Reset , the MSI clock is around 4 MHz.
+ * After stop the startup clock can be MSI (at any of its possible
+ * frequencies, the one that was used before entering stop mode) or HSI.
+ * After Standby its frequency can be selected between 4 possible values
+ * (1, 2, 4 or 8 MHz).
+ * @note MSIRANGE can be modified when MSI is OFF (MSION=0) or when MSI is ready
+ * (MSIRDY=1).
+ * @note The MSI clock range after reset can be modified on the fly.
+ * @param __MSIRANGEVALUE__: specifies the MSI clock range.
+ * This parameter must be one of the following values:
+ * @arg RCC_MSIRANGE_0: MSI clock is around 100 KHz
+ * @arg RCC_MSIRANGE_1: MSI clock is around 200 KHz
+ * @arg RCC_MSIRANGE_2: MSI clock is around 400 KHz
+ * @arg RCC_MSIRANGE_3: MSI clock is around 800 KHz
+ * @arg RCC_MSIRANGE_4: MSI clock is around 1 MHz
+ * @arg RCC_MSIRANGE_5: MSI clock is around 2MHz
+ * @arg RCC_MSIRANGE_6: MSI clock is around 4MHz (default after Reset)
+ * @arg RCC_MSIRANGE_7: MSI clock is around 8 MHz
+ * @arg RCC_MSIRANGE_8: MSI clock is around 16 MHz
+ * @arg RCC_MSIRANGE_9: MSI clock is around 24 MHz
+ * @arg RCC_MSIRANGE_10: MSI clock is around 32 MHz
+ * @arg RCC_MSIRANGE_11: MSI clock is around 48 MHz
+ * @retval None
+ */
+#define __HAL_RCC_MSI_RANGE_CONFIG(__MSIRANGEVALUE__) \
+ do { \
+ SET_BIT(RCC->CR, RCC_CR_MSIRGSEL); \
+ MODIFY_REG(RCC->CR, RCC_CR_MSIRANGE, (__MSIRANGEVALUE__)); \
+ } while(0)
+
+/**
+ * @brief Macro configures the Internal Multi Speed oscillator (MSI) clock range after Standby mode
+ * After Standby its frequency can be selected between 4 possible values (1, 2, 4 or 8 MHz).
+ * @param __MSIRANGEVALUE__: specifies the MSI clock range.
+ * This parameter must be one of the following values:
+ * @arg RCC_MSIRANGE_4: MSI clock is around 1 MHz
+ * @arg RCC_MSIRANGE_5: MSI clock is around 2MHz
+ * @arg RCC_MSIRANGE_6: MSI clock is around 4MHz (default after Reset)
+ * @arg RCC_MSIRANGE_7: MSI clock is around 8 MHz
+ * @retval None
+ */
+#define __HAL_RCC_MSI_STANDBY_RANGE_CONFIG(__MSIRANGEVALUE__) \
+ MODIFY_REG(RCC->CSR, RCC_CSR_MSISRANGE, (__MSIRANGEVALUE__) << 4U)
+
+/** @brief Macro to get the Internal Multi Speed oscillator (MSI) clock range in run mode
+ * @retval MSI clock range.
+ * This parameter must be one of the following values:
+ * @arg RCC_MSIRANGE_0: MSI clock is around 100 KHz
+ * @arg RCC_MSIRANGE_1: MSI clock is around 200 KHz
+ * @arg RCC_MSIRANGE_2: MSI clock is around 400 KHz
+ * @arg RCC_MSIRANGE_3: MSI clock is around 800 KHz
+ * @arg RCC_MSIRANGE_4: MSI clock is around 1 MHz
+ * @arg RCC_MSIRANGE_5: MSI clock is around 2MHz
+ * @arg RCC_MSIRANGE_6: MSI clock is around 4MHz (default after Reset)
+ * @arg RCC_MSIRANGE_7: MSI clock is around 8 MHz
+ * @arg RCC_MSIRANGE_8: MSI clock is around 16 MHz
+ * @arg RCC_MSIRANGE_9: MSI clock is around 24 MHz
+ * @arg RCC_MSIRANGE_10: MSI clock is around 32 MHz
+ * @arg RCC_MSIRANGE_11: MSI clock is around 48 MHz
+ */
+#define __HAL_RCC_GET_MSI_RANGE() \
+ ((READ_BIT(RCC->CR, RCC_CR_MSIRGSEL) != RESET) ? \
+ (uint32_t)(READ_BIT(RCC->CR, RCC_CR_MSIRANGE)) : \
+ (uint32_t)(READ_BIT(RCC->CSR, RCC_CSR_MSISRANGE) >> 4))
+
+/** @brief Macros to enable or disable the Internal Low Speed oscillator (LSI).
+ * @note After enabling the LSI, the application software should wait on
+ * LSIRDY flag to be set indicating that LSI clock is stable and can
+ * be used to clock the IWDG and/or the RTC.
+ * @note LSI can not be disabled if the IWDG is running.
+ * @note When the LSI is stopped, LSIRDY flag goes low after 6 LSI oscillator
+ * clock cycles.
+ * @retval None
+ */
+#define __HAL_RCC_LSI_ENABLE() SET_BIT(RCC->CSR, RCC_CSR_LSION)
+
+#define __HAL_RCC_LSI_DISABLE() CLEAR_BIT(RCC->CSR, RCC_CSR_LSION)
+
+/**
+ * @brief Macro to configure the External High Speed oscillator (HSE).
+ * @note Transition HSE Bypass to HSE On and HSE On to HSE Bypass are not
+ * supported by this macro. User should request a transition to HSE Off
+ * first and then HSE On or HSE Bypass.
+ * @note After enabling the HSE (RCC_HSE_ON or RCC_HSE_Bypass), the application
+ * software should wait on HSERDY flag to be set indicating that HSE clock
+ * is stable and can be used to clock the PLL and/or system clock.
+ * @note HSE state can not be changed if it is used directly or through the
+ * PLL as system clock. In this case, you have to select another source
+ * of the system clock then change the HSE state (ex. disable it).
+ * @note The HSE is stopped by hardware when entering STOP and STANDBY modes.
+ * @note This function reset the CSSON bit, so if the clock security system(CSS)
+ * was previously enabled you have to enable it again after calling this
+ * function.
+ * @param __STATE__: specifies the new state of the HSE.
+ * This parameter can be one of the following values:
+ * @arg RCC_HSE_OFF: turn OFF the HSE oscillator, HSERDY flag goes low after
+ * 6 HSE oscillator clock cycles.
+ * @arg RCC_HSE_ON: turn ON the HSE oscillator.
+ * @arg RCC_HSE_BYPASS: HSE oscillator bypassed with external clock.
+ * @retval None
+ */
+#define __HAL_RCC_HSE_CONFIG(__STATE__) \
+ do { \
+ if((__STATE__) == RCC_HSE_ON) \
+ { \
+ SET_BIT(RCC->CR, RCC_CR_HSEON); \
+ } \
+ else if((__STATE__) == RCC_HSE_BYPASS) \
+ { \
+ CLEAR_BIT(RCC->CR, RCC_CR_HSEON); \
+ SET_BIT(RCC->CR, RCC_CR_HSEBYP); \
+ SET_BIT(RCC->CR, RCC_CR_HSEON); \
+ } \
+ else \
+ { \
+ CLEAR_BIT(RCC->CR, RCC_CR_HSEON); \
+ CLEAR_BIT(RCC->CR, RCC_CR_HSEBYP); \
+ } \
+ } while(0)
+
+/**
+ * @brief Macro to configure the External Low Speed oscillator (LSE).
+ * @note Transitions LSE Bypass to LSE On and LSE On to LSE Bypass are not
+ * supported by this macro. User should request a transition to LSE Off
+ * first and then LSE On or LSE Bypass.
+ * @note As the LSE is in the Backup domain and write access is denied to
+ * this domain after reset, you have to enable write access using
+ * HAL_PWR_EnableBkUpAccess() function before to configure the LSE
+ * (to be done once after reset).
+ * @note After enabling the LSE (RCC_LSE_ON or RCC_LSE_BYPASS), the application
+ * software should wait on LSERDY flag to be set indicating that LSE clock
+ * is stable and can be used to clock the RTC.
+ * @param __STATE__: specifies the new state of the LSE.
+ * This parameter can be one of the following values:
+ * @arg RCC_LSE_OFF: turn OFF the LSE oscillator, LSERDY flag goes low after
+ * 6 LSE oscillator clock cycles.
+ * @arg RCC_LSE_ON: turn ON the LSE oscillator.
+ * @arg RCC_LSE_BYPASS: LSE oscillator bypassed with external clock.
+ * @retval None
+ */
+#define __HAL_RCC_LSE_CONFIG(__STATE__) \
+ do { \
+ if((__STATE__) == RCC_LSE_ON) \
+ { \
+ SET_BIT(RCC->BDCR, RCC_BDCR_LSEON); \
+ } \
+ else if((__STATE__) == RCC_LSE_OFF) \
+ { \
+ CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEON); \
+ CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEBYP); \
+ } \
+ else if((__STATE__) == RCC_LSE_BYPASS) \
+ { \
+ CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEON); \
+ SET_BIT(RCC->BDCR, RCC_BDCR_LSEBYP); \
+ SET_BIT(RCC->BDCR, RCC_BDCR_LSEON); \
+ } \
+ else \
+ { \
+ CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEON); \
+ CLEAR_BIT(RCC->BDCR, RCC_BDCR_LSEBYP); \
+ } \
+ } while(0)
+
+/** @brief Macros to configure the RTC clock (RTCCLK).
+ * @note As the RTC clock configuration bits are in the Backup domain and write
+ * access is denied to this domain after reset, you have to enable write
+ * access using the Power Backup Access macro before to configure
+ * the RTC clock source (to be done once after reset).
+ * @note Once the RTC clock is configured it cannot be changed unless the
+ * Backup domain is reset using __HAL_RCC_BACKUPRESET_FORCE() macro, or by
+ * a Power On Reset (POR).
+ *
+ * @param __RTC_CLKSOURCE__: specifies the RTC clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_RTCCLKSOURCE_LSE: LSE selected as RTC clock.
+ * @arg RCC_RTCCLKSOURCE_LSI: LSI selected as RTC clock.
+ * @arg RCC_RTCCLKSOURCE_HSE_DIV32: HSE clock divided by 32 selected
+ *
+ * @note If the LSE or LSI is used as RTC clock source, the RTC continues to
+ * work in STOP and STANDBY modes, and can be used as wakeup source.
+ * However, when the HSE clock is used as RTC clock source, the RTC
+ * cannot be used in STOP and STANDBY modes.
+ * @note The maximum input clock frequency for RTC is 1MHz (when using HSE as
+ * RTC clock source).
+ * @retval None
+ */
+#define __HAL_RCC_RTC_CONFIG(__RTC_CLKSOURCE__) \
+ MODIFY_REG( RCC->BDCR, RCC_BDCR_RTCSEL, (__RTC_CLKSOURCE__))
+
+
+/** @brief Macro to get the RTC clock source.
+ * @retval The returned value can be one of the following:
+ * @arg RCC_RTCCLKSOURCE_LSE: LSE selected as RTC clock.
+ * @arg RCC_RTCCLKSOURCE_LSI: LSI selected as RTC clock.
+ * @arg RCC_RTCCLKSOURCE_HSE_DIV32: HSE clock divided by 32 selected
+ */
+#define __HAL_RCC_GET_RTC_SOURCE() ((uint32_t)(READ_BIT(RCC->BDCR, RCC_BDCR_RTCSEL)))
+
+/** @brief Macros to enable or disable the main PLL.
+ * @note After enabling the main PLL, the application software should wait on
+ * PLLRDY flag to be set indicating that PLL clock is stable and can
+ * be used as system clock source.
+ * @note The main PLL can not be disabled if it is used as system clock source
+ * @note The main PLL is disabled by hardware when entering STOP and STANDBY modes.
+ * @retval None
+ */
+#define __HAL_RCC_PLL_ENABLE() SET_BIT(RCC->CR, RCC_CR_PLLON)
+
+#define __HAL_RCC_PLL_DISABLE() CLEAR_BIT(RCC->CR, RCC_CR_PLLON)
+
+/** @brief Macro to configure the PLL clock source.
+ * @note This function must be used only when the main PLL is disabled.
+ * @param __PLLSOURCE__: specifies the PLL entry clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_PLLSOURCE_NONE: No clock selected as PLL clock entry
+ * @arg RCC_PLLSOURCE_MSI: MSI oscillator clock selected as PLL clock entry
+ * @arg RCC_PLLSOURCE_HSI: HSI oscillator clock selected as PLL clock entry
+ * @arg RCC_PLLSOURCE_HSE: HSE oscillator clock selected as PLL clock entry
+ * @note This clock source is common for the main PLL and audio PLL (PLLSAI1 and PLLSAI2).
+ * @retval None
+ *
+ */
+#define __HAL_RCC_PLL_PLLSOURCE_CONFIG(__PLLSOURCE__) \
+ MODIFY_REG(RCC->PLLCFGR, RCC_PLLCFGR_PLLSRC, (__PLLSOURCE__))
+
+/** @brief Macro to configure the PLL multiplication factor.
+ * @note This function must be used only when the main PLL is disabled.
+ * @param __PLLM__: specifies the division factor for PLL VCO input clock
+ * This parameter must be a number between Min_Data = 1 and Max_Data = 8.
+ * @note You have to set the PLLM parameter correctly to ensure that the VCO input
+ * frequency ranges from 4 to 16 MHz. It is recommended to select a frequency
+ * of 16 MHz to limit PLL jitter.
+ * @retval None
+ *
+ */
+#define __HAL_RCC_PLL_PLLM_CONFIG(__PLLM__) \
+ MODIFY_REG(RCC->PLLCFGR, RCC_PLLCFGR_PLLM, ((__PLLM__) - 1) << 4U)
+
+/**
+ * @brief Macro to configure the main PLL clock source, multiplication and division factors.
+ * @note This function must be used only when the main PLL is disabled.
+ *
+ * @param __PLLSOURCE__: specifies the PLL entry clock source.
+ * This parameter can be one of the following values:
+ * @arg RCC_PLLSOURCE_NONE: No clock selected as PLL clock entry
+ * @arg RCC_PLLSOURCE_MSI: MSI oscillator clock selected as PLL clock entry
+ * @arg RCC_PLLSOURCE_HSI: HSI oscillator clock selected as PLL clock entry
+ * @arg RCC_PLLSOURCE_HSE: HSE oscillator clock selected as PLL clock entry
+ * @note This clock source is common for the main PLL and audio PLL (PLLSAI1 and PLLSAI2).
+ *
+ * @param __PLLM__: specifies the division factor for PLL VCO input clock.
+ * This parameter must be a number between 1 and 8.
+ * @note You have to set the PLLM parameter correctly to ensure that the VCO input
+ * frequency ranges from 4 to 16 MHz. It is recommended to select a frequency
+ * of 16 MHz to limit PLL jitter.
+ *
+ * @param __PLLN__: specifies the multiplication factor for PLL VCO output clock.
+ * This parameter must be a number between 8 and 86.
+ * @note You have to set the PLLN parameter correctly to ensure that the VCO
+ * output frequency is between 64 and 344 MHz.
+ *
+ * @param __PLLP__: specifies the division factor for SAI clock.
+ * This parameter must be a number in the range (7 or 17).
+ *
+ * @param __PLLQ__: specifies the division factor for OTG FS, SDMMC1 and RNG clocks.
+ * This parameter must be in the range (2, 4, 6 or 8).
+ * @note If the USB OTG FS is used in your application, you have to set the
+ * PLLQ parameter correctly to have 48 MHz clock for the USB. However,
+ * the SDMMC1 and RNG need a frequency lower than or equal to 48 MHz to work
+ * correctly.
+ * @param __PLLR__: specifies the division factor for the main system clock.
+ * @note You have to set the PLLR parameter correctly to not exceed 80MHZ.
+ * This parameter must be in the range (2, 4, 6 or 8).
+ * @retval None
+ */
+#define __HAL_RCC_PLL_CONFIG(__PLLSOURCE__, __PLLM__, __PLLN__, __PLLP__, __PLLQ__,__PLLR__ ) \
+ (RCC->PLLCFGR = (((__PLLM__) - 1) << 4U) | ((__PLLN__) << 8U) | (((__PLLP__) >> 4U ) << 17U) | \
+ (__PLLSOURCE__) | ((((__PLLQ__) >> 1U) - 1) << 21U) | ((((__PLLR__) >> 1U) - 1) << 25U))
+
+/** @brief Macro to get the oscillator used as PLL clock source.
+ * @retval The oscillator used as PLL clock source. The returned value can be one
+ * of the following:
+ * - RCC_PLLSOURCE_NONE: No oscillator is used as PLL clock source.
+ * - RCC_PLLSOURCE_MSI: MSI oscillator is used as PLL clock source.
+ * - RCC_PLLSOURCE_HSI: HSI oscillator is used as PLL clock source.
+ * - RCC_PLLSOURCE_HSE: HSE oscillator is used as PLL clock source.
+ */
+#define __HAL_RCC_GET_PLL_OSCSOURCE() ((uint32_t)(RCC->PLLCFGR & RCC_PLLCFGR_PLLSRC))
+
+/**
+ * @brief Enable or disable each clock output (RCC_PLL_SYSCLK, RCC_PLL_48M1CLK, RCC_PLL_SAI3CLK)
+ * @note Enabling/disabling clock outputs RCC_PLL_SAI3CLK and RCC_PLL_48M1CLK can be done at anytime
+ * without the need to stop the PLL in order to save power. But RCC_PLL_SYSCLK cannot
+ * be stopped if used as System Clock.
+ * @param __PLLCLOCKOUT__: specifies the PLL clock to be output.
+ * This parameter can be one or a combination of the following values:
+ * @arg RCC_PLL_SAI3CLK: This clock is used to generate an accurate clock to achieve
+ * high-quality audio performance on SAI interface in case.
+ * @arg RCC_PLL_48M1CLK: This Clock is used to generate the clock for the USB OTG FS (48 MHz),
+ * the random analog generator (<=48 MHz) and the SDMMC1 (<= 48 MHz).
+ * @arg RCC_PLL_SYSCLK: This Clock is used to generate the high speed system clock (up to 80MHz)
+ * @retval None
+ */
+#define __HAL_RCC_PLLCLKOUT_ENABLE(__PLLCLOCKOUT__) SET_BIT(RCC->PLLCFGR, (__PLLCLOCKOUT__))
+
+#define __HAL_RCC_PLLCLKOUT_DISABLE(__PLLCLOCKOUT__) CLEAR_BIT(RCC->PLLCFGR, (__PLLCLOCKOUT__))
+
+/**
+ * @brief Get clock output enable status (RCC_PLL_SYSCLK, RCC_PLL_48M1CLK, RCC_PLL_SAI3CLK)
+ * @param __PLLCLOCKOUT__: specifies the output PLL clock to be checked.
+ * This parameter can be one of the following values:
+ * @arg RCC_PLL_SAI3CLK: This clock is used to generate an accurate clock to achieve
+ * high-quality audio performance on SAI interface in case.
+ * @arg RCC_PLL_48M1CLK: This Clock is used to generate the clock for the USB OTG FS (48 MHz),
+ * the random analog generator (<=48 MHz) and the SDMMC1 (<= 48 MHz).
+ * @arg RCC_PLL_SYSCLK: This Clock is used to generate the high speed system clock (up to 80MHz)
+ * @retval SET / RESET
+ */
+#define __HAL_RCC_GET_PLLCLKOUT_CONFIG(__PLLCLOCKOUT__) READ_BIT(RCC->PLLCFGR, (__PLLCLOCKOUT__))
+
+/**
+ * @brief Macro to configure the system clock source.
+ * @param __SYSCLKSOURCE__: specifies the system clock source.
+ * This parameter can be one of the following values:
+ * - RCC_SYSCLKSOURCE_MSI: MSI oscillator is used as system clock source.
+ * - RCC_SYSCLKSOURCE_HSI: HSI oscillator is used as system clock source.
+ * - RCC_SYSCLKSOURCE_HSE: HSE oscillator is used as system clock source.
+ * - RCC_SYSCLKSOURCE_PLLCLK: PLL output is used as system clock source.
+ * @retval None
+ */
+#define __HAL_RCC_SYSCLK_CONFIG(__SYSCLKSOURCE__) \
+ MODIFY_REG(RCC->CFGR, RCC_CFGR_SW, (__SYSCLKSOURCE__))
+
+/** @brief Macro to get the clock source used as system clock.
+ * @retval The clock source used as system clock. The returned value can be one
+ * of the following:
+ * - RCC_SYSCLKSOURCE_STATUS_MSI: MSI used as system clock.
+ * - RCC_SYSCLKSOURCE_STATUS_HSI: HSI used as system clock.
+ * - RCC_SYSCLKSOURCE_STATUS_HSE: HSE used as system clock.
+ * - RCC_SYSCLKSOURCE_STATUS_PLLCLK: PLL used as system clock.
+ */
+#define __HAL_RCC_GET_SYSCLK_SOURCE() ((uint32_t)(RCC->CFGR & RCC_CFGR_SWS))
+
+/**
+ * @brief Macro to configures the External Low Speed oscillator (LSE) drive capability.
+ * @note As the LSE is in the Backup domain and write access is denied to
+ * this domain after reset, you have to enable write access using
+ * HAL_PWR_EnableBkUpAccess() function before to configure the LSE
+ * (to be done once after reset).
+ * @param __LSEDRIVE__: specifies the new state of the LSE drive capability.
+ * This parameter can be one of the following values:
+ * @arg RCC_LSEDRIVE_LOW: LSE oscillator low drive capability.
+ * @arg RCC_LSEDRIVE_MEDIUMLOW: LSE oscillator medium low drive capability.
+ * @arg RCC_LSEDRIVE_MEDIUMHIGH: LSE oscillator medium high drive capability.
+ * @arg RCC_LSEDRIVE_HIGH: LSE oscillator high drive capability.
+ * @retval None
+ */
+#define __HAL_RCC_LSEDRIVE_CONFIG(__LSEDRIVE__) \
+ MODIFY_REG(RCC->BDCR, RCC_BDCR_LSEDRV, (uint32_t)(__LSEDRIVE__))
+
+/**
+ * @brief Macro to configures the wake up from stop clock.
+ * @param __STOPWUCLK__: specifies the clock source used after wake up from stop.
+ * This parameter can be one of the following values:
+ * @arg RCC_STOP_WAKEUPCLOCK_MSI: MSI selected as system clock source
+ * @arg RCC_STOP_WAKEUPCLOCK_HSI: HSI selected as system clock source
+ * @retval None
+ */
+#define __HAL_RCC_WAKEUPSTOP_CLK_CONFIG(__STOPWUCLK__) \
+ MODIFY_REG(RCC->CFGR, RCC_CFGR_STOPWUCK, (__STOPWUCLK__))
+
+
+/** @defgroup RCC_Flags_Interrupts_Management Flags Interrupts Management
+ * @brief macros to manage the specified RCC Flags and interrupts.
+ * @{
+ */
+
+/** @brief Enable RCC interrupt (Perform Byte access to RCC_CIR[14:8] bits to enable
+ * the selected interrupts).
+ * @param __INTERRUPT__: specifies the RCC interrupt sources to be enabled.
+ * This parameter can be any combination of the following values:
+ * @arg RCC_IT_LSIRDY: LSI ready interrupt
+ * @arg RCC_IT_LSERDY: LSE ready interrupt
+ * @arg RCC_IT_MSIRDY: HSI ready interrupt
+ * @arg RCC_IT_HSIRDY: HSI ready interrupt
+ * @arg RCC_IT_HSERDY: HSE ready interrupt
+ * @arg RCC_IT_PLLRDY: main PLL ready interrupt
+ * @arg RCC_IT_PLLSAI1RDY: PLLSAI1 ready interrupt
+ * @arg RCC_IT_PLLSAI2RDY: PLLSAI2 ready interrupt
+ * @arg RCC_IT_LSECSS: Clock security system interrupt
+ * @retval None
+ */
+#define __HAL_RCC_ENABLE_IT(__INTERRUPT__) SET_BIT(RCC->CIER, (__INTERRUPT__))
+
+/** @brief Disable RCC interrupt (Perform Byte access to RCC_CIR[14:8] bits to disable
+ * the selected interrupts).
+ * @param __INTERRUPT__: specifies the RCC interrupt sources to be disabled.
+ * This parameter can be any combination of the following values:
+ * @arg RCC_IT_LSIRDY: LSI ready interrupt
+ * @arg RCC_IT_LSERDY: LSE ready interrupt
+ * @arg RCC_IT_MSIRDY: HSI ready interrupt
+ * @arg RCC_IT_HSIRDY: HSI ready interrupt
+ * @arg RCC_IT_HSERDY: HSE ready interrupt
+ * @arg RCC_IT_PLLRDY: main PLL ready interrupt
+ * @arg RCC_IT_PLLSAI1RDY: PLLSAI1 ready interrupt
+ * @arg RCC_IT_PLLSAI2RDY: PLLSAI2 ready interrupt
+ * @arg RCC_IT_LSECSS: Clock security system interrupt
+ * @retval None
+ */
+#define __HAL_RCC_DISABLE_IT(__INTERRUPT__) CLEAR_BIT(RCC->CIER, (__INTERRUPT__))
+
+/** @brief Clear the RCC's interrupt pending bits (Perform Byte access to RCC_CIR[23:16]
+ * bits to clear the selected interrupt pending bits.
+ * @param __INTERRUPT__: specifies the interrupt pending bit to clear.
+ * This parameter can be any combination of the following values:
+ * @arg RCC_IT_LSIRDY: LSI ready interrupt
+ * @arg RCC_IT_LSERDY: LSE ready interrupt
+ * @arg RCC_IT_MSIRDY: MSI ready interrupt
+ * @arg RCC_IT_HSIRDY: HSI ready interrupt
+ * @arg RCC_IT_HSERDY: HSE ready interrupt
+ * @arg RCC_IT_PLLRDY: main PLL ready interrupt
+ * @arg RCC_IT_PLLSAI1RDY: PLLSAI1 ready interrupt
+ * @arg RCC_IT_PLLSAI2RDY: PLLSAI2 ready interrupt
+ * @arg RCC_IT_HSECSS: HSE Clock Security interrupt
+ * @arg RCC_IT_LSECSS: Clock security system interrupt
+ * @retval None
+ */
+#define __HAL_RCC_CLEAR_IT(__INTERRUPT__) (RCC->CICR = (__INTERRUPT__))
+
+/** @brief Check whether the RCC interrupt has occurred or not.
+ * @param __INTERRUPT__: specifies the RCC interrupt source to check.
+ * This parameter can be one of the following values:
+ * @arg RCC_IT_LSIRDY: LSI ready interrupt
+ * @arg RCC_IT_LSERDY: LSE ready interrupt
+ * @arg RCC_IT_MSIRDY: MSI ready interrupt
+ * @arg RCC_IT_HSIRDY: HSI ready interrupt
+ * @arg RCC_IT_HSERDY: HSE ready interrupt
+ * @arg RCC_IT_PLLRDY: main PLL ready interrupt
+ * @arg RCC_IT_PLLSAI1RDY: PLLSAI1 ready interrupt
+ * @arg RCC_IT_PLLSAI2RDY: PLLSAI2 ready interrupt
+ * @arg RCC_IT_HSECSS: HSE Clock Security interrupt
+ * @arg RCC_IT_LSECSS: Clock security system interrupt
+ * @retval The new state of __INTERRUPT__ (TRUE or FALSE).
+ */
+#define __HAL_RCC_GET_IT_SOURCE(__INTERRUPT__) ((RCC->CIFR & (__INTERRUPT__)) == (__INTERRUPT__))
+
+/** @brief Set RMVF bit to clear the reset flags.
+ * The reset flags are: RCC_FLAG_FWRRST, RCC_FLAG_OBLRST, RCC_FLAG_PINRST, RCC_FLAG_BORRST,
+ * RCC_FLAG_SFTRST, RCC_FLAG_IWDGRST, RCC_FLAG_WWDGRST and RCC_FLAG_LPWRRST.
+ * @retval None
+ */
+#define __HAL_RCC_CLEAR_RESET_FLAGS() (RCC->CSR |= RCC_CSR_RMVF)
+
+/** @brief Check whether the selected RCC flag is set or not.
+ * @param __FLAG__: specifies the flag to check.
+ * This parameter can be one of the following values:
+ * @arg RCC_FLAG_MSIRDY: MSI oscillator clock ready
+ * @arg RCC_FLAG_HSIRDY: HSI oscillator clock ready
+ * @arg RCC_FLAG_HSERDY: HSE oscillator clock ready
+ * @arg RCC_FLAG_PLLRDY: main PLL clock ready
+ * @arg RCC_FLAG_PLLSAI2RDY: PLLSAI2 clock ready
+ * @arg RCC_FLAG_PLLSAI1RDY: PLLSAI1 clock ready
+ * @arg RCC_FLAG_LSERDY: LSE oscillator clock ready
+ * @arg RCC_FLAG_LSECSSD: Clock security system failure on LSE oscillator detection
+ * @arg RCC_FLAG_LSIRDY: LSI oscillator clock ready
+ * @arg RCC_FLAG_BORRST: BOR reset
+ * @arg RCC_FLAG_OBLRST: OBLRST reset
+ * @arg RCC_FLAG_PINRST: Pin reset
+ * @arg RCC_FLAG_FWRST: FIREWALL reset
+ * @arg RCC_FLAG_RMVF: Remove reset Flag
+ * @arg RCC_FLAG_SFTRST: Software reset
+ * @arg RCC_FLAG_IWDGRST: Independent Watchdog reset
+ * @arg RCC_FLAG_WWDGRST: Window Watchdog reset
+ * @arg RCC_FLAG_LPWRRST: Low Power reset
+ * @retval The new state of __FLAG__ (TRUE or FALSE).
+ */
+#define __HAL_RCC_GET_FLAG(__FLAG__) (((((((__FLAG__) >> 5U) == 1U) ? RCC->CR : \
+ ((((__FLAG__) >> 5U) == 2U) ? RCC->BDCR : \
+ ((((__FLAG__) >> 5U) == 3U) ? RCC->CSR : RCC->CIFR))) & \
+ ((uint32_t)1 << ((__FLAG__) & RCC_FLAG_MASK))) != 0) \
+ ? 1 : 0)
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/* Private constants ---------------------------------------------------------*/
+/** @defgroup RCC_Private_Constants RCC Private Constants
+ * @{
+ */
+/* Defines used for Flags */
+#define CR_REG_INDEX ((uint8_t)1)
+#define BDCR_REG_INDEX ((uint8_t)2)
+#define CSR_REG_INDEX ((uint8_t)3)
+
+#define RCC_FLAG_MASK ((uint8_t)0x1F)
+/**
+ * @}
+ */
+
+/* Private macros ------------------------------------------------------------*/
+/** @addtogroup RCC_Private_Macros
+ * @{
+ */
+
+#define IS_RCC_OSCILLATORTYPE(__OSCILLATOR__) (((__OSCILLATOR__) == RCC_OSCILLATORTYPE_NONE) || \
+ (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_HSE) == RCC_OSCILLATORTYPE_HSE) || \
+ (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_HSI) == RCC_OSCILLATORTYPE_HSI) || \
+ (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_MSI) == RCC_OSCILLATORTYPE_MSI) || \
+ (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_LSI) == RCC_OSCILLATORTYPE_LSI) || \
+ (((__OSCILLATOR__) & RCC_OSCILLATORTYPE_LSE) == RCC_OSCILLATORTYPE_LSE))
+
+#define IS_RCC_HSE(__HSE__) (((__HSE__) == RCC_HSE_OFF) || ((__HSE__) == RCC_HSE_ON) || \
+ ((__HSE__) == RCC_HSE_BYPASS))
+
+#define IS_RCC_LSE(__LSE__) (((__LSE__) == RCC_LSE_OFF) || ((__LSE__) == RCC_LSE_ON) || \
+ ((__LSE__) == RCC_LSE_BYPASS))
+
+#define IS_RCC_HSI(__HSI__) (((__HSI__) == RCC_HSI_OFF) || ((__HSI__) == RCC_HSI_ON))
+
+#define IS_RCC_CALIBRATION_VALUE(__VALUE__) ((__VALUE__) <= (uint32_t)31)
+
+#define IS_RCC_LSI(__LSI__) (((__LSI__) == RCC_LSI_OFF) || ((__LSI__) == RCC_LSI_ON))
+
+#define IS_RCC_MSI(__MSI__) (((__MSI__) == RCC_MSI_OFF) || ((__MSI__) == RCC_MSI_ON))
+
+#define IS_RCC_MSICALIBRATION_VALUE(__VALUE__) ((__VALUE__) <= (uint32_t)255)
+
+#define IS_RCC_PLL(__PLL__) (((__PLL__) == RCC_PLL_NONE) ||((__PLL__) == RCC_PLL_OFF) || \
+ ((__PLL__) == RCC_PLL_ON))
+
+#define IS_RCC_PLLSOURCE(__SOURCE__) (((__SOURCE__) == RCC_PLLSOURCE_NONE) || \
+ ((__SOURCE__) == RCC_PLLSOURCE_MSI) || \
+ ((__SOURCE__) == RCC_PLLSOURCE_HSI) || \
+ ((__SOURCE__) == RCC_PLLSOURCE_HSE))
+
+#define IS_RCC_PLLM_VALUE(__VALUE__) ((__VALUE__) <= 8)
+
+#define IS_RCC_PLLN_VALUE(__VALUE__) ((8 <= (__VALUE__)) && ((__VALUE__) <= 86))
+
+#define IS_RCC_PLLP_VALUE(__VALUE__) (((__VALUE__) == 7) || ((__VALUE__) == 17) )
+
+#define IS_RCC_PLLQ_VALUE(__VALUE__) (((__VALUE__) == 2 ) || ((__VALUE__) == 4) || \
+ ((__VALUE__) == 6) || ((__VALUE__) == 8))
+
+#define IS_RCC_PLLR_VALUE(__VALUE__) (((__VALUE__) == 2 ) || ((__VALUE__) == 4) || \
+ ((__VALUE__) == 6) || ((__VALUE__) == 8))
+
+#define IS_RCC_PLLSAI1CLOCKOUT_VALUE(__VALUE__) (((((__VALUE__) & RCC_PLLSAI1_SAI1CLK) == RCC_PLLSAI1_SAI1CLK) || \
+ (((__VALUE__) & RCC_PLLSAI1_48M2CLK) == RCC_PLLSAI1_48M2CLK) || \
+ (((__VALUE__) & RCC_PLLSAI1_ADC1CLK) == RCC_PLLSAI1_ADC1CLK)) && \
+ (((__VALUE__) & ~(RCC_PLLSAI1_SAI1CLK|RCC_PLLSAI1_48M2CLK|RCC_PLLSAI1_ADC1CLK)) == 0))
+
+#define IS_RCC_PLLSAI2CLOCKOUT_VALUE(__VALUE__) (((((__VALUE__) & RCC_PLLSAI2_SAI2CLK) == RCC_PLLSAI2_SAI2CLK ) || \
+ (((__VALUE__) & RCC_PLLSAI2_ADC2CLK) == RCC_PLLSAI2_ADC2CLK)) && \
+ (((__VALUE__) & ~(RCC_PLLSAI2_SAI2CLK|RCC_PLLSAI2_ADC2CLK)) == 0))
+
+#define IS_RCC_MSI_CLOCK_RANGE(__RANGE__) (((__RANGE__) == RCC_MSIRANGE_0) || \
+ ((__RANGE__) == RCC_MSIRANGE_1) || \
+ ((__RANGE__) == RCC_MSIRANGE_2) || \
+ ((__RANGE__) == RCC_MSIRANGE_3) || \
+ ((__RANGE__) == RCC_MSIRANGE_4) || \
+ ((__RANGE__) == RCC_MSIRANGE_5) || \
+ ((__RANGE__) == RCC_MSIRANGE_6) || \
+ ((__RANGE__) == RCC_MSIRANGE_7) || \
+ ((__RANGE__) == RCC_MSIRANGE_8) || \
+ ((__RANGE__) == RCC_MSIRANGE_9) || \
+ ((__RANGE__) == RCC_MSIRANGE_10) || \
+ ((__RANGE__) == RCC_MSIRANGE_11))
+
+#define IS_RCC_MSI_STANDBY_CLOCK_RANGE(__RANGE__) (((__RANGE__) == RCC_MSIRANGE_4) || \
+ ((__RANGE__) == RCC_MSIRANGE_5) || \
+ ((__RANGE__) == RCC_MSIRANGE_6) || \
+ ((__RANGE__) == RCC_MSIRANGE_7))
+
+#define IS_RCC_CLOCKTYPE(__CLK__) ((1 <= (__CLK__)) && ((__CLK__) <= 15))
+
+#define IS_RCC_SYSCLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_SYSCLKSOURCE_MSI) || \
+ ((__SOURCE__) == RCC_SYSCLKSOURCE_HSI) || \
+ ((__SOURCE__) == RCC_SYSCLKSOURCE_HSE) || \
+ ((__SOURCE__) == RCC_SYSCLKSOURCE_PLLCLK))
+
+#define IS_RCC_HCLK(__HCLK__) (((__HCLK__) == RCC_SYSCLK_DIV1) || ((__HCLK__) == RCC_SYSCLK_DIV2) || \
+ ((__HCLK__) == RCC_SYSCLK_DIV4) || ((__HCLK__) == RCC_SYSCLK_DIV8) || \
+ ((__HCLK__) == RCC_SYSCLK_DIV16) || ((__HCLK__) == RCC_SYSCLK_DIV64) || \
+ ((__HCLK__) == RCC_SYSCLK_DIV128) || ((__HCLK__) == RCC_SYSCLK_DIV256) || \
+ ((__HCLK__) == RCC_SYSCLK_DIV512))
+
+#define IS_RCC_PCLK(__PCLK__) (((__PCLK__) == RCC_HCLK_DIV1) || ((__PCLK__) == RCC_HCLK_DIV2) || \
+ ((__PCLK__) == RCC_HCLK_DIV4) || ((__PCLK__) == RCC_HCLK_DIV8) || \
+ ((__PCLK__) == RCC_HCLK_DIV16))
+
+#define IS_RCC_RTCCLKSOURCE(__SOURCE__) (((__SOURCE__) == RCC_RTCCLKSOURCE_LSE) || \
+ ((__SOURCE__) == RCC_RTCCLKSOURCE_LSI) || \
+ ((__SOURCE__) == RCC_RTCCLKSOURCE_HSE_DIV32))
+
+#define IS_RCC_MCO(__MCOX__) ((__MCOX__) == RCC_MCO1)
+
+#define IS_RCC_MCO1SOURCE(__SOURCE__) (((__SOURCE__) == RCC_MCO1SOURCE_SYSCLK) || \
+ ((__SOURCE__) == RCC_MCO1SOURCE_MSI) || \
+ ((__SOURCE__) == RCC_MCO1SOURCE_HSI) || \
+ ((__SOURCE__) == RCC_MCO1SOURCE_HSE) || \
+ ((__SOURCE__) == RCC_MCO1SOURCE_PLLCLK) || \
+ ((__SOURCE__) == RCC_MCO1SOURCE_LSI) || \
+ ((__SOURCE__) == RCC_MCO1SOURCE_LSE))
+
+#define IS_RCC_MCODIV(__DIV__) (((__DIV__) == RCC_MCODIV_1) || ((__DIV__) == RCC_MCODIV_2) || \
+ ((__DIV__) == RCC_MCODIV_4) || ((__DIV__) == RCC_MCODIV_8) || \
+ ((__DIV__) == RCC_MCODIV_16))
+
+#define IS_RCC_LSE_DRIVE(__DRIVE__) (((__DRIVE__) == RCC_LSEDRIVE_LOW) || \
+ ((__DRIVE__) == RCC_LSEDRIVE_MEDIUMLOW) || \
+ ((__DRIVE__) == RCC_LSEDRIVE_MEDIUMHIGH) || \
+ ((__DRIVE__) == RCC_LSEDRIVE_HIGH))
+
+#define IS_RCC_STOP_WAKEUPCLOCK(__SOURCE__) (((__SOURCE__) == RCC_STOP_WAKEUPCLOCK_MSI) || \
+ ((__SOURCE__) == RCC_STOP_WAKEUPCLOCK_HSI))
+/**
+ * @}
+ */
+
+/* Include RCC HAL Extended module */
+#include "stm32l4xx_hal_rcc_ex.h"
+
+/* Exported functions --------------------------------------------------------*/
+/** @addtogroup RCC_Exported_Functions
+ * @{
+ */
+
+
+/** @addtogroup RCC_Exported_Functions_Group1
+ * @{
+ */
+
+/* Initialization and de-initialization functions ******************************/
+void HAL_RCC_DeInit(void);
+HAL_StatusTypeDef HAL_RCC_OscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct);
+HAL_StatusTypeDef HAL_RCC_ClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t FLatency);
+
+/**
+ * @}
+ */
+
+/** @addtogroup RCC_Exported_Functions_Group2
+ * @{
+ */
+
+/* Peripheral Control functions ************************************************/
+void HAL_RCC_MCOConfig(uint32_t RCC_MCOx, uint32_t RCC_MCOSource, uint32_t RCC_MCODiv);
+void HAL_RCC_EnableCSS(void);
+uint32_t HAL_RCC_GetSysClockFreq(void);
+uint32_t HAL_RCC_GetHCLKFreq(void);
+uint32_t HAL_RCC_GetPCLK1Freq(void);
+uint32_t HAL_RCC_GetPCLK2Freq(void);
+void HAL_RCC_GetOscConfig(RCC_OscInitTypeDef *RCC_OscInitStruct);
+void HAL_RCC_GetClockConfig(RCC_ClkInitTypeDef *RCC_ClkInitStruct, uint32_t *pFLatency);
+/* CSS NMI IRQ handler */
+void HAL_RCC_NMI_IRQHandler(void);
+/* User Callbacks in non blocking mode (IT mode) */
+void HAL_RCC_CSSCallback(void);
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+/**
+ * @}
+ */
+
+#ifdef __cplusplus
+}
+#endif
+
+#endif /* __STM32L4xx_HAL_RCC_H */
+
+/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/