NXP
RT1050 GUI demo using emWin library
Diff: source/pin_mux.c
- Revision:
- 0:dd702039127a
--- /dev/null Thu Jan 01 00:00:00 1970 +0000
+++ b/source/pin_mux.c Thu Sep 20 19:16:34 2018 +0000
@@ -0,0 +1,1101 @@
+/*
+ * The Clear BSD License
+ * Copyright 2017-2018 NXP
+ * All rights reserved.
+ *
+ * Redistribution and use in source and binary forms, with or without modification,
+ * are permitted (subject to the limitations in the disclaimer below) provided
+ * that the following conditions are met:
+ *
+ * o Redistributions of source code must retain the above copyright notice, this list
+ * of conditions and the following disclaimer.
+ *
+ * o Redistributions in binary form must reproduce the above copyright notice, this
+ * list of conditions and the following disclaimer in the documentation and/or
+ * other materials provided with the distribution.
+ *
+ * o Neither the name of the copyright holder nor the names of its
+ * contributors may be used to endorse or promote products derived from this
+ * software without specific prior written permission.
+ *
+ * NO EXPRESS OR IMPLIED LICENSES TO ANY PARTY'S PATENT RIGHTS ARE GRANTED BY THIS LICENSE.
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
+ * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
+ * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
+ * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR
+ * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+ * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+ * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
+ * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
+ * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
+ * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+ */
+
+/***********************************************************************************************************************
+ * This file was generated by the MCUXpresso Config Tools. Any manual edits made to this file
+ * will be overwritten if the respective MCUXpresso Config Tools is used to update this file.
+ **********************************************************************************************************************/
+
+/*
+ * TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+!!GlobalInfo
+product: Pins v4.1
+processor: MIMXRT1052xxxxB
+package_id: MIMXRT1052DVL6B
+mcu_data: ksdk2_0
+processor_version: 0.0.0
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS ***********
+ */
+
+#include "fsl_common.h"
+#include "fsl_iomuxc.h"
+#include "pin_mux.h"
+
+/* FUNCTION ************************************************************************************************************
+ *
+ * Function Name : BOARD_InitBootPins
+ * Description : Calls initialization functions.
+ *
+ * END ****************************************************************************************************************/
+void BOARD_InitBootPins(void) {
+ BOARD_InitPins();
+ BOARD_InitI2C1Pins();
+}
+
+/*
+ * TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+BOARD_InitPins:
+- options: {callFromInitBoot: 'true', coreID: core0, enableClock: 'true'}
+- pin_list:
+ - {pin_num: L14, peripheral: LPUART1, signal: RX, pin_signal: GPIO_AD_B0_13, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: K14, peripheral: LPUART1, signal: TX, pin_signal: GPIO_AD_B0_12, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: D7, peripheral: LCDIF, signal: lcdif_clk, pin_signal: GPIO_B0_00, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: C8, peripheral: LCDIF, signal: 'lcdif_data, 00', pin_signal: GPIO_B0_04, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: B8, peripheral: LCDIF, signal: 'lcdif_data, 01', pin_signal: GPIO_B0_05, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: A8, peripheral: LCDIF, signal: 'lcdif_data, 02', pin_signal: GPIO_B0_06, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: A9, peripheral: LCDIF, signal: 'lcdif_data, 03', pin_signal: GPIO_B0_07, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: B9, peripheral: LCDIF, signal: 'lcdif_data, 04', pin_signal: GPIO_B0_08, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: C9, peripheral: LCDIF, signal: 'lcdif_data, 05', pin_signal: GPIO_B0_09, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: D9, peripheral: LCDIF, signal: 'lcdif_data, 06', pin_signal: GPIO_B0_10, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: A10, peripheral: LCDIF, signal: 'lcdif_data, 07', pin_signal: GPIO_B0_11, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: C10, peripheral: LCDIF, signal: 'lcdif_data, 08', pin_signal: GPIO_B0_12, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: D10, peripheral: LCDIF, signal: 'lcdif_data, 09', pin_signal: GPIO_B0_13, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: E10, peripheral: LCDIF, signal: 'lcdif_data, 10', pin_signal: GPIO_B0_14, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: E11, peripheral: LCDIF, signal: 'lcdif_data, 11', pin_signal: GPIO_B0_15, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: A11, peripheral: LCDIF, signal: 'lcdif_data, 12', pin_signal: GPIO_B1_00, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: B11, peripheral: LCDIF, signal: 'lcdif_data, 13', pin_signal: GPIO_B1_01, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: C11, peripheral: LCDIF, signal: 'lcdif_data, 14', pin_signal: GPIO_B1_02, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: D11, peripheral: LCDIF, signal: 'lcdif_data, 15', pin_signal: GPIO_B1_03, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: E7, peripheral: LCDIF, signal: lcdif_enable, pin_signal: GPIO_B0_01, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: E8, peripheral: LCDIF, signal: lcdif_hsync, pin_signal: GPIO_B0_02, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: D8, peripheral: LCDIF, signal: lcdif_vsync, pin_signal: GPIO_B0_03, software_input_on: Disable, hysteresis_enable: Enable, pull_up_down_config: Pull_Up_100K_Ohm,
+ pull_keeper_select: Pull, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: B14, peripheral: GPIO2, signal: 'gpio_io, 31', pin_signal: GPIO_B1_15, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: M11, peripheral: GPIO1, signal: 'gpio_io, 02', pin_signal: GPIO_AD_B0_02, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS ***********
+ */
+
+/* FUNCTION ************************************************************************************************************
+ *
+ * Function Name : BOARD_InitPins
+ * Description : Configures pin routing and optionally pin electrical features.
+ *
+ * END ****************************************************************************************************************/
+void BOARD_InitPins(void) {
+ CLOCK_EnableClock(kCLOCK_Iomuxc); /* iomuxc clock (iomuxc_clk_enable): 0x03u */
+
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_AD_B0_02_GPIO1_IO02, /* GPIO_AD_B0_02 is configured as GPIO1_IO02 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_AD_B0_12_LPUART1_TX, /* GPIO_AD_B0_12 is configured as LPUART1_TX */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_AD_B0_13_LPUART1_RX, /* GPIO_AD_B0_13 is configured as LPUART1_RX */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B0_00_LCD_CLK, /* GPIO_B0_00 is configured as LCD_CLK */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B0_01_LCD_ENABLE, /* GPIO_B0_01 is configured as LCD_ENABLE */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B0_02_LCD_HSYNC, /* GPIO_B0_02 is configured as LCD_HSYNC */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B0_03_LCD_VSYNC, /* GPIO_B0_03 is configured as LCD_VSYNC */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B0_04_LCD_DATA00, /* GPIO_B0_04 is configured as LCD_DATA00 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B0_05_LCD_DATA01, /* GPIO_B0_05 is configured as LCD_DATA01 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B0_06_LCD_DATA02, /* GPIO_B0_06 is configured as LCD_DATA02 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B0_07_LCD_DATA03, /* GPIO_B0_07 is configured as LCD_DATA03 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B0_08_LCD_DATA04, /* GPIO_B0_08 is configured as LCD_DATA04 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B0_09_LCD_DATA05, /* GPIO_B0_09 is configured as LCD_DATA05 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B0_10_LCD_DATA06, /* GPIO_B0_10 is configured as LCD_DATA06 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B0_11_LCD_DATA07, /* GPIO_B0_11 is configured as LCD_DATA07 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B0_12_LCD_DATA08, /* GPIO_B0_12 is configured as LCD_DATA08 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B0_13_LCD_DATA09, /* GPIO_B0_13 is configured as LCD_DATA09 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B0_14_LCD_DATA10, /* GPIO_B0_14 is configured as LCD_DATA10 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B0_15_LCD_DATA11, /* GPIO_B0_15 is configured as LCD_DATA11 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B1_00_LCD_DATA12, /* GPIO_B1_00 is configured as LCD_DATA12 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B1_01_LCD_DATA13, /* GPIO_B1_01 is configured as LCD_DATA13 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B1_02_LCD_DATA14, /* GPIO_B1_02 is configured as LCD_DATA14 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B1_03_LCD_DATA15, /* GPIO_B1_03 is configured as LCD_DATA15 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_B1_15_GPIO2_IO31, /* GPIO_B1_15 is configured as GPIO2_IO31 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_AD_B0_02_GPIO1_IO02, /* GPIO_AD_B0_02 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_AD_B0_12_LPUART1_TX, /* GPIO_AD_B0_12 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_AD_B0_13_LPUART1_RX, /* GPIO_AD_B0_13 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B0_00_LCD_CLK, /* GPIO_B0_00 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B0_01_LCD_ENABLE, /* GPIO_B0_01 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B0_02_LCD_HSYNC, /* GPIO_B0_02 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B0_03_LCD_VSYNC, /* GPIO_B0_03 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B0_04_LCD_DATA00, /* GPIO_B0_04 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B0_05_LCD_DATA01, /* GPIO_B0_05 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B0_06_LCD_DATA02, /* GPIO_B0_06 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B0_07_LCD_DATA03, /* GPIO_B0_07 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B0_08_LCD_DATA04, /* GPIO_B0_08 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B0_09_LCD_DATA05, /* GPIO_B0_09 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B0_10_LCD_DATA06, /* GPIO_B0_10 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B0_11_LCD_DATA07, /* GPIO_B0_11 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B0_12_LCD_DATA08, /* GPIO_B0_12 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B0_13_LCD_DATA09, /* GPIO_B0_13 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B0_14_LCD_DATA10, /* GPIO_B0_14 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B0_15_LCD_DATA11, /* GPIO_B0_15 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B1_00_LCD_DATA12, /* GPIO_B1_00 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B1_01_LCD_DATA13, /* GPIO_B1_01 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B1_02_LCD_DATA14, /* GPIO_B1_02 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B1_03_LCD_DATA15, /* GPIO_B1_03 PAD functional properties : */
+ 0x01B0B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Pull
+ Pull Up / Down Config. Field: 100K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Enabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_B1_15_GPIO2_IO31, /* GPIO_B1_15 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+}
+
+
+/*
+ * TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+BOARD_InitSemcPins:
+- options: {coreID: core0, enableClock: 'true'}
+- pin_list:
+ - {pin_num: C2, peripheral: SEMC, signal: 'ADDR, 00', pin_signal: GPIO_EMC_09, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: G1, peripheral: SEMC, signal: 'ADDR, 01', pin_signal: GPIO_EMC_10, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: G3, peripheral: SEMC, signal: 'ADDR, 02', pin_signal: GPIO_EMC_11, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: H1, peripheral: SEMC, signal: 'ADDR, 03', pin_signal: GPIO_EMC_12, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: A6, peripheral: SEMC, signal: 'ADDR, 04', pin_signal: GPIO_EMC_13, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: B6, peripheral: SEMC, signal: 'ADDR, 05', pin_signal: GPIO_EMC_14, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: B1, peripheral: SEMC, signal: 'ADDR, 06', pin_signal: GPIO_EMC_15, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: A5, peripheral: SEMC, signal: 'ADDR, 07', pin_signal: GPIO_EMC_16, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: A4, peripheral: SEMC, signal: 'ADDR, 08', pin_signal: GPIO_EMC_17, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: B2, peripheral: SEMC, signal: 'ADDR, 09', pin_signal: GPIO_EMC_18, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: G2, peripheral: SEMC, signal: 'ADDR, 10', pin_signal: GPIO_EMC_23, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: B4, peripheral: SEMC, signal: 'ADDR, 11', pin_signal: GPIO_EMC_19, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: A3, peripheral: SEMC, signal: 'ADDR, 12', pin_signal: GPIO_EMC_20, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: C1, peripheral: SEMC, signal: 'BA, 0', pin_signal: GPIO_EMC_21, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: F1, peripheral: SEMC, signal: 'BA, 1', pin_signal: GPIO_EMC_22, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: D3, peripheral: SEMC, signal: semc_cas, pin_signal: GPIO_EMC_24, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: A2, peripheral: SEMC, signal: semc_cke, pin_signal: GPIO_EMC_27, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: B3, peripheral: SEMC, signal: semc_clk, pin_signal: GPIO_EMC_26, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: E1, peripheral: SEMC, signal: 'CS, 0', pin_signal: GPIO_EMC_29, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: E3, peripheral: SEMC, signal: 'DATA, 00', pin_signal: GPIO_EMC_00, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: F3, peripheral: SEMC, signal: 'DATA, 01', pin_signal: GPIO_EMC_01, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: F4, peripheral: SEMC, signal: 'DATA, 02', pin_signal: GPIO_EMC_02, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: G4, peripheral: SEMC, signal: 'DATA, 03', pin_signal: GPIO_EMC_03, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: F2, peripheral: SEMC, signal: 'DATA, 04', pin_signal: GPIO_EMC_04, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: G5, peripheral: SEMC, signal: 'DATA, 05', pin_signal: GPIO_EMC_05, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: H5, peripheral: SEMC, signal: 'DATA, 06', pin_signal: GPIO_EMC_06, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: H4, peripheral: SEMC, signal: 'DATA, 07', pin_signal: GPIO_EMC_07, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: C6, peripheral: SEMC, signal: 'DATA, 08', pin_signal: GPIO_EMC_30, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: C5, peripheral: SEMC, signal: 'DATA, 09', pin_signal: GPIO_EMC_31, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: D5, peripheral: SEMC, signal: 'DATA, 10', pin_signal: GPIO_EMC_32, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: C4, peripheral: SEMC, signal: 'DATA, 11', pin_signal: GPIO_EMC_33, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: D4, peripheral: SEMC, signal: 'DATA, 12', pin_signal: GPIO_EMC_34, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: E5, peripheral: SEMC, signal: 'DATA, 13', pin_signal: GPIO_EMC_35, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: C3, peripheral: SEMC, signal: 'DATA, 14', pin_signal: GPIO_EMC_36, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: E4, peripheral: SEMC, signal: 'DATA, 15', pin_signal: GPIO_EMC_37, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: H3, peripheral: SEMC, signal: 'DM, 0', pin_signal: GPIO_EMC_08, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: D6, peripheral: SEMC, signal: 'DM, 1', pin_signal: GPIO_EMC_38, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: D2, peripheral: SEMC, signal: semc_ras, pin_signal: GPIO_EMC_25, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: D1, peripheral: SEMC, signal: semc_we, pin_signal: GPIO_EMC_28, software_input_on: Disable, hysteresis_enable: Disable, pull_up_down_config: Pull_Down_100K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Disable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS ***********
+ */
+
+/* FUNCTION ************************************************************************************************************
+ *
+ * Function Name : BOARD_InitSemcPins
+ * Description : Configures pin routing and optionally pin electrical features.
+ *
+ * END ****************************************************************************************************************/
+void BOARD_InitSemcPins(void) {
+ CLOCK_EnableClock(kCLOCK_Iomuxc); /* iomuxc clock (iomuxc_clk_enable): 0x03u */
+
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_00_SEMC_DATA00, /* GPIO_EMC_00 is configured as SEMC_DATA00 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_01_SEMC_DATA01, /* GPIO_EMC_01 is configured as SEMC_DATA01 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_02_SEMC_DATA02, /* GPIO_EMC_02 is configured as SEMC_DATA02 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_03_SEMC_DATA03, /* GPIO_EMC_03 is configured as SEMC_DATA03 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_04_SEMC_DATA04, /* GPIO_EMC_04 is configured as SEMC_DATA04 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_05_SEMC_DATA05, /* GPIO_EMC_05 is configured as SEMC_DATA05 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_06_SEMC_DATA06, /* GPIO_EMC_06 is configured as SEMC_DATA06 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_07_SEMC_DATA07, /* GPIO_EMC_07 is configured as SEMC_DATA07 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_08_SEMC_DM00, /* GPIO_EMC_08 is configured as SEMC_DM00 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_09_SEMC_ADDR00, /* GPIO_EMC_09 is configured as SEMC_ADDR00 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_10_SEMC_ADDR01, /* GPIO_EMC_10 is configured as SEMC_ADDR01 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_11_SEMC_ADDR02, /* GPIO_EMC_11 is configured as SEMC_ADDR02 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_12_SEMC_ADDR03, /* GPIO_EMC_12 is configured as SEMC_ADDR03 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_13_SEMC_ADDR04, /* GPIO_EMC_13 is configured as SEMC_ADDR04 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_14_SEMC_ADDR05, /* GPIO_EMC_14 is configured as SEMC_ADDR05 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_15_SEMC_ADDR06, /* GPIO_EMC_15 is configured as SEMC_ADDR06 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_16_SEMC_ADDR07, /* GPIO_EMC_16 is configured as SEMC_ADDR07 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_17_SEMC_ADDR08, /* GPIO_EMC_17 is configured as SEMC_ADDR08 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_18_SEMC_ADDR09, /* GPIO_EMC_18 is configured as SEMC_ADDR09 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_19_SEMC_ADDR11, /* GPIO_EMC_19 is configured as SEMC_ADDR11 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_20_SEMC_ADDR12, /* GPIO_EMC_20 is configured as SEMC_ADDR12 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_21_SEMC_BA0, /* GPIO_EMC_21 is configured as SEMC_BA0 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_22_SEMC_BA1, /* GPIO_EMC_22 is configured as SEMC_BA1 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_23_SEMC_ADDR10, /* GPIO_EMC_23 is configured as SEMC_ADDR10 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_24_SEMC_CAS, /* GPIO_EMC_24 is configured as SEMC_CAS */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_25_SEMC_RAS, /* GPIO_EMC_25 is configured as SEMC_RAS */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_26_SEMC_CLK, /* GPIO_EMC_26 is configured as SEMC_CLK */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_27_SEMC_CKE, /* GPIO_EMC_27 is configured as SEMC_CKE */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_28_SEMC_WE, /* GPIO_EMC_28 is configured as SEMC_WE */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_29_SEMC_CS0, /* GPIO_EMC_29 is configured as SEMC_CS0 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_30_SEMC_DATA08, /* GPIO_EMC_30 is configured as SEMC_DATA08 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_31_SEMC_DATA09, /* GPIO_EMC_31 is configured as SEMC_DATA09 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_32_SEMC_DATA10, /* GPIO_EMC_32 is configured as SEMC_DATA10 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_33_SEMC_DATA11, /* GPIO_EMC_33 is configured as SEMC_DATA11 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_34_SEMC_DATA12, /* GPIO_EMC_34 is configured as SEMC_DATA12 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_35_SEMC_DATA13, /* GPIO_EMC_35 is configured as SEMC_DATA13 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_36_SEMC_DATA14, /* GPIO_EMC_36 is configured as SEMC_DATA14 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_37_SEMC_DATA15, /* GPIO_EMC_37 is configured as SEMC_DATA15 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_EMC_38_SEMC_DM01, /* GPIO_EMC_38 is configured as SEMC_DM01 */
+ 0U); /* Software Input On Field: Input Path is determined by functionality */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_00_SEMC_DATA00, /* GPIO_EMC_00 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_01_SEMC_DATA01, /* GPIO_EMC_01 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_02_SEMC_DATA02, /* GPIO_EMC_02 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_03_SEMC_DATA03, /* GPIO_EMC_03 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_04_SEMC_DATA04, /* GPIO_EMC_04 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_05_SEMC_DATA05, /* GPIO_EMC_05 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_06_SEMC_DATA06, /* GPIO_EMC_06 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_07_SEMC_DATA07, /* GPIO_EMC_07 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_08_SEMC_DM00, /* GPIO_EMC_08 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_09_SEMC_ADDR00, /* GPIO_EMC_09 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_10_SEMC_ADDR01, /* GPIO_EMC_10 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_11_SEMC_ADDR02, /* GPIO_EMC_11 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_12_SEMC_ADDR03, /* GPIO_EMC_12 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_13_SEMC_ADDR04, /* GPIO_EMC_13 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_14_SEMC_ADDR05, /* GPIO_EMC_14 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_15_SEMC_ADDR06, /* GPIO_EMC_15 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_16_SEMC_ADDR07, /* GPIO_EMC_16 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_17_SEMC_ADDR08, /* GPIO_EMC_17 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_18_SEMC_ADDR09, /* GPIO_EMC_18 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_19_SEMC_ADDR11, /* GPIO_EMC_19 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_20_SEMC_ADDR12, /* GPIO_EMC_20 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_21_SEMC_BA0, /* GPIO_EMC_21 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_22_SEMC_BA1, /* GPIO_EMC_22 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_23_SEMC_ADDR10, /* GPIO_EMC_23 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_24_SEMC_CAS, /* GPIO_EMC_24 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_25_SEMC_RAS, /* GPIO_EMC_25 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_26_SEMC_CLK, /* GPIO_EMC_26 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_27_SEMC_CKE, /* GPIO_EMC_27 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_28_SEMC_WE, /* GPIO_EMC_28 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_29_SEMC_CS0, /* GPIO_EMC_29 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_30_SEMC_DATA08, /* GPIO_EMC_30 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_31_SEMC_DATA09, /* GPIO_EMC_31 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_32_SEMC_DATA10, /* GPIO_EMC_32 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_33_SEMC_DATA11, /* GPIO_EMC_33 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_34_SEMC_DATA12, /* GPIO_EMC_34 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_35_SEMC_DATA13, /* GPIO_EMC_35 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_36_SEMC_DATA14, /* GPIO_EMC_36 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_37_SEMC_DATA15, /* GPIO_EMC_37 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_EMC_38_SEMC_DM01, /* GPIO_EMC_38 PAD functional properties : */
+ 0x10B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Disabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 100K Ohm Pull Down
+ Hyst. Enable Field: Hysteresis Disabled */
+}
+
+
+/*
+ * TEXT BELOW IS USED AS SETTING FOR TOOLS *************************************
+BOARD_InitI2C1Pins:
+- options: {callFromInitBoot: 'true', coreID: core0, enableClock: 'true'}
+- pin_list:
+ - {pin_num: J11, peripheral: LPI2C1, signal: SCL, pin_signal: GPIO_AD_B1_00, software_input_on: Enable, hysteresis_enable: Disable, pull_up_down_config: Pull_Up_22K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Enable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ - {pin_num: K11, peripheral: LPI2C1, signal: SDA, pin_signal: GPIO_AD_B1_01, software_input_on: Enable, hysteresis_enable: Disable, pull_up_down_config: Pull_Up_22K_Ohm,
+ pull_keeper_select: Keeper, pull_keeper_enable: Enable, open_drain: Enable, speed: MHZ_100, drive_strength: R0_6, slew_rate: Slow}
+ * BE CAREFUL MODIFYING THIS COMMENT - IT IS YAML SETTINGS FOR TOOLS ***********
+ */
+
+/* FUNCTION ************************************************************************************************************
+ *
+ * Function Name : BOARD_InitI2C1Pins
+ * Description : Configures pin routing and optionally pin electrical features.
+ *
+ * END ****************************************************************************************************************/
+void BOARD_InitI2C1Pins(void) {
+ CLOCK_EnableClock(kCLOCK_Iomuxc); /* iomuxc clock (iomuxc_clk_enable): 0x03u */
+
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_AD_B1_00_LPI2C1_SCL, /* GPIO_AD_B1_00 is configured as LPI2C1_SCL */
+ 1U); /* Software Input On Field: Force input path of pad GPIO_AD_B1_00 */
+ IOMUXC_SetPinMux(
+ IOMUXC_GPIO_AD_B1_01_LPI2C1_SDA, /* GPIO_AD_B1_01 is configured as LPI2C1_SDA */
+ 1U); /* Software Input On Field: Force input path of pad GPIO_AD_B1_01 */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_AD_B1_00_LPI2C1_SCL, /* GPIO_AD_B1_00 PAD functional properties : */
+ 0xD8B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Enabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 22K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Disabled */
+ IOMUXC_SetPinConfig(
+ IOMUXC_GPIO_AD_B1_01_LPI2C1_SDA, /* GPIO_AD_B1_01 PAD functional properties : */
+ 0xD8B0u); /* Slew Rate Field: Slow Slew Rate
+ Drive Strength Field: R0/6
+ Speed Field: medium(100MHz)
+ Open Drain Enable Field: Open Drain Enabled
+ Pull / Keep Enable Field: Pull/Keeper Enabled
+ Pull / Keep Select Field: Keeper
+ Pull Up / Down Config. Field: 22K Ohm Pull Up
+ Hyst. Enable Field: Hysteresis Disabled */
+}
+
+/***********************************************************************************************************************
+ * EOF
+ **********************************************************************************************************************/